PROVISION OF SECURITY WALL, CHAIN LINK FENCING AND ALLIED WORKS AT QUEENS GARDEN MD OFFRS AND SF ACCN AREAS UNDER GE BELGAUM

Amount

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation over areas n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ disintegrated rock all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Excavation in post holes n.exc 0.5 cum in hard/ dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified

Returning filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread ,levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete type D2 1:4:8 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C2, using 40mm graded stone aggregate in foundation filling and mass concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L for 25mm thick preformed bituminous filler of approved quality filled into expansion joints

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in columns, pillars, piers, posts and struts all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in bands all as specified and directed.

M&L plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in surface channels, drains and similar works all as specified and directed.

M&L for extra for forming fair finished drain or channel of 30cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, Type B1, using 20mm graded stone aggregate, as in kerbs, with rounded or chamferred edges including all mouldings, set in cement mortar 1:6 all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for rough finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides of bands and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 22 but 6mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for mild steel deformed bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

M&L for rolled mild steel angles or flats sections as in posts and struts in fencing and similar work conforming to Fe-290 Gde E-165 including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets for securing wire mesh etc. all as specified and as directed.

Supply only galvanised iron chain link fencing, any mesh, size and type all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type, fixed to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed.

M&L for mild steel screw bolts, machine made, exc. 5mm and n. exc. 10mm dia shank bolt and not. exc 5cm long with hexagonal or square head on one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut all as specified and as directed

S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. all as specified and directed.

M&L for mild steel framed work as in gates of angle or other section with gusset plate, rails, braces etc complete, prepared for hanging or sliding with and including either hook or hinges and hanging fastening and fixing complete conforming to Fe 410W (Gde E-250) all as specified and directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 12mm thick backing coat in cement mortar 1:3 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in claddings, etc. including provision of necessary concealed type epoxy coated 'L' angle brackets/ clips grouted into wall @ 300mm c/c for holding the slabs including rubbing and polishing all as specified and directed.

M&L for rubber coated chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments and glossy finish on top, set, jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking coloured paver blocks, M-40 grade, any shape and size with grey cement and pigments, confirming to IS 15658-2006 all as specified and directed.

M&L for crshed stone sand (M-Ssand/ Robo Sand/i-Sand) filling under floors including watering and consolidation all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for two coats of cement based paint on newly plastered surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F 80mm bore galvanized iron tubes, light grade, with all fittings, fixed into pillars/ columns as in mechanical protection to cables all as specified and directed.

S&F 110mm bore UPVC (SWR) pipes cut to required length fixed into walls as in weep holes all as specified and directed.

M&L for 300mm bore Reinforced cement concrete pipes, class NP2, laid and jointed complete with collars all as specified and as directed.

M&L for bed concrete to 300mm bore drain pipes in Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M/s. VIJAY ELECTRICALS

M/s. KIRAN M CHOUGULE

Shri Sai Associates, Laxmiwadi

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS

SAMARTH ASSOCIATES

M/s.GOODWILL ELECTRICALS

SHRI.H.R.PATIL

M/S MAHADEV M PATIL