138WE/L-151/2025-26

Amount

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exc 15cm thick (below or above ground level ) and removing debris off the premises complete all as specified and as directed by Engr-in-Charge.

Demolition of precast concrete block walling built in cement mortar all as specified and as directed.

Taking down cement plaster on brick/ PCC block or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.

M&L for 15mm thick rendering on other than fair faces of brick work finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed by Engr-in-Charge.

M&L for 15mm thick rendering on fair faces of brick work finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed.

M&L for 5mm thick rendering on ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and as directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling incl preperaton complete all as specified and as directed.

M&L for preperation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of chalk whiting complete all as specified and as directed.

M&L preparing newly plastered wall surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint, complete all as specified and as directed.

Taking down chowkhat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc) complete all as specified and/or as directed by Engr-in-Charge.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:4 screed bed or bedding layer of mortar and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L glazed (coloured) ceramic tiles of size (350 x 250mm) x 7 mm / (450mm x 350mm) x 7mm thick, as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement as in dado, skirting etc to match with the shade of tiles including rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles all as specified and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc. laid bedded and pointed in any mortar.

M&L for machine cut Kota stone slab flooring 20-25 mm thick over & including cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 complete all as specified and/or as directed by Engr-in-Charge.

M&L for Cement concrete 1:4:8, type D-2, (using 40mm graded stone aggreate) 75 mm thick as in sub -floors, sub- bases, floors and pavings, etc. complete all as specified and/or as directed by Engr-in-Charge.

M&L for chequred cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments and laid over & including 20mm thick cement screed base (1:6) complete all as specified and/or as directed by the Engr-in-Charge.

M & L for 75 mm PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by the Engr-in-Charge.

M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and as directed.

M&L for precast solid blocks in cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Charge.

Material & labour PCC 1:3:6, type C1, (using 20 mm graded stone aggregate) as in hold fast block and like complete all as specified and as directed by the Engr-in-Charge.

M&L for pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixings lugs excluding hinges, lock strike plate, etc. complete all as specified and/or directed by Engr-in-Charge.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and/or as directed by the Engr-in-Charge.

S&F for 30 mm thick 2nd class soft wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supply and fixed to chowkats, complete all as specified and/or as directed by the Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the Engr-in-Charge.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (3 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by the Engr-in-Charge.

M&L for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type B-21 100 mm longs (3 Nos) suitable handle (2 Nos) (Glass / Wiremesh should be measured seperately) complete all as specified and/or as directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane, complete all as specified and/or as directed by Engr-in-Charge.

M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane including hacking down old broken glass, complete all as specified and/or as directed by Engr-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed.

S&F rotational moulded HDPE water storage tanks 1000 ltrs capacity and will be PUF insulated with 75mm thick PUF insulation of density 48 kg/Cum inner and out white two layers ISI marked ( cylindrical vertical type/rectangular loft type closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part I including all accessories (ie GI nipple etc), including provn of 20/25 mm dia spout for connecting inlet, outlet, over flow and washout pipes and taking down the existing ones, complete all as specified and directed by Engr-in-Charge.

S&F in repairs 25mm bore stop cock chromium plated screw down and high pressure screwed both ends for iron pipe or brass ferrule.

S&F 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR pipe fixed in repair.

S&F in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule.

S&F 25mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge taking up or down 25 mm bore steel tubing / PPR pipe and connections and set aside for re-use or removal to store.

S & F 32mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge and including taking up or down 32 mm bore steel tubing / PPR pipe and connections and set aside for re-use or removal to store.

S&F in repairs vitreous China squatting pan or orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet any pattern as in repairs incl bedding with PCC 1:2:4, type B-1, using 20 mm graded crushed stone aggregate, complete all as specified and directed.

Supply only 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs, 15 mm bore, PVC connection pipe 600 mm long with PTMT nuts at both ends complete all as specified and directed.

S&F in repairs sink with drain board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible Waste pipe including waste coupling.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, complete all as specified and as directed by Engr-in-Charge.

M&L Cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, complete all as specified and as directed by Engr-in-Charge.

M&L for brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and as directed by Engr-in-Charge.

