Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹27.8 LAccepted-AOC | L1 | Accepted-AOC Lowest bid. | |
| 2 | L2₹27.8 L+₹5,224.10 (0.19%)Rejected-Finance | L2 | Rejected-Finance Other than lowest bid. | |
| 3 | L3₹30.3 L+₹2.6 L (9.22%)Rejected-Finance | L3 | Rejected-Finance Other than lowest bid. | |
| 4 | L4₹30.8 L+₹3.1 L (11.0%)Rejected-Finance 451 NEAR RADHA KRISHAN MANDIR VPO MAMUN PATHANKOT 145001 PB | PATHANKOT | PATHANKOT | PUNJAB | 145001 | L4 | Rejected-Finance Other than lowest bid. |
Tender Value
₹31 L
EMD Value
₹62,000
Closing Date
14 Jan 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE SOUTH MAMUN
GE SOUTH MAMUN PATHANKOT-145001
SPL REPAIR TO BLDG NO T-05, SEWAGE SYSTEM, PROVN OF SENTRY POST, HARDSTANDING AND GAZEBO AT MAMUN MILITARY STATION UNDER GE (SOUTH) MAMUN
2022_MES_564377_2
GE(S)/M-48/2022-23
Open Tender
Miscellaneous Works
Item Rate
180 days
GE SOUTH MAMUN
AS PER NIT
8 documents required · 8 mandatory
₹500
GE SOUTH MAMUN
₹62,000
Yes
4 Feb 2023
26 Dec 2022
21 Jan 2023
26 Dec 2022
14 Jan 2023
2 Jan 2023
Amount
Taking down cement plaster on brick or stone walls or concrete surfaces built in cement mortar including racking out joints, hacking for key, scrubbing down with water etc.,to recive plaster complete all as specified and directed.
Taking down chowkhats or frames exc 1.5 Sqm but not exc 4.0 Sqm each (without taking off shutters from the frame), complete all as specified and directed.
Taking down chowkhats or frames not exc 1.5 Sqm each with shutter (without taking off shutters from the frame), complete all as specified and directed.
Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.
Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.
Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick watering and well ramming and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed.
Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.
Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.
M&L for hard core of broken stone or boulders of gauge n. exc. 63 mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.
M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.
M&L for PCC 1:5:10 type E2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.
M&L for 100 mm PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregates) as in sub base etc.complete all as specified and directed.
M&L for 150 mm PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregates) as in sub base etc.complete all as specified and directed.
M&L for PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in kerbs of interlocking tiles etc, complete all as specified and directed.
M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete complete all as specified and directed.
M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.
M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies and in shelves and the like complete all as specified and directed.
M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.
M&L for brick work with sub class ‘B’ (old size) bricks, straight or curved on plan exc 6 metre mean radius, built in CM 1:6, including demolition of old brick work complete all as specified and directed.
M&L for form work to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter complete all as specified and directed.
M&L for form work to sides and soffits of flat, rough finished surfaces of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.
M&L for form work to edges of concrete flat, treads, window cills etc and similar items including edges complete all as specified and directed.
M&L for form work to soffits of flat, rough finished surfaces of concrete of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick(Horizontal or sloping) complete all as specified and directed.
S&F pre-laminated lead free factory made 18mm (+ 0.7mm) thick 100% solid WPC (wood polymer composite) sheet having high natural fibre content 25 to 30% wood colour sheets having density not less than 600Kg/cbm and should be 100% termite/water proof, fire retardant, Eco friendly, finish at all edges for making edges lipping/bending, manufactured by single layer extrusion process with excellent screw holding capacity and shore D hardness complete all as specified and directed.
M&L for 2nd class hardwood,as in plain fillets framed work, square revctangular or triangular in section , clean sawn, secured with nails or brads exc 13 but n.exc 25 sqcm in section complete all as specified and directed.
S&F 35mm thick wire guazed and skeleton shutters (2nd class hardwood), open rebated and prepared to receive wire cloth, gauze etc. without sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing wire cloth etc, sizes of members of shutters as specified in SSR Part-1, Section 8, Clause 8.24(a), supplied and fitted to chowkats, including two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
S&F 35mm thick plain framed, panelled (factory made shutters (2nd class hardwood), with lock rails and panel of 9mm thick BWP commercial ply. The size of rail and stiles as per IS-1003(Part-1) (larger size to be provided kiln seasoned and chemically pressure treated, fitted to chowkats, including two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
S&F in repair aluminium anodised (minimum thickness of powder coating 50 micron) frame for door, window and ventilator of any size with one or more rebates including jointing cleats for fixing etc and taking down existing aluminium frame complete all as specified and directed.
