PROVN OF BATHROOM BLOCKS NEAR BLDG NO T182 2 AT LIP AND OPEN TRAINING SHED AT TERRIERS ENCLAVE OF AGE BRI UNDER GE BRICHGUNJ

Amount

Rough excavation n exc 1.5m deep and getting out in any type of soil complete all as specified and directed by Engineer-in Charge.

M & L Excavating over areas, n exc 1.5 m deep and getting out Hard/Dense Soil complete all as specified and directed by Engineer-in Charge.

M & L Excavating over areas, exc 1.5 m deep and n exc 3.0 m and getting out Hard/Dense Soil complete all as specified and directed by Engineer-in Charge.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in any type of soil complete all as specified and directed by Engineer-in Charge.

M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling complete all as specified and directed by Engineer-in Charge.

M&L for Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces complete all as specified and directed by Engineer-in Charge.

M&L for use and removal of steel form work to faces of walls retaining walls, abutments, parapets and like for flat rough finished surfacecomplete all as specified and directed by Engineer-in Charge.

M&L for use and removal of steel form work to faces of walls retaining walls, abutments, parapets and like for flat fair finished surface complete all as specified and directed by Engineer-in Charge.

M & L for Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engineer-in Charge.

Use and waste of form work to sides and sofit of Beams for Fair finished surfaces complete all as specified and directed by Engineer-in Charge.

Use and waste of form work to sides and sofit of Slab & Chajja etc for Fair finished surfaces complete all as specified and directed by Engineer-in Charge.

M & L for RCC- M - 30 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in Charge.

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) above top of footings including attached pilasters and buttresses complete all as specified and directed by Engineer-in Charge.

M & L for RCC- M -30 Design Mix as in columns, pillars, piers,posts and struts complete all as specified and directed by Engineer-in Charge.

M & L for RCC- M -30 Design Mix as in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in Charge.

M & L for RCC- M -30 Design Mix as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in,shelves and the like complete all as specified and directed by Engineer-in Charge.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in Charge.

M&L Mild steel TMT bars 6 mm to 8mm dia cut to length bent to shape required and binding with mild steel wire annealed not less than 0.9 mm dia complete all as specified and directed by Engineer-in Charge.

All as per item no 18.00 here in before but 5mm dia and over up to and including 10mm dia as in stirrups, spacers, binders and the like complete all as specified and directed by Engineer-in Charge.

M&L for broken stone or boulders including hand packing (any thickness) at back side of weep holes and raising or lowering to the required level complete all as specified and directed by Engineer-in Charge.

M&L for 110 mm bore PVC pipes as in weep holes complete all as specified and directed by Engineer-in Charge.

M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed by Engineer-in Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in Charge.

Removing excavated soil to a distance exc 50 m but n.exc 250 m and depositing complete all as specified and directed by Engineer-in Charge.

M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B-O to horizontal or vertical surface including necessary formwork complete all as specified and directed by Engineer-in Charge.

M&L Rendering 10mm thick on concrete surfaces in CM (1:6) finished even & smooth without using extra cement complete all as specified and directed by Engineer-in Charge.

M&L Rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like finished even and smooth without using extra cement complete all as specified and directed by Engineer-in Charge.

M&L 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in Charge. (Note : Water proofing compound shall be measured and paid seperately)

Supply only integral WPC (3% by wt of cement)omplete all as specified and directed.

M & L For Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engineer-in Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of Oil Bound distemper over a coat of primer over a coat of internal wall care puttycomplete all as specified and directed by Engineer-in Charge.

All as per item no 31.00 here in before above but on Ceiling surfaces complete all as specified and directed.

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed by Engineer-in-Charge.(Make Apex Ultima)

M&L Filling under floors or in foundations including watering and consolidation complete all as specified and as directed by Engineer-in-Charge.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

M&L Hard Core of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in 75mm thick as in sub base complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in 40mm thick complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:3:6 type C1 using 20mm graded aggregate of 75 mm thick as in Plinth Protection complete all as specified and as directed by Engineer-in-Charge.

M & L Chequered cement concrete tiles, with grey cement and pigment 30cm x 30cm x 20mm thick set, jointed and pointed in neat cement slurrry in floors including 20mm thick screed bed in Cm 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L Coloured Non-Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor over 15mm thick screed bed in CM (1:6) complete all as specified and as directed by Engineer-in-Charge.

M&L Glazed Ceramic Coloured tiles 350x 250x 7mm/ 450X 350X 7mm thick as in Dado/Skirting/Steps etc set and jointed in neat cement slury and pointed in coloured cement to match all as specified and directed including backing coat 10mm thick in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for anodized aluminium sections (minimum anodisation 15 micros) for partitions, window and door with frame and shutters fully or partially glazed, side Hung type ( two numbers glazed and gauzed) without sash bars, with panel inserts of sheet glass, gauze including necessary jointing cleats, glazing clips, rubber beading, Neoprene packing, anodized aluminium snap beading, screws,i max hinges, butt hinges etc. The size of aluminium sections shall be all as specified in relevant IS code and SSR part-I and completed all as specified and as directed by Engineer-in-charge. (Note: (i) supply only panel inserts of glass/gauze, handles, tower bolts and sliding bolt will be measured and paid separately as supply only. (ii) Weight of aluminium section only shall be accounted for payments purpose. However, until rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts of glass/ particle board/gauze, handles, hinges, sliding bolts, tower bolts etc.)

Supply only 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed by Engineer -in-Charge.

Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each pane complete all as specified and as directed.

Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer-in-Charge.

S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21

S&F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified.

S&F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 250 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified.

S&F Aluminium anodised barrel tower bolt of extruded section of size 100mm long complete all as specified.

S&F 100 mm long extruded aluminium alloy anodised handles fabricated type complete all as specified.

S&F 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified.

S&F of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed to walls and ceilings or laid in floors complete all as specified.

S&F of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed to walls and ceilings or laid in floors complete all as specified.

S & F 1000 litres capacity Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted in position all as specified in SSR Part I

S&F 15mm Bore Stop Valves / Angle Cock Fancy Type Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends.

S&F 15mm concealed type brass chromium plated stop cock with long shank screwed down,high pressure,crown or capsten head,complete all as specified and directed

S&F in repairs Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed.

S&F CP shower rose of size 125mm with or without swivel joint including fixed to pipes complete all as specified and directed.

S&F looking mirror Bevelled Edge 600mmx450mm mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed

S&F Gun Metal Gate valves 20 mm dia with iron wheel head screwed both ends for iron pipes.

S&F Chromium Plated Steel Grating of 100mm size.

S&F Vitreous China Wash hand basin, white flat back size 550x400 mm including brackets(including Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & PVC waste pipe) all as specified & directed

S&F PVC flexible connections 15 mm dia 450 mm long with brass checknuts .

S&F 100 mm CI Floor trap with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor.

S&F 75mm dia outlet PVC (SWR) floor trap,plain with grating incl joining with solvent cement

S&F PVC (SWR) Gully 125/110 mm,seting and incl joining with solvent cement

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls and laid in floors

S&F 75mm dia PVC (SWR) bend with oval access door

S&F 110mm dia PVC (SWR) bend with oval access door

S&F PVC (SWR) cowls 75mm dia.

S&F PVC (SWR) cowls 110mm dia.

M&L for Concrete bed to drain pipes including packing under, and completely surrounding pipes with concrete after they are laid and tested in cement conrete 1:3:6 type C-2 around 110mm dia complete.

M&L for precast man holes cover slab with 1:2:4 type B1 using 20mm graded stone aggregate set in CM 1:4 incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement all as specified.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in surface channel / benching incl cost of use and waste of clean sawn wooden form work all as specified

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stoped ends etc

Excavation in post holes (or similar holes) each n.exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface.

Excavation in trenches not exceeding 1.5m wide and n exc 1.5m in depth for foundation etc n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified.

M&L PCC 1:3:6 type C2 (40 mm graded stone aggregate) in foundation concrete for post holes complete all as specified and directed

M&L for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6, type C1 (using 20mm graded stone aggregate), exc. 10cm in width, set in CM 1:4 all as specified and as directed.

S&F Steel works In tubular/ posts/ trusses/ purlin including special shaped washer etc.complete using ERW or induction butt welded tubes conforming to IS 1161-1797 grade St 240.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc and fixed by riveting or welding or with nut and bolts (including nuts and bolts) conforming to Fe-410-W grade E 251 Quality B complete all as specified and directed.

S&F Mild steel bolts exc 12mm dia and n exc 20mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long all as specified.

M&L Painting to new steel and iron surfaces of exc. 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and as directed.

M&L Preparation of surface and applying two coats of cement based paint over a coat of primer on wall surfaces all as specified.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based plain steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified.

S &F MS work in wind ties for roof including securing bolts all as specified

M & L for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit suitable size including Tee junction bends etc in wall/fixed on ceiling and PVC switch board box type complete all as specified and as directed by Engineer-in-Charge.(a) One light point controlled by one way switch

(b) One ceiling fan point controlled by one way switch

(c) One three pin 5 Amp switch socket cum on same board

Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed.

Supply and fix energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of following size. (a) 50 mm bore.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

Supply and fix energy efficient LED Smart bright batten 10 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

S&F Street light New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 35 w as light and electronic driver complete all as per with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix in repair metal enclosure distribution board SPN, 4 way 240 volts, with 100 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line including fittings required for connection complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Supplying, hoisting and fixing rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of 1000 Litre capacity etc complete all as specified and directed.

DEEPAK AGENCIES

KML CONSTRUCTION

Bismi Builders & Enterprises

bansal construction

Kakolil Trade Agencies

Hindustan Traders

SUBASH FURNITURE SHOP