SPECIAL REPAIRS TO EQUESTRAIN T31 32 AND 33 AND ASSOCIATED SERVICES STRUCTURE AT SITE III OF INS TRATA UNDER GE NW KUNJALI COLABA MUMBAI

Amount

Taking down chowkat with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each

Taking down chowkat with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4 Sqm each.

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc upto third floor of Bldg including necessary formwork and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor.

Material & labour for brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and as directed.

Material & labour for brick work with sub class 'B' bricks , straight or curved on plan to any radius in half brick thick wall built in cm 1:4.

Material & labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat using polymer modified ready mixed cement based plaster having minimum composition of cement & sand (1:4) using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces including using richer mix for making corners if necessary including making grooves of existing size and necessary two legged MS pipe scaffolding wherever required including curing,upto ground plus 3rd floor bldg complete all as specified and directed.

Material & labour for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing the surface fair and even complete all as specified and directed.

Material & labour for rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in ceiling and finished even and smooth without using extra cement complete all as specified.

Material & labour for preparing new plastered surfaces of wall, applying one coat of wall care putty not less than 3mm thickness and making the surface even and smooth using emery paper and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified.

Material & labour for prepration of new plastered wall surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of Plastic emulsion paint interior grade over a coat of primer complete all as specified and directed.

Material & labour for preparation of surfaces of walls, chajjas, parapets,ceiling etc including removing loose materials from cracked surfaces and filling the crack with crack filling compound of approved grade and applying one coat of weather proof acrylic exterior paint (100% Acrylic) including necessary scaffolding and safety arrangement upto three storey buildings complete all as specified .

Material and labour for complete removal of existing treatment including washing, rubbing down and stopping of distempered and painted wall surfaces, filling holes and cracks with filling putty and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified..

Material & labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and directed

Material & labour for preparing old decorated surfaces of walls, soffitSupply & fixingacias of beams, chajjas etc including washing, rubbing down & stopping & and applying two coats of weather proof acrylic exterior paint (100% Acrylic) including necessary scaffolding and safety arrangement complete all as specified .

Supply only integral water proofing compound.

Supply & fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & manufacturers instructions.

Supply & fixing 30 mm thick factory made solid panel PVC door shutter (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & manufacturers instructions.

Supply & fixing powder coated aluminium sections (minimum thickness of powder coating 50 micron) for partitions, windows, ventilators and doors including fabrication of frame/shutters and fixing to walls/floors with necessary lugs, cleats etc including all accessories such as cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, glazing clips, and rubber beadings for fixing glass panes in frame including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM,rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required complete all as specified Note: - (i) Glass panes will be measured & paid separately. (ii) Rubber beading will not be weighed and paid separately

Supply & fixing Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, Area exceeding 2.00 sqm each. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.

Material & Labour for aluminium anodized grill DG -104 made out of aluminium sections of weight not less than 2.453 Kg/ Sqm and tensile strength 19 Kg/Sqmm with suitable aluminium anodized frame of F/H section with suitable fixing screws/attachment etc complete all as per manufacturer's specifications.

Supply & fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple complete all as specified.

Supply & fixing 6.3 mm thick, Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane in door shutters, partitions, shelves etc complete all as specified .

Supply & fixing 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts , ISI marked complete all as specified.

Supply & fixing 200 mm aluminium anodized barrel tower bolts of extruded section and fixed , ISI marked complete all as specified.

Supply & fixing 150 mm aluminium anodized barrel tower bolts of extruded section and fixed , ISI marked complete all as specified.

Supply & fixing 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified.

Supply & fixing 100 mm Stainless steel butt hinges medium weight with SS hinge pin , bright finished.

Material & labour for rolled mild steel in Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections including all necessory drilling, bolting,riveting or welding conforming to Fe 410 -W (Gde-E- 250) quality-B complete all as specified and directed by Engineer-In-Charge.

Supply & fixing mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, without any attachment including all necessory drilling, bolting,riveting or welding conforming to FE 410-W, (Gde- E-250) quality-A complete all as specified.

