Construction of State Ground Water

Amount

CIVIL WORK Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. (as per DSR 2.31)

EXCAVATION in foundation in ordinary soil (loam clay or sand ) including lift upto 1.5m lead upto 30.0m & including filling watering and ramming of excavated earth into the space between the building & sides of foundation trenches or into the plinth and removal & disposal surplus earth as directed by the engineer I/C within a lead of 30 m. from foundation trenches. (as per SOR 251)

Add to items 251-253 for every additional 30m (100fts) lead or part of 30m (100fts) or for every additional 1.5m lifts or part of 1.5m (as per SOR 254)

Add to items 251-253 for every additional 30m (100fts) lead or part of 30m (100fts) or for every additional 1.5m lifts or part of 1.5m (as per SOR 254)

Filling by CARTED earth in trenches , plinth, sides of foundation etc . inlayers not exceeding 20 by ramming and watering including lead upto 50m &lift upto 1.50m

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (as per SOR 255)

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8.00Kms. from the site of work including watering , ramming , dressing etc. labour & T&P etc required for proper completion of work sapling of girth upto 30 ground level and removal of rubbish upto a distance of 50m out side the periphery of area cleared . under floor fine sand. (as per SOR 255+Sand Rate)

Providing and laying Cement concrete 8:4:1 of not less than strength of M150 [stone ballast 8 (40mm normal size) 4 approved coarse sand :1cement] and curing complete, also including cost of formwork in foundation and floors. (as per SOR 281)

Providing and laying in position cement concrete of specied grade excluding the cost of centering and shuttering (for filling of drain haunches) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) (as per DSR 4.1.3)

Reinforced cement concrete work in RCC culvert slab with 1:1.5:3 (1 cement : 1.5 coarse sand and 3 gradded stone aggregate of 20 mm nominal size) excluding centering and shuttering and reinforcement. (as per DSR 5.3, 5.2.2, 5.2.3)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum.Excess/less cement used as per design mix is payable/recoverable separately). All works upto plinth level (as per DSR 5.37)

All works above plinth level upto floor V level (as per DSR 5.37.1)

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete (as per DSR 5.9)

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. (as per DSR 5.9.1)

Suspended floors, roofs, landings, balconies and access platform (as per DSR 5.9.2)

Shelves (Cast in situ) (as per DSR 5.9.3)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (as per DSR 5.9.4)

Columns, Pillars, Piers, Abutments, Posts and Struts ( as per DSR 5.9.5)

Stairs, (excluding landings) except spiral-staircases (as per DSR 5.9.6)

Weather shade, Chajjas, corbels etc., including edges (as per DSR 5.9.19)

Providing and fixing sheet covering over expansion joints with iron screws as per design. (as per DSR 5.29.2.1)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) (as per DSR 5.11)

Add for using extra cement in the items of design mix over and above the specified cement content therein. (as per DSR 5.35)

Class-150 brick work in 1:6 cement and COARSE sand in foundation and plinth including supply of all materials,labour tools and palnts ,etc . Required for proper completetion of the work. (as per SOR 303, 307, 306)

Class-150 brick work in 1:6 cement and COARSE sand mortar in SUPERSTRUCTURE including supply of all materials, labour tools and plants,etc.Required for proper completion of the work. (as per SOR 303, 307, 306, 309, 310) PARKING AREA

TERRACE

Class-150 HALF brick work in 1:4 cement and COARSE sand mortar in SUPERSTRUCTURE including supply of all materials, labour tools and plants,etc.Required for proper completion of the work. (as per SOR 305B, 309, 310A) G.F.

TERRACE

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pitswall trenches basement excavation top surface if plinth filling junction of wall and floor along the external perimer of binding expansion joints,surroundings of pipes and conduit etc. complete(Plinth area of the building at ground floor only shall be measuredas per I.S. 6313 (Part II 1981) Aldrine emulsifiable concentrate or any other approved material such as Hepthachlor or chlordance will be used. The rateof applications of chemical emulsion shall be as Follows :- (1) Treatment for Masonary & foundatiion 5 Liters per Sq.m.(2) Back fill in immediate contract with foundation 7.5 Litres per Sq.M.(3) Treatment of Top surface of plinth filling 5 Litres per Sq.M.(4) Treatment of soil along External Perimerter of Building 7.50 Litres per Sq.M.(5) Treatment of soil under Apron Along extrnal Perimeter 5 litres per sq.M