M&L 25 mm thick PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in roof padding complete all as directed by Engr-in-charge.

M&L for 20 mm thick rendering in CM 1:4 over roof, surfaces finished even and smooth to receive the APP membrane, complete all as specified and as directed by Engr-in-Charge.

M&L priming surfaces and applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforming with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaced application including preparation of new surface of membrane and applying two coats of Aluminium paint, complete all as specified and as directed by Engr-in-Charge.

M&L for preperation of old plastered ceiling surface of any description and applying two coats of white wash complete all as specified and as directed.

M & L preparing old plastered surfaces of wall and applying two coats of distemper oil emulsion incl complete removal of existing treatment.

M&L for preparation of old plastered wall surface of any description and applying two coats of cement based paint complete all as specified and/or as directed by the Engr-in-Charge.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section including dismantling, complete all as specified and/or as directed by the Engr-in-Charge.

M&L for 2nd class soft wood clean sawn as in beeding for edges of ceiling, lining or wooden flooring work fixed with nails exc 6 sqcm and not exc 13 sqcm in section including dismantling complete all as specified and/or as directed by the Engr-in-Charge.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding including dismantling complete all as specified and as directed.

All as per serial item No 62 above, but as in ceiling.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling plain or corrugated steel sheeting any gauge thickness including nainital or similar pattern.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, complete all as specified and/or as directed by Engr-in-Charge.

S &F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering /clading to walls fixed with self tapping screws complete all as specified and directed.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs all as specified and as directed by Engr-in-charge.

S&F in repairsTowel rail 600mm long chromium plated (Minimum weight 190 gms).

M&L for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and/or as directed by Engr-in-Charge.

M&L for hard wood 2nd class factory made wooden boarded floors 10 mm thick and skirtings plained one side & edges tonged and grooved or rebated, including backing with thermocol sheets or as specified by manufacturers including dismantling, complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of new or old untreated wood or wood based surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation new steel surfaces of any description, not otherwise described, over 10 cm width / girth and applying two coats of synthetic enamel paint ovea a coat of red oxide primer, complete all as specified and/or as directed by Engr-in-Charge.

M&L for TMT mild steel bars, 10 mm dia and over, as in reinforcement, cut to length, bent to shape requied including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9 mm dia), complete all as specified and/or as directed by Engr-in-Charge.

M&L for providing precast cement concrete 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including use of necessary framework including demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing demolished material to a distance and removing rubbish off the premises, complete all as specified and/or as directed by Engr-in-Charge. Note : S&F reinforcement shall be maasued and paid separately.

M&L for 15mm thick rendering in cement mortar 1:4 on other than fair faces of brick walls or on concrete surfaces, finished even and smooth (without using extra cement) mixed with integral water proofing compound at 3% by weight of cement as per manufacturers instructions complete including taking down cement plaster of any description and removing rubbish off the premises, complete all as specified and/or as directed by Engr-in-Charge. Note : Water proofing admixture shall be measured and paid in this item only.

Supply only integral liquid water proofing compound.

S&F 110 mm bore PVC (SWR) pipe bends any radius, complete all as specified and/or as directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipe single socketed having compressive strength 655 - 675 Kg/cm2, in any length with rubber joints fixed to walls, complete all as specified and/or as directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipe bends, complete all as specified and/or as directed by Engr-in-Charge.

S&F 150 mm dia bore (inner dia) double wall corrugated HDPE pipe (SN 8) in any length including all fittings and jointing with eastomeric rubber link and cuppler/other jointing materials laid in trenches or in floor including concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) for 150 mm bore pipes including dismantling of cast iron / PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if required, complete all as specified and/or as directed by Engr-in-Charge.

S&F 110 mm dia bore PVC pies single socketed having compressive strength 655 - 675 Kg/cm2, in any length with rubber ring joints, laid in trenches or in floors including PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) bed to drain including dismantling of cst iron / PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if requied, complete all as specified and/or as directed by Engr-in-Charge.

S&F PVC (SWR) single junction (Single T) of 110 mm dia, complete all as specified and/or as directed by Engr-in-Charge.

S&F PVC (SWR) single junction (Single T) of 75 mm dia, complete all as specified and/or as directed by Engr-in-Charge.

Taking down carefully copper/ aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and/or as directed by Engr-in-Charge.

Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts FRLS cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor FRLS cable as continuous earth lead all as specified and directed for the following:-

One light/exhaust fan point controlled by one way switch.

One light point controlled by two way switch.

One switch socket outlet 6 Amps, 230 volts point on same board.

One switch socket outlet 6 Amps, 230 volts point on independent board.

All as item No 86 above, but using cables 4 sqmm size.

Supply and fix switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed.

Supply and fix switch piano flush button single pole 6 Amps 230 volts two way complete all as specified and directed.

Supply and fix socket outlet 2 in 1, 3 pin, 6 Amps flush type 230 volts complete all as specified and directed.

Supply and fix switch socket combination 2 in 1, 3 pin, 6 Amp flush type 230 volts complete all as directed.

Supply and fix switch socket combination 2 in 1, 5 pin, 6 and 16 Amp flush type universal outlet multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as directed.

Supply and fix ceiling rose, surface Bakelite three terminals complete all as directed.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Way complete all as specified and directed.

S&F in replacement of sheet metal enclosure for DBs double door when MCBs to be used single ple & neutral 240 Volts 08 way, complete all as specified and directed.

Supply and fix MCB SPN 63 Amp 240 Volts, 50 Hz AC, 'C' series complete all as specified and directed.

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 Hz AC, 'C' series complete all as specified and directed.

M&L for submain wiring along with earth wire FRLSH insulated copper conductor, single core cable in surface/recessed as required in & including PVC casing caping wire size 2 x 10 sqmm + 1 x 10 sqmm earth wire complete all as specified and directed.

Supply and fix LED down light (round, Cool white) of capacity 15 Watt, motion sensing based with 4.5 mtrs radius, 215 Volts complete all as specified annd directed.

Supply and fix in replacement 4' x 1' (feet) LED light fitting 36 Watt, 220 V, AC surface mounted box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repair 4 Way double door Tripple Pole Neutral vertical load line Distribution Board suitable for Flush mounting and suface mounting with 250 A copper bus bar with neutral bars and earth bars including MCCB 160 Amps TPN as incomer and SP/TP MCBs as outgoing and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Supply, install, testing complete water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes etc. including taking down exisitng ones, complete all as directed. Note :- Old retrieved water heaters to be deposited to MES store yard.

Supply and fix exhaust fan with plastic body, AC single Phase, 230V, 300 mm sweep including taking down the existing unserviceable exhuast fan and making necessary arrangements for fixing connectioning with flexible three core cable from the ceiling rose complete all as directed. Note :- Old retrieved fans to be deposited with MES store yard.

Supply and fix in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and/ or as directed by Engr-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and directed.

Supply and laying of XLPE insulated, armoured, heavy duty electric cables with stranded aluminium conductor rating 1100 volts grade of size 50 sqmm 3.5 core laid in trenches of passing through pipes ducts or fixed to walls / poles complete all as specified and directed.

M&L for excavation in tenches, not exc. 1.5m wide and not exc. 1.5 m in depth, for foundation, etc. or for laying UG cable in trenches not exc. 10 Sqm on plan and not exc. 1.5m in depth in any type of soil and getting out all as specified and directed by Engr-in-Charge.

M&L for returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed by Engr-in-Charge.

M&L for removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning to underground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, complete all as specified and directed by Engr-in-Charge. Note : Punned thickness of 18 cm will be measured and paid seperately.

Supply & laying of factory made, machine pressed, unreinforced, precast concrete cable cover LV type-1 flat size 250mm x 150mm x 40mm, complete all as specified and directed.

Supply and fix in replacement wall mounted FCUs of capacity 6000 K Cal/hr, complete all as specified and/or as directed by Engr-in-Charge. Make : Carrier / Voltas / Blue Star or equivalent approved make as approved by GE. Note:- Unserviceable FCUs retrieved from site shall be deposited to MES store.

Mehar Enterprises (BID ID -3433860)

M/s Koul & Sons (BID ID -3438046)