SPL REPAIR TO OR MD ACCN BLDG NO P 158 (01 TO 08) AT OLD ASSEY LINE OF 54 INF DOU AND PROVN OF TWO DEFI REFUSE BIN ENCLOSURE NEAR BLDG NO 15 OF CERTAIN UNIT UNDER AGE BR (SOUTH) NO II / AGE EM (SOUTH) OF GE (SOUTH) SECUNDERABAD

Amount

Taking down chowkhat (including grills/wire mesh) with shutters n.exc 1.50 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhat (including grills/wire mesh) with shutters n.exc 1.50 Sqm but n.exc 4.00 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed.

M&L second class hard wood Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F pressed steel door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates complete all as specified and directed. Note-PCC filling of hollow section shall be measured and paid seprately under relevant item.

S&F pressed steel door frame 105x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates complete all as specified and directed. Note-PCC filling of hollow section shall be measured and paid seprately under relevant item.

M&L for PCC typeC-1,1: 3:6 (using 20mm graded crushed stone aggregate) for cills,hold fast filling of hollow of pressed steel door frame etc complete all as specified and directed.

S&F 2nd class hardwood 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in Part I Sec 8 clause 8.20 (a) complete all as specified and directed.

S&F 35mm thick flush shutter solid core construction with block board core and ply wood face panels commercial type on both sides comlete as specified and directed.

S&F solid PVC door frames of sizes 50mm x 47mm made out of 5mm but single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube comlete as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core,frame as per specification & drawing comlete as specified and directed.

S&F Elixir 2000 Series Windows of Double Rebate windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 5 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work complete all as specified and directed. Make- Elixir/NCL

S &F framed work such as grills, grating etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars(for windows); barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work (Cupboard frame) conforming to Fe 290. Gde E-165 complete all as specified and directed.

S&F 300 mm long helical door springs including roller plate complete all as specified and directed.

S&F for 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S&F 125mm butt hinges heavy weight cold rolled mild steel complete all as specified and directed.

S&F in repairs 125mm butt hinges heavy weight cold rolled mild complete all as specified and directed.

S&F 100mm butt hinges heavy weight cold rolled mild steel complete all as specified and directed.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F Aluminium anodised barrel tower bolts 200mm of extrded section complete all as specified and directed.

S & F Aluminium anodised barrel tower bolts 125mm of extrded section complete all as specified and directed.

S & F 300mm size aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of seat cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F 100mm aluminium hasp and staple complete all as specified and directed.

S & F MS hold fast (FI 25X3, 250mm long) conforming to Fe-290, Gde E-165 complete all as specified and directed.

S&F Fixed Louvered Ventilators made of pre - painted steel (base steel as per IS 513 of -0.58 mm thick 'D" quality, galvanized as per IS 277 with zinc of 120 GSM) primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, The section for louvered ventilators should be of 33 x 56 mm Box section panelled with 4 mm pinhead glass with Ethyl propylene Diamine monomer Gasket (EPDM) and the sections cut to length mitre joined with corner bracket . Corner brackets made of CRCA with Zinc Phosphate. The frames to be fixed to the concrete/masonry wall by means of self expanding screws including 10 mm square guard bars with 6" pitch complete for finished item of work complete all as specified and directed. Make :Elixir/NCL

S&F Stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement morytar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

Demolition of un reinforced cement concrete in ground floors and paving n.exc 15 cm thickness (below & above ground level) complete all as specified and directed.

M&L for 25mm thick PCC 1:2;4 type B-0 as in sub base of tiles and surface even and smooth without using extra cement all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Squared/rectangular) area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including laying over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L Non skid ceramic coloured tiles 7 to 8mm thick (Squared/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed of 15mm thick in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x450x7mm thick in vertical surfaces of wall set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for RCC slab (Nominal mix )TypeB0 1:2:4 (12.5mm graded crushed stone aggregate)Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including crancking bending spirally for hooping for columns, hooking ends and binding/welding with existing reinforcement and including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed

M&L for Formwork flat to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and half moulded at one side including demolition of old stone any type complete all as specified and directed.

Demolition of brick work or stone boulders masonry built in Cement mortar (or) cement lime mortor including all quions, arches, pillars etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radins built in cement mortar 1:6 comlete as specified and directed.

M & L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 comlete as specified and directed.

