Construction of a public toilet in the vending zone near the stadium in Hamirpur Municipal Council.

Boring of 30cm dia piles of single under reamed of 50cm dia of bulb and 3.5 meter depth in black cotton soil with hand operated auger machine including all laboure T&P etc. for proper completion of work as per IS code-2911(Part-III) 1980.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:(All kinds of soil) As per DSR-2.1.1

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.As per DSR-2.27

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).As per DSR-4.1.8

Providing and injecting chemical emulsion for pre-constructional antitermite treatment and creating and chamical bariier under and arround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981) approved material such as Hepthachlor or chlordane will be used. The rate of application of chemical emulsion shall be as follows.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) :.As per DSR-5.2.2

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth Cement morter 1:4 .As DSR NO.- 6.1.1

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in Superstrecture and above plinth Cement morter 1:6 .As DSR NO.- 6.4.2

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars.As per DSR-5.22.1

CEMENT PLASTER (IN FINE SAND)12 mm cement plaster of mix :in 1:4 (1 cement: 4 fine sand).AS per DSR No.- 13.1.1

4 cm thick cement concrete floor 1:2:4 finished with a floating coat of neat cement including cement slurry,but excluding cost of nosing of steps etc all complete.As per DSR no.- 11.3.1

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Glazed vitrified floor tile polished finish of size of tile 600 x 1200 mm .As per DSR No.- 11.41A.2.2

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

supply & Fixing of 10cm Internal dia PVC pipes complete with rose- heads, bends abd gratings & including supply of necessary M.S. clamps 2.5cmx3mm (1"x1/8") fixed to walls, with & including supply of 15cm (6") long 6mm (1?4") dia nails & including supply of all materials, labour and T&P etc required for proper completion of the work and also including repair of plaster, pointing etc if damaged during fixing of pipes, details of 30' length.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.As Per DSR No.8.2.2.1

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.As per DSR No.- 10.1

Supply & fixing of flush doors commercial quality conforming to IS 2202 Part 1 (1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts locks handles springs fitting with necessary screws to be supplied departmentally. (a) Single leaf (35 mm Thick). As per DSR No. - 9.20.1

Painting or varnishing new iron work in small areas of new wood of 1 sqm area with one coat of ready mixed priming paint and two coat or approved superior quality ready mixed paint or varnish including supply of all material, labour and T&P etc. required .AS per SOR

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. As per DSR No.-17.1.1

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid As per DSR No.-17.3.1

White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI Marked. As per DSR No.- 17.7.9

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(25 mm nominal dia Pipes).Asper DSR No.-18.7.3

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(15 mm nominal dia Pipes).Asper DSR No.-18.7.1

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore. As per DSR No.- 18.17.1

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.As per DSR No.- 18.51.1

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.As per DSR No.- 18.52.1

Supply & wiring of sub-main with 2 nos 2.5 sqm FR P.V.C. insulated 1100 volts grade multistand single core copper conductor cable in 20 mm diameter heavy duty 2mm thick P V C conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete .As per E&M DSR no.- 1.14.2

Supply & wiring of sub-main with 2 nos 4 sqm FR P.V.C. insulated 1100 volts grade multistand single core copper conductor cable in 20 mm diameter heavy duty 2mm thick P V C conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete .As per E&M DSR no.- 1.14.2

Supply and erection of AC 230/250 Volts 50 Hz Exhaust fan including providing nuts bolts amounting frame & other accessories including connection etc. complete as required (Crompton Greaves/ GEC / Orient or equivalevt mark)(a) - 300 mm Sweep As per market

Supply and erection of AC 230/250 Volts 50 Hz Cilling fan including providing nuts bolts amounting frame & other accessories including connection etc. complete as required (Crompton Greaves/ GEC / Orient or equivalevt mark)(a) - 1200 mm Sweep As per market

Wiring point for light /fan /exhaust fan with 1.5 sq.mm FR P.V.C insulated multistrand single core copper cunductor cable in P V C cond-uit pipe part cocealed in wall & partly laid in slabalong with the reinforcement before concreting complete with 14 S.W.G. copper earth continuity wire & piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc. complete in all respect.including matching color wash.As per DSR no.-1.1.1

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. CAT- AAA

Supply & fixing of 5/6/7.5/10/15/20/25/30/32 Amp SPMCB 9 KA/10 KA

Supply and fixing of flush/surface mounting distribution boards without MCB with additional metal door complete in all respects.(CAT:B)8 Way SPN

Supply fixing and making connection of following FPMCBS complete in all respects as per direction and satisfaction of engineer- in-charge.40 Amp. DP MCB

Supply and burying of 40mm dia x 4.5meters long G.I. pipe, vertically for earthing having 12 mm dia. Holes spaced 75mm apart drilled upto 2 meters from the bottom complete with earthing lead of no 6 to 8 SWG GI wire in GI pipe upto appron (and from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I. box with hinged cover, masonary enclosue, funnel at top, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 2500 m as per Technical specification clause 301.5

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.DSR No. - 8.32

Casement window single panel with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. Using R4 series with frame (64 mm & above) x (50 mm & above) & sash (64 mm & above) x (70 mm & above). (Height above 1.8 metre).As per DSR No.- 9.147.E1.3

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.As per DSR No.- 17.16 A

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.As per DSR No.- 17.22

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. DSR No.- 17.22A

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. DSR No.- 17.24

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing..As per DSR No.- 12.52.4

Providing and fixing Piller cock 15 mm dia TALL HEIGHT i/c all cost of material t&p etc all complete.(As per GEM)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.As per DSR- 18.48

Providing & fixing 3D Acrylic sheet letter With lighting including fitting i/c all cost of material labour T & P etc all complete.(As per market)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable methodprescribed in IS: 2800 (part I), including collecting samples from different strata,preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. DSR - 23.1.1.1

Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized 150 mm dia PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.DSR - 23.3.2

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.DSR - 23.6

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. DSR 23.12

3 HP 9 Stage Submersible Pump of ISI mark With automatic panel.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). DSR - 10.28

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mmDSR - 17.32.4

Supply and fixing of bright led aluminum profiles chenal with LED Strip light i/c all cost of material, labour T&P etc all complete. (As per market rate)

Please Enable Macros to View BoQ information