Material & labour for rolled mild steel in stairs (framed) including stringers, treades, landing, balusters, hand rails etc including cleats, brackets etc including all necessory drilling, bolting,riveting or welding conforming to Fe-290 (Gde E-165) complete all as specified.

Excavation in post holes (or similar holes) each n.exc 0.5 cum getting out in hard/dense soil, returning filling in, and ramming earth or broken rubble mixed with earth around in layers n.exc. 25 cm and removing surplus soil to a distance n.exc 50m and making good disturbed surfaces as per existing complete all as directed.

Roughening surfaces of old cement concrete floor by picking, sweeping, cleaning and washing down with water to remove dust etc complete all as specified.

Material & labour for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primesed completed all as specifed and directed Note: The place of disposal shall be find out by the contractor.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including removal of rubbish out side MD land. Note: The place of disposal shall be find out by the contractor.

Material & labour for 40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate ) as in floor finished even and fair complete all as specified and directed.

Material & labour for 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate ) as in floor finished even and fair complete all as specified and directed.

Material & Labour for Non skid coloured ceramic tiles 7 to 8 mm thick (square/Rectanglar) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floor laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour for coloured glazed ceramic tiles 450mm x 300mm x 7mm thick but laid on vertical surfaces such as skirting/dado laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour 10mm thick double charged vitrified ceramic tiles, premium quality of approved colour (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors laid over and including 20mm thick screed bed or bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour 10mm thick double charged vitrified ceramic tiles, premium quality of approved colour (square/rectangular) polished, area of each tiles not exceeding 0.36sqm (600x600mm), as in vertical surfaces such as skirting/dado etc., laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour for 20 mm thick machine cut Granite slab as in steps/stairs, window- cills, cooking platforms, working table and like laid over and including 15 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and grinding, polishing complete all as specified and directed by Engr-in-Charge .

Material & labour for 20 mm thick maching cut granite slab as in vertical surfaces such as skirting/dado, jambs, pillars, etc laid over and including 10mm thick backing coat in CM (1:3) and set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of granite stone including grinding, polishing complete all as specified and directed.

Material & Labour for 18-20mm thick, machine cut, Kota stone slab, as in floors, steps, landing etc. laid over and including 20mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including rubbing, cutting and polishing as specified in SSR Part I complete all as specified.

M &L for machine cut kota stone slab 18 to 20 mm thick as in vertical surfaces such as skirting/dado laid over and including 15mm thick backing coat in CM (1:4), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile including rubbing, cutting and polishing as specified in SSR Part I complete all as specified.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and other similar situations

Excavating in trenches n exc 1.5m wide & n exc 1.5m in depth; for foundation, etc. or for manholes n.exc.10 Sqm on plan and n.exc.1.5m in depth and getting out in hard/dense soil completes all as specified.

Material & labour for PCC 1:4:8 type D2 using (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point.

Returning filling in , including spreading, leveling, watering and well ramming in layers not exc 25 cm.

Material & labour for RCC M:20 grade (using 20 mm ground stone aggregate) in foundations, including rafts, footings etc and mass concrete complete all as specified.

Material & labour for RCC M:20 grade (using 20 mm graded stone aggregate) in columns, pillars, piers, posts and struts.

Material & labour for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams etc, vertical or to batter for rough finished surfaces of concrete flat.

Material & labour for form work to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete flat.

Material & labour for TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with the clips complete all as specified .

Ditto- all as per item No 57.00 above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders.

Material & labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in copings, lintel, bands etc including weathering slightly rounded or chamfered angles and throating and form work complete all as specified.

Material and labour for Cement concrete work (PQC) ready mix concrete in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less including use and waste of side form for laying pavement concrete/hard-standing in bays between joints & Contraction expansion joint/or between the two contraction joints complete all as specified and directed

Material & labour for 15mm thick Wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) complete all as specified and directed

Supply only Metallic floor hardener complete all as specified and directed by Engr-in-charge

Material & labour for MS framed work such as gates,, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings etc with ornamental and intricate design conforming to Fe.290.Gde-E-165 complete all as specified

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal of debris out of MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Material & labour for hardcore of broken stone or boulders of gauge n. exc 63mm, deposited, spread and leveled in layers n. exc 15cm thick watered and rammed to true surface complete all as specified.

Material and labour for 150mm thick PCC 1:2:4 type B2 ( using 40mm graded stone aggregate) as in floor & finishing even and smooth without using extra cement including necessary formwork complete all as specified and directed.

Material and labour for 50mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection & finishing even and smooth without using extra cement including hacking out exsting concrete surface complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge or thickness including Nainital or similar pattern roof coverings all as specified and directed.

Supply & fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, fixed with self tapping screws complete all as specified.

Supply & fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws complete all as specified and directed.

Material & labour for rolled mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt elded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed .

Supply & fixing in repairs galvanised mild steel sheet eaves gutters made out of 1 mm thick galvanised class 3 sheet 100 mm dia, , half round with rounded edges complete all as specified and drected.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets of any thickness including cover fillets complete all as directed.

Material & labour for false ceiling made out of 600 x 600 x 6 mm thick ceiling board/tiles deep panel suspensor system made out of powder coated GI sheet main tee of size 23.50 x 40 x 0.63 mm and cross tee of size 23.50x23.50x0.63 mm and angle size 19x19x0.63 mm including 3 mm GI wire for suspending bolts necessary washers nut/cleats/pin hook etc for securing frame work to ceiling to the snap grid including provn of necessary holes/cutting for providing light/far as required including making necessary recesses/projected pattern complete all as spoecified and as directed.

Material & labour for POP false ceiling using 600 x 900 x 12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work main joist of size 50 x 25 mm spaced at 750 mm centre, secondary joist of size 75x20 mm fixed to main joists spaced t 900 mm suspended to roof members using 25 x 25 x 2 mm GI angles and fasteners @ 1.2 m C/C including decorative design/pattern all as specified and directed Engr-in-Charge.

Supply & Fixing in repair cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1, diameter of outlet 100mm bore complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repair cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1, diameter of outlet 75mm bore complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repair cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1, diameter of outlet 100mm bore complete all as specified and directed by Engr-in-Charge .

Taking down PVC soil, waste and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

Supply & fixing 160 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, ceilings or laid in floor with and including fixing clips, bends, elbow, shoes bends etc (Note :- Measurement shall be taken along the centre line of the pipes) complete all as specified and as directed.

Supply & fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, ceilings or laid in floor with and including fixing clips, bends, elbow, shoes bends etc (Note :- Measurement shall be taken along the centre line of the pipes) complete all as specified and as directed.

Supply & fixing in repairs vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap and provision of lime concrete bedding complete all as specified.

Supply & Fixing Single Piece vitreous china WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size: 370x695x795 mm, S trap-300mm including connecting piece and making all connections complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repairs single piece slim concealed cistern vitreous china with wall mounting frame, installed kit and S-type drain pipe connection set for wall hung WC including accessories set complete including making all connections complete all as specified and directed by Engr-in-Charge .

Supply and fix health faucet with flexible pipe(ABS Body) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook fixed to 15mm bore stop cock and wall hook complete all as specified and directed.

Supply & fixing Counter Top Basin,Size: 705x460x195 mm vitreous china meticulously crafted from high quality materials with seamless finish white fixing with fastner/ bracket including 32mm dia brass CP waste coupling,15mm dia PVC connection with nuts and 32mm dia PVC waste pipe 90cm long and making all connections complete all as specified and as directed Engr-in-Charge.

Supply & fixing under counter wash hand basin vitreous china of size 605mm x 430mm x 200mm oval shape meticulously crafted from high quality materials with seamless finish white fixing with fastner/ bracket including 32mm dia brass CP waste coupling,15mm dia PVC connection with nuts and 32mm dia PVC waste pipe 90cm long and making all connections complete all as specified and as directed Engr-in-Charge.

Supply & Fixing in repairs toilet roll holder with flap chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) wall mounted complete all as specified and directed by Engr-in-Charge

Supply & fixing in repairs low level PVC flushing cistern (coloured) of heavy duty, 10 Ltrs capacity, syphonic action type complete with inlet, ball valve, float and handle including cast iron bracket and 32 mm bore PVC flush pipe and connecting to WC complete all as specified.

