CONSTRUCTION OF NEW MODEL DEPOT AND ACCN FOR CSD AREA DEPOT AT PALLAVARAM CANTT, CHENNAI

Amount

Lump sum price worked out by the tenderer for BUILDINGS / STRUCTURES as listed in Schedule ‘A’ Part-I

Lump sum price worked out by the tenderer for SITE CLEARANCE AND LAND DEVELOPMENT as listed in Schedule ‘A’ Part-II

Lump sum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-III

Lump sum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-IV

Lump sum price worked out by the tenderer for ROAD / PATH /CULVERT as listed in Schedule ‘A’ Part-V

Lump sum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI

Lump sum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VII

Lump sum price worked out by the tenderer for COMPOUND WALL AND GATE as listed in Schedule ‘A’ Part-VIII

Lump sum price worked out by the tenderer for RAIN WATER HARVESTING as listed in Schedule ‘A’ Part-IX

Lump sum price worked out by the tenderer for RETAINING WALL as listed in Schedule ‘A’ Part-X

Lump sum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-XI

Lump sum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-XII

Lump sum price worked out by the tenderer for COOLING APPLIANCES as listed in Schedule ‘A’ Part-XIII

Lump sum price worked out by the tenderer for LIGHTENING PROTECTION SYSTEM as listed in Schedule ‘A’ Part-XIV

Lump sum price worked out by the tenderer for FIRE FIGHTING SYSTEM as listed in Schedule ‘A’ Part-XV

Lump sum price worked out by the tenderer for DEMOLITION/ DISMANTLING as listed in Schedule ‘A’ Part-XVI

Note: Schedule 'A' part XVII to XX are not pre-priced by MES and the pre-priced rate indicated as "Blank" under column 5 signifies this fact only.

SCHEDULE 'A' PART XVII (LIFT)

Design, supply, install, testing & commissioning goods lift Speed 1 metre/Sec with single speed motor, 415 volts, 3 phase AC 50 Hz supply, conforming to IS-14665 and as amended, suitable to serve G + 2 upper floors with AC variable voltage & variable frequency drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening door with door drive (electric motor driven mechanism ) sliding stainless steel door, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set 3 nos, one each in car, machine room & near ground floor landing door) for 2000 KG complete all as per Item No 1 of SCHEDULE 'A' Part XVII.

SCHEDULE 'A' PART XVIII (DIESEL GENERATOR SET 500KVA)

Supplying, installing, testing and commissioning of Diesel Engine driven generating set, fully wired alternator AC to give an output of 500 KVA continuously rating at a PF of 0.8 lagging, 415 volts, AC 3 phase 4 wire 50 HZ, 1500 RPM, directly coupled with diesel engine water cooled mounted on common base frame complete with floor mounting fuel tank (service tank) of adequate capacity with fuel line & accessories, PCC foundation work as per manufacturer's instructions, vibration damper pads & other accessories etc. complete all as per Item No 1 of SCHEDULE 'A' Part XVIII.

SCHEDULE 'A' PART XIX (RMG UNIT AND COMPACT SUBSTATION)

Supply and installation of RMG unit, HT 11 KV, 3 phase, 50 Hz, 630Amps totally enclosed metal clad switchgear complete with, 500 KVA metering system, One No Vacuum circuit breaker having rupturing capacity 350 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 630 Amp and two Nos LBS complete all as specified and directed complete all as per Item No 01 of SCHEDULE 'A' Part XIX.

Supply, installation, testing, commission of out door type non walk in compact sub station suitable for 11 KV/433 volts complete all as per Item No 02 of SCHEDULE 'A' Part XIX.

SCHEDULE 'A' PART XX (MISCELLANEOUS ITEMS)

SITE CLEARANCE AND LAND DEVELOPMENT

Supply only approved earth from out side MoD land for filling under floors, returning filling in and filling in low lying area etc., complete all as specified and as directed.

INTERNAL WATER SUPPLY

Supply and fix two way bib cock double handle 15mm bore, cast copper alloy, chromium plated with wall flange, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

INTERNAL ELECTRIC SUPPLY

Supply and Fix modular type MCB, SP, 16-32 Amps, 1 module conforming to IS 60898- 1: 2002 all as per Cat No. 6759 74 of Legrand or technocommercially equivalent of other specified makes complete all as specified and as directed.

Supply and fix modular socket 25 Amps/32 Amps, 3 pin, 230 Volts, 2 modules, flush type universal shuttered type conforming to IS 1293: 2005 all as per Cat No.5734 66 of Legrand or technocommercially equivalent of other specified makes complete all as specified and as directed.

Supply and Fix modular TV Co-Axial socket, 1 module all as per Cat No. 5734 25 of Legrand or technocommercially equivalent of other specified makes complete all as specified and as directed.

Supply and Fix modular Telephone socket RJ 11 with shutter, 1 module all as per Cat No. 5734 26 of Legrand or technocommercially equivalent of other specified makes complete all as specified and as directed.

BLANK

Supply & Fix vertical triple pole & neutral, double door, 4 way, metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for MCCB up to 250 A as incomer and SP/TP MCBs as outgoing, reversible metal door, fully insulated 250 A copper busbar for each phase, two fully insulated & shrouded neutral bars, two earthbars, cable ties for cable management, prefitted masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and as directed. NOTES: MCCBs and MCBs shall be measured and paid separately.

Supply and Fix Three Phase Electronic energy meter of Class 1.0 accuracy, 4 Wire static direct connected watthour Smart meter, having power consumption conforming to IS 16444-1:2015, rated voltage 3 X 240 V (P-N), voltage variaton -40% to +20%, current rating 10 to 100 A, starting current 0.2% of basic current, accuracy up to 120% of maximum current, frequency 50 Hz, frequency variation -5% to +5%, IP 51 protection to measure instanteneous phase-wise voltages, phase-wise currents, system power factor, active power, reactive power and apparent power, frequency, 4 quadrant measurement of kWh, kVArh and kVAh, maximum demand (kW and kVA along with date and time), having 8 digit backlit LCD display, LED indication for relay status and tampers, auto scroll, communication options including optical, RF and GPRS, Load connection/disconnection via relays in phase and neutral, Data logging for instantaneous parameters, billing parameters and enery backups, push buttton and high resolution display modes, pulse LEDs for kWh and kVArh etc. complete all as specified and as directed.

Supply and fix Single Phase Electronic energy meter of Class 1.0 accuracy, 2 Wire static direct connected watthour smart meter, having power consumption conforming to IS 16444-1:2015, rated voltage 3 X 240 V (P-N), voltage variaton -40% to +20%, current rating 10 to 60 A, starting current 0.2% of basic current, accuracy up to 120% of maximum current, frequency 50 Hz, frequency variation -5% to +5%, IP 51 protection to measure instanteneous voltage, phase and neutral current, power factor, active power, reactive power and apparent power, frequency, 4 quadrant measurement of kWh, kVArh and kVAh, maximum demand (kW and kVA along with date and time), having 8 digit backlit LCD display, LED indication for relay status and tampers, auto scroll, communication options including optical, RF and GPRS, Load connection/disconnection via relays in phase and neutral, Data logging for instantaneous parameters, billing parameters and enery backups, push buttton and high resolution display modes, pulse LEDs for kWh and kVArh etc., complete all as specified and directed.

Notes for BOQ Items No.29 & 30:- (i) The meter should be fixed on suitable size sheet metal enclosure on existing wall having openable outer door/locking arrangement with incoming/outgoing cable entry all as directed. (ii) The unit rate quoted shall be deemed to include the cost of sheet metal enclosure for energy meter .

Supply and fix 20/22 Watts surface/wall mounted LED batten capable of delivering 2000 lumen, having PC diffuser, luminous efficacy of > 90 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing, white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input frequency 50- 60 Hz all as per Cat No. BN021C LED22S PSU CW GR of Philips or technocommercially equivalent of other specified makes including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.

Supply and fix 10/12 Watts surface / wall mounted LED batten capable of delivering 1150 lumen, having PC diffuser, luminous efficacy of > 110 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing. white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input frequency 50- 60 Hz, all as per Cat No. BN 021 LED 12S 6500 PSU GR of Philips or technocommercially equivalent of other specified makes including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.

Supply and fix 5 Watts, 3-star (EEL) T-shape lamp capable delivering 800 lumen having luminous efficacy of > 100 lm/W, starting time < 0.5 s, CRI > 80, CCT 6500K, PF >0.9, input voltage range 140- 270 V, input frequency 50- 60 Hz with B22 base all as per Cat No. T- Bulb CW 5W B22 of Philips or technocommercially equivalent of other specified makes complete all as specified and directed.

Supply and fix 10 Watts, 3-star (EEL) T-shape lamp capable delivering 1000 lumen having luminous efficacy of > 100 lm/W, starting time < 0.5 s, CRI > 80, CCT 6500K, PF >0.9, input voltage range 140- 270 V, input frequency 50- 60 Hz and B22 base all as per Cat No. T- Bulb CW 10W B22 of Philips or technocommercially equivalent of other specified makes complete all as specified and directed.

Supply and fix 7.5 Watts decorative, wall mounting, chrome finish fixture with opal glass diffuser suitable A60 LED filament lamp with E27 base all as per Cat No. LHFOAJD1TZ1C060 of Havells or technocommercially equivalent of other specified makes complete all as specified and directed.

Supply and fix of 12 Watts surface mounted round shape LED downlight capable of delivering 1200 lumen. having minimum luminous efficiency > 100 lumen/W, CCT 6500K, CRI > 80, high quality polycarbonate diffuser, input voltage range 140- 270 V, input frequency 50- 60 Hz all as per Cat No.SM250C LED12S- 6500 PSU WH of Philips or technocommercially equivalent of other specified makes complete all as specified and directed.

Supply and fix 100 Watts High bay light duranto mounted LED, extruded aluminium housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI ≥ 80, power factor ≥ 0.95, system luminous efficacy > 100, having average life 50000 hrs, operating voltage 140- 270 all as per Cat No. BY225P LED100S CW NB PSU FG GR V1 of Philips or technocommercially equivalent of other specified makes including electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to the LED fitting and hanging arrangements from ceiling with SS chain 2 meter height complete all as specified and directed.

Supply and fix 25 W street light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 2600 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting all as per Cat No. BRP042 P LED25 CW SLE S1PSU GR P4210 of Philips or technocommercially equivalent of other specified makes with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and as directed.

ROAD/PATH/CULVERT

Material and labour for preparing bituminous surfaces of road and marking centre lines, stop lines, dashes, arrows etc. and the like on roads pavements with hot applied thermo plastic compound 2.5mm thick of white, golden, yellow or black colour as required and confirming to BS 3262-1989 including reflectorising glass bead @ 0.25 Kg/Sqm as per IRC:35(1997) and as per Clause 803 of MORTH specification with special applicator machine fitted with profile shoe, glass beads dispenser propane tank heater and profile shoe heater with heating arrangement up to 160°C, driven by experienced operator all as per manufacturers' instruction etc., complete all as specified and as directed.

Solar road delineator 6 LEDs of colour red/yellow housed in plastic body, LEDs, solarcells, battery and light sensor well protected inside polycarbonate sheet and protected with powder coated wire mesh cage, mounted over 47/50 mm dia steel tube powder coated of length 900 mm having sheet foot for firm grip to ground all as per Cat- Part No. GPL-13-01 of GREENLITE or DA-112 of Darkeye or technocommercially equivalent of other specified makes including cutting holes in road of size 400X400X600mm and embedded in PCC 1:2:4 type B1 (using 20mm graded aggregate) grouting etc., complete all as specified and as directed.

Material and labour for framed work as in sign board using angle or other section with gusset plates, rails, baces etc., complete drilled for fixing steel sheeting or other covering etc., to be prepared for hanging or sliding including either hooks and hinges or steel hangings door fitting and hanging, also fastening and fixing, confirming to gde Fe-410-S/ Fe-290 E 165 etc., complete all as specified and as directed.

Material and labour for index hands (Natural size) or arrows (upto 40cm long) fixed all as specified and as directed .

Supply and fix of Radium reflecting sticker of approved colour pasted over MS sheet plate with suitable adhesive for sign board, road side singal etc., all as specified and as directed .

Supply and fix Radium sticker of Size of letters exc 5cm but n exc 7.5cm high, of approved color cut into shape as in letter or figers (Block, Roman, Italic or Indian) of following size and pasted over radium sticker back ground, all as per manufacture's instruction and as directed. Note: The rate quoted shall be deemed to include the cutting and wastages.

Supply and fix Speed bump of size 350mm x 500mm x 50mm, Yellow and black colour made of ABS plate/HDPE material, highly reflective reflectors mould in PMMA material welded with ABS plate through ultrasonic welding process etc, all as per Cat No. DA-1009 of Darkeye or technocommercially equivalent of other specified makes to withstand 40 ton load capacity on road including epoxi for fixing bump on road at different places with necessary bolts/nuts etc, complete all as specified and as directed .

EXTERNAL WATER SUPPLY

Material and Labour for Construction of valve chamber of internal size 1000mm x 1000mm x 900mm including necessary earth work excavation, 100mm thick PCC 1:4:8, type D2 using 40mm graded stone aggregate in foundation with 100mm offset, 200mm thick PCC solid block masonry walls built in CM 1:6, PCC 1:2:4 type B1 for coping, 15mm thick rendering in CM 1:4 for internal surfaces and external plaster up to a depth of 15cm below GL, including provision of 3.0mm thick MS sheet cover, double door, welded to 50 mm x 50 mm x 6mm MS angle frame fixed with hold fasts in PCC 1:2:4 type B1, 20mm x 6mm flat iron hinges with locking arrangement including lock sixty five mm, brassd and keys(Godrej/Shell), MS handles and applying two coats of synthetic eanmel paint over a coat of red oxide zinc chrome primer to all steel surfaces including excavation & earth work in any kind of soil /soft disintegrated rock and disposal of surplus soil to a distance not exceeding 50 metre complete all as specified and as directed.

Material and Labour for Construction of valve chamber of internal size 900mm x 900mm x 600mm including necessary earth work excavation, 100mm thick PCC 1:4:8, type D2 using 40mm graded stone aggregate in foundation with 100mm offset, 200mm thick PCC solid block masonry walls built in CM 1:6, PCC 1:2:4 type B1 for coping, 15mm thick rendering in CM 1:4 for internal surfaces and external plaster up to a depth of 15cm below GL, including provision of 3.0mm thick MS sheet cover, double door, welded to 50 mm x 50 mm x 6mm MS angle frame fixed with hold fasts in PCC 1:2:4 type B1, 20mm x 6mm flat iron hinges with locking arrangement including lock sixty five mm, brassd and keys(Godrej/Shell), MS handles and applying two coats of synthetic eanmel paint over a coat of red oxide zinc chrome primer to all steel surfaces including excavation & earth work in any kind of soil /soft disintegrated rock and disposal of surplus soil to a distance not exceeding 50 metre complete all as specified and as directed.

Material and labour for road crossing/drain crossing by adopting trenchless tunneling work through specified pipe jacking method by erecting the equipment to true to the alignment and gradient by hydraulic pipe jacking technique complete including tunneling, excavation in any type of soils, hard rock etc., including provision of HDPE pipe heavy duty of size 150 mm dia as casing pipe in any length with jointing materials, inserting 100mm bore GI tubing, medium grade with Horizontal Directional Drilling (HDD) technique to a depth not less than 2m below the ground level from starting point to end point, necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorities etc., complete all as specified and as directed. Note : - (i) GI pipe medium grade 100mm will be measured and paid seperately under relevant item as supply only. (ii) The unit rate quoted shall be deemed to include the cost of 150mm dia heavy duty HDPE pipe, Earthwork and excavation in any type of soil for erecting the equipment.

Supply, install, testing and commisioning of monoblock openwell horizontal submersible pump set suitablle for discharge cap 6.94 lps, 60M head, electric driven 415 V, 50 Hz including provision of suitable size and length of PVC insulated and PVC sheathed, Flat Three Core copper conductor cable for Submersible Pump Motors, making connection from starter panel to pump motor inside UG Sump etc., complete all as specified and as directed.

Supply and installation and testing chemical dosing system suitable to inject solution up to 25 LPH comprising dosing pump coupled with three phase electric motor of capacity 0.5 HP, 1440 RPM assembly with agitator in one motor agitator with ss sweep blade duly FRP coated, FRP tank 150 litr capacity complete unit mounted on heavy duty with MS fabricated frame duly anti corrisive paint complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Supply and Fix Hot dip galvanised Pole top mounting bracket of Swan Neck type duly bended to shape, single arm fabricated with GI pipe medim grade 50 mm dia of minimum height of 1mtr and suitable size top cap supporting piece with top canopy protruding atleast 15 cm in all sides as directed and fixed complete on top of steel tubular poles with bolts and nuts including painting with primer and silver paint complete all as specified and directed

Supply and fix LED Street light fitting 60W capacity ENDURA OMNIPLUS new geration energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with hih efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistantance of IK07 complete all as per Cat No.ENDURAOMNIPLUSSL60WLED757SASYTOPC of Havells or technocommercially equivalent of other specified makes including necessary service connection with 2.5sqmmm copper cable duly drawn through 20mm PVC conduit, clamping etc from MCB control box complete all as specified and directed.

Supply and fix LED Street light fitting 30W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having bottom opening seperate driver compartment with IP66 protection and impact resistance of IK08 all as per Cat No.ENDURASUNDOWNSL30WLED757 PASYBOPC of Havells or technocommercially equivalent of other specified makes including necessary service connection with 2.5sqmmm copper cable duly drawn through 20mm PVC conduit, clamping etc from MCB control box complete all as specified and as directed.

Supply and fix LED Flood light fitting 60W, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting all as per CAt No. JETAALBAFLOODLIGHT60W of Havells or technocommercially equivalent of other specified makes including necessary fixing of fitting on pole with clamps, nuts bolts and necessary service connection with 2.5sqmmm copper cable duly drawn through 20mm PVC conduit, clamping etc from MCB control box complete all as specified and as directed.

Supply and fix pole mounted PVC Box weather proof type with hinged type door off white color of size 240x130x110 mm comprising of busbar 3 Nos, 2 Nos. MCB 6A and 1 No. neutral link, fixed on pole with suitable clamps, bolts and nuts complete all as specified and as directed.

Supply and installation, testing and commisioning factory made outdoor cubical type LT panel board dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For Main Outdoor Panel)

Supply and installation, testing and commisioning factory made outdoor LT Feeder pillar Box dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For storage Bldg A1 and A2)

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder pillar box dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For storage Bldg B1 and B2)

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder Pillar Box , dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For Admin Building)

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder Pillar Box,dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed:- (For Storage Bldg B3 and A3 )

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder Pillar Box , dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed (For Storage Building C1 & C2)

Supply, Fabricate, install, connect, test and commission LT panel Board Indoor type totally enclosed, compartmentalised for each switch gear, powder coated, weather and vermin/weather proof,1100 volts, 50Hz, AC supply, factory made fully compartmentalised made out of 2 mm thick CRCA sheet steel for load enclosure IP 54 as per IS 8623 complete including suitable angle iron/flat iron frame work/ supports, base support MS channel ISMC 75 etc., as required with and including the following supplied fitted and connected internally complete:, 3 phase, 4 wire, 415 / 500 V, 50 Hz, bottom with detachable plates,front and rear with hinged type door and locking arrangements, chamber for copper bus bars, chamber for cable on both side, louvers and air vent for natural air flow, holes drilled for connections, separate chamber for metering equipment and each switch gears complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated, complete mounted on MS channel ISMC 75 complete all as specified and comprising of the followings. (For Water Supply Pump house)

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder Pillar Box,dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For Residential Side)

Supply and installation, testing and commisioning factory made outdoor cubical type LT Feeder Pillar Box,dust and vermin proof, compartmetalised mounted on and including PCC 1:3:6 foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and fabricated made out of 3.15mm thick MS sheet over MS 50x50x6mm thick angle iron of required type for support double door both side open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint complete and having separate doors inside including following incoming/outgoing feeders all as specified and as directed. (For Residential side)

Notes for BOQ Items No 56 to 64:- (i) Panel front side should have the conventional skull & bone sign board for 440V LT (ii) The unit rate quoted shall be deemed to include the cost of Providing necessary PCC foundation/making connection for incoming and outgoing cables with suitable aluminium lugs, cable glands etc., (iii) The unit rate quoted shall be deemed to include the cost of necessary marking of Incoing/Outgoing MCCBs termination/MCBs withdigital stickering as directed.

Supply and Fix Cable route indicators for HT Cables duly embosed "HT CABLE" on oval shape 200x150x6mm cast iron top fixed on 25x25xx6mm angle iron leg duly painted and grouted in PCC 1:3:6 type C1 along the path of laid cable including necessary excavation and PCC work complete all as specified and as directed.

Supply and Fix Cable route indicators for LT Cables duly embosed "LT CABLE" on oval shape 200x150x6mm cast iron top fixed on 25x25xx6mm angle iron leg duly painted and grouted in PCC 1:3:6 type C1 along the path of laid cable including necessary excavation and PCC work complete all as specified and as directed.

Supply and fix Post Top Lantern with 50Watts LED Lamp, suitable for fixed on 76mm dia pipe Aesthetically designed IP 65, LED post top with aluminium enclosure, powered with high power LEDs as light source and die casted heat sink exhibits classic Victorian look with symmetrical light distribution and excellent heat dissipation for long life all as per Cat No.JUPITERMAXIPT50WLED 830PSYMTOPC of Havells or technocommercially equivalent of other specified make including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size complete all as specified and as directed.

Labour only for lay / spread in trenches old sand obtained from trenches while excavation and sieving the same including cleaning, spreading, levellng, punning for cushioning of cable to the full width of excavated trench, 8cm thick before laying cable and 15cm thick above the cable, gently punned down complete all as specified and as directed. Note : Punned thickness only will be considered or payment.

Material and labour for Trenchless boring horizontaly underneath the existing bituminous macadam road/drain crosswise by adopting trenchless tunneling work through specified pipe jacking method by erecting the equipment to true to the alignment and gradient by hydraulic pipe jacking technique complete including tunneling, excavation in any type of soils, hard rock etc., including GI tubing, 100mm dia medium grade of any length with all fittings, socket welded and inserting it into the trenchless boring to carry LT UG cables of size upto 400 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorities etc., complete all as specified and as directed. Note: (i) Supply only GI tubing 100mm dia medium grade shall be measured and paid separately under relevant item and Schedule

Supply and fix HDPE pipe heavy duty 100mm dia for road/plinth cross purpose omplete all as specified and as directed.

Supply only Electrical insulation rubber mate 1100V grade of size 1000mm x 2000mm, 9mm thickness conforming to IS 15652 for pump house/machineries installations complete all as specified and as directed.

COOLING APPLIANCES

Supply and fix Voltage stabiliser for automatic operation single phase naturally air cooled indoor flame proof type & designed for input variation between 170 V to 250 V with outpur voltage stabilised at 230 volts with accuracy of + 2.5 % and of capacity 1 KVA complete all as specified and as directed.

Supply, fix, connect, test and commission water purifier, water flow rate 200 LPH, water pressure minimum 0.4 kg/sqcm, maximum 2 kg/sqcm, with UL lamp 20 watts, power rating 35 watts, overall dimension 355x102x300mm all as per Model Aqua Guard-200 of Eureka Forbes or technocommercially equivalent of other specified makes including connecting up the water cooler with PVC flexible water tubing and testing proper function complete all as specified and as directed.

Supply and fix Voltage stabiliser for automatic operation single phase naturally air cooled indoor and designed for input variation between 170 V to 250 V with outpur voltage stabilised at 230 volts with accuracy of + 2.5 % and of capacity 5 KVA

FIRE FIGHTING SYSTEM

Material and Labour for low smoke zero halogen (LS0H) fire survival control cable with circuit integrity, conforming to BS 7846 and rated for 600 V, having plain annealed stranded copper conductor with fire-resistant mica tapes covered by an extruded layer of cross-linked polyethylene, extruded layer of thermoplastic low smoke zero halogen (LS0H) compound, single layer of galvanized steel wires and thermoplastic LS0H compound sheath, suitable for operating temperature range -40 ˚C to +90 ˚C and minimum bending radius being 12 times the overall cable diameter, including laying, clamping, termination and ferruling complete all as specified and as directed of following sizes:-

a) 2 core x 2.5 Sqmm

b) 3 core x 2.5 Sqmm

c) 12 core x 2.5 Sqmm

Material & Labour for 1.1 kV grade copper conductor, XLPE insulated armoured cable conforming to IS 7098-1: 1988, having stranded aluminium compact shaped conductors as per Cl. 2 of IS 8130: 1984, PVC inner sheath, single armouring of galvanised steel strip/wire and PVC Type ST-2 outer sheath conforming to IS 5831: 1984, including necessary clamping / dressing with cable ties and termination complete all as specified and as directed of following sizes:-

a) 3 core x 35 Sqmm

b) 3 core x 6 Sqmm

Material and Labour for PN 1.6 rated 200 mm NB polypropelene vortex inhibitor suction lift, conforming to BS 4504 with stainless wire mesh, bolts, nuts and washers, etc. complete all as specified and as directed. Make: Associated Enterprises, Enduramaxx, Balmoral Tanks

Supply, installation, testing and commissioning of FM approved and UL listed Network Control Display (NCD) / Repeater Panel capable of full supervision of all inputs and network integrity, having 10" high definition 1024 X 600 colour touchscreen display, environmental adjustment controls to maximize LCD legibility, LED status indicators (for power supply and off normal condition), network connection, three USB connections, trouble relay, tamper and trouble inputs, etc. and features viz. network-wide acknowledge silence, reset, lamp test, fully programmable node-mapping subsystem, colour coded icon based event notification, event vectoring, etc. along with UL listed non-resettable 24 VDC power source complete all as specified and as directed. Make: Notifier NCD or equivalent model of JC, Esser

Material & Labour for low smoke zero halogen (LS0H) flame retardant fire alarm cable, conforming to BS 7629-1, BS 6387 & BS EN 50200 and rated for 500 V, drawn through concealed PVC conduit and having plain annealed stranded copper conductor with primary insulation of glass mica fire resistant tape and secondary insulation of high performance silicone rubber, earth/drain wire of annealed tinned copper, electrostatic screen of aluminium fire barrier and type LTS3 outer sheath conforming to BS 7655, suitable for operating temperature range -30 ˚C to +70 ˚C and minimum bending radius being 6 times the overall cable diameter, RED in colour, including laying, termination and ferruling complete all as specified and as directed of following sizes:-. Make: RR Kabel, Polycab, Havells

a) 2 core x 1.5 Sqmm

b) 2 core x 2.5 Sqmm

Supply & Fix of CL#150 rated two-piece design 25 mm NB Cast iron (CI) Straight pattern ball valve, conforming to IS 9890: 1981 and tested as per BS 6755-1, having Cast iron body, Stainless steel AISI 304 ball, renewable PTFE seat & gland packing, CS fastners & lever having screwed / socket weld end connection with accessories complete all as specified and as directed. Make: Leader, Sant, Venus,Tyco-Grinnell, Zoloto, RB

Supply & Fix of orifice plate made out of 6 mm thick SS 304 with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete all as specified and as directed.. Make: Newage, AAAG, Minimax

Material & Labour for FM approved and UL listed, PN 1.6 rated lever operated, wafer type CI butterfly valve, conforming to IS 13095: 1991, fitted with visual indicator & temper switch, having Cast iron (CI) body with ductile iron EPDM coated disc, SS431 stub shaft, PTFE bushing, flange drilling standard end connection conforming to IS: 1538- 1993 along with necessary accessories complete all as specified and as directed of following sizes for Zone control valve assembly. Make:Grinell-Tyco, Nibbco, BK valve, Kartar valves

a) 100 mm NB

b) 80 mm NB

Material & Labour for FM approved and UL listed 25 mm NB compact 3 position ball valve with drain orifice (test and drain valve) to test and drain water flow through sprinkler systems having OFF-TEST-DRAIN position, integral sight glass, rated pressure 300 psi, orifice size 15 mm and K factor 5.6, conforming to NFPA 13, along with necessary accessories complete all as specified and as directed. Make: Tyco, HD, Viking

Supply & Fix of 3 kg light-weight squeeze grip CO2 type fire extinguisher, conforming to IS 15683: 2006, with CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel with wheel type valve, discharge nozzle, bend & horn, wall mounting bracket / floor trolley mounting accessories along with suitable signage complete all as specified and as directed. Make: Kanex, Minimax, Aim-EX, Safeguard, coffco, Variex NOTES: [i] Test Pressure: 250 kgf / Sq. cm [ii] Operating temperature : -300C to + 550C [iii] Locking pin and wire seal should be provided to indicate that the extinguisher has not been use. [iv] Every Extinguisher should be supplied with an operating manual.

Supply & Fix 4 kg capacity dry chemical powder (ABC) type fire extinguisher, conforming to IS 15683: 2006, with initial filling in brand new cylinder with powder coated finish, fitted in gunmetal union, high pressure CO2 gas cartridge, discharge hose, wall mounting bracket / floor trolley mounting accessories along with suitable signage, etc. complete all as specified and as directed. Make: Kanex, Minimax, Aim-EX, Safeguard, coffco, Variex NOTES: [i] Operating temperature : -300C to + 550C "[ii] Performance criteria : Discharge time not less than 45 sec , throw not less than 4 meters" [iii] Hydro test and burst pressure test : Shall pass hydro test pressure of 35 bars 2.5 minutes and with stand a burst pressure of 55 bar

Supply & Fix Galvanized mild steel set of Fire bucket (4 Nos) conforming to IS 2546: 1974 round bottom type enamel painted, white inside & Red out side and Letter "FIRE" in black out side and handle with mounting bracket & stand complete all as specified and as directed. Make: Star safety solution, Mark safety appliances

Supply & Fix of Signage having size 300 mm X 150 mm reading "EXIT" in 12.5 mm block letters in Green and white background, self illuminated properly spaced to provide good legibility located directly in corridor near to each staircase and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level.These lights shall emit the maximum light required even during the electricity supply or in Black out period with high energy efficiency manufactured using superior quality Aluminium Extrusion body raw material complete all as specified and as directed. Make: Variex, Mr safe, Matrix sign lab EXIT Signage shall meet the following technical / operational requirements: [i] Product Material: Alluminium ALLOY Extrusion [ii] Product Finish:- Matt Black / Snow white finish after phosphochromate treatment [iii] Wattage:- 5 Watt [iv] Mounting: Surface / Hanging

Supply & Fix of Signage having size of 500 mm X 500 mm, indicating the "Floor Number" in bold type and at 75 mm high numerals in red and white background, made out of 3 mm thick opaque PVC foam board with computer cut, PVC non-reflective self adhesive vinyle painted foam board, posted and maintained within each stair enclosure on every floor, securely attached to the stair side of the door in a way that the bottom of the sign is not above 1.5 m from the finished floor level complete all as specified and as directed. Make: Variex, Mr safe, Matrix sign lab

Supply & Fix of Signage having size of 450 MM X 150 MM reading "FIRE EXTINGUISHER" in 12.5 mm block letters in White and Red background, made out of 3 mm thick opaque PVC foam board with computer cut, PVC non-reflective self adhesive vinyle painted foam board,properly spaced to provide good legibility located directly in corridor near to each Manual call point/Fire Extinguisher and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level complete all as specified and as directed. Make: Variex, Mr safe, Matrix sign lab

Supply & Fix of Signage having size of 150 mm X 600 mm, posted and maintained at each lift landing and on the side of the stairway door from which egress is to be made on every floor, indicating the "STAIRCASE" by an alphabetical letter in bold type and at 75 mm high letters in red and white background, made out of 3 mm thick opaque PVC foam board with computer cut, PVC non-reflective self adhesive vinyle painted foam board,securely attached to the side of the stairway door from which egress is to be made in a way that the bottom of the sign is not above 1.5 m from the finished floor level complete all as specified and as directed. Make: Variex, Mr safe, Matrix sign lab

Supply and fix Carbon-dioxide type fire extinguisher of 3 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge Nozzle, bend & horn, wall mounting bracket /floor trolley mounting accessories with suitable signage's complete, confirming to IS: 2878 complete all as specified and as directed. Make: Safex/Newage/Ceasefire

Material & Labour for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanised strip of size 32 mm x 6 mm as earth lead, by means of bolts, buts, check nuts and washers of galvanised iron or steel, galvanized iron pipe of 40 mm diameter, connected to earthing test point, all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion and including excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep, with a 10 mm thick CI cover, hinged to CI frame on ground level, GI watering pipe, funnel, etc. as all specified and directed.

Material & Labour for earthing complete with galvanized steel earth plate electrode of 60 cm X 60 cm X 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized strip of size 25 mm X 4 mm as earth lead by means of bolts, nuts, checknuts and washers of galvanized iron or steel, galvanized iron pipe of 40 mm diameter connected to earthing test point, all as shown in electrical plate No. 5, connected to earthing test point including testing on completion, excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep with a 10 mm deep CI cover hinged to CI frame on ground level, GI watering pipe, funnel, etc. complete all as specified and as directed.

M&L for earthing complete using GI wire as earthing lead complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not les than 2.25meters deep below ground level with top edge of the plate not less than 1.5m below normal ground level connected to galvanised iron as earthing 4mm dia by means of bolts, nuts, check nuts and washers complete all as shown in Electrical Plate No 3 and connected to earthing test point including testing on completion, excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep with a 10 mm deep CI cover hinged to CI frame on ground level, GI watering pipe, funnel, etc. complete all as specified and as directed.

NJR Constructions Private Limited

ABIRAMI ENGINEERING CONSTRUCTION & CO

Silpa Projects & Infrastructure (I) Pvt Ltd

SARAOGI BUILDERS LIMITED

Jatan Constructions Private Limited

BNR Infrastructure Projects Private Limited

PUSHKARRAJ CONSTRUCTION PRIVATE LIMITED

Rds Project ltd.

Som Projects Pvt Ltd

KEC International Limited

RPP Infra Projects Limited

SRI VENKATACHALAPATHY CONSTRUCTIONS PRIVATE LIMITED