Removal of damaged concrete along with loose damaged and cracked concrete/cover concrete at all specified locations up to beyond the corroded steel reinforcement to a depth of 10 mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chipper including high pressure water jetting to chipped concretand reinforcement and removal and disposal of debris within owners premises including all plant and machineries. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed. Depth of chipping may very from 50 mm to150 mm complete with labor, machinery, tools etc. The edges of repair locations shall be saw cut to a depth of at least 10 mm to avoid feather edgeing and provide a square edge. Removal of dust, loose particles, marine growth etc. from concrete surface manually by wire brush, mechanically or any other means to obtain a sound surface over areas other than above complete all as specified and directed.

Cleaning as directed & specified all rust/ scales/corrosion from reinforcement bars using rust remover agent like Reebaklens RR of STP/Dr Fixit or equivalent having Specific Gravity 1.16 - 1.22. The material to be applied to the rusted metal using brush and make leaving to dry for 30 mins & washing surface with fresh water as required to exposed reinforcement bars complete as specified.

Supplying and laying polymer modified micro-concrete like Renderoc RG of Fosroc make or STP or Dr fixit having compressive strength (BS 4551-80)-50 Mpa at 28 Days, Tensile strength- 2 Mpa @ 28 Days, Flexural Strength(BS 4551-80)-5 Mpa at 28 Days, Young’s modulus-25 kN/mm2, Expansion characteristics (ASTM C827 - 1987)Unrestrained expansion 1 to 4 %,Pressure to restrain Plastic Expansion-Approx. 0.004 N/mm2,Thermal Conductivity – 1.5 W/m C. Pouring the same into the formwork using suitable arrangement or if required using pumping device for uniform flow of micro concrete. The side shuttering can be removed after 3 days and the bottom shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate. Item rate is inclusive of materials all Labour, tools and tackles, scaffolding and transportation etc comlete as specified and directed.

Taking down plastering on brick walls and concrete surface etc including racking out joints, hacking for key, scrabing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on concrete or fair faces of brick work in CM 1:6 finished even and smooth without using extra cement comlete as specified and directed.

M&L for rendering 15mm thick on concree or fair faces of brick work in CM 1:4 finished even and smooth without using extra cement complete all as directed and as specified.

M&L for rendering 10mm thick in CM 1:4 rendering on cocrete surface such as ceiling chajjas etc finished evena and smooth (without using extra cement) all as specified and as directed.

Demolition of un reinforced cement concrete in any position and any thickness below and above grund level comlete as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on roof concrete surface while concrete is green mixed Water proofing compound @ 3% of total weight of cement used or as per manufacturer's instruction finished the surface smooth and even without using extra cement complete as specified and directed. Note:- WPC shall be measured and paid separately under relevant item.

M&L for priming the plastered roof surfaces with bitumenous primer @ 0.30 kg over applying hot bitumen VG-30 1.2kg/Sqm and applying APP based polymeric membrane weighing 3 kg per Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/per sqm) and on primed surface by forced torch application over that applying bitumen base alluminium Paint 0.2 Kg/Sqm including complete removal of old APP membrane complete comlete as specified and directed.

M&L for 40mm Thick PCC (1:2:4) Type B1 (using 20mm graded crushed stone aggregate) as in roof mixed Water proofing compound @ 3% of total weight of cement used or as per manufacturer's instruction over slab including necessary form work and finishing the exposed surfaces fair even without using extra cement complete as specified and directed. Note:- WPC shall be measured and paid separately under relevant item.

M & L for rendering 15mm thick on concrete or fairfaces of brick work in CM 1:4, finished even and smooth without using extra cement but mixing WPC complete,all as directed and as specified (Note:- WPC measured and paid separately).After plastering the sunken surface, sunken portion to be filled with water and tested for 72 hrs (after required period of curing) to observe leakage/seepages, leakages/seapage if any shall be arrested by pressure grouting and re-tested till leakage/seepages completely stopped. After pointing test, the surface shall be dried and bottom and sides of the sunken slabs shall be treated, priming the plastered surface with bituminous primer conforming to IS-3384 @ 0.3 Kg per Sqm and applying a tack coat of industrial bitumen 85/25 @ 1.2 kg per Sqm over which applying using glass fibre base bituminous felt type II and grade 2 (conforming to IS-7193 1994) and applying one coat of hot blown bitumen of grade 85/25 @ 1.5 Kg per Sqm including 450mm long 25mm dia medum grade GI pipe shall be provided at the lowest in case of leakage. The joints in CI/GI/PVc pipes, Nahani traps, WC and P/S trap connection shall be made leak proof. The gap around the pipes in walls/beams shall be properly filled and sealed with water proof joints fillers complete all as specified and directed.

M&L for PCC 1:3:6 type B0 (using 12.5mm graded crushed stone aggregate) as in levelling course including weathering slightly rounded or chamfered angles and throating as directed complete all as specified and as directed.

S&F 25 mm bore CPVC pipes SDR 11 pipes & Plain CPVC SDR 11 fittings and fixed complete to walls and ceiling or laid in floors including taking down existing GI/CPVC complete all as specified and as directed

S&F in repairs of CPVC pipes 20 mm dya SDR 11 & plian CPVC SDR 11 fittings in wall /ceiling or laying in floors taking down existing GI /CPVC pipes complete all as specified and directed.

S & F in repair bib tap 15mm bore, fancy type, chromium plated, cast copper alloywith crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repairs 15mm bore wall Mixer Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed ll as specified and directed.

S & F in repairs 15mm bore stop valves fancy type chromium plated screwed both ends for iron pipe for unions and fixed with long shank and cup (concealed type).

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore all as specified and directed.

S&F 600 mm long PVC connections, 15 mm dia with PTMT nuts, complete all as specified and as directed.

S & F in repair chromium plated 125mm swivel shower complete all as specified and as directed.

S& F in repairs water closet (squatting pan) complete including provision of lime concrete bedding 'Orissa' pattern size 508 x 440mm white, integral foot rests including flushing cistern and flush pipe,PVC connection of size 450mm complete all as specified and directed.

S&F in repair EWC Pedestal pattern WC ,any colour incl EWC seat Cover,10 ltr capacity PVC ,LLFC,32 mm dia PVC flush pipe including CP Toilet Paper holder etc complete all as specified and directed.

S&F in repair vitreous china wash basin with padestal , white flat size 550x400mm incl bracket cutting for and pining in ends of brackets or erecting stand including PVC connection pipe 15 mm bore 450 mm long , waste coupling of PTMT , PVC waste pipe complete all as specified and directed.

S & F tubular towel rail brass chromium plated 20mm dia D type 60 cm, between the flangers all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)

S & F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including waste coupling and waste pipe and including bedding in cement mortar to dwarf wall or including fixing cantillever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm.

S & F kitchen plate rack size (24x36x10')made of stainless steel, complete all as directed and as specified by Engineer-in-Charge.

Demolition of existing tank of any description and S & F 500 ltrs rotational moulded polythylene water storage tanks, cylindrical vertical with closet top hoisted and fixed in position all as specified in Part-I including 20mm dia PVC high pressure float valve complete all as specified and as dirtected.

S & F 75mm dia, PVC (SWR) floor trap, plain with grating and jointing to waste pipe with solvent cement and fixed in PCC 1:2;4, type B1, complete all as specified and as directed.

S & F 110mm PVC (SWR) WC connector with lip ring complete all as specified and as directed.

S & F 110mm PVC (SWR) WC connector bend type complete all as specified and as directed.

S & F 75mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

S & F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

S & F 75mm bore PVC (SWR) branch piece with access door, single T equal or un-equal complete all as specified and as directed.

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls, complete all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls, complete all as specified and as directed.

M&L for Preparatioin of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat pink primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of distemper oil emulsion over a coat of cement primer over a coat of 1.0mm thick Birla wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of wall surfaces and applying two coat of distemper oil emulsion over a coat of primer over a coat of 1.0mm thick Birla wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of cement base paint over a coat of cement primer including preparation of old plaster surfaces of walls complete all as specified and directed.

M&L for applying one coat of exterior emulsion paint (weather proof) on old treated wall surfaces complete all as specified and directed. Note : weather proof paint will be done by roller only, after complete removal of old loose flakes and wall, roof hight portion is upto ht 7.50m necessary scaffolding to be provided.

S&F fancty type power coated 20mm dia curtain rod with fancy type bracket complete all as specified and directed.

S&F for 18 mm thick , prelaminated medium density fibre (MDF) , interior grade, prelaminated one side with decorative choice lamination and other side balancing white with lamination fixed with screw to timber/ steel frame work as in CB shutter, shelves etc with PVC liping on all exposed edges on same texture and shade. Stainless steel cleat of suitable size will be use to fix the shelves of CB and cabinets complete all as specified and directed.

S&F Auto closing hinges 35mm of 0 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed.

S&F D-type cabinet handles premium quality, 100 mm long excruded brass handles complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) laid in panels surface finish even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type B2 (Using 40mm graded crushed stone aggregate) as in sub base floor laid in panels and finished top even and fair without using extra cement complete all as specified and directed.

S&F Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry with grey cement and pigments in floors over a15mm thick screed bed in CM (1:4) complete all as specified and directed.

S&F 20-25 mm thick Pre polished kota stone as in floors over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to achieve mirror finish and rounding chamfered edges where directed complete all as specified and diirected.

All as per above item No 95 but 20 to 25m thick Pre polished kota stone slab as in small wiidth in vertical surfaces like landings, risers,, treads, skirtings, dado, etc over and including 10mm thick pcking coat in cement mortar 1:4 complete all as specified and directed.

Rounding to edges of kota stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for PCC type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in roof curves or muds, stops, rounded or chamfered on edges complete all as specified and as directed.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in hard dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard dense soil complete all as specified and directed.

M&L for Hardcore of gauge exc. 63mm, deposited, spread and levelled in layers n. exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate as in flooring finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) with solid blocks, exc. 10 cm in width set in CM 1:4, etc complete all as specified and as directed

M&L for preparation of new iron surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard /dence soil complete all as specified and directed.

Removing excavated soil to a distance n exc 50 m and deposited where directed at a level n exc 1.5M above the starting point complete all as specified and directed.

M&L for 100mm thick Plain Cement concrete type C-2, 1:3:6 using (40mm graded crushed stone aggregate) Laid in flooring complete all as specified and directed.

M&L for 75mm thick Plain Cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) Laid in base of flooring complete all as specified and directed.

M&L for 50mm sand filling under floor complete all as specified and directed. Note- sand shall be sharp angular free from organic matters.

S&F Machine pressed precast conctete interlocking paver block with grey cement and colour pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket, power, security lights or bulkhead) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down ceiling /exhaust fans diamantling blades completeand deposted to MES yard complete all as specified and directed.

Taking down existing unserviceable Distribution boards / AC board with MCB's any size and any type complete all as specified and directed.

Taking down existing submain wiring of any size or any type complete all as specified and directed.

Taking down old earthing material complete all as specified and directed.

M&L for Point wiring complete with two runs of 1.5 Sq mm (for Phase and neutral) PVC insulated unsheathed multi stranded ,copper conductor FRLSH cable of 1100V grade drawn through and including new non metallic rigid PVC concealed conduit medium grade , ISI marked , 20 mm bore with conduit accessories for wiring concealed in wall, including provision of fabricated branded pressed steel terminal box concealed of suitable sizes with 1.6mm thickness including modular cover frame & box of suitable size for modular switch boards/sockets/regulators of any size modules for housing modular switches, sockets, fan regulators etc and provn of 1.5 Sqmm PVC insulated unsheathed copper conductor cable of green colour to common earth dolly etc complete all as specified and directed for one light /Fan point controlled by one switch. Note:- (1) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (2) The cost of cutting of chases of required width and depth for concealled conduit incl plastering, making good to disturbed surface, painting two coats to match the existing wall colour is deemed to be included in the quoted rate by the contractor.

All as per item No-117 here in above but for one three pin switch socket 6 Amps outlet on independent board.

All as per item No-117 here in above but for one three pin switch socket 6 Amps outlet on same board.

All as per item No-117 here in above but for one light point controlled by two nos of two way switches.

All as per item No-117 here in above but for One Bell point controlled by one, bell push

All as per Sl item No-117 here in above but for 2.5 Sq mm (for Phase and neutral) PVC insulated unsheathed multi stranded, copper conductor FRLSH cable for one 15 Amps socket out let independent point.

M&L for Point wiring complete with two runs of 4 Sq mm (for Phase and neutral) PVC insulated unsheathed multi stranded ,copper conductor FRLSH cable of 1100V grade drawn through and including new non metallic rigid PVC concealed conduit medium grade , ISI marked , 20 mm bore with conduit accessories for wiring concealed in wall, including provision of fabricated branded pressed steel terminal box concealed of suitable sizes with 1.6mm thickness including modular cover frame & box of suitable size for modular switch boards of any size modules for housing modular switches, sockets, etc and provn of 4 Sqmm PVC insulated unsheathed copper conductor cable of green colour to common earth dolly etc. complete all as specified and as directed for one 15 Amps socket out point independent board Note (1) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (2) The cost of cutting of chases of required width and depth for concealled conduit incl plastering, making good to disturbed surface, painting two coats to match the existing wall colour is deemed to be included in the quoted rate by the contractor.

S&F Modular switch 1 way 6A , 1-module complete all as specified and directed.

S&F Modular switch 1 way 16A with indicator, 1-module complete all as specified and directed.

S&F Modular socket, shuttered type, 6A - 3 pin 2 -module complete all as specified and directed.

S&F Modular socket, shuttered type, 6/16A - combined 2-module complete all as specified and directed.

S&F Modular switch 2 way 6A,1 module complete all as specified and directed.

S&F Modular Bell Push 6A, 1 Module with bell symbol complete all as specified and directed.

S&F calling bell ding dong working on 230 volts AC with different ring tones optional complete all as specified and directed.

S&F 3 pin, 6 A, 250 V ceiling rose having terminal capacity 3 X 1.5 mm² IP 20 protection complete all as specified and directed.

S&F TV CO axial socket outlet fixed to wall on modular complete all as specified and directed.

S & F Single pole and Neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps (AC Box) complete all as specified and directed.

S&F ceiling fans complete with blades,copper winding, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery not less than 210 CFM with service value more than equal to (≥) 6.00, BEE Five star rated with brushless direct current motor (BLDC) white colour complete all as specified and directed. Make:Gold Medal cat part no.SCFS 500748/Bajaj Cat part No:ENERGOS 28/ Crompton Cat part No:ENERGION RIVIRA/Havells Cat part No:PRO 28BLDC/Luker Cat part No:ECO28NEOBLDC Regulator 222cmm

S&F Exhaust fan made of sturdy Engineering plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm sweep complete all as specified and directed. Make:Havells Cat part No:Vetil Air DX HS/Gold Medal EFS850310 AIR MAXX/Crompton VENTILUS250MM/Bajaj-Maxima neo/Luker cat part No:Viento LX10

S&F Exhaust fan, metal body AC single Phase 230V of size 300 mm sweep,RPM 1200 with, copper winding,blades,rag-bolts, and frame and louvers complete including making suitable size hole in wall for fixing of fan complete all as specified and directed. Make: Havells Cat part No:Ventil air DSB /Gold Medal EFS851012 HAVAC PLUS /Crompton drift air plus300mm/Bajaj-Supreme plus/Luker cat part No:TuuliLME12

S&F 20 W surface / wall mounted LED batten light fitting aluminium extrusion input voltage range 250 V, input frequency 50 Hz, efficacy not less than 120 Lumen/Watt, rated llife 50000 Burning hours including 2 nos PVC Connector blocks electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixturecomplete all as specified and directed. Make: Crompton CCS-100-20-65-HSL2-DP-NWH/ PHILIPS BN308CLED20S-6500L120PSUWH / WIPRO LL31-251-XXX-65AL5/Havells ENDURALINEARPROBS20WLED865PCSSIND/Bajaj-BCLAB20WCWLEDXT

All as per item No-137 here in above but LED batten light fitting10 Watts 2 feet surface / wall mounted efficacy not less than 100 Lumen/Watt rated life 25000 burning hours complete all as specified and directed. Make:Crompton CCS-103-10-65-SL-DP-NWH/ Havells LHEXAZP7PN1W010 / Bajaj-BCLAB10WLEDCWLED

S&F in replacement of old unserviceacble light fitting with LED light fitting 10Watts bulkhead luminaires, efficacy not less than 100 lm/w, rated life 25000 burning hours including LED light driver holder connecting up with three core flexible copper conductor cable IP 65 out door type metal body of suitable size complete all as specified and directed. Make: Crompton CIS-306-10-57-SL-DP-NBK/ HAVELLS HEXAFT10WLED857SSYMBOPC /Bajaj-BIBWP10W LED

S&F LED security light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant,efficacy not less than 120 lm/Watts,rated life 50000 burning hours complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with wall mounting bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete suitable for pop/grid false ceiling complete all as specified and directed.

S&F Electric water heater, storage type,vertical, single phase, electric operated, 50Hz, steel body heating element up to 2 KW capacity 25 Ltrs, BEE 5 star rated innner tank as per OEM specification with minimum 2 years warranty on over all product (inner tank ,heating element & thermostat) complete with all accessories such as safety valve, thermostate, NRV, connection piece, FRLS multistranded copper conductor cable 3 core PVC insulated, plug top 3 pin 15 Amp , 15 mm dia, brass coupler, flexible pipe suitable to withstand upto 120 °C for hot and cold water, Anchor fastener- 04 Nos of suitable size etc complete all as specified and directed. Make:Crompton VERSA 25L / HAVELLS FABIA GHWAFATWB025 / Gold Medal SWMS01025VWH / Bajaj SPECTRUM15096625L/Luker-LPST25

S&F in replacement of TPN DB 4 way double door horizontal made out of CRCA sheet housing duly powder coated & confirming to IS specification complete all as specified and as directed.

S&F single pole & neutral, double door, metallic distribution board 8 ways conforming to IEC 61439-3, suitable for flush / surface mounting with provision for DP MCB as incomer and SP MCBs as outgoing, concealed in wall complete all as specified and directed.

S&F MCB SP 6 to 32 Amps 'C' series complete all as specified and directed.

S&F MCB, single pole, 40 Amps, 240 Volts, connecting with copper lugs complete all as specified and directed.

S&F of MCB three phase and neutral (TPN), 125 Amps, 415 Volts,connecting with lugs complete all as specified and directed.

S&F of MCB single phase and neutral (SPN), 40 Amps, 230 Volts, connecting with lugs complete all as specified and directed.

S&F Submain wiring with 2 runs of single core 6 sqmm PVC insulated FRLSH multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic rigid PVC concealed / Surface conduit and conduit accessories of medium grade not not less than 25mm dia including one run of single core 6 sqmm PVC insulated sheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board including removing the existing unserviceable submain riwing complete all as specified and as directed. Note:-(1) The wiring shall be done in proper color coding using red,yellow,blue for phases , black for neutral and green for earth (2) The cost of cutting of chases of required width and depth for conduit incl plastering ,painting two coats to match the existing wall colour is deemed to be included in the rate quoted rate. (3) The three runs of copper wire one run of PVC coduit is shall be measured as one running meter.

M&L for Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less' than 1.5meters below normal ground level, earth plate connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES 2009 (part I Specifications) connected to earth test point all as specified or indicated including testing on completion, including necessary excavation and earth work in any type of soil and adequate quantity of common salt & charcoal for alternate layer around the earth plate, including PCC (1:2:4) pit and 10mm thick C.I. cover with arrangement of hinge to 40x40x6mm C.I. angle iron frame, including 20mm dia G.I. pipe for watering purpose with the arrangement of funel and wire mess, including GI pipe of 15 dia for earth lead protection complete incl taking down old one complete all as specified and directed.

M&L for earth continuity conductor 4 Sq.mm dia GI or steel wire complete incl taking down old one complete all as specified and directed.

M&L for cutting of wall in required shape using machine core cutting only and making opening,at any height, fixing of suitable premoulded block of required suitable for mounting of exhaust fan including wire mesh and making good the disturbed surfaces,plastering,matching with existing colour along with hole size matching with existing colour and clearing all debris and making the work area clean all as specified and directed .Note:The quoted rate includes for all/any number of openings required at any place for proper ventilation of the site.

S&F PVC sleeve tail piece for fixing exhaust fan on the wall complete all as specified and directed.

S&F steel water tubing medium grade 15 mm dia including all fittings laid on wall complete all as specified and directed.

S&F Bib tap 15mm dia chromium plated copper alloy material complete all as specified and directed.

S&F chromium plated Gate valve 15mm dia complete all as specified and directed. .

M/S NOVA CONSTRUCTIONS (BID ID -3454815)

GADUSU RAMESH CONTRACTOR (BID ID -3455672)

GUTHIKONDA BROTHERS (BID ID -3460442)

R G NAIDU CIVIL CONTRACTOR AND BUILDERS (BID ID -3455104)

SAI RUPA CONSTRUCTIONS (BID ID -3455559)

S.R.M.K Enterprises (BID ID -3460750)

K LAKSHMAN SINGH AND CO (BID ID -3460053)