Supply & fixing in repairs vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe ) but including PVC waste pipe , providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement and fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern trap and waste pipe) complete all as specified.

Supply & fixing 32 mm dia flush pipe of polyethylene of high density for low level flushing cistern.

Supply & Fixing in repairs towel ring square with round flange of size 210mm x 210mm chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and as directed by Engr-in-Charge

Supply & fixing 32 mm dia PVC flexible waste pipe for WHB/urinal complete all as specified and directed.

Supply & Fix in repair soap container (soap dish) 110mm dia chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) fixed with chromium plated brass screw complete all as specified .

Supply & fixing in repairs Toilet paper holder of vitreous china (White) fixed to walls with chromium plated (CP) brass screws

Supply & Fixing in repairs Corner glass shelf with brackets and railing of size 255mm chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and as directed by Engr-in-Charge

Supply & Fixing in repairs 15 mm bore Pillar cock with lift type operating knob and base flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified .

Supply & Fixing in repairs 15 mm bore bib cock Bib Cock (Straight Line Model) With Wall Flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 5 mm bore angular stop cock with wall flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge.

Supply & fixing Overhead Shower ø140mm Round Shape Single Flow with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System complete all as specified and as directed

Taking up or down existing 15 mm bore GI water tubing including all fittings

Taking up or down existing 20 mm bore GI water tubing including all fittings

Supply & fixing 15 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Supply & fixing 20 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Disconnecting existing PVC water tank exc 1000 ltr but n.exc. 2000 lit capacityany of any pattern and in any position, setting aside (or lowering if required) complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tank 5000 Ltr capacity, (cylindrical vertical with closed top) including all connections for inlet, outlet, overflow and washout etc hoisted and fixed in position as specified in SSR Part-I including PVC cover with locking arrangement complete all as specified.

Disconnection existing tanks, setting aside (or lowering if required) for cleaning etc and hoisting and reconnecting and re-fixing in the same position capacity exc 1000 Ltr and n.exc 2000 Ltr complete all as specified and directed by Engineer-in-Charge.

Material & labour for machine cut cudappa stone slab 20-25 mm thick fixed independently and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Material & labour for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Material & labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Material and labour for 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete.

Supply & fixing cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges , balusters and similar articles exceeding 5 Kg each.

Dismantling of fencing, wire mesh of any type, and in any position by unscrewing nuts, fillets, clamps complete all as directed.

Dismantling posts struts (RCC/Angle Iron) any section including taking out embedded portion and making good distrubed ground complete as per existing including removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Material & labour for MS hand rails, half round or other stock section or core for wooden hand rail straight portion drilled and countersunk for balusters running bars, for doors balusters, nosing to steps including embedding in concrete and screwing etc wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified.

Material & labour for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified.

Supply only galvanised iron chain link fencing of any size and type complete all as specified and directed .

Fixing only GI chain link fencing including line wires, any mesh , size and type to any type of standards, rails, strainging bolts etc including provision of binding wire complete all as specified and directed .

Supply & fixing mild steel screw bolts 10 mm dia (mechine made) with hexaonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washer and one hexagonal or square nut n exc 5 cm long.

Material & labour for rendering 15mm thick in CM 1:4 on fair faces of brick surfaces, finished even and smooth (without using extra cement) complete all as specified and as directed.

Material & labour for preparation of new plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic paint (100 % acrylic) over one coat of self primer complete all as per manufacturers instructions and as directed by Engr in-Charge

Material & labour for mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Material & labour for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Material and labour for point wiring with 1.5 sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including 25mm wide PVC casing caping (ISI marked) with all accessories and terminated in and including PVC modular box with modular cover plate and frame of sutable size including 1.5 sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for the following :- Note: Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

One light point controlled by one switch

One Fan/bell point controlled by one 5A switch

One 5 Amps switch socket combination on independent board

One 5A flush type switch socket point on same board

Material and labour for point wiring with 2,5 Sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including suitable size surface PVC casing caping (ISI marked) with all accessories and terminated in and including surface PVC modular box with modular cover plate and frame of sutable size including 2,5 Sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for One 5pin, 15 Amps switch socket combination on indipendent board. Note: Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & Labour for point wiring (Work station for computer) with 4 Sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including suitable size surface PVC casing caping (ISI marked) with all accessories and terminated in and including surface PVC modular box with modular cover plate and frame of sutable size including 4 Sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for complete necessary electric connection for each work station point comprising of 03 Nos 5A sockets with 1.5 sqmm and 01 No 15A socket with 4.0 sqmm on same board complete all as specified and directed by Engr-in-Charge. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & labour for sub-main wiring with 2 runs of 4 Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC casing and caping not less than 25 mm wide (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4 Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains including taking up/down old unserviciable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) 2 runs of 4 Sqmm cable, One run of 4 Sqmm earth cable and PVC casing and caping shall be measured and paid as one length only.

Material & labour for sub-main wiring with 4 runs of 4 Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC casing and caping not less than 25 mm wide (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4 Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains including taking up/down old unserviciable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) 2 runs of 4 Sqmm cable, One run of 4 Sqmm earth cable and PVC casing and caping shall be measured and paid as one length only.

Supply & fixing LED batten fitting 2 x 21W, with heat shrinkable T8 batten fittings 2 Nos. 21 Watt cool white each, lumens efficiency 100 lm / W and lamp life not less than 50000 operating hours ,complete all as specified and directed.

Supply & fixing Modular switch 1 way 6 Amps, 1 module complete all as specified.

Supply & fixing Modular switch 1 way 6 Amps, 1 module complete all as specified.

Supply and fixing modular socket 16 Amps 2/3 pin 240 volts Ac combined 2 module complete all as specified

Supply and fixing modular socket 16 Amps 2/3 pin 240 volts AC combined 2 module complete all as specified

Supply and fixing Fan regulator , modular type 1 way 120W 2 module 240 volts flush type complete all as specified

Supply and fixing ceiling rose surface bakelite three terminal of size 60x50 mm,240 Volts AC complete all as specified

Supply & fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting VTPN 4 way, 440 volts with 100A Copper Busbar rating 440 Amps, for each phase, 2 Neutral bar, 2 Earth bar, dust and vermin proof with provision for DPX³ 160 MCCB as incomer DP MCB/Isolator/RCCB/RCBO as sub incomers and SP MCB's as outgoing complete all as directed.

Supply & fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators complete all as directed.

Supply & fixing ceiling fan 1200 mm sweep 230 volt 50 HZ AC, having air delivery not less than 200cum/min, 350 rpm single phase including down rod and fixing accessories and connecting up with three core flexible copper wire of size 23/0.0076 from ceiling rose to fan including taking down ceiling fan and depositing to MES store complete all as specified.

Supply and fixing MCCB 4pole 125A, 16kA rupturing capacity complete all as specified.

Supply and fixing MCB SP 6 - 32 Amps, 10 KA Rupturing capacity complete all as specified.

Supply and fixing MCB SP 40-63 Amps, 10 KA Rupturing capacity complete all as specified.

Supply and fixing MCB SPN 40-63 Amps, 10 KA Rupturing capacity complete all as specified.

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( avera Schneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof complete all as specified . Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Material and labour for 4mm GI wire earth continuity conductor or main earthing lead fixed to wall or buried in ground and fixed to panel transformer alongwith 20mm GI pipe light grade for protection complete all as specified .

Supply and fixing sheet metal enclosure with 2 pin and earth plug and socket complete with single pole MCB of 20 Amps 'C' curve complete all as specified & directed.

Supply & fixing Exhaust fan 300 mm sweep 240 Volt, 50 Hz, AC and 1400 rpm with lover shutter and connecting up with three core flexible copper wire of size 23/0.0076 from ceiling rose to fan including taking down and submitting to MES store complete all as specified.

Supply & fixing in repairs Air circulator fan 600 mm sweep 240 volt 50 HZ AC, air delivery 270CMM , 1440 RPM including taking down and submitting to MES store.

SHRI SAI ENTERPRISES

MADHU ENTERPRIZES

RAMESH ENTERPRISES

Vandan Enterprises

Sachin santosh dalvi