S&F in repair aluminium anodised door shutter, aluminium section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, 2 Nos handles 150mm long in each door and two Nos 150mm long aluminium tower bolts in each shutter, SS hinges 125mm size-04 Nos, anonised aluminium snap beading, fixed with screws, complete all as specified and directed.
S&F in repair anodised aluminium window and ventilator shutters, side hung or sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.), hinges 100mm long (2 Nos) and suitable handles as required, complete all as specified and directed.
S&F 12mm thick aluminium colour ACP sheet fixed with rubber beading and glazing clips to aluminium frame complete all as specified and directed.
S&F door closer hydraulically regulated, aluminium extruded section body, designation No. 1, universal type, suitable for door shutters upto 700mm in width and of weight not more than 35 kg complete all as specified and directed.
S&F "as in repair" double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and directed.
S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised 30mm width of flaps (when open), complete all as specified and directed.
S&F 100mm long butt hinges, medium weight, cold rolled mild steel, (ISI) marked complete all as specified and directed.
S&F 150 mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.
S&F 100 mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.
S&F 150mm long, aluminium anodised, barrel tower bolts of extruded section, ISI marked, complete all as specified and directed.
S&F Aluminium alloy, anodised, sliding door bolt 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed complete all as specified.
S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.
M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.
M&L for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.
M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.
S&F Solid PVC door frame wooden high density filament (HDF) double rebated of size 50mmx95mm processed with polymer fins and different wood fibre, fixed to opening including necessary lugs/hinges, lock strike plate etc complete all as specified and directed.
S&F Factory made UV wood grain printed panelled/plain PVC single piece door shutter 30mm thick style, consisting of frame made out of MS tube 19 guage thickness & size of 19mmx19mm for stiles, top and bottom rails. MS frame shall have a coating of steel primer, the frame shall covered with heat moulded wood grain UV printed PVC sheet tap fixed in MS frame welded to the stiles and rails with suitable PVC sheet beading and jointed togetherwith solvent cement, fixing in frame at site complete all as manufacturer's specifications and ditrected by Engineer-in-charge.
M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement complete all as specified and directed.
S&F pressed steel frame of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) in frames/hold fast blocks, complete all as specified and directed.
S&F Box type steel windows and ventilators, comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube, factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes shall be measured and paid separately under respective items of BOQ) with steel handle and steel peg stay dovetailed or welded including 2 Nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to FI frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in PCC blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing No. CEPZ/C-TD/026/13 sheet 5/5 to 5/5.
M&L Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.
M&L Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in ridge/valley , gutter or straight flashings etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.
M&L for Framed wk such as grills, grating with ends of bars shouldered etc and similar work confirming to Fe-410-0 complete all as specified and directed.
M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.
M&L Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W (Gde E- 250) quality A complete all as specified and directed.
M&L for preparation of new steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.
M&L for preparation of old steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.
M&L for APP modified roof treatment over existing non-accessible RCC roof slab/chajjas/canopy/parapet wall, to be executed through approved applicator of the membrane manufactured with following specifications, complete all as specified and directed :- (a) Cleaning the top surface of RCC roofing properly with water. (b) Applying oil bound bitumen primer @ 0.30 Litre/Sqm, manufactured by the same agency as that of APP with a density 0.87-0.89 KG/Litre at 25 degree centigrade on prepared surface. (c) Laying of membrane not less than 3.0mm thick APP modified water proofing membrane weighing not less than 3.60 KG/Sqm reinforced with non woven polyster fiber weight not less than 160 Gms/Sqm using butane torch by torch application with 10cm overlap and 15cm end lap. (d) Top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 KG/Sqm as prescribed by manufacturer of membrane. (e) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC 1:2:4,type B-0.
Supply only integral water proofing compound complete all as specified and directed.
M&L False ceiling of 8 to 9 mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.
M&L 50mm for PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) including WPC as per manufacturer instructions as in padding etc complete all as specified and directed
M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.
M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection. Concrete shall be laid in alternate bays n.exc 3 m in length finished fair and even including provision of joints of 6 mm wide and 10 mm deep along the wall and bays filled with bitumen mastic (1:3) complete all as specified and directed.
M&L for 50 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in flooring laid in panels surface. Concrete shall be laid in alternate bays n.exc 3 m in length finished fair and even including demolition of existing floor of any description complete all as specified and directed.
