MAIN POWER PLANT (MPP) EPC PACKAGE FOR DURGAPUR THERMAL POWER STATION (1X800MW)

TOTAL OF SCHEDULE NO.1 Main Equipment (In INR) CIF Price of Main Equipment Excluding Type Test charges to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Main Equipment (In Foreign Currency 1 i.e. USD) CIF Price of Main Equipment Excluding Type Test charges to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Main Equipment (In Foreign Currency 2 i.e. EUR) CIF Price of Main Equipment Excluding Type Test charges to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Main Equipment (In Foreign Currency 3 i.e. JPY) CIF Price of Main Equipment Excluding Type Test charges to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Mandatory Spares (In INR) CIF Price of Mandatory Spares to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Mandatory Spares (In Foreign Currency 1 i.e. USD) CIF Price of Mandatory Spares to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Mandatory Spares (In Foreign Currency 2 i.e. EUR) CIF Price of Mandatory Spares to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Mandatory Spares (In Foreign Currency 3 i.e. JPY) CIF Price of Mandatory Spares to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Type Test Charges (In INR) Type Test Charges for Plant and Equipment to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Type Test Charges (In Foreign Currency 1 i.e. USD) Type Test Charges for Plant and Equipment to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Type Test Charges (In Foreign Currency 2 i.e. EUR) Type Test Charges for Plant and Equipment to be supplied from Abroad.

TOTAL OF SCHEDULE NO.1 Type Test Charges (In Foreign Currency 3 i.e. JPY) Type Test Charges for Plant and Equipment to be supplied from Abroad.

TOTAL OF SCHEDULE NO.2 Main Equipment (In INR) Ex-works Price of Main Equipment Excluding Type Test charges to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Main Equipment (In Foreign Currency 1 i.e. USD) Ex-works Price of Main Equipment Excluding Type Test charges to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Main Equipment (In Foreign Currency 2 i.e. EUR) Ex-works Price of Main Equipment Excluding Type Test charges to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Main Equipment (In Foreign Currency 3 i.e. JPY) Ex-works Price of Main Equipment Excluding Type Test charges to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Mandatory Spares (In INR) Ex-works Price of Mandatory Spares to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Mandatory Spares (In Foreign Currency 1 i.e. USD) Ex-works Price of Mandatory Spares to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Mandatory Spares (In Foreign Currency 2 i.e. EUR) Ex-works Price of Mandatory Spares to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Mandatory Spares (In Foreign Currency 3 i.e. JPY) Ex-works Price of Mandatory Spares to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Type Test Charges (In INR) Type Test Charges for Plant and Equipment to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Type Test Charges (In Foreign Currency 1 i.e. USD) Type Test Charges for Plant and Equipment to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Type Test Charges (In Foreign Currency 2 i.e. EUR) Type Test Charges for Plant and Equipment to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.2 Type Test Charges (In Foreign Currency 3 i.e. JPY) Type Test Charges for Plant and Equipment to be supplied from Employer's Country.

TOTAL OF SCHEDULE NO.3 (In INR) Local Transportation including Port Handling, Port Clearance, custom reconciliation & inland transit insurance and other local costs incidental to delivery of Main Equipment.

TOTAL OF SCHEDULE NO.3 (In INR) Local Transportation including Port Handling, Port Clearance, custom reconciliation & inland transit insurance and other local costs incidental to delivery of Mandatory Spares.

TOTAL OF SCHEDULE NO.4 (In INR) Installation Services including Erection, Testing & commissioning works, Insurance covers other than inland transit insurance and other services and Civil works Price.

TOTAL OF SCHEDULE NO.4 (In Foreign Currency 1 i.e. USD) Installation Services including Erection, Testing & commissioning works, Insurance covers other than inland transit insurance and other services and Civil works Price.

TOTAL OF SCHEDULE NO.4 (In Foreign Currency 2 i.e. EUR) Installation Services including Erection, Testing & commissioning works, Insurance covers other than inland transit insurance and other services and Civil works Price.

TOTAL OF SCHEDULE NO.4 (In Foreign Currency 3 i.e. JPY) Installation Services including Erection, Testing & commissioning works, Insurance covers other than inland transit insurance and other services and Civil works Price.

TOTAL OF SCHEDULE NO.7B (In INR) Goods and Services Tax (GST), applicable on Schedules - 2,3 & 4 not included in bid price.

TOTAL OF SCHEDULE NO.7B (In Foreign Currency 1 i.e. USD) Goods and Services Tax (GST), applicable on Schedules - 2,3 & 4 not included in bid price.

TOTAL OF SCHEDULE NO.7B (In Foreign Currency 2 i.e. EUR) Goods and Services Tax (GST), applicable on Schedules - 2,3 & 4 not included in bid price.

TOTAL OF SCHEDULE NO.7B (In Foreign Currency 3 i.e. JPY) Goods and Services Tax (GST), applicable on Schedules - 2,3 & 4 not included in bid price.

TOTAL OF SCHEDULE NO.7A (In INR) Custom Duty/ Import Duty and Goods and Services Tax (GST), applicable on Schedule - 1 not included in bid price.

TOTAL OF SCHEDULE NO.7A (In Foreign Currency 1 i.e. USD) Custom Duty/ Import Duty and Goods and Services Tax (GST), applicable on Schedule - 1 not included in bid price.

TOTAL OF SCHEDULE NO.7A (In Foreign Currency 2 i.e. EUR) Custom Duty/ Import Duty and Goods and Services Tax (GST), applicable on Schedule - 1 not included in bid price.

TOTAL OF SCHEDULE NO.7A (In Foreign Currency 3 i.e. JPY) Custom Duty/ Import Duty and Goods and Services Tax (GST), applicable on Schedule - 1 not included in bid price.

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

SCHEDULE OF RATES AND PRICES:

Bidder's Name and Address :

SCHEDULE- 1 : Plant and Equipment including type test charges and mandatory spares to be supplied from Abroad. (BREAK-UP TO BE FURNISHED BEFORE AWARD)

Description

Currency 1

Main Equipments for Steam Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Steam Turbine Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Electrical System and C&I System of Main Plant

Factory Fabricated Steel Structures

Any other Main Equipments not covered in 1 to 4 above but required for the Scope of work under the package

TOTAL (A) MAIN EQUIPMENT [(1) + (2) + (3) +(4) +(5)]

GRAND TOTAL (A+B+C)

* Bidders shall enter a code representing the country of origin of all imported plant and equipment including mandatory spares.

.................................................................................................... (ATTACH SEPARATE SHEET, IF REQUIRED)

Not used

The summation of quantity of Factory fabricated structural works quoted by bidder, in Schedule-1 and/or Schedule-2 and the site fabricated steel structural works quoted by bidder in Schedule-4 shall be equal to total quantity of structural works envisaged by the bidder under the package. Installation Services price for factory fabricated steel structural items shall be separately indicated by the bidder in Schedule-4.

Bidder to note that only factory fabricated items and not the raw material shall be quoted in Schedule-1 and/or Schedule-2

Sequence of painting of structures as given in Technical Specification shall be followed.

Items listed above but priced in Schedule 2 shall be quoted as "0" by the Bidder in this Schedule 1.

Bidders are required to quote lumpsum price separately for various systems/equipments of main equipment and mandatory spares as sought in this schedule based on BOQ for main equipment & mandatory spares specified in Technical Specification.

Bidders are required to indicate the break up of Type Test Charges as per Schedule-8A.

Interchangebility and Packings: All spares supplied under this contract shall be strictly interchangeable with parts for which they are intended for replacements. These spares should include all mounted accessories like components, boards, add or items, fitting, connectors etc. and be complete in all respects so that the replacement of the main items by these spares does not require any additional item. The vendors must conform the pair to pair compatibility of each electrical spares modules with the modules supplied in the original package. All electronic modules should be pre set and/or preprogrammed for ready use at site. Alternatively, suitable instruction sheet indicating the details of required PCB jumper position, BCD switch setting, EPROM/PROM listing etc should be packed along with each module. Also a caution mark sign should be put on all such module which needs pre setting/pre programming before putting them in to service. The spare shall be treated and properly packed for long term storage

Identification: Each spare shall be clearly marked and labeled on the outside of the packing with its description. When more than one spare part is packed in single case, a general description of the contents shall be shown on the outside of such case and a detailed list enclosed. All cases, containers and other packages must be suitably marked and numbered for the purpose of identification.

In case the description / quantity for any item mentioned in Schedule is at variance from what has been stated in Technical Specification and its subsequent amendments and clarifications, the stipulations of Technical Specification and its subsequent amendment and clarification shall prevail.

DVC may place the award for any mandatory spares with NOA and/or within three years from the date of NOA as per mutually agreed despatch schedule and as per the price quoted by the bidder in their bid in accordance with the relevant clauses. However, the sum of the price quoted for all the mandatory spares shall be considered for evaluation purpose.

Bidder to refer ITB clause 11.1(d) while quoting its bid price.

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW) BIDDING DOCUMENT NO. :

SCHEDULE OF RATES AND PRICES:

Bidder's Name and Address :

SCHEDULE- 2 : Plant and Equipment including Type tests and Mandatory Spares to be supplied from within the Employer's Country. (BREAK-UP TO BE FURNISHED BEFORE AWARD)

Currency 1

Main Equipments for Steam Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Steam Turbine Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Electrical System and C&I System of Main Plant

Factory Fabricated Steel Structures

Any other Main Equipments not covered in 1 to 4 above but required for the Scope of work under the package

TOTAL (A) MAIN EQUIPMENT [(1) + (2) + (3) +(4) +(5)]

GRAND TOTAL (A+B+C)

Not used

The summation of quantity of Factory fabricated structural works quoted by bidder, in Schedule-1 and/or Schedule-2 and the site fabricated steel structural works quoted by bidder in Schedule-4 shall be equal to total quantity of structural works envisaged by the bidder under the package. Installation Services price for factory fabricated steel structural items shall be separately indicated by the bidder in Schedule-4.

Bidder to note that only factory fabricated items and not the raw material shall be quoted in Schedule-1 and/or Schedule-2

Sequence of painting of structures as given in Technical Specification shall be followed.

Items listed above but priced in Schedule 1 shall be quoted as "0" by the Bidder in this Schedule 2.

Bidders are required to quote lumpsum price separately for various systems/equipments of main equipment and mandatory spares as sought in this schedule based on BOQ for main equipment & mandatory spares specified in Technical Specification.

Bidders are required to indicate the break up of Type Test Charges as per Schedule-8B.

Interchangebility and Packings: All spares supplied under this contract shall be strictly interchangeable with parts for which they are intended for replacements. These spares should include all mounted accessories like components, boards, add or items, fitting, connectors etc. and be complete in all respects so that the replacement of the main items by these spares does not require any additional item. The vendors must conform the pair to pair compatibility of each electrical spares modules with the modules supplied in the original package. All electronic modules should be pre set and/or preprogrammed for ready use at site. Alternatively, suitable instruction sheet indicating the details of required PCB jumper position, BCD switch setting, EPROM/PROM listing etc should be packed along with each module. Also a caution mark sign should be put on all such module which needs pre setting/pre programming before putting them in to service. The spare shall be treated and properly packed for long term storage

Identification: Each spare shall be clearly marked and labeled on the outside of the packing with its description. When more than one spare part is packed in single case, a general description of the contents shall be shown on the outside of such case and a detailed list enclosed. All cases, containers and other packages must be suitably marked and numbered for the purpose of identification.

In case the description / quantity for any item mentioned in Schedule is at variance from what has been stated in Technical Specification and its subsequent amendments and clarifications, the stipulations of Technical Specification and its subsequent amendment and clarification shall prevail.

DVC may place the award for any mandatory spares with NOA and/or within three years from the date of NOA as per mutually agreed despatch schedule and as per the price quoted by the bidder in their bid in accordance with the relevant clauses. However, the sum of the price quoted for all the mandatory spares shall be considered for evaluation purpose.

Bidder to refer ITB clause 11.1(d) while quoting its bid price.

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW) BIDDING DOCUMENT NO. :

SCHEDULE OF RATES AND PRICES:

Bidder's Name and Address :

SCHEDULE- 3 : Local Transportation including Port Handling, Port Clearance & Port Charges, Inland Transit Insurance and other local costs incidental to delivery of plant & equipment and mandatory spares at site. (BREAK-UP TO BE FURNISHED BEFORE AWARD)

TOTAL (I + II)

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW) BIDDING DOCUMENT NO.

SCHEDULE OF RATES AND PRICES:

Bidder's Name and Address :

SCHEDULE- 4 : Installation Services [Erection, Civil, Steel Structural works (Site fabricated structures as permitted as per Specifications), Factory Fabricated Steel Structural Works (Erection) & Allied works] including insurance (other than transit insurance and other services as specified in the Bidding Documents). (BREAK-UP TO BE FURNISHED BEFORE AWARD)

Currency 1

Main Equipments for Steam Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Steam Turbine Generator System (Excl. Factory Fabricated Steel Structures, Electrical Systems and C&I System)

Main Equipments for Electrical System and C&I System of Main Plant

Erection of Factory Fabricated Steel Structures (corresponding to structures whose supplies is covered under Schedule-1 & 2)

Erection of Any other Main Equipments not covered in 1 to 4 above but required for the Scope of work under the package

TOTAL (A) MAIN EQUIPMENT [(1) + (2) + (3) +(4) +(5)]

TOTAL (A) + (B) + (C) + (D) + E+ (F)

Not used

The summation of quantity of Factory fabricated steel structural works quoted by bidder, in Schedule-1 and/or Schedule-2 and the site fabricated structural works quoted by bidder in Schedule-4 shall be equal to total quantity of structural works envisaged by the bidder under the package. Installation Services price for factory fabricated steel structural items shall be seperately indicated by the bidder in Schedule-4.

Bidder to note that only factory fabricated items and not the raw material shall be quoted in Schedule-1 and/or Schedule-2

Bidder to refer ITB clause 11.1(d) while quoting its bid price.

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW) BIDDING DOCUMENT NO. :

Bidder's Name and Address :

SCHEDULE OF RATES AND PRICES:

SCHEDULE- 5 : GRAND SUMMARY: NOT USED

GRAND TOTAL

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW) BIDDING DOCUMENT NO. :

Schedule-6

IFB NO. :

Bidder's Name and Address :

The prices indicated for items below shall be additional, if the Employer desires to purchase the same

Total Price (as delivered at Project)

TOTAL PRICE

Annexure…....

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

Note: 1. Domestically manufactured spares shall be quoted on Ex-works (India) basis and the spares to be supplied from abroad shall be quoted on CIF (Indian Port of Entry) basis.2. Continuation sheets of like size and format may be used as per Bidder's requirements and annexed to this Schedule. 2. Continuation sheets of like size and format may be used as per Bidder's requirements and annexed to this Schedule.

Schedule No. 7A : Custom Duty/ Import Duty and Goods and Services Tax (GST), applicable on Schedules - 1 not included in bid price: BREAK-UP TO BE FURNISHED BEFORE AWARD

The details of Custom Duty/ Import Duty and Goods and Services Tax (as on seven (07) days prior to the last date for submission of price bids) applicable on the price of goods and services quoted in Schedule-1, not included in the Bid Price and which may be payable by the Employer in accordance with the provisions of Bidding Documents are as under :

A. Custom Duty/ Import Duty

Currency 1

Total Custom Duty/ Import Duty payable (in Bid Currency)

CIF-Main Equipment (Schedule-1)

CIF-Mandatory Spares (Schedule-1)

Type Test charges (Schedule-1)

A. Custom Duty/ Import Duty

Currency 1

Total Custom Duty/ Import Duty payable (in Bid Currency)

CIF-Main Equipment (Schedule-1)

CIF-Mandatory Spares (Schedule-1)

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

3. Bidder to refer ITB clause 11.1(d) while quoting its bid price.

Schedule No. 7 : Goods and Services Tax (GST), applicable on Schedules - 2,3 & 4 not included in bid price: BREAK-UP TO BE FURNISHED BEFORE AWARD

The details of Goods and Services Tax (as on seven (07) days prior to the last date for submission of bids) applicable on the price of goods and services quoted in Schedule-2, 3 & 4, not included in the Bid Price and which may be payable by the Employer in accordance with the provisions of Bidding Documents are as under :

Currency 1

Ex-Works-Main Equipment (Schedule-2)

Ex-Works-Mandatory Spares (Schedule-2)

Type Test charges (Schedule-2)

F&I-Main Equipment (Schedule-3)

F&I-Mandatory Spares (Schedule-3)

Erection - Main Equipment (Schedule-4)

Civil Works (Schedule-4)

Training charges (Schedule-4)

AMC / AMS (Annual Maintenance Services) (Schedule-4)

Structural Works (Schedule-4)

Amount linked to Safety Aspects/ compliance to Safety Rules (Schedule-4)

Any other Price Component (not covered above)

TOTAL (GST)

Notes:

Bidder shall quote the GST as applicable in the Employer's country as on seven (7) days prior to the last date of submission of price bids.

Bidder to refer ITB clause 11.1(d) while quoting its bid price.

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

In case rate of GST is different for various items, such different rates of GST along with the amount on which such GST is applicable shall be suitably indicated by the bidders in this schedule.

Schedule No. 8A : Break up of Type Test Charges for Equipment Priced in Schedule-1: BREAK-UP TO BE FURNISHED BEFORE AWARD

Currency 1

LIST OF TYPE TESTS ON ELECTRICAL EQUIPMENTS

Generator and its Auxiliary Systems

Instantaneous Sudden Short Circuit

Determination of negative sequence and zero sequence reactance and resistance

Determination of voltage wave form and Total Hamonic Distortion Factor

Short circuit heat run test at two third of rated stator current at rated pressure and cooling parameters with one cooler/cooler section out of service and ten (10) percent of tubes plugged in remaining coolers/cooler sections that are in service. In case of unsymmetrical cooler configuration, test with all possible variants of one cooler out of circuit shall be carried out.

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Short circuit operation

Sudden short circuit conditions

Stand still condition with hammer test

(separate charges for each condition (a, b, c & d) shall be indicated)

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Short circuit operation

Sudden short circuit conditions

Input and output surge withstand capacity test

i) The fast transient SWC tests as per ANSI/IEEE C37.90.1-2002/IEC-60255-22-04-2008

Vibration measurement of stator end winding for the following conditions

Excitation transformer as per IEC-60076-11.

i. Short circuit Test

ii. Lighting Impulse Test

iii. Temperature rise Test (with and without fan/blower)

iv. Noise level Test

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Sudden short circuit conditions

Excitation Busduct as per IS:8084 / ANSI IEEE-37.23 / IEC 60439-2,60529& 62271

i. Temperature rise Test

ii. Dynamic and short time current Test

iii. Degree of protection Test

iv. Noise level Test

iv. one minute power frequency high voltage withstand Test

Test for estimating the discharging capability of the field discharge resistors in succession for atleast two discharges

Input and Output withstand capability test

(i) The fast transient SWC Tests as per ANSI/IEEE C 37.90.1-2002/IEC 60255-22-04-2008

HT MOTORS

No load saturation and loss curves upto approximately 115% of rated voltage

Measurement of noise at no load

Momentary overload test (subject to test bed constraint)

Full load test (Subject to test bed constraint)

Temperature rise test at rated condition

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Chopped wave Lightning Impulse voltage test

Measurement of harmonic current in no load current

PRD operation test

Short circuit test (To be conducted as described below) This short circuit test shall be performed on TR set along with the TR panel and controller with a spark gap connected across the output. The gap is adjusted to get the spark at required peak voltage which is the short circuit condition and the controller will control the voltage to quench the spark.

Vacuum test on tank

Pressure test on tank

Induced over voltage test

Measurement of no load losses and current

Measurement of impedance voltage/short circuit impedance and losses

Measurement of IR

Measurement of acoustic sound level

Degree of protection test on marshalling box

Measurement of capacitance and tan delta

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Chopped wave Lightning Impulse voltage test

Torsion test on shaft insulator

TR Set

Disconnecting Switch

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Temperature rise

Measurement of line current harmonics

Test capability to restart the system and resynchronize converter onto running motor after a voltage interruption

Generator busduct(Main,Delta and Tap Off run)/SPBD

Impulse voltage withstand on a typical section of busduct including one bend.

Heat run test on representative sections of 3-phase busduct, including one bend, CT's, bellows and flexible joints.

Short circuit tests on representative sections of 3-phase busduct, including one bend. The sections having longest span between support insulators shall be chosen.

Power frequency voltage withstand tests

Air leakage test and water tightness tests

circuit breaker / circuit breaker panels, of each voltage class and current rating

1) Short circuit duty test on circuit breaker, mounted inside the panel offered along with CTs, bushing and separators.

2) Short time withstand test on circuit breaker, mounted inside panel offered together with CTs, bushings and separators.

3) Power frequency withstand test on breaker mounted in side panel.

4) Lightning impulse withstand test on breaker mounted in side panel.

5) Temperature rise test on breaker and panel together. For this test, the test set up shall include three panels with breakers, the test breaker and panel being placed in the centre. The adjacent panels shall also be loaded to their rated current capacity. Alternatively, the test panel may be suitably insulated at the sides, which will be adjoining to other panels in actual site configuration

6) Internal Arc Test as per IEC 62271-200

7) Measurement of resistance of main circuit.

8) Mechanical operation test.

Contactor and Contactor panels of each type and rating.

1) Verification of rated making and breaking capacities of the contactor.

2) Short time withstand test of panel.

3) Power frequency test on the contactor mounted in side panel.

4) Lightning impulse voltage withstand test of the contactor mounted in side panel.

5) Measurement of resistance of main circuit.

Short circuit withstand test of earthing device (truck / switch).

GENERATOR TRANSFORMERS

Dielectric type test (IEC60076-3)

i) Switching impulse withstand voltage test.

ii) Lightning impulse withstand voltage test transformer winding Um ≤ 72.5 kV

iii) Separate-source withstand voltage test.

iv) Induced AC over voltage withstand test.

Temperature rise test. (IEC60076-2)

Pressure test and Vacuum test with deflection measurement.

Measurement of power taken by cooling fans & oil pumps.

Long duration induced AC voltage test (ACLD) transformer winding 72.5 < Um ≤ 170 kV

Short-circuit withstand test

Measurement of the harmonics of the no-load current and acoustic noise level as per NEMA TR-1

Determination of capacitances windings-to-earth and between windings

Short circuit withstand test of earthing device (truck / switch).

Over-fluxing test

UNIT TRANSFORMERS AND AUXILIARY POWER TRANSFORMERS

i) Lightning impulse withstand voltage test transformer winding Um ≤ 72.5 kV

iii) Separate-source withstand voltage test.

ii) Separate-source withstand voltage test.

iii) Induced AC over voltage withstand test.

STATION TRANSFORMER

To Performed on one transformer

i) Lightning impulse withstand voltage test, transformer winding Um ≤ 72.5 kV

ii) Temperature rise test.

Pressure test and Vacuum test with deflection measurement.

Measurement of power taken by cooling fans & oil pumps.

Long duration induced AC voltage test (ACLD) transformer winding 72.5 < Um ≤ 170 kV

Short-circuit withstand test

iii) Pressure test and Vacuum test with deflection measurement.

iv) Measurement of power taken by cooling fans & oil pumps.

NEUTRAL GROUNDING RESISTOR

Temperature rise test (on one unit of each voltage rating)

Short time current test along with Temperature rise test (on one unit of each voltage rating)

Degree of protection test for IPX3 on enclosure

Overall efficiency determination of VFD system including transformer/ Harmonic filters etc at motor full load

L.T. TRANSFORMERS

Impulse withstand test

Partial discharge measurement

Ingress Protection Test

BATTERY AND BATTERY CHARGER

On two cells of the Battery

a) Test for capacity - test for voltage during discharge

b) Ampere hour & watt-hour efficiency test

c) Endurance test

d) Container shall be type tested as per IS: 1146

e) Sealing compound shall be type tested as per IS: 3116

battery charger

a) Dielectric tests.

b) Voltage regulation check from 0 to 100% load with +_10% input voltage variation.

c) Ripple content measurement.

d) Functional tests.

e) Heat run test on current limiting value.

CABLES

As per relevent IS

ILLUMINATION SYSTEM

LM79 and LM80

cable trays and cable tray support system

a) Deflection tests and slip tests on cable trays and cable tray support system

b) Weld Integrity test

Main Turbine Oil Purification System

Measurement of line current harmonics

Measurement of capacitance and tan delta

Measurement of line current harmonics

Pressure drop test on one strainer for each type and size

MDBFP

Drive turbine oil Purification system

Vibration measurement of stator end winding for the following conditions

Measurement of line current harmonics

Open circuit operation

Measurement of line current harmonics

One number of each type & size as per Volume 2D1 (Power Cycle Piping, Valves and Specialties), Section 1, Clause 7.05.00.

Measurement of line current harmonics

Type test for Model testing of ACC Fan

Measurement of line current harmonics

NPSH (R) test on one CEP

Measurement of line current harmonics

Drip Pump Type Test (if envisaged)

NPSH (R) test on one drip pump

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Sudden short circuit conditions

PA Fan

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Test to establish unit functioning of pump at temp. & pressure

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Weighing accuracy, and repeatability test at various speeds with coal flow

Each identical type of metallic expansion joint (duct) to demonstrate compliance to EJMA requiremen

ts as per clause 6.03.09, Volume 2B, Section 1, Steam Generator and Accessories.

Bidder to note that in case for the balance C&I systems/equipment, the type test certificates furnished by the Bidder is (are) not acceptable to the Owner on the grounds indicated in the C&I section of technical specifications (Volume 2E) the relevant test(s) shall be conducted without any price repercussion to the Owner.

Qty. (Set/No.)

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

TOTAL (TO SCHEDULE-1)

Schedule No. 8A : Break up of Type Test Charges for Equipment Priced in Schedule-1: BREAK-UP TO BE FURNISHED BEFORE AWARD

Currency 1

LIST OF TYPE TESTS ON ELECTRICAL EQUIPMENTS

Generator and its Auxiliary Systems

Instantaneous Sudden Short Circuit

Determination of negative sequence and zero sequence reactance and resistance

Determination of voltage wave form and Total Hamonic Distortion Factor

Short circuit heat run test at two third of rated stator current at rated pressure and cooling parameters with one cooler/cooler section out of service and ten (10) percent of tubes plugged in remaining coolers/cooler sections that are in service. In case of unsymmetrical cooler configuration, test with all possible variants of one cooler out of circuit shall be carried out.

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Short circuit operation

Sudden short circuit conditions

Stand still condition with hammer test

(separate charges for each condition (a, b, c & d) shall be indicated)

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Short circuit operation

Sudden short circuit conditions

Input and output surge withstand capacity test

i) The fast transient SWC tests as per ANSI/IEEE C37.90.1-2002/IEC-60255-22-04-2008

Vibration measurement of stator end winding for the following conditions

Excitation transformer as per IEC-60076-11.

i. Short circuit Test

ii. Lighting Impulse Test

iii. Temperature rise Test (with and without fan/blower)

iv. Noise level Test

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Sudden short circuit conditions

Excitation Busduct as per IS:8084 / ANSI IEEE-37.23 / IEC 60439-2,60529& 62271

i. Temperature rise Test

ii. Dynamic and short time current Test

iii. Degree of protection Test

iv. Noise level Test

iv. one minute power frequency high voltage withstand Test

Test for estimating the discharging capability of the field discharge resistors in succession for atleast two discharges

Input and Output withstand capability test

(i) The fast transient SWC Tests as per ANSI/IEEE C 37.90.1-2002/IEC 60255-22-04-2008

HT MOTORS

No load saturation and loss curves upto approximately 115% of rated voltage

Measurement of noise at no load

Momentary overload test (subject to test bed constraint)

Full load test (Subject to test bed constraint)

Temperature rise test at rated condition

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Chopped wave Lightning Impulse voltage test

Measurement of harmonic current in no load current

PRD operation test

Short circuit test (To be conducted as described below) This short circuit test shall be performed on TR set along with the TR panel and controller with a spark gap connected across the output. The gap is adjusted to get the spark at required peak voltage which is the short circuit condition and the controller will control the voltage to quench the spark.

Vacuum test on tank

Pressure test on tank

Induced over voltage test

Measurement of no load losses and current

Measurement of impedance voltage/short circuit impedance and losses

Measurement of IR

Measurement of acoustic sound level

Degree of protection test on marshalling box

Measurement of capacitance and tan delta

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Chopped wave Lightning Impulse voltage test

Torsion test on shaft insulator

TR Set

Disconnecting Switch

TR Set

Temperature rise test at rated DC current at 1:1 charge ratio

Temperature rise

Measurement of line current harmonics

Test capability to restart the system and resynchronize converter onto running motor after a voltage interruption

Generator busduct(Main,Delta and Tap Off run)/SPBD

Impulse voltage withstand on a typical section of busduct including one bend.

Heat run test on representative sections of 3-phase busduct, including one bend, CT's, bellows and flexible joints.

Short circuit tests on representative sections of 3-phase busduct, including one bend. The sections having longest span between support insulators shall be chosen.

Power frequency voltage withstand tests

Air leakage test and water tightness tests

circuit breaker / circuit breaker panels, of each voltage class and current rating

1) Short circuit duty test on circuit breaker, mounted inside the panel offered along with CTs, bushing and separators.

2) Short time withstand test on circuit breaker, mounted inside panel offered together with CTs, bushings and separators.

3) Power frequency withstand test on breaker mounted in side panel.

4) Lightning impulse withstand test on breaker mounted in side panel.

5) Temperature rise test on breaker and panel together. For this test, the test set up shall include three panels with breakers, the test breaker and panel being placed in the centre. The adjacent panels shall also be loaded to their rated current capacity. Alternatively, the test panel may be suitably insulated at the sides, which will be adjoining to other panels in actual site configuration

6) Internal Arc Test as per IEC 62271-200

7) Measurement of resistance of main circuit.

8) Mechanical operation test.

Contactor and Contactor panels of each type and rating.

1) Verification of rated making and breaking capacities of the contactor.

2) Short time withstand test of panel.

3) Power frequency test on the contactor mounted in side panel.

4) Lightning impulse voltage withstand test of the contactor mounted in side panel.

5) Measurement of resistance of main circuit.

Short circuit withstand test of earthing device (truck / switch).

GENERATOR TRANSFORMERS

Dielectric type test (IEC60076-3)

i) Switching impulse withstand voltage test.

ii) Lightning impulse withstand voltage test transformer winding Um ≤ 72.5 kV

iii) Separate-source withstand voltage test.

iv) Induced AC over voltage withstand test.

Temperature rise test. (IEC60076-2)

Pressure test and Vacuum test with deflection measurement.

Measurement of power taken by cooling fans & oil pumps.

Long duration induced AC voltage test (ACLD) transformer winding 72.5 < Um ≤ 170 kV

Short-circuit withstand test

Measurement of the harmonics of the no-load current and acoustic noise level as per NEMA TR-1

Determination of capacitances windings-to-earth and between windings

Short circuit withstand test of earthing device (truck / switch).

Over-fluxing test

UNIT TRANSFORMERS AND AUXILIARY POWER TRANSFORMERS

i) Lightning impulse withstand voltage test transformer winding Um ≤ 72.5 kV

iii) Separate-source withstand voltage test.

ii) Separate-source withstand voltage test.

iii) Induced AC over voltage withstand test.

STATION TRANSFORMER

To Performed on one transformer

i) Lightning impulse withstand voltage test, transformer winding Um ≤ 72.5 kV

ii) Temperature rise test.

Pressure test and Vacuum test with deflection measurement.

Measurement of power taken by cooling fans & oil pumps.

Long duration induced AC voltage test (ACLD) transformer winding 72.5 < Um ≤ 170 kV

Short-circuit withstand test

iii) Pressure test and Vacuum test with deflection measurement.

iv) Measurement of power taken by cooling fans & oil pumps.

NEUTRAL GROUNDING RESISTOR

Temperature rise test (on one unit of each voltage rating)

Short time current test along with Temperature rise test (on one unit of each voltage rating)

Degree of protection test for IPX3 on enclosure

Overall efficiency determination of VFD system including transformer/ Harmonic filters etc at motor full load

L.T. TRANSFORMERS

Impulse withstand test

Partial discharge measurement

Ingress Protection Test

BATTERY AND BATTERY CHARGER

On two cells of the Battery

a) Test for capacity - test for voltage during discharge

b) Ampere hour & watt-hour efficiency test

c) Endurance test

d) Container shall be type tested as per IS: 1146

e) Sealing compound shall be type tested as per IS: 3116

battery charger

a) Dielectric tests.

b) Voltage regulation check from 0 to 100% load with +_10% input voltage variation.

c) Ripple content measurement.

d) Functional tests.

e) Heat run test on current limiting value.

CABLES

As per relevent IS

ILLUMINATION SYSTEM

LM79 and LM80

cable trays and cable tray support system

a) Deflection tests and slip tests on cable trays and cable tray support system

b) Weld Integrity test

Main Turbine Oil Purification System

Measurement of line current harmonics

Measurement of capacitance and tan delta

Measurement of line current harmonics

Pressure drop test on one strainer for each type and size

MDBFP

Drive turbine oil Purification system

Vibration measurement of stator end winding for the following conditions

Measurement of line current harmonics

Open circuit operation

Measurement of line current harmonics

Schedule No. 8B : Break up of Type Test Charges for Equipment Priced in Schedule-2: BREAK-UP TO BE FURNISHED BEFORE AWARD

Measurement of line current harmonics

Type test for Model testing of ACC Fan

Measurement of line current harmonics

NPSH (R) test on one CEP

Measurement of line current harmonics

Drip Pump Type Test (if envisaged)

NPSH (R) test on one drip pump

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Sudden short circuit conditions

PA Fan

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Test to establish unit functioning of pump at temp. & pressure

Vibration measurement of stator end winding for the following conditions

Open circuit operation

Type tests on field breaker as per IEEE/ANSI C-37-18/IEC 60947-2

Weighing accuracy, and repeatability test at various speeds with coal flow

One number of each type & size as per Volume 2D1 (Power Cycle Piping, Valves and Specialties), Section 1, Clause 7.05.00

One number of each type & size as per as per Volume 2C, Section 4 (Consenser and Air Extraction System), clause 7.05.00

Bidder to note that in case for the balance C&I systems/equipment, the type test certificates furnished by the Bidder is (are) not acceptable to the Owner on the grounds indicated in the C&I section of technical specifications (Volume 2E) the relevant test(s) shall be conducted without any price repercussion to the Owner.

Qty. (Set/No.)

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

Performance Test on actual fan of the size& type offered of following fans at shop (Refer clause 6.03.02 and 6.03.03, Volume 2B, Section 1, Steam Generator and Accessories)

TOTAL (TO SCHEDULE-2)

Schedule No. 8A : Break up of Type Test Charges for Equipment Priced in Schedule-1: BREAK-UP TO BE FURNISHED BEFORE AWARD

Cost implication on the Lumpsum bid price i.e. reduction/decrease (-) in the bid price

# Ex-works

Local Transportation & Insurance (Indian Rupees)

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

Installation

NOT USED

Employer shall finalise take out option up to 2 month of LOA.

# Ex-works

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

#CIF/Ex-Works Price

Local Transportation including Port clearance & Port charges and Inland insurance (Indian Rs.)

Employer shall finalise take out option up to 2 month of LOA.

The prices indicated below are additional prices/rebates in Bid Price for providing the alternatives to the base offer as specified in the Technical Specifications.

Ex-works/CIF

# Ex-works

MAIN POWER PLANT (MPP) PACKAGE FOR DURGAPUR THERMAL POWER PROJECT (1 X 800 MW)

Bidder's Name and Address :

Ex-works/CIF Price

Local Transportation and Insurance Charges

Schedule No. 8A : Break up of Type Test Charges for Equipment Priced in Schedule-1: BREAK-UP TO BE FURNISHED BEFORE AWARD

# Ex-works