Beach front development in Thiruvottriyur.

Amount

Clearing scrub Jungle and Surface dressing of the ground. The rate including hire charges of all machineries, removing of all rubbish from site, lead upto 50m, transportat charges and labour charges etc., complete complying with standard specification.

Earthwork excavation for foundation (for narrow excavation) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. Refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification.

Construction of Embankment with approved Earth materials deposited at site from roadway cutting and excavation from drain and foundation of other structures, graded and compacted to meet requirement of table 300-1, 300-2 of MORTH, in layers not exceeding 250 mm loose thickness, spreading, breaking clods, removal of roots and other organic materials to the required line, grade and cross-section including watering, spreading by Dozer, grading by motor grader and consolidation by vibratory road roller with desired field density not less than 95% of maximum dry density ,including all lead,lift, loading, unloading, all labour, hire charges of all machineries, Transportation, etc., complete in accordance with MORTH technical specification clause No. 305 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Laying the Plain Cement concrete 1:4:8 (One cement four sand and eight broken Machine crushed stone jelly) using HBG Machine creased Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

For Plane surface such as vertical slab ,slide slab of boxing, vertical drops, facia, vertical wall, etc.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing And Laying In Position, Standardised Concrete Mix M-40 Grade In Accordance With 15:456-2000, Using 20mm And Down Graded Hard Broken Granite Stone Jelly For All Rcc Items of Works With Minimum Cement Content of 440 Kg/M3 And Maximum Water Cement Ratio of 0.10, Including Admixture (Plasticiser / Super Plasticser) .In Recommended. Proportions As Per Is:9103. to accelerate, Retard Setting of Concrete, Improve Workability Without Impairing Strength And Durability With About (5.0 Cu.m.) 7730 Kg. of 20mm Machine Crushed Stone Aggregate And With About (3.3 Cu, M.) 5136 Kg. of 10-12mm Machine Crushed Stone Jelly And With About (4.79 Cu.m.) 7670 Kg. of Crushed Stone Sand (M Sand), But Excluding Cost of Reinforcement Grill And Fabricating Charges, Centering And Shuttering And Also Including Laying, Vibrating With Mechanical Vibrators, Finishing, Curing and including pumping charges Etc. And Providing Fixtures Like Fan Clamps In The Rcc Floor/ Roof Slabs Wherever Necessary Without Claiming Extra, Etc., Complete Complying With Standard Specification And As Directed By The Departmental Officers. The Coarse And Fine Aggregates To Be Used Should Comply With The Requirements of Is Standards. (No Separate Payment Will Bemade By The Department For The Excess Tisdae of Materials) (If pumping of Concrete is required).

For Foundation and Basement for 1.0 Cum

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

STRUCTURAL STEEL WORKS: Supplying fabricating, hoisting, erecting and fixing in position Mild steel structural steel works of Pergola, Gate for compound wall and grill at all elevations, levels and heights including aligning, leveling, providing and fixing bolts, nuts, washers, comprising MS plates, flats, squares etc., of various sizes and other structural steel sections confirming to latest IS2062 Grade - A&B including straightening, cutting, welding, bending to shape, bolting and inclusive of the following finishes. The rate including cost of all materials, labour charges, scafolding, stagging, transportation, lead & Lifts, wastage, etc., complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. All MS members shall be painted with one coat of zinc chromite primer and 2 Coats of 35 microns DFT of synthetic enamel paint of approved colour and make etc,.The rate includes the cost of all materials,labour,tools,tackle and plants, wastage etc.,as per specification and drawings complete. The rate quoted is to include cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for. The rate to include preparation of fabrication shop drawings for owner's approval:

Design, fabrication and installation of simple vault tensile fabric work and Steel structure using Belgian make tensile polyester fabric, steel frames by ISO standard acclaimed CE certified installer with structural stability vetting from Anna university ,Chennai having using FLUOMAX Coated Architectural Membrane having tensile strength not less than 4300 N/50mm/ 4200 N/50mm (Warp/Weft) and Tear strength not less than 600 N/ 500 N(Warp/ Weft) of make SIOEN Belgium or equivalent,cables, complete perimeter attachment system, and all normally associated components with machinesfor Fabrication using swiss make Zund cutting machine and Belgian make Architectural Membrane on 20KW Forsstrom High Frequency Welding Machine with SEAMLESS WELDS 50 mm weld width X 1400 mm- Single Stroke all PVC joints shall be formed to a tolerance of +1mm, -1mm and shall be assembled to ensure that seams are always single laid and attaining seamless finish by that a cut edge does not face uphill and membrane used to have a double lacquering made out of highly concentrated FLUOMAX PVDF on both side, double PVC coating and be weldable without grinding

Fly ash Masonry work

Flyash Brick Masonry in cement mortar 1:5 (One cement and five M- sand) in foundations, basement and superstructure walls using Flyash Brick of size 230x110x75mm etc., complete complying with standard specifications and drawings and as directed by departmental Engineers

Flyash brick partition wall in CM 1:3 (One of cement and three of M-sand) 11.50CM thickness using Flyash brick of size 230x110x75mm including both side plastering with CM 1:5 12mm thick and using hoop iron with reinforcement if found necessary. The loop iron shall be should be supplied by department at free of cost.

Providing two legged scaffolding using 15 cm dia casuarinas post of 4 M over all length (3 M Height + 0.5 M Projection + 0.5 M into the Ground) the distance between the two rows being 1.25 M and the spacing of posts being 2.0 M in both the rows with two horizontal posts with 0.5 M. Overlap on either side and braces at 2.0 M Center to center including longitudinal and transverse middle braces to step up and providing a platform with country wood planks of 40 mm thick and 1 M width, etc. in a complete from using coil and nails.

Plastering

Plastering with cement mortar 1:3 (one cement and three P-sand) 12mm thick with P- sand flooring including curing, neat finishing, etc., complete complying with standard specification and as directed by the Departmental officers.

Painting & Water Proofing

Supply and applying water proofing treatment on Retaining walls external surface at Basement, UG Sump, Water tank, Raft sides etc. using cement admixed with water proofing compound in the following order.

i) Making ' V ' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement

ii) Supply and Fixing of 50 long 18 mm dia GI nozzles in the hole of about half the depth of member size along construction joints, and honey comb areas at a spacing not more than 1m c/c.

iii) Supply and Applying injection grouting through the nozzles grouting pumps with a minimum pressure of 2 kg/sqcm with cement slurry admixed with CICO Non shrink Polymeric Water Proof Grouting Compound or approved equivalent at the rate of 2% by weight of cement.

iv) Sealing & cutting of nozzles and leveling the surface using integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.

v)Supply and applying one coat of TAPECRETE Acrylic Polymer Modified Cementitious Slurry Coat over well prepared surface as a Primer and applying CICO CORCHEM 206 - I Polyurethane Based Elastomeric Coating to the thickness of 1.5 mm in 2 coats over TAPECRETE slurry coat applied surface.

vi) Lay protective plaster layer with 12mm thick Cement Mortar 1:4 (1 cement: 4 coarse sand) admixed with Normal setting integral Waterproofing compound CICO NO.1 or approved equivalent conforming to IS 2645 at the rate of 2% by weight of cement over the third coat of brush topping. Plaster shall be cured by spraying of water for the next 7days. The entire water proofing system shall be protected with a 25 mm thick extruded polystrene with necessary low VOC adhesieve.

Supply and laying of respective water proofing treatment at below mentioned locations including all below activities. The surface to be waterproofed shall be cleaned to ensure it is free of laitance, loose particles, oily substance which may affect the adhesion of the waterproofing system, using mechanical rotary wire brush and related tools etc. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportation charges, loading, unloading, preparation of surface, necessary hacking in RCC surface, scaffolding, staging, tools and plants, fuel, curing, cleaning, testing, consumables and also include for conducting leakage test at toilet sunken portion and over head tanks by storing water on the sunken continuously for a period of 7 days etc. as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying water proofing treatment Internal surface of Basement Retaining wall etc., in the following order and consisting of following operations.

i) Making ' V ' grooves at the construction joints of size 20 x 20 mm and clean the surface with wire brush, and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement

ii) Supply and Fixing 18 mm dia GI nozzles (the hole shall be about half the depth of the member to be grouted and nozzle should be 50mm) the retaining wall, along construction joints, and honey comb areas at a spacing not more than 1m c/c . Nozzles (can also) shall be post fixed by drilling holes using drill machine and to be fixed with cement putty admixed with quick setting integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight .

iii) Supply and Applying injection grouting through the nozzles by hand operated grouting pumps with a minimum pressure of 2 kg/sqcm with cement slurry admixed with CICO Non shrink Polymeric Water Proof Grouting Compound or approved equivalent at the rate of 2% by weight of cement .Grouting operations to be taken up after the concrete reached the full strength, i.e 28 days after casting of concrete.

iv) Sealing off the nozzles after grouting operation is over with cement putty admixed with quick setting integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.

v) Cut the projected nozzles if required over the concrete surface and fill with cement putty admixed with quick setting integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.

Supply and laying of respective water proofing treatment at below mentioned locations including all below activities. The surface to be waterproofed shall be cleaned to ensure it is free of laitance, loose particles, oily substance which may affect the adhesion of the waterproofing system, using mechanical rotary wire brush and related tools etc. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportation charges, loading, unloading, preparation of surface, necessary hacking in RCC surface, scaffolding, staging, tools and plants, fuel, curing, cleaning, testing, consumables and also include for conducting leakage test at toilet sunken portion and over head tanks by storing water on the sunken continuously for a period of 7 days etc. as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying water proofing treatment on top of PCC laid for Grade slab, Raft, Pile cap ,footing & beam, UG Sump , Water tank etc., in the following order and consisting of following operations.

i) Supply and applying of one coat of TAPECRETE Acrylic Polymer Cementitious Coating over rendered PCC surface. Application of CORCHEM 206 – I High Build Polyurethane Based Elastomeric Coating to the thickness of 1.5 mm in two coats over TAPECRETE applied surface.

ii)Supply and Fixing 75 mm long 18 mm dia GI nozzles in the hole of about half the depth of member size in grid pattern at a spacing not more than 1.0 meter c/c while casting the raft slab and along construction joints at a spacing not more than 1.0 meter c/c along the construction joints.

iii) Supply and Applying injection grouting through the nozzles grouting pumps with a minimum pressure of 2 kg/sqcm with cement slurry admixed with CICO Non shrink Polymeric Water Proof Grouting Compound or approved equivalent at the rate of 2% by weight of cement.

iv) Sealing & cutting of the nozzles, and leveling the surface using integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Supplying and painting of 2 coats plastic emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. The rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Providing and laying of Rubber Moulded Hydraulic Pressed Paver Block -63mm thickwith C.M 1:3 pointing over Sand filling bed compacting, sand brushing and cutting, levelling, transporting etc., complete with the natural grey colour blocks, as directed by the Departmental Officers.

Providing and laying of Rubber Moulded Hydraulic Pressed Hexgon Paver Block 400x400x63 mm thick with C.M 1:3 pointing over Sand filling bed compacting, sand brushing and cutting, levelling, transporting etc., complete with the natural grey colour blocks, as directed by the Departmental Officers.

Providing And Laying Mastic Asphalt 25 mm Compacted Thick Using 13.2 mm Irc Metal Quarry Dust Lime (Shell Lime) With 80 Kg of VG40 Grade Bitumen Including Cost And Conveyance of All Materials To Site Including Labour Charges Etc. And Including Hire Charges And Fuel Charges For Machineries And All Other Tools And Plants Required Including All Other Incidental Charges Etc. Complete As Per Specification Clause 515 of Mort & H

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And All Taxes Including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining Etc Complete .

Mural Fibre Work – reflecting the cultural richness of the region on top of the wall all around as per architectural drawing in-engineer-in charge

Supplying and fixing B.R.C. weld mesh partion without teek wood frames including fixing in position in the existing frames with teek wood filx ,etc,complete.The size of weld mesh will be (75x25mm)

Supply and fixing of ploycarbonate sheet 6mm thick as per architectural drawing.

Providing, applying and finishing the top surface of concrete with stamped of approved pattern as per architectural drawing

Dadooing wall tile size of 300x450x8 mm with following best approved quality, Designed colour ceramic tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Providing anti-skidCeramic tiles of size 305 x 305 x 6mm flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Finishing the top of roof with one course of machine pressed tiles of size 23x23x2cm of approved quality laid in CM 1:3 (one cement and three sand) mixed with 2% of water proofing compound by weight of cement used and pointed with the same oiled mortar including mixing of red oxide etc complete complying with standard specifications and as directed by Departmental Officers

Weathering course-using Concrete broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers.

providing and laying precast saucer type drain of size 600x300 x 50mm with M30 GRADE concrete including the Cutting of the existing bituminous surface of 10 cm thicckness and PCC of 1:3:6 for leveling and maintain the gradient to drain the water from raod to Storm water Drain etc and complete

Providing and fixing 20mm thick Granite - (Superfine Polished with Machine CutEdges) for PLATFORMS, seating top finished copping, etc., of approved quality for wash basin/ vanity counters,pantry etc. of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 Cement:4 M Sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by Engineer-in-Charge.

Supplying and fixing Brazilian IPE wood – walkway decking, IPE wood plank dimension – 65mm -115mm (90mm) width x 19mm (+\- 1mm) thick random length 1000 -2000 mm. Fixing the decking including labor charges, L cleat or SS screws and necessary treatment as per standards,anti termite protection and oil coating. cost including grooves, labour, transportation , etc. complete. FFL of decking to be flushed with sand level as per architect's specifications.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supply and fixing of Rough Granite stone seating in 2 ft height and finishes as per architectural drawing .

Supply and Fixing of FRP LION statue in 5ft ,The LION statue from India are extermely strong and Durable. Lion Statue can be dropped and put through stress and not breakable.The statueas per Architectural drawing (

Supply and Fixing of FRP Elephant statue in 8ft ,The Elephant statue from India are extermely strong and Durable. Elephant Statue can be dropped and put through stress and not breakable.The statueas per Architectural drawing (

Supply and Fixing of FRP Elephant statue in 4 ft ,The Elephant statue from India are extermely strong and Durable. Elephant Statue can be dropped and put through stress and not breakable.The statueas per Architectural drawing (

Supply and Fixing of FRP Giraffe statue in 8 ft ,The Giraffe statue from India are extermely strong and Durable. Giraffe Statue can be dropped and put through stress and not breakable.The statueas per Architectural drawing (

Supply and Fixing of FRP Deer statue in 8 ft ,The Deer statue from India are extermely strong and Durable. Deer Statue can be dropped and put through stress and not breakable.The statueas per Architectural drawing (

Play Equipment

Supply and fixing of FRP SWING (Single swing with belt Assembly) Swing 1 Seaters Frame made of 2 inch Stainless Steel pipe and 1 ½ inch supporting pipe Height 7 ft and breadth 5ft. Seats made of FRP moulded materials with heavy duty chain.

Supply and fixing of Kiddies Fun Station Height:141/2’, product size:22’*70’, lader:1 ¼” GI pipe,3/4”GI pipe, 2.5mm thickness,B class,leg:21/2” GI pipe,2.5mm thick,B class,railing:1”&1/2” GI pipe, 2.5mm thick, B class, bed:1 ¼” GI pipe, 2.5mm thick,B class, Roller slide:2”angle,1” GI pipe, 2.5mm thick, B class, square climber:1”&3/4”GI pipe, 2.5mm thick, B class, rope climber:1 ¼” GI pipe, 2.5mm thick, B class, FRP tunnel size:3’, twin slide:9’, paint: pu coating

Supply and fixing of See-Saw 4 Seater FRP: Height :1 ½ ‘ft Width :5’ft Frame : 1 ½” Galvanished ‘B’ Class pipe See saw Rail :2” Galvanished ‘C’ Class pipe Seat : FRP Seat with 450 CSM Mat 3 Layers bonding. Seat : FRP Seat with 450 CSM Mat 3 Layers bonding. Isotolic gel coat with UV pigment. Painting with PU coating seat size : 15”ft * 14”ft Productarea : 5’ft * 10’ft Play area:8’ft * 12’ft

Supply and fixing of Merry go round – 6 Seater (FRP) Height :3” GI Pipe, 2.5mm thick, b class Seat size:15” X 14”, paint: pu coating

Supply and fixing of Double Bar / Parallel Bar Frame:1/2”GI pipe, 2.5mm thick, B class, height:41/2’, product size:6’*2’ paint: pu coating

Supply and fixing of SIT UP & PUSH UP BENCH (SINGLE) Abdominal muscles, upper Leg muscle and Back muscle exercise. Also strengthens Arm Shoulders muscles. Size: 1650 x 750 x 1400mm – 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life.

Supplying and fixing of Flat Bench: IFFB of Tubing thickness of 2.5 mm and the functional parts with rectangular tube at size of 50 x 100 x 2.5 mm ,Pad total thickness is 70mm ,Designed with stainless steel seat adjustment that provides a longer service life, made it easy to adjust and look beautiful. Dimension: 1305 L x 525 W x 493 H (mm) ,Product Weight: 19.5 kg / 43 lbs Warranty: 1 Year

Supply and fixing of ARM AND LEG STRENGTHENER leg and Arms muscle exercise. Strengthen joint and cardiovascular system. 1435 x 740 x 1005mm) 4mm Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes. Thick Rexin covered cushioned Seat & Back rest Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life

Supply and fixing of TWISTER & LEG TRAINER Back and spinal joint exercise. Strengthens abdominal and spinal. Also increase Flexibility of upper and lower 49and spinal. Also increase Flexibility of upper and lower back. Size 1700 x 510 x1425mm) 4 mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Thick Rexin covered Cushioned Seat. Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life Supply and fixing of TWISTER & LEG TRAINER Back and spinal joint exercise. Strengthens abdominal and spinal. Also increase Flexibility of upper and lower back. Size 1700 x 510 x1425mm) 4 mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Thick Rexin covered Cushioned Seat. Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life

Supply and fixing of ARM & SHOULDER WHEEL Supply, Erection and Fixing of Arm & Shoulder Wheels 1300 x 1200 x1350 mm 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life.

Supply and fixing of DOUBLE CROSS WALKER Cardio, lower/upper body exercise. Main Post made of 4 Inch Pipe an other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes (1680 x 515 x 1780 mm) 4 mm pipe Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life. Steel Foot rest / Foot Paddle for long lasting life.

Boxing ring 24’ x 24’ is made by six tables 12’ x 8’ A)Boxing ring 24’ x 24’ is made by six tables 12’ x 8’ having the following details 1.Size 24ft x 24 ft from corner poles i.e. total area 2.Size 20ft x 20 ft from rope to rope i.e. playing area. 3.Height of ring is 1 mt. from ground level 4. Four ropes 3.5” thick covered with synthetic in white, blue and red color or P.V.C. white pipe 5. Corner poles made of 4” pipe in white, blue and red color. 6.Laminated waterproof wooden planks of 8’ x 3’ and 8’ x 4’ are used on the top of six tables. These planks make level of the floor equal & nice. 7.Total wooden floor is covered with 3/4 “ (E.P.) Expended polythene foam. Then this foam is covered with waterproof canvas cover. 8. Four protection corner padding are used to cover corner poles to protect injury to player 9 . All four corner poles are attached with cross link tensioned wires with coupling tighter with each other diagonally.

Reinforced Cement Concrete Bollards with M20 grade concrete and 150mm dia 4 Nos of 10mm dia TMT of overall size 800mm, 100mm projection of TMT Roads at the bottom of the Bollards beyond 800mm for anchor. Black pigment at 4.5 percent weight to cement will be used. Two Strips of Reflective 3M Sticker of width 40mm, including transportation and fixing charges etc, complete

Conveyance of Earth/Debris to a lead of within 30 km from site as directed by the Engineer inculding loading, unloading, hire charges for vehicle and other incidental charges etc., all complete as directed by the Departmental Officers.

Joinery

Providing of 35mm thick factory made pre - laminated ABS ( Acrolynitrile Butadiene Styrene) Door Shutter moulded indifferent desings consisting of all round frame made out of water proof solid PVC bar of size 20 X 32 mm reinforced by 32 X 32 mm 2 nos ., for vertical made out of LVL core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with pre- laminated ABS sheets thickness of 1.5mm PVC edge bending of size 0.45mm on the vertical sides. hardware made out of steels coated butterfly hinges - 3nos for each shutter and ISI make SS round lock Complete complying with the standadrd Specification . the door shutter and frame should be got approved from the Departmental Engineer before on use

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

PLUMBING

Supply of 2000 ltrs PVC Sintex water tank including cost of materials

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing the best quality approved make of bib cock with cp health faucet wall hook 1m long flexible tube angle cock with wall flange incuding cutting and making the walls whereever etc, complete complying with standard specifications and as directed by the departmental officer the quality and make of health faucet should be got approved by concerned department engineer before use of work.

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Supplying and fixing in position Mirror of size 500x450mm of approved quality and brand of size with necessary plastic back PVC frame with bottom stand of approved color with brass screws rowel plugs etc complete complying with standard specification and as directed by the Departmental officers The quality of mirror should be got approved by the Executive Engineer before use on work

Wash Hand Basin of size 550 mm X 400 mm without pedastal with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. The quality and make of below counter Wash basin should be got approved by department Engineer before use on work.

Lipped Mouth Porcelain white Flat Back Urinal with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc.e Engineer-in-Charge.

Supplying, installing, testing and commissioning of approved make full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tested to a pressure not less than 20 Kg / sqcm with threaded joints complete.

Cost of 25mm dia U.P.V.C Ball Valve

Cost of 32mm dia U.P.V.C Ball Valve

Cost of 40mm dia U.P.V.C Ball Valve

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to ISS and with ISI mark of the following size including cutting, threading and fixing PVC specials but excluding cost of such specials and fixing to wall with necessary teak wood plugs, PVC clamps and screws, making good the portions to original condition with necessary brick work and concrete plastering wherever necessary with necessary scaffolding charges etc. complete complying with standard specification and as directed by the Department officers. The quality and make of UPVC pipes and specials should be got approved by Concern department Engineer before use on work.

Main data 32 mm dia UPVC pipe

Main data 40 mm dia UPVC pipe

Providing enamel indication board with proper male or female figure of size 35x30cm as directed.

Supply of Compactor Bin 1100 litres made of galvanized Sheet, thickness of 2.5 mm, side and bottom 3 mm , MS angle and MS channel and 8" heavy duty fibre wheel as directed by the department officers. The cost includes the labour charges, transportations all complete as per Engineer in Charge

Supply of Penguin dustbin FRP – 2 Layers to a height of 3½ and width of 2½

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Supplying & fixing in position C.I.Nahini trap of various sizes with best stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes as directed etc., complete, complying with standard specification (The C.I.Nahini trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing in position the best quality and variety sizes PVC soil waste pipes 6Kg cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the portions. The quality and make of PVC pipes and specials should be got approved by Concern department Engineer before use on work..

110mm Dia

Supplying & fixing of SFRC Manhole cover of size 600mmx600mm complete and as directed by the departmental officers..

Construction of inspection chambers of following sizes 60 x 60 x 150cm with earth work excavation for foundation with 23cm thick brick jelly cement concrete bed in C.M.1:4:10 using 40mm Brick jelly for foundation, brick work in C.M. 1:6 for chambers, plastering with C.M.1:3 12mm thick, benching, channelling, 75mm thick RCC loose slab covering in C.M.1:2:4 mix using 20mm blue granite jelly including necessary reinforcement, etc.

Supply and Fixing of Gun Metal Gate valve 20mm dia. The rate including labour charges for fixing and cost of materialsetc. Complete.,

Supply and fixing of 30 meter in length PVC braided water Garden hose is extremely pressure-resistant and keep its shape, durable resistant materials as per Engineer in Charge. The rate inclusive of necessary fittings and Transport charges .

Supply and erection of 2.Hp Submersible Pump set using nylon rope including cost of motor , fixing necessary cable charges and labour charges etc., complete

Supply and erection of 3.Hp Submersible Pump set using nylon rope including cost of motor , fixing necessary cable charges and labour charges etc., complete

Landscape work

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller.

Planting of Dracena marginata ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Caesalpinia pulcherrima foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Sabal palmetto variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height,including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying and Planting of Raphis palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height,including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Phoenix dactylifera palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height,including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Heliconium foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Galphimia Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of pinus thunbergii tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of coconut tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of borassus flabellifer palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height,including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Maintenance of garden for a period of six months including all required materials and man power etc., all inclusive.

Cvill work in Electrical

Construction of inspection chambers of following sizes 60 x 60 x 90cm with earth work excavation for foundation, 23cm thick concrete bed using 40mm brick jelly concrete in C.M.1:4:10 for foundation, brick work in C.M.1:6 for chamber, plastering with C.M.1:3, 12mm thick, benching, channelling, supplying and fixing 45x45cm FRC cover and frame, etc.

Electrical work

TNEB METERING BOARD Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete the work etc.

200A Isolator Switch- Supply and fixing of 200A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with PWD earthing.

Design, supply, fixing, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Incoming 1 No: 200A 4P 35KA MCCB (Incoming EB source) 1 No: 200A3ph 4 pole Change Over Switch 1 No: 125A Four Pole MCCB (DG Incoming) Incomers shall have 1 set - Digital Combined meter (Having the parameters of Ammeter,Voltmeter and KWH meter). 1 set - LED type RYB,ON,OFF,TRIP indication lamps. Panel mounted Earth Leakage Relay with Leakage current display. 1 set -250 /5A CT CL 1.0 10VA. Outgoings: 12 Nos - 63 A 16KA TPN MCCB. 2 Nos - Multifunction Meter digital type / MFM 5010 LED meter CI 0.5S with RS485. Note : All the Outgoing feeder shall be having 'on',off,trip' indication lamps..All switch boards shall be fabricated as per the detailed specification enclosed. Suitable size outgoing cable chamber and extra busbars should be provided for connecting the number of outgoing cables as per the schematic drawing. The board shall be fabricated for future extension of the panel board. Note:-The panel should be having provision to monitor the On, Off, trip status. BUS BAR RATING: 200A TPN 16 KA for 1 sec. Aluminium bus bars (Current Density not less than 0.8A/Sq.mm.) with colour coated heat shrinkable PVC sleeves with DMC/SMC bus bar supports and suitable earth bus. Earthing : 25 x 6mm Aluminium flat . Cable Entry & Exit : Top. Cable Gland Plate : 3mm thick MS sheets Note: All MCCBs shall have rotary handle mechanism and spreader wherever necessary.

Supply, Erection, Testing and Commissioning of the following Type Outdoor lighting distribution panel with individual segegration chamber with MCCBs / MCBs /ELCBs, / RCCBs , Phase segegration Timer and contactor manufacturer's sheet 16SWG enclosure for with provision for cable entry boxes, with Outdoor application IP65 as specified Protection, fixed on the floor with all interconnections and accessories, pedestal frame with concrete grouting or suitable to fix at concrete plinth as per the Corporation/ Highway department requirement. Incomer 40 A TPN MCB with Timer control On/OFF Outgoing : 20 A DP RCCB -30mA - 12 Nos.

Supply and fixing of 7 segment 8 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 8 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. (Without ELCB)

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal) with 1 no.63A 4P MCCB switch as incoming and 8 nos.32A 3P MCB , as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End

Cables

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

Supply and Laying of 3 1/2 x 95 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 35sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 31/2C x 25 sq.mm Al XLPE armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 4C x 10 sq.mm Al XLPE armoured LTUG cable in size of 38/50mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 4C x 6 sq.mm Al XLPE armoured LTUG cable in size of 38/50mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of following XLPE armoured LTUG cable on post or on wall MS-Clamps , Saddles, plugs, Screws etc., as required.

Supply and Clamping of 3 1/2 core x 95 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 4C x 16 Sq.mm PVC armoured LTUG aluminium cable on post or on wall with MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and laying of 4C x 10 sq.mm Al XLPE armoured LTUG cable in size of 38/50mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 4C x 6 sq.mm Al XLPE armoured LTUG cable in size of 38/50mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

GLAND

Supply and fixing of brass cable gland for 3 1/2 C x 95 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 35 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 25 Sq.mm PVC LTUG armoured cable with earth connection.

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 10 sqmm COPPER cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 6 sqmm COPPER cable LTUG cable with earth connection.

TERMINATION

Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Supply and providing cable end termination of 3 1/2 Core x 95 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 35Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 25Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 4C X 10 Sqmm PVC LTUG Aluminium cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4C X 6 Sqmm PVC LTUG Aluminium cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Internal Electrification

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with Module GI Switch Box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light / Fan Point (for electronic) (Primary Point )

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with Module GI Switch Box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light / Fan Point (for electronic) (Secondary Point )

Run of Mains

Supply and run of 2 of 2.5 sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection 1 of 2.5 sqmm (36 /0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed wall and ceiling with continuous earth wire connection 1 of 2.5 sqmm (36 /0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade and making good of the concealed portion with suitable colour.

Supply and run of 50mm Dia HDPE pipe of 4kgf/cm2 approved quality and best variety conforming to ISS and ISI mark below ground in HDPE pipes.

Pole and fittings

Solar Street Light: Supply and fixing of 65mm dia GI pipe (Class 'B') of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom and with concreting and construction on masonry pedestal with supply and fixing of 50 watts LED Light IP 66 degree of protection , Integrated mono crystalline solar panel , lithium phosphate battery and high efficiency high power LEDs with secondary optics offering precise distribution control . The luminary should be with PIR motion detectors to extend the battery life during non- peak hours of operation. The entire assembly should be in aluminum extruded body and should act as better heat sink for better operation of and life of the luminary. The GI pipe should be painted with suitable colour and commission in full as per the directions of the concerned authority of Cycle path area. The price is exclusive of GST.

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED Street Light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 10A SP MCB , 2/4way connector on suitable hylem sheet and with supply and fixing of 150W Flood LED light Complete with suitable MS Brackets for 150W LED Flood light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

Supply, Installation, Testing & Commissioning of 40W LED LANDSCAPE Gate Light Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminum heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection. Decorative post top with 3 mtr height pole for 360 degree Indirect light with IP 65 protection, Resistant to impact and corrosion. Glare-free and better uniformity. MAPLE LPTO-40-CDL/M make :Crompton Features and details Aesthetically designed and soft illumination effectumens : 2450 lm power : 40W colour : multi colour Included components : post Top Rate shall inclusive of necessary joint kit,glands,etc for loop in/out connection suitable to outdoor application. Crompton CAT REF : - LPTO-40-WW-M Equivalent.

Supply, Installation, Testing & Commissioning of 10W LED bollard light fittings Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminium heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection. The driver should be Constant voltage constant current SMPS Protection of Fitting should be IP 66. LED having 50,000 burning hours with minimum 70% lumen maintenance and power factor 0.95. System consumption should be require with lumen package as per requirement. Crompton CAT REF : - LBLA3-10-CDL / Equivalent-(LANDSCAPE LIGHT). rate shall inclusive of necessary joint kit, glands, etc., for loop in/out connection suitable to outdoor application.

Supply and fixing of Sudo Asy Frame 12W LED Light fitting with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of Floor mount Foot Lamp 3W LED Light fitting (IP67) (Step Lighting ) fixture with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of Spike light 6W fitting on floor with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work. KL-Trioscope - 7052.

Supply, installation, testing and commissioning of 36W LED Surface Mounted (2x2) LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the neary by point with 1.5 sqmm FRLS PVC insulated copper wires including ncessary accessories and harwares as required.

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 meter rod with fan clamp with side plates and cross arm of size 450mm(18")

Supply and fixing of louvers shutters arrangements for 300mm(12") sweep (light duty) AC exhaust fan,including ncessary accessories and harwares as required.

Supply and fixing of 1 no.16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

Supply and fixing of 1 no.6A two module 5pin socket, 1 no. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3nos.6/16 A two module 5 pin socket , 3 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD-500)

Supply and fixing of thermoplastic loop - in and loop out boxes with lid of dimension min 104X104X70MM with 20A connector. shorting link 2 way necessary and along DIN rail terminal block. The Junction Box shall be insulated and made out of high grade thermoplastic. The JB shall be IP Rated for outdoor applications, environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid& anti corrosive. The JB shall be rated for Degree of Ingress Protection IP 65 in accordance with IEC 60529.

Earthing

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 25mm x 6.25mm Aluminium flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8SWG GI wire at the equal interval of 1.5 meter and etc to complete the work.

Coil Earth to Street light poles with No 8 SWG GI wire of 11.5 Mtrs of length in which 10 mtrs of total length compressed in to a coil of one meter length (75 mm to 100 mm dia) connected suitable with Hexagonel earth bolt of size 8mm to 25 mm welded on the pole at one end with a coil position fixed on the earth and etc to complete the work.

CCTV SYSTEM

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 6TB Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony).

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behaviour analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic

Supply, Installation, Testing and Commissioning of 42" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote (Make: Sony/ LG /Samsung).

Supply and fixing of outdoor 4X6 PVC box with 102mm x 77mm x 102mm with all fixing accessories

Supply and Laying of CAT 6 armoured cable in 50mm HDPE pipe below the ground complete with all necessary accessories etc.. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack SinglePoint (Point to Point) Crimping, Testing and arrangement charges.

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.(Make: DLINK,NETGEAR/TPLINK)

Supply and fixing of Out Door Weather Proof Box 2Ft x 2Ft Out Door Weather Proof Box 2Ft x 2Ft with necessary accessories etc.,(For PoE Switch)

Supply and Fixing of Rack with Accessories -Higher end 36 U Rack with LNS unit and fan extra for the above rack.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Erection of 6m Length pole with base plate of size 250x250x6mm as per IS-875 with following specification. Pole Outer die -76.10mm x 3.65mm Thick x 6 meter.

PA SYSTEM

Supply, Installation,Testing & commisioning of 480 watts P.A Mixer Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent).

Supply of 10" gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedence and has 2.5mv/pa sensitivity and frequency response ranging from 50-15000hz with multi tone chime model.(Make:-ACM66 Ahuja/bosch/its equivalent)

Supply and Run of 2Core x 1.5sq sqmm PVC insulated Armoured Speaker Cable in suitable 19mm dia Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply & Installation of custom built M.S Powder coated wall mounting Audio rack with Lock & key for housing of Amplifier & Player / Recorder conforms to EIA-310,IEC-60297 and able to withstand the load of 40kg with welded construction made up of CRCA steel with suitable height, width and depth.

SAFETY ACCESSORIES

First Aid Box complete with all First Aid Medicines

Danger Board as required by the Electrical Authorities

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT /SAFETY FIRST / EQUIVALEN

Sri Sivaram and co

N.S.PERIASAMY AND CO