M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in plinth protection. Concrete shall be laid in alternate bays n.exc 3 m in length finished fair and even including provision of joints of 6 mm wide and 10 mm deep along the wall and bays filled with bitumen mastic (1:3) complete all as specified and directed.
Extra for forming fair finished drain or channels 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stops ends etc., complete all as specified and directed.
M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishescomplete all as specified and directed.
M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishescomplete all as specified and directed.
M&L for light shade vitrified tile 8 to 10mm thick coloured tiles , area of each tile n exc 0.36 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishescomplete all as specified and directed.
M&L for machine cut granite stone 18 to 20mm thick over and including 20mm thick on wall clading,steps,jambs,pillars,window cills cooking plateform screed bed in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in floors / cills etc, and moulding at edges (if required) complete all as specified and directed.
M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50 mm thick screened river washed sand cushion, complete all as specified and directed.
&L for precast machine pressed designer coloured chequered tiles with glossy finish (factory made rectified) of any size of 20mm thick, top layer glazed made in any type of cement and pigment, in required patterns in floor etc set & jointed in neat cement slurry & pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.
M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.
M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.
M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling / top and sides of chajjas/facia of roof projection including necessary formwork, finishing the surface even and smooth without using extra cement, complete all as specified and directed.
M&L for newly plastered or unplastered surfaces and applying 2mm thick wall care putty for making the surfaces smooth and applying two coats of oil emulsion distemper, complete all as specified and directed.
M&L for complete removal of existing treatment and applying 2mm thick wall care putty for making the surfaces smooth and applying two coats of oil emulsion distemper, complete all as specified and directed.
M&L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed.
M&L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.
M&L for preparation of newly plastered surfaces of external wall and applying two coats of cement base paint including curing before and after, including a coat of alkali-resistant priming paint complete all as specified and directed.
M&L for preparation of old surfaces of external wall and applying two coats of cement base paint including curing before and after, including a coat of alkali-resistant priming paint complete all as specified and directed.
S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.
S&F 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.
S&F 3mm thick Figured glass, pin head type in square not exc 0.50 Sqm each pane, fixed with oil putty, including,complete all as specified and directed.
S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.
S&F Rotational moulded polyethlene water storage tank of capacity 500 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position, including 20mm dia PVC ball valve, high pressure of PTMT epoxy coated aluminium rod and high density plastic ball screwed for iron pipe fixed in position (min. wt. 20mm-210gm/25mm-455gm) complete all as specified in SSR Part-1 and directed.
M&L"as in repair" for 15mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.
M&L"as in repair" for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.
S&F "as in repair" 20mm bore mild steel drapery rod with 1.0mm thick PVC wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.
S&F "as in repair" 50mm bore polished hardware knobs fixed with screws , complete all as specified and directed.
S&F ball catcher with proper magnetic effect fixed with shutter, complete all as specified and directed.
S&F 20'' long telephonic slider to facilitate drawer slide of steel ball bearing fixed with SS screws, complete all as specified and directed.
S&F 5mm thick PVC sheet one side prelam sheet for kitchen cabinet/cupboard complete all as specified and directed.
S&F "as in repair" 15mm bore bib tap, with flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.
S&F "as in repair" 15mm bore Pillar tap, cast copper alloy, fancy type, with capston head, chromium plated, screwed down, high pressure with or without letters, hot or cold with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed.
S&F "as in repair" 15mm bore stop valve/angle valve , cast copper alloy (ISI marked), screwed down, high pressure with crutch or butterfly handle, screwed both ends for pipe or for unions complete all as specified and directed.
S&F "as in repair" 15mm bore stop valve, cast copper alloy (ISI Marked), fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with capstan head, screwed both ends, complete all as specified and directed.
S&F "as in repair" jet spray for EWC including required length of tube fixed with existing water tubing/stop cock including necessary fittings complete all as specified and directed.
S&F "as in repair" PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.
S&F "as in repair" Vitreous china wash basin, white flat back aize 550x400mm, including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe fixed in repair including waste copling 32mm size full thread complete all as specified and directed.
S&F PVC connection 15mm size of length 450mm with PTMT nuts, complete all as specified and directed.
S&F "as in repair" brass tubular towel rail 20mm dia D-type 60cm long between flanges, including brackets and fixed to walls complete all as specified and directed.
S&F "as in repair" CP Shower rose of size 150mmx150mm with swivel arm, stainless steel/CP brass, including fixing to steel pipe or union complete all as specified and directed.
S&F 20mm dia Gun metal globe or gate valves, with iron wheels head, screwed both ends for iron pipe and fixed, complete all as specified and directed.
S&F stainless steel gratings 100mm dia, with hole fixed with cement mortar, complete all as specified and directed.
S&F stainless steel gratings 100mm dia, without hole fixed with cement mortar, complete all as specified and directed.
S&F ''as in repair'' Vitreous china wash down water closet pan (pedestal pattern), white complete including fixing to trap including PVC seat cover with hinging device for pedestal pan and connecting etc, complete all as specified and directed.
S&F 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid or fixed in trenches / floors / walls, complete all as specified and directed.
S&F 110mm bore PVC (SWR) bend, plain including jointing with solvent cement, complete all as specified and directed.
S&F 100mm bore CI floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.
S&F 100mm bore CI gully/nahani trap, plain with grating including jointing with solvent cement, complete all as specified and directed.
Taking down old/broken cast iron/PVC pipes of any dia from existing lines fixed to walls with clamps or laid in trenches (incl necessary excabvation) complete all as specified and directed.
M&L 75 mm dia sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed on walls with clamps.complete all as specified and directed.
M&L 75 mm dia sand cast CI Bends with ovel access door and jointed with neat cement paste complete all as specified and directed.
M&L 75 mm dia sand cast CI cowls complete all as specified and directed.
M&L 100 mm dia sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed on walls with clamps.complete all as specified and directed.
M&L 100 mm dia sand cast CI Bends with ovel access door and jointed with neat cement paste complete all as specified and directed.
Demolition and breaking up 100mm bore drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.
Demolition and breaking up 150mm bore drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.
Excavation over area 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc.n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.
M&L for brick work with sub class ‘B’ (old size) bricks, straight or curved on plan exc 6 metre mean radius, built in CM 1:4, including demolition of old brick work complete all as specified and directed.
M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation filling & mass concrete , bed of manholes etc complete all as specified and directed.
M&L for Salt-glazed stoneware drain pipes 100mm bore laid in trenches and jointed as specified complete all as specified and directed.
M&L for Salt-glazed stoneware drain pipes 150mm bore laid in trenches and jointed as specified complete all as specified and directed.
M&L for Plain Concrete bed type C-2, 1:3:6 (using 40mm graded crushed stone aggregate)to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 100mm bore complete all as specified and directed.
M&L for Plain Concrete bed type C-2, 1:3:6 (using 40mm graded crushed stone ggregate) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm bore complete all as specified and directed.
M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as coping of masonary work including weathering slightly rounded or chamfered angles & throating complete all as specified and directed.
M&L for PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in surface channel and drains complete all as specified and directed.
Demolition of cement concrete in ground floor and pavings n. exc 15 cm thick( below or above ground level) complete including removal of debries from the site n. exc. 50m from starting point etc complete all as specified and directed.
M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates), set in CM 1:6 as in cover slabs (for manhole, drains etc.) with plain fair faces, complete all as specified and directed.
Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.
S&F TMT bars up to 12mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
M&L for mild steel round bars as in handles and runners, clamps and similar articles complete all as specified and directed.
Removing building materials etc.exc 250m but n exc 500m and deposited where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.
Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fixtures and fittings such as swithches, ceiling rose, pendants,regulators,sockets,light fittings etc and making good disturbed surfaces of walls, floors to match with existing specifications and deposited serviceable items in MES store and removing unserviceable items from the site, complete all as specified and directed.
M&L in replacement for point wiring with 1.50 sqmm in FRLS PVC insulated copper conductor cable (multistrand) PVC insulated cable in and including rigid non metallic new PVC concealed conduit terminated in new sunken pressed steel boxes of suitable size as required at site including inner and outer frame plate for any module as per site requirement mounting of modular socket/switches/fan regulators and continuous earth wire 1.5 sqmm copper cable FRLSH PVC insulated as earth wire continuity wire in green colour, controlled by one switch for one light/fan/bell point all as specified and directed. (Note :- surface conduit wiring to be done in ceiling).
All as per srl item No. 138.00 here-in-before but for 5 pin 5/6 Amps, 2 module socket on the same board complete all as specified and directed.
M&L in replacement for point wiring with 2.50 sqmm in FRLS PVC insulated copper conductor cable (multistrand) PVC insulated cable in and including rigid non metallic new PVC concealed conduit terminated in new sunken pressed steel boxes of suitable size as required at site including inner and outer frame plate for any module as per site requirement mounting of modular sockets/switches and continuous earth wire 2.5 sqmm copper cable FRLSH PVC insulated controlled connected to common earth dolly and each terminal box/fitting including cutting chases to wall making good the disturbed of surface to match with the existing specification complete (phase neutral and earth wire shall be provided in standard colour wide R, Y, B for phase black for neutral & green for earth wire wire include provide proper thimble at each joints) by one switch for one socket point all as specified and directed. (Note :- surface conduit wiring to be done in ceiling).
All as per srl item No. 140.00 here-in-before but with 4 sqmm FRLS cable insulated for 2 in 1 (6 pin) 16 amp 2 module multipurpose outlet including 4 sqmm FRLS, PVC insulated copper wire for earth continuity on independent board complete all as specified and directed.
All as per srl item No. 140.00 here-in-before but with 4 sqmm FRLS cable insulated for metal plug top geyser & AC outlet including 4 sqmm FRLS, PVC insulated copper wire for earth continuity on independent board complete all as specified and directed.
S&F in repair for 1 module Switch piano flush button, single pole, one way, 6 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.
S&F in repair for 1 module Switch piano flush button, single pole, one way, 15/16 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.
S&F in repair for 2 module Socket outlet, 6 Pin, 15/16 Amps, multipurpose, 2 in 1, flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.
S&F in repair for moduler Socket outlet, 5 Pin, 5/6 Amps, two module flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.
S&F in repair for 2 module bell push switch piano flush button, single pole, one way, 6 Amps, 240 Volts AC with polycarbonate body, complete all as specified and directed.
S&F bell ding dong type AC 230 volt single pole, complete all as specified and directed.
S&F in repair ceiling rose, surface bakelite, 2 to 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.
S&F "as in repair" of 2 module fan step regulator, step type suitable to control speed of fan from 0 to 100% in 5 to 8 step & suitable for 1200/1400mm sweep ceiling fan, hum free, 240 Volts and connecting electrically, complete all as specified and directed.
S&F "in repair" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 04 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.
S&F "in repair" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.
S&F "in repair" of 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 5 to 32 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.
S&F "in repair" of 240 volts 10KA 'C' curve miniature circuit breaker (MCB) of single poles,neutral current carrying capacity 40 to 63 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.
M&L for submain wiring with two single core FRLSH PVC insulated cable 6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked including 1x6 sqmm multistranded copper conductor FRLSH PVC green insulated unsheathed cable for earth continuity in proper thimble at each joints, including taking down existing submain wiring complete all as specified and directed. Note : Three runs of wire shall be measured as one unit.
S&F in repair lamp holder insulated body with back plate for batten fittings with polycarbonate body with and including 9 watt LED lamp retrofit type, complete all as specified and directed.
S&F in repair of surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.
S&F in repair of 1x10 Watt LED light fittings mirror type with high out put diffuser (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 10 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.
S&F of surface mounted LED Bulk Head luminaires 10/9 watts with ABS body & polycarbonate diffuser available in CCT 6000K IP 54 complete all as specified and directed.
M&L in repair of Bldg security light fittings 25 Watts, IP 65, having pressure dia cast alumn alloy housing, prismatic polycarbonate cover complete. making connection with 3 core copper flexible cable of size 23/.0076 including galvanised iron pipe medium grade bracket 0.9 mtr long of suitable dia and fixing with bldg for fixing of street light fitting complete all as specified and directed.
S&F in repair for LED luminaire 600mm x 600mm, 35/36 watt, 220 volt AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver three core flxible copper conductor case of suitable size complete all as specified and directed.
S&F in repair for LED post top lattern fitting of 1x40 Watt , IP 65 having pressure die cast alumn alloy housing, prismatic polycarbonate cover complete, making connection with 3 core copper flexible cable of size 23/0.0076 including galvanized iron pipe medium grade bracket 0.9 mtr long of suitable dia and fixing with bldg wall or pillar for fixing of street light fittings, complete all as specified and directed.
Note for srl item No 156 to 162 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.
S&F "in repair" VTPN distribution board with provision for MCCB as incommer 63A DD04 way IP 65 (for incoming MCCB & outgoing MCBs), with copper bus bar for each phase, with 2 Neutral bar, 2 Earth bar and cable ties for cable management, fully insulated bus bar & shrouded Neutral bars, with 63 Amps MCCB, 16 KA, 4 pole, as incomer and 12 Nos SP cap upto 63 Amps MCBs as outgoing complete all as specified and directed.
M&L in replacement of earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as specified and directed.
Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated multistranded, armoured heavy duty electric cable , with aluminium conductor of size 25 Sqmm x 3.5 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.
M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.
M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.
S&F in replacement of GI tubing light grade 50 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 32x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.
S&F "in replacement" MCB single pole and neutral MS sheet metal enclosure, with a two pin and earth plug and socket complete with one single pole MCB 20 Amp cpmplete all as specified and directed.
Dismantling and taking out burnt winding by cutting, cleaning slouts and re-winding of AC ceiling fan motor1200mm/1400mm of any make of fan with super enameled heat resistant copper winding wire of existing gauge & nos of turns including, sleeve work, varnishing with E class insulation, greasing, threading, connection with flexible wire 0.472 mm copper wire upto connector block and re-assembling and testing for 4 Hrs after repair complete all as specified and directed. (Repairs will be measured and paid for separately under respective items):- Notes :- (i) Fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only and repair of fan inside complex / office of GE (S) Mamun. (iii) Khaitan/RPG/KEI or equivallent make super enameled copper winding wire shall only be used. (iv) Rates are deems to be included cost of repair /servicing & replacement of minor spare part i.e. blade screws, capacitors clumps terminal connection , split pin spring washer etc.
Replacement of old unserviceable gun metal bush of ceiling fan complete all as specified and directed.
Replacement of old unserviceable capacitor AC 415 volts 2.5 mfd oil filed ISI marked complete all as specified and directed.
Replacement of old unserviceable ball bearing of suitable size as per existing make and size of ceiling fan complete all as specified and directed.
Servicing of ceiling fans of capacity 1200/1400mm including taking down from site , dismantling, cleaning, greasing/oiling of bush and bearings, replacement of set of split pins, cotter pins, blade screws, cup of both side and refixing to the existing site after servicing complete all as specified and directed. (Unserviceable parts if any will be measured and paid seperately).
Replacement of old unserviceable fan blades as per existing shape, colour and design suitable for 1200mm sweep ceiling fan of any make complete all as specified and directed.
Servicing of exhuast fans of capacity up to 300 mm including taking down from site, dismantling, cleaning, greasing/oiling of bush and bearings, replacement of outer gasket and nut & Bolts incl cleaning of outer part & fixing wall and refixing to the existing site after servicing complete all as specified and directed. (Unserviceable parts if any shall be measured seperately).
Dismantling and Re-winding of exhaust fan/industrial wall mounting fan/pedstral fan motor 250-380mm sweep any make of fan with super enameled heat resistant copper winding wire 31 SWG to 34 SWG including cutting and getting out old brunt winding, sleeve work, varnishing with E class insulation greasing, threading, connections with twin core copper flexbile wire of size 23/0.0076mm of length not more than one mtr with each fan complete all as specified and directed. Notes:- (i) Exhaust Fan/pedestal fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only. (iii) Khaitan/RPG/KEI /RR or equivallent make super enameled copper winding wire shall only be used. (iv) Exhaust fan are deems to be included cost of repair /servicing & replacement of minor spare part i.e. body screws, capacitors clumps , clips etc.
Removing old paint by scraping with sand paper including washing and filling cavaties with filter and applying two coats of painting to ceiling fan 1200-1400mm sweep at workshop with heat resistant synthetic enamel paint by spray painting incl, writing MES No on the ceiling fans as directed. Note:- Paint qaulity and colour shall be get approved from GE.
Replacement of old unserviceable outer body of ceiling fan (bottom and uper cover plate incl all fitments such screws, gasket cover canopy of both side etc complete all as specified and directed.
Replacement of existing unserviceable canopy top & bottom of ceiling fan as per existing size & shape complete all as specified and directed.
Replacement of existing unserviceable shutter and lover of exhaust fan as per existing size & shape complete all as specified and directed.
Replacement of existing unserviceable MS fan blade of exhaust fan as per existing size & shape complete all as specified and directed.
M&L for lathe work incl re-alignment to rotor, stater sloter, cleaning welding , bracing and polishing etc and refixing after repair and testing complete all as specified and directed.
M/S NARESH KUMAR SHARMA
M/S TARA CHAND CONSTRUCTION CO.
RD Engineers
Bidder Name
Abrol construction co
RD Engineers
M/S TARA CHAND CONSTRUCTION CO.
M/S NARESH KUMAR SHARMA
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .