REPAIR AND POLISHING OF DIFFERENT WOODEN FURNITURE ITEMS OF GOVT MD AND OTM ACCN AND AT HQ 34 WEU UNDER GE MINNIE BAY, SRI VIJAYA PURAM

BED HARD/BED PLY TOP (1980mmx900mmx660mm)

S&F 12mm thick plywood BWP Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 1st quality Paduak wood long rail 1980mmx35mm x 90mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge

All as per item No. 1.02, but short rail all 900mmx35mm x 90mm as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to head board consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 400mm horizontal including legs of size 60 x 60mm in section at top and length 400mm from bottom of leg and 30 x 30mm in section at bottom complete including removal of damaged head board all as specified on drawing or as directed by Engineer-in-charge.

All as per item No. 1.04, but foot board consisting of 22 x 75mm in section paduak battens 3 Nos at equal space, joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30 x 60mm shall be 1st quality of Padauk wood. The vertical legs above horizontal rails shall be 30 x 60mm all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to new 1st quality Paduak wood stiffeners of size 40 x 60mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 4mm thick one side teak finished plywood of size 780 x 340mm including 12mm dia half cut teak wood beading of both side of head board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 4mm thick one side teak finished plywood of size 780 x 180mm including 12mm dia half cut teak wood beading of both side of foot board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to flat iron of mild steel of size 35mm x 5mm, bents to right angle on each corners of Bed Hard all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

CHARPOY WOODEN W/PLY TOP

S&F 12mm thick plywood BWP Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 1st quality Paduak wood long rail 1980mmx35mm x 90mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge

All as per item No. 1.02, but short rail all 900mmx35mm x 90mm as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to new 1st quality Paduak wood stiffeners of size 40 x 60mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

CHAIR DINING (440MMx430MMx890MM)

Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. .

Removing the existing unserviceable back rest and proving new Padauk wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65mm drilling holes at 12.5 mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and proving new Padauk wood rear rail including drilling holes at 12.5 mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65 mm including drilling holes at 12.5mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair dining with best quality of approved plastic cane 1.80 x0.46mm cane and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping, treating with anti termite chemical and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

CHAIR WOODEN BOTTOM

Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and proving new Padauk wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and providing new Padauk wood rear rail complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable plywood seat and replace with 12 mm thick BWP seat of suotable size rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping, treating with anti termite chemical and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

CHAIR WRITING (530MMx470MMx890MM)

Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 55x30x890mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 55x30x660mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new Padauk wood back rest of size 50 x 15mm slightly curved made out of 50x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65mm including drilling holes at @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail and providing new Padauk wood rear rail of size 30x65mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

(Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65mm including drilling holes @ 12.5mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest of size 60x25 mm and providing new Padauk wood arm rest complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair writing with best quality of approved plastic cane 1.80 x0.46mm cane and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

CHAIR EASY

Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 55x25 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 50x25mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new Padauk wood arm rest of size 65x25x610mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front frame and providing new Padauk wood front frame of size 55x25 mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 50x25 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable rear rails and providing new Padauk wood rear rails of size 50x25mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 1.80 x 0.46 mm cane and border with 3x0.60 mm cane complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

COMMON FOR ALL CHAIRS

Removing the existing unserviceable stiffeners and providing new Padauk wood 2nd class hard wood stiffeners of thickness 25x20 mm .

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

PEG TABLE

M & L for removing the existing unserviceable leg and providing with new Padauk wood rear leg complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable top rail and providing with new Padauk wood top rail complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable bottom stiffiner and providing with new Padauk wood bottom stiffiner complete all as specified on drawing or as directed by Engineer-in-charge.

(a) Replacement of existing unserviceable top for Peg Table made out of pre laminated MDF board 18mm thick with one side teak facing and balancing white on the other and fixed with suitable wooden beading (Padauk) on all the four sides all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

STOOL DRESSING CB

Removing of existing unserviceable legs of stool dressing and providing with new legs of 1st quality Paduak wood of size 50 x 30 x 380mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table Centre made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable front and rear rails of stool dressing and providing with new front and back of1st quality Paduak wood of size 25 x 65 mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable plastice cane of Stool dressing and recanning the same with half round 2mm wide and 0.4mm thick plastic cane, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

STOOL DRESSING WITH CUSHION

Removing of existing unserviceable legs of stool dressing and providing with new legs of 1st quality Paduak wood of size 50 x 30 x 380mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table Centre made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable front and rear rails of stool dressing and providing with new front and back of1st quality Paduak wood of size 25 x 65 mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING GENTS

Removing of existing unserviceable side rails of stool dressing and providing with new side rails of1st quality Paduak wood of size 25 x 50 mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

S & F in repairs new mirror 5mm thick of approved make with full frame all as specified on drawing or as directed by Engineer-in-charge.

S & F in repairs new top made out of 18 mm thick pre laminated MDF borad of approved make, all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING LADIES

S & F in repairs table top of Table dressing ladies with 18 mm thick pre-laminated MDF Board of approved make, all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs new Glass shuttrs of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.(Each glass shutter shall be measured as single unit)

Removing the existing unserviceable Aluminium channel and S & Fixed in repairs Aluminium Channel all as specified on drawing or as directed by Engineer-in-charge.

S & F in repairs new back suport made out of 6 mm thick plywood for mirror of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.

S & F in repairs new mirror 5 mm thick for Table dressing ladies of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

Table Bed Side

Removing of existing unserviceable side of Table Bed Side and providing new sides of 18mm thick prelaminated MDF Board with teak veneer facing one side and balancing white on the other side of exterior grade and 18 x 6 mm teak wood beading on front sides, rest all as specified on drawing or as directed by Engineer-in-charge. (Each sides will be measure as single unit)

Removing of existing unserviceable Top of Table Bed Side and providing new Top of 18mm thick prelaminated MDF Board with OST and balancing white on the other side of exterior grade and 18 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable Back of Table Bed Side and providing new Back of 6mm plywood BWP Grade shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable shelf of Table Bed Side and providing new shelf of 12mm thick prelaminated MDF Board with teak veneer facing one side and balancing white on the other side of exterior grade and suitable teak wood beading on front sid

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

SIDE BOARD (1200mm x 455mm x 760mm)

es, rest all as shown on drg and as directed by Engr-in-Charge.

Removing the existing unserviceable top of side board and providing new top made out of 18mm thick prelaminated MDF board exterior grade of size 1220 x 455 mm all as specified on drawing or as directed by Engineer-in-charge.

Removing he existing unserviceable back of Side Board and providing new Back with 6mm thick plywood BWP type of Size 650 x 1220 mm all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Top drawer and providing New drawer made out of 18 mm thick prelaminated MDF board on both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 18 mm thick prelaminated MDF board on both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing or as directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit)

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated MDF board of size 400x600 mm including Hinges rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit)

Removing the existing unserviceable leg frame of side board and providing Padauk wood 2nd class hard wood leg frame all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken legs of side board and providing new Padauk wood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each leg will be measured as single unit.)

Replacement of existing damaged hinges with 75mm long piano type hinges of shutters.

Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying french polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

BOOK CASE (WOODEN)

Removing the existing unserviceable Top of Book Case (wooden) and providing new top made out of 18mm thick prelaminated MDF board exterior grade one side Teak Face and other side balancing white, rest all as specified on drawing or as directed by Engineer-in-charge.

Removing he existing unserviceable back of Boook Case wooden and providing new Back with 6mm thick plywood BWP type, rest all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated MDF board including Hinges rest all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit)

Removing the existing unserviceable leg frame of side board and providing Padauk wood 2nd class hard wood leg frame all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

TEAPOY WOODEN

Replacement of existing unserviceable top for Teapoy made out of pre laminated MDF board 18mm thick with one side teak facing and balancing white on the other and fixed with suitable wooden beading (Padauk) on all the four sides all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from teapoy made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from teapoy made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE DINING 8/6/4 PERSONS

S&F in repairs to unserviceable damaged legs from Table dining 8/6/4 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table dining 8/6/4 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged long rails from Table dining 8 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable table top for Table dining 8 persons made out of prelaminated MDF board 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (Padauk) on all the four sides all as specified on drawing or as directed by Engineer-in-charge.

Replacement of existing unserviceable table top for Table dining 6 persons made out of prelaminated MDFboard 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (Padauk) on all the four sides all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged long rails from Table dining 6 persons made out of hard wood (Padauk) , rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable table top for Table dining 4 persons made out of prelaminated MDF board 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (Padauk) on all the four sides or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

(h) S&F in repairs to unserviceable damaged long rails from Table dining 4 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S & Fixed in repairs new mirror 5 mm thick for Hat stand with mirror of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Removing of existing unserviceable Back of Hat stand with mirror and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge.

Hat Stand with mirror

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F of brass pegs with brass screw in place of broken/ lost pegs in hat stand with mirror, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WITH DRAWER 900x 600 x 760mm

Removing of existing unserviceable table top for Table with drawer 900 x 600 x 760mm and providing new table top made out of 18mm thick prelaminated MDF board with teak facing one side and balancing white on the other side of exterior grade and 18 x 4 mm teak wood beading on all round, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged drawers from Table with drawer 900x600x760mm made out of hard wood (Padauk) including providing 6mm thk commercial ply to bottom of drawer complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table with drawer 900x600x760mm made out of hard wood (Padauk) size 60x30x740mm rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table with drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (short side) from Table with drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (long side) from Table with drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

S&F in repairs to unserviceable damaged side short rails from Table without drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on

drg and as directed by Engr-in-Charge.

TABLE WITHOUT DRAWER 900x 600 x 760mm

Removing of existing unserviceable table top for Table w/o drawer 900 x 600 x 760mm and providing new table top made out of 18mm thick prelaminated MDF board with teak facing one side and balancing white on the other side of exterior grade and 18x4 mm teak wood beading on all round, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) size 60x30x740mm including applying two coats of French polish including preparation of surfaces complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

S&F in repairs to unserviceable damaged bottom stiffners (short side) from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (long side) from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE 900x 900 x 760mm

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

Removing of existing unserviceable table top for Table 900 x 900 x 760mm and providing new table top made out of 18mm thick prelaminated MDF board with teak veneer facing one side and balancing white on the other side of exterior grade and 18x4 mm teak wood beading on all round, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (long side) from Table w/o drawer 900x600x760mm made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE 900x 900 x 760mm

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table 900x900x760mm made out of hard wood (Padauk) size 60x30x740mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WOODEN 1520X860X760

TABLE WRITING

Removing of existing unserviceable table top for Table writing and providing new table top made out of 18mm thick prelaminated MDF board with walnut color facing one side and balancing white on the other side of exterior grade and 18 x 4 mm teak wood beading on all round, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs made out of hard wood (Padauk) all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

&F in repairs to unserviceable damaged front long rails made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (short side) made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one

S&F in repairs to unserviceable damaged cabinet door made out of 18 mm thick prelaminated MDF board with teak face one side and balancing white on the other side of exterior grade and 18x4 mm teak wood beading on all round,, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged drawers made out of hard wood (Padauk) including providing 6mm thk commercial ply to bottom of drawer complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE CENTRE

Replacement of existing unserviceable top for Table Centre made out of pre laminated MDF board 18mm thick with one sidewalnut color facing and balancing white on the other exterior grade and fixed with 18x12mm wooden beading (Padauk) on all the four sides all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge.

S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one