HYSD or iron in plain work such as reinforced concrete or reinforced brick work (when not inclluded in over all rates) wrought to required shape as necessary including bending, and also including supply of steel and wastage and overlapping and hookes required for completion of the work.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) Sal wood (as per DSR 9.1)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and with decorative both side high pressure laminated sheet of plain /wood grain in gloss/mat /suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S, including cost of adhesive of approved quality of 1.0mm thick including 32X5mm salwood lipping on edges of shutters. (as per DSR 9.20.1, 9.127.2) 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. (as per DSR 9.121)

30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. (as per DSR 9.122.1)

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge. (as per DSR 26.30.1)

Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener (as per DSR 14.3)

Providing and Fixing of S.S tower Bolt with necessary screws etc complete :250x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete -250X10 MM (as per DSR 9.63.1)

Providing and Fixing of S.S tower Bolt 150 mm with necessary screws etc complete :150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (as per DSR 9.63.3)

Mortise Handle set 8" +Mortise lock – bedroom Mortise Lever Lock shall be of Chromium plated and shall have 6 levers and a pair of handles of pressure die cast zinc alloy along with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. (as per DSR 9.76)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (as per DSR 9.66.1)

Providing and Fixing of S.S handle D type 150 mm mm dia with necessary screws etc complete: 150 mm

Providing and Fixing of SS door stopper with necessary screw etc complete

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. (as per DSR 9.83)

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). (as per DSR 9.136)

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately). (as per DSR 9.137)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately (as per DSR 9.147D) Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) (as per DSR 9.147D-2)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm) (as per DSR 9.147D-2)

Providing and fixing factory made uPVC white colour Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) (as per DSR 9.147 B-1)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (as per DSR 10.28)

Mild Steel or iron of small size and sections such as holding down bolts, hold fast , tie rods, grating etc,( when not including in as overall rates ) wrought to required shape as necessary for bending etc including supply of steelo and its wastage including cost of bolts, nuts if requird, welding, grinding and making holes as required for completion of work but Fabrication of Grill

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : (as per DSR 22.7) 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (as per DSR 22.7.1)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. (For the purpose of measurement the entire treated surface will be measured.) (as per DSR 22.6)

BRICK BATS (as per DSR 362)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (as per DSR 12.21.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (as per DSR 12.22)

Providing/laying of light cinder filling /25mm O.B.brick ballast under floor of toilet /sunkan roofs (as per SOR 255+CH-1/2b)

12 mm thick cement plaster in 1:6 cement - coarse sand mortar. (as per SOR 586, 583, 582)

15 mm cement plaster on rough side of single or half brick wall of mix:1:6 cement-coarse sand mortar. (as per SOR 586, 583, 582,)

15mm cement plaster in single coat on plinth 1 cement : 4 course sand in plinth (as per SOR 584, 583, 582)

2.5 CM (1") 1:2:4 Plain cement concrete floor with cement , approved coarse sand 2cm (3/4") graded approved stone laid in panels finished with 3mm ,(1/8") flooring coat of neat cement or cement and marble dust in 5:1 as specified over & including 8cm (3") thick base concrete consisting of cement . localk sand and brick ballast 4cm (1.5") gauge in the proportion of 1:4:8 and removing any over lapping mortar at the joints of panels if any and giving them a uniform finish including supply of all materials , labour and T&P etc. required for proper completion of the work. (as per SOR 600)

Finishing walls with water proof cement paint of approved quality on new work wuth two coats to give an even shade , including supply of all material labour and T&P etc required for proper completion of the work. (as per SOR 660)

12 mm cement plaster in single coat on fair side of single or half brick wall for interior plastering upto two floor including brick wall for interior plastering upto floor two level including internal rounded angles chamfers and/or rounded angles not exceding 80mm in grith and finished evenand smooth no.extra for mixing and additive (I) 1 cement:3 course sand in celling (as per SOR 583, 587)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete . Size of Tile 600x600 mm (as per DSR 11.41.2)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm (as per DSR 11.46.2)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (as per DSR 11.39)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete (as per DSR 8.31)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (as per DSR 11.56.1)

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (as per DSR 11.55.1)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick (as per DSR 11.26.1)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (as per DSR 11.27)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm (as per DSR 8.2.2.2)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work (as per DSR 8.3.2)

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (as per DSR 8.5)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar (as per DSR 19.15.1)

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg (as per DSR 19.18.2)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia (as per DSR 23.3)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, onforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia (as per DSR 23.4)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (as per DSR 23.5)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer- incharge. (as per DSR 23.6)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (as per DSR 23.7)

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge. (as per DSR 23.8)

Supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. having thermobonding a draining core - HDPE geonet comprises of two sets of parallel overlayed ribs integrally connected to have a rhomboidal shape with a polyethylene film and a nonwoven geotextile having mass per unit area 130 gsm and tensile strength of 8.0 kN/m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 0.7 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength of 13.5 kN/m , with mass per unit area of 830 gsm, at easily accessible location including top and bottom, with all leads and lifts, manpower and machinery, materials, labour etc. complete and as directed by Engineer - In - Charge (as per DSR 26.17)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in pproved laboratory, i/c disinfection of ubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per uirement and direction of Engineer-in-charge. (as per DSR 23.12)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia (as per DSR 23.13.3)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia (as per DSR 23.15.3)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). (as per DSR 16.75)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (as per DSR 13.80)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (as per DSR 13.47)

Mild steel or iron work in heavy sizes such as trusses, builts up gates, door frames, records racks roof work ,gate etc. wrough to required from, including drilling holes, rivetting or welding where necessary, and also including supply of steel, bolts, nuts and wastages etc. and their fixing required for completion of the work.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) (as per DSR 16.53)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work (as per DSR 13.60.1)

One priming coat and one coat of dry distemper on new work including supply of all materials labour and T&P etc required for proper completion of work. As in item 681 above but for each coat of distemper after the first coat (as per SOR 681, 682)

Painting two coats over priming coat on wood & other wooden surface upto 10cm width or grith or small articles not exceeding 0.10 sqmt. in areas with superior synthetic enamel such as Luxol 3Hi gloss aqcolite superlac. Dulux specified finishing. (as per SOR 641, 642)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

C/O Apron drain of width 150mm and depth as per required of sitr but minimum 250 mm with neat finish & required slop as per approved by E/I

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. (as per DSR 11.13.1)

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Foundations, footings, bases of columns, etc. for mass concrete

Providing and laying design mix cement concrete of M-30 grade,200mm thickness in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately Cement concrete prepared with batch mixing machine

INTERLOCKING TILES- Rubbr moulded reflective Zig-Zag 80mm Providing and Laying of interlocking Concrete Block Pavement having thickness 60mm as per drawing and Technical Specifivation Clause-1504 (as per SOR 1500 more spec)

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge. (as per DSR 11.45) GLASS PARTITION WALL WITH DOOR SHUTTERS AND FIXTURES

12MM TOUGHENED GLASS

INSTALLATION CHARGES

HOLES CHARGES

CUTOUT CHARGES

SILICON CHARGES

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. (as per DSR 2.28)

Supply & stacking of good earth at site including royalty and carriage up to 1 km ( earth measured in stacks will be reduced by 8% for payment) (as per DSR 2.3)

Supply & stacking of manure at site from approved source , including carriage up to one km (manure measured in stacks will be reduced by 8% for payment .) Screened through sieve of I.S designation 4.75 mm 34% of item 1 (as per DSR 2.4)

Spreading of sludge, dump manure or/ and good earth in required thickness .( Cost of sludge , dump manure or/and earth to be paid separately) As per Item No.- 2 (as per DSR 2.8)

Mixing earth and sludge or manure in proportion specified or directed item no 1+ item no 3 (as per DSR 2.9)

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) (as per DSR 2.57) Trees Plant

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v (as per DSR 7.24)

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge. (as per DSR 7.5)

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge. (as per DSR 7.53)

Providing and Displaying Sunflower hybrid well developed 15 to 20 cm ht. with fresh & healthy foliage at blooming stage in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge (as per DSR 4.8)

Providing and Displaying Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. (as per DSR 4.36)

Providing and Displaying Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. (as per DSR 4.24)

Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. (as per DSR 4.93)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) (as per DSR 2.14.1)

Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: (as per DSR 2.15)

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge. (as per DSR 2.16)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (as per DSR 17.1) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (as per DSR 17.1)

Providing and fixing white vitreous china water closet squatting pan (Indian type) : (as per DSR 17.13) Orissa pattern W.C. pan of size 580x440 mm (as per DSR 17.13)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : (as per DSR 17.2) W.C. pan with ISI marked white solid plastic seat and lid (as per DSR 17.2) Providing and fixing wash basin with C.I. brackets, 15 mm C.P. Brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (as per DSR 17.2)

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps (as per DSR 17.7.3)

White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap (as per DSR 17.7.7)

Providing and fixing CP Brass 32mm size Bottle Trap of bapproved quality & make and as per the direction of Engineerin- charge. (as per DSR 17.22A)

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : (as per DSR 17.5) Single half stall urinal with 5 litre P.V.C. automatic flushing cistern (as per DSR 17.5)

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. (as per DSR 17.8)

Providing & fixing C.P. Brass health faucet for ablution with 1 meter long PVC tube, hand shower, couplings, wall hook and other accessories.

Providing & Fixing fully automatic No Touch hand dryer of ABS body, suitable to operate on 220 V / 50 Hz AC power, 1650 Watt, having < 30 sec drying time, 1 min. auto cut complete with brackets.

Providing & fixing C.P. Brass Double coat Hooks with CP screws.

Providing & Fixing 600 X 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (as per DSR 17.31)

Providing & fixing toilet paper holder. (as per DSR 17.34) viterous china (as per DSR 17.34)

Providing C.P Brass towel ring (Jaquar,Essco,cera,Hindware) (as per SOR Chapter-22 Item-25)

Fixing C.P Brass towel ring (Jaquar,Essco,cera,Hindware)

Providing C.P Brass Soap Dish (Jaquar,Essco,cera,Hindware) (as per SOR Chapter-22 Item-24)

Fixing C.P Brass Soap Dish (Jaquar,Essco,cera,Hindware)

Providing and fixing S.Steel paper dispenser capacity (auto cut paper towels) with accesaries and complete in all respect.

Wall Mountable Water Purifier With Transparent Cover. Mineral ROTM Technology - Double Purification by RO+UF with TDS Controller - KENT PRIDE

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 110 mm dia (Wall Thickness - 3.2 to 3.8 mm)

75 mm dia (Wall Thickness - 3.2 to 3.8 mm)

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete as required. 32 mm dia.

40 mm dia.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in all respects. Multi Floor Trap (5" Ht) with height raiser and branch saddle strip of 50/75 mm outlet

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser

P-Trap type Floor Trap 110 x 75 mm

Providing C.P brass waste jali for sink/washbasin (as per SOR Chapter-21 Item-94)

Fixing C.P brass waste jali for sink/washbasin

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with screws and other required fitting complete as required.

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for rain water disposal, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, couplers, expansion joints / bellows, cowels, clamps, rubber rings, MS gratings over pipes of bell mouth construction with epoxy painting etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. The Pipes will be supported with threaded G I rods & clamps on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 110 mm dia

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (as per DSR 12.22)

Providing & fixing 15 mm nominal bore 45 cm long unplasticised PVC connection pipe with brass unions. (as per DSR 18.21) 45 cm length 15 mm nominal bore

Providing and fixing C.P brass bib cock of approved quality conforming to IS standards IS: 8931. 15 mm nominal bore (as per DSR 18.49)

Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (as per DSR 18.5) 15 mm nominal bore (as per DSR 18.5)

Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931. (as per DSR 18.53.1) 15 mm nominal bore (as per DSR 18.53)

Constructing brick masonry chamber 300 x 300 x 500 mm, inside with F.P.S. brick work in cement mortar 1: 4 (1 cement : 4 coarse sand) for Stop Cock, with C. I. surface box 100 x 100 x 75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix (1cement : 2 coarse sand:4 grade stone aggregate 20mm nominal size); necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (as per DSR 18.32)

Providing & Fixing G.I. Unoun in G.I. pipe including cutting and threading the pipe & making long screws etc. complete. 15mm dia nominal bore (as per DSR 18.46)

20mm dia nominal bore (as per DSR 18.46.1)

25mm dia nominal bore (as per DSR 18.46.2)

32mm dia nominal bore (as per DSR 18.46.3)

40mm dia nominal bore (as per DSR 18.46.4)

50mm dia nominal bore (as per DSR 18.46.5)

65mm dia nominal bore (as per DSR 18.46.6)

Cutting holes up to 30 X 30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks (as per DSR 18.76)

Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes CTS-SDR 11, class-1 CPVC Pipes (pressure rating 28 kg/cm2 at 23oC and 7 kg/cm2 at 82oC) confirming to IS : 15778-2007, ASTM D-2846, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. (as per DSR 18.7) 15mm nominal outer dia pipes (as per DSR 18.7)

20mm nominal outer dia pipes (as per DSR 18.7.1)

25mm nominal outer dia pipes (as per DSR 18.7.2)

32mm nominal outer dia pipes (as per DSR 18.7.3)

40mm nominal outer dia pipes (as per DSR 18.7.4)

50mm nominal outer dia pipes (as per DSR 18.7.5)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (as per DSR 18.9) 62.50 mm nominal inner dia Pipes (as per DSR 18.9)

75 mm nominal inner dia Pipes (as per DSR 18.9.8)

100 mm nominal inner dia Pipes (as per DSR 18.9.9)

Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes CTS-SDR 11, class-1 CPVC Pipes (pressure rating 28 kg/cm2 at 23oC and 7 kg/cm2 at 82oC) confirming to IS : 15778-2007, ASTM D-2846, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. (as per DSR 18.8) 15mm nominal outer dia pipes (as per DSR 18.8)

20mm nominal outer dia pipes (as per DSR 18.8.1)

25mm nominal outer dia pipes (as per DSR 18.8.2)

32mm nominal outer dia pipes (as per DSR 18.8.3)

Providing & fixing of hand lever operated forged brass body full way ball valve type isolating valve having forged brass hard chrome plated mirror finish ball, steel handle with PVC grip, teflon seat, screwed ends tested to a pressure of 15 kg/sqcm complete. 15 mm nominal bore

20 mm nominal bore

25 mm nominal dia

32 mm nominal bore

40 mm nominal bore

50 mm nominal dia

Providing & fixing brass ball float valve with bronze floats of approved quality complete. 40 mm nominal dia

Providing & fixing of medium class G.I.spout up to 300 mm. length including cutting and making good the walls and floors etc. as required. a) 25 mm dia

Supply & fixing in position ISI marked cast iron double flanged butterfly valves (PN 16 MPa) as per IS:13095, with SS disc, shaft, seating rings, internal fastening, nitrile rubber lining, nuts, bolts including transporting to worksite, 3 mm thick rubber gaskets etc. including testing, Complete as per drawings & directions of the Engineer-in-charge. 65 mm dia

100 mm dia

Excavating trenches of required width for pipes, cable, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.50m including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. (as per DSR 2.1) All kinds of soil (as per DSR 2.1) Pipes cables etc. exceeding 80 mm dia. But not exceeding 300mm dia. (as per DSR 2.1)

Providing, laying and jointing glazed stone ware pipes grade class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1cement :1 fine sand) including testing of joints etc complete. (as per DSR 19.1) 150 mm diameter (as per DSR 19.1)

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 gradded stone aggregate 40 mm nominal size) alround S.W. Pipes including bed concrete as per standard design. (as per DSR 19.2) 150 mm diameter S.W.Pipe (as per DSR 19.2)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. (as per DSR 19.6) 250 mm. dia. RCC Pipes (as per DSR 19.6)

Providing and laying in position cement concrete excluding the cost of centering and shuttering. (in all type of work upto plinth level) by 1:4:8 (1 cement : 4 coarse sand : 8 graded stone agg. 40 mm nominal size) (as per DSR 4.1.8)

Providing and laying in position cement concrete excluding the cost of centering and shuttering (in all type of work upto plinth level) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) for RCC bedding (as per DSR 4.1.3)

Constructing brick masonry manhole in cement mortar 1 : 4 (1 cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design (as per DSR 19.7) Inside size 90 x 80 cm & 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensions, total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) (as per DSR 19.7) With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 (as per DSR 19.7) Inside size 120 x 90 cm & 90 cm deep including CI cover with frame (Medium duty) 560mm internal diameter, total wt. of cover & frame to be not less than 208 kg (wt. of cover 108 kg and wt. of frame 100 kg) (as per DSR 19.7)

With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 (as per DSR 19.7.3.1) Extra for depth for manholes: (as per DSR 19.8) size 90 X 80 cm (as per DSR 19.8.1)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (as per DSR 19.8.1.1) size 120 X 90 cm (as per DSR 19.8.2)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (as per DSR 19.8.2.1)

Providing and fixing square mouth S. W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design (as per DSR 19.4) 180 x 150 mm. size P type (as per DSR 19.4) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (as per DSR 19.4)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar (as per DSR 19.15)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 250 mm. dia. RCC Pipes (as per DSR 19.6)

Providing and laying in position cement concrete excluding the cost of centering and shuttering. (in all type of work upto plinth level) by 1:4:8 (1 cement : 4 coarse sand : 8 graded stone agg. 40 mm nominal size) (as per DSR 4.1.8)

Providing and laying in position cement concrete excluding the cost of centering and shuttering (in all type of work upto plinth level) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) for RCC bedding (as per DSR 4.1.3)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class esignation 7.5 (as per DSR 19.27)

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (as per DSR 19.29)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : (as per DSR 19.15) With 20x20 mm square bar (as per DSR 19.15)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore (as per DSR 18.12)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm diameter pipe (as per DSR 18.4)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia (as per DSR 18.59)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore (as per DSR 18.17)

50 mm nominal bore (as per DSR 18.17.4)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering (for thrust blocks at bends and junctions of water lines ) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) (as per DSR 4.1.3)

Providing and fixing G.I. Union in GI pipe including cutting and threading the pipe and making long screws etc. complete(New work) 40 mm nominal bore (as per DSR 18.46)

50 mm nominal bore (as per DSR 18.46.6)

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality LD- 2.5 Rectangular shape 600*450 mm internal dimensions (as per DSR 19.19)

Constructing masonry gate valve Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (as per DSR 18.32)

Providing Precast Cement Concrete / SFRC Valve Chamber cover and frame conforming to IS : 12592-2002., The concrete mix should be not less than M 30. L D- 2.5 Rectangular shape 600*450 mm internal dimensions (as per DSR 19.19)

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : (as per DSR 18.34)

Supply, laying, jointing, testing and commissioning of ISI marked H.D.P.E. pipes (PE 100) as per IS : 4984, including transportation upto the site, jointing by electro fusion welding for upto 110 mm dia pipe and butt fusion welding for above 110 mm dia pipe, providing and fixing all fittings i.e. bends, tees, couplers, junctions, tapers, reducers, adopters, end caps, flanges with nut and bolts for fixing of appurtenances complete in all respects. Upto 110 mm dia pipe will be supplied in coils only. 110 mm. OD. (PN 8)

Supply, fixing in position, testing ISI marked cast iron double flanged sluice valves as per IS:14846-2000, (PN 10) with SS stem, bolts, nuts, 3 mm thick rubber gaskets including transporting to worksite, Complete as per drawings & directions of the Engineer-in-charge. 100 mm nominal dia

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) for thrust blocks at bends and junctions of water lines including necessary excavation, centering, shuttering etc as directed and required at site to complete the work..

Providing, fixing, jointing and testing in position ISI marked (IS : 1239) G.I pipes (Heavy class-C) manufactured from seamless pipes, complete with all necessary G.I fittings i.e. sockets, elbows, tees, bends, reducers, unions, plugs, supports, clamps, Hangers. The Galvanization shall conform to IS : 4736. The work shall include the painting with two coats enamel paint of approved quality and shade over a coat of primer on exposed pipe works, complete as required by the Engg-in-charge for proper completion of the work. 50mm nominal bore (wall thickness - 4.5 mm)

40mm nominal bore (wall thickness - 4.8 mm)

Providing and fixing in position M.S. / G.I. pipe one side flanged sleeves of suitable long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. 50 NB (IS 1239 - C Class)

65 NB (IS 1239 - C Class)

150 NB (IS 1239 - C Class)

200 NB (219.1 OD) (IS: 3589, 6.3 mm thick)

Providing and fixing in position M.S. / G.I. pipe both side flanged sleeves of suitable long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. 50 NB (IS 1239 - C Class)

65 NB (IS 1239 - C Class)

100 NB (IS 1239 - C Class)

150 NB (IS 1239 - C Class)

Providing and fixing in position M.S. / G.I. pipe one side screwed sleeves of suitable long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. 50 NB (IS 1239 - C Class)

65 NB (IS 1239 - C Class)

80 NB (IS 1239 - C Class)

Supply & fixing in position ISI marked cast iron double flanged butterfly valves (PN 16) as per IS:13095, with SS disc, shaft, seating rings, internal fastening, nuts, bolts including transporting to worksite, 3 mm thick rubber gaskets etc. including testing, Complete as per drawings & directions of the Engineer-in-charge. (MAKE : Venus / IVC / SKS / Zoloto / Audco / Advance) 50 mm nominal dia

65 mm nominal dia

Providing & fixing cast iron body strainer made up of SS screen tested to a min. pressure of 15 kg/sqcm complete with flanged ends as required. (make : CIM / Zoloto / Audco / Advance) 50 mm nominal bore

Supply, installing, testing and commissioning of non clog submersible type drainage / dewatering pump suitable for automatic operation, float valve operated, automatic / manual operation, including NRV & all accessories, nlet & outlet arrangements, required cable etc. complete in all respects. (Make : Grundfos / ITT / WILO / DP / Nocchi / KSB) 2.5 lps at 12 meter, 10 mm max particle size, 50 Hz, 240 volts, IP 68, F insulation, Float level switches, impeller in CI / Polypropylene, casing in CI / polyurethan and shaft in stainless steel (1 set comprises of two number dewatering pumps - for pump house drainage)

Providing, fixing, testing and commissioning of single stage, horizontal, centrifugal, 2 pole, single/three phase, 50 HZ, AC, monoblock pump (as per IS) incorporating C.I. casing and frame, carbon steel shaft, bronze shaft sleeve mounted on greese lubricated deep groove ball bearings, cast iron impeller, TEFC induction motor directly coupled to the pump, IP44 protection, class B insulated, hydraulically and dynamically balanced to give vibration free operation, with mechanical seal arrangement, fixed on a base plate with suitable vibration eleminator pads complete with RCC foundation, bolts grouted in 100 mm thick CC blocks of 1:2:4, complete with pressure gauge on the delivery side including provision of foot valve, non-return valve, isolating valves, strainer on suction and delivering sides as required, suction and delivery headers complete in all respects. (The cost of necesary pipes and valves shall be seperate). The duty of pump shall be - (Make : Kirloskar / Mather+Platt / Crompton Greaves) (i) Treated Water Transfer Pumps - 2 nos (1W+1S), having discharge : 4500 lit/hr (each) at 40 meter head (1 set comprises of 2 number pumps)

a. Transporttation of Rig Machine

b.Erection and Dismantling of Rig machine

Water supply changes and drilling fluid

Drilling 200 mm dia bore hole in alluvium other than rock sand stone & boulder formations From G.L to 500 M

Reaming of 200 mm dia bore to 675 mm dia bore from G.L to 100 M.

Reaming of 200 mm dia bore to 500 mm dia bore from 100 to 500 M

Washing of bore hole

Electric Logging of bore hole

Providing & lowering of assembly pipe including cutting & welding by providing a collar: a. 200 mm dia MS ERW Housing pipe having wall thickness 7mm 60M

b.150 mm dia MS ERW Blind pipe having wall thickness 7MM 300 M

c. 150 mm dia MS ERW slotted pipe having thickness 7 mm 60m

Providing & fixing well cap, Reducer, clamp center guide & Ball Plug

Providing and Packing the bore hole with suitable size of pea gravel 100 M3

Development by air compressor 600 PSI a. Transportation of air compressor 1 job

b. Erectin of air compressor 1 job

c. Running of air compressor 50 Hrs

Water testing chemical and bacteriological

Supply and installation of 7.5 H.P submersible pump set with 500 LPM discharge complete column pipes with fittings 1 job

ELECTRICAL WORKS WIRING ( with Modular type switch,sockets,GI boxes ) Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash.

Wiring for group controlled (looped) light point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring point for call bell with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting complete with 14 SWG copper earth continuity wire GP Box and piano type bell push or 2 pin socket etc, complete in all respect including matching colour wash.

Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash.

Supply and wiring of submain with three number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia. heavy guage rigid steel conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with 2 no. 14 SWG copper earth continuity wire etc, complete in all respects including matching colour wash. ( Circuit for 15 A Sockets and 5 A sockets including looping)

Supply and wiring of submain with two number 1.5 Sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit partly laid in slab along with reinforcement before concerting and partly concealed in wall, with one no,. 14 SWG copper earth continuity wire etc. Complete in all respect including matching color wash.

Supply and wiring of 3 number 4 sq. mm. FRLSH PVC insulated 1100V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit partly concealed in wall & partly laid in slab along with reinforcement before concreting, with two number 14 SWG copper earth continuity wire including matching colour wash etc, complete in all respect ( Circuit for AC or Geyser sockets)

Supply and wiring of 3 number 6 sq.mm. FRLSH PVC insulated 1100V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with two number 14 SWG copper earth continuity wire, including matching colour wash etc, complete in all respect. ( Sub mais of UPS DB's) and for 32 A wather proof box for VAV

Supply and wiring of 4 number 6 Sq.mm FRLSH PVS insulated 1100 V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit on surface, with two number 14 SWG Copper earth continuity wire etc. complete in all respect.

Supply and wiring of 4 number 10 Sq.mm FRLSH PVS insulated 1100 V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit on surface, with two number 10SWG Copper earth continuity wire etc. complete in all respect.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. ( 5/6 A Outlets)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. ( FOR AC and GEYSER POINTS)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

TV antenna socket outlet

Data Socket Outlets

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) ( For TV Telephone Data Sockets )

Supplying and fixing Blanking Plate modular plate in exising face plate/Gi Box as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

2 run of cable

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 150 mm X 150 mm X 60 mm deep ( Junction boxes for LV systems as required )

SH II : Distribution Boards and Conduit S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve CAT B (Outgoing MCB's)

S&F of 20 Amp. DP MCB (10 KA) C Curve CAT B ( As incomer of UPS DB )

S&F of 63 Amp FP MCB CAT B ( As incomer of LDB and PDB )

S&F of 200 Amp 3 pole MCCB (25 KA) Thermal Magnetic release

S &F of 80-100 Amp 3 pole MCCB (16 KA) Thermal Magnetic release

S&F and making connection of 25A 2 pole 30mA ELCB/ RCCB of Din Rail Mounting complete in all respect as per direction and satisfaction to the Engineer in charge.

S&F and making connection of 63 Amp. 4 pole 30mA ELCB/RCCB of Din Rail Mounting complete in all respect as per direction and satisfaction to the Engineer in charge.

S & F surface/Flush mounting 8ways SPN distribution board without additional metal door without MCB complete in all respect, as direct by Engineer in Charge. CAT B

S & F surface/Flush mounting 4ways TPN distribution board with additional metal door without MCB complete in all respect,as directed at site by Engineer in charge. CAT B

S & F surface/Flush mounting 8 ways TPN distribution board with additional metal door without MCB complete in all respect,asdirected at site by Engineer in charge. CAT B

S & F surface/Flush mounting 12 ways V TPN distribution board with additional metal board without MCB complete in all respect,as directed at site by Engineer in charge. CAT B

S & F surface/Flush mounting weather proof enclosure suitable for mounting 100 A TP MCCB , including Supply and fixing 1 no 100 A TP MCCB ,16 Ka making connections etc complete as required ( For VRV)

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

25 mm ( For telephone, TV, Data wiring)

SH III : Fans and Fittings Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AA

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. CAT-A

Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. CAT-AA

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 40 to 50 Watt. Confirming to IP 65 protection complete in all respect. CAT-AA

Supply and fixing of buzzer on polished MDFEG / Teak ply board including making connections etc. complete in all respect.

Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. ( For toilets , circuits)

Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. (For Cabins, halls with each switch board)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supply, Installation, Testing and Commissioning of 300 mm sweep, low spped ,double ball bearing, exhaust fan with bird screen and all accessories suitable for 230 V, 50 Hz, single phase AC Supply including making necessry hole in wall/glass/plywoood, 12 mm Plywood fixing as required , grouting nut/bots in wall, washers, , earthing etc. complete as required

Supply and Fixing 400 Amp TPN Sandwich aluminium bust bar trunking complete shutable for IP 54 protection with top end cover plate of 1.6mm thik G.I. Sheet with suitable arrangement for fixing etc Complete in all respect.

Supply and Fixing 630 Amp TPN Sandwich aluminium bust bar trunking complete shutable for IP 54 protection with top end cover plate of 1.6mm thik G.I. Sheet with suitable arrangement for fixing etc Complete in all respect.

Supply and Erection of Incoming adopter box for mounting 400 Amp. TPN CFS unit including connecters of requirement capacity on to the rising mains complete in all respect

Supply and Erection of Incoming adopter box for mounting 630 Amp. TPN CFS unit including connecters of requirement capacity on to the rising mains complete in all respect

Supply and Fixing of bend for 400 Amp Sandwich A1 bus for trunking complete in all respect.

Supply and Fixing of bend for 630 Amp Sandwich A1 bus for trunking complete in all respect.

Supply of L.T. Control Panel, indoor cubical type dust & vermin proof, floor mounting, free standing, dead front construction, made of 16 SWG CRCA sheet steel duly Powder Coated and complete with the following switchgears, meters & accessories of ABB / L&T or equivalent Make including connections & interconnections etc. complete in all respects. Incoming 400 Amp. MCCB-1 No. Outgoing as per site requirement.

Supply of L.T. Control Panel, indoor cubical type dust & vermin proof, floor mounting, free standing, dead front construction, made of 16 SWG CRCA sheet steel duly Powder Coated and complete with the following switchgears, meters & accessories of ABB / L&T or equivalent Make including connections & interconnections etc. complete in all respects. INCOMER 630 Amp. MCCB-1 NOS. Outgoing as per site requirement.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all round and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clapms etc. of suitable size or as directed by the engineer Incharge, Complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 185 sq.mm X 3.5 core

400 Sq.mm X 3.5 core

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. completed in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer- Incharge. 185 sq.mm X 3.5 core

400 Sq.mm X 3.5 core

Supply and fixing of plain or pin type copper tin plated cable socket (Lug) to the cable leads, insulating with tape and making connecting etc. complete in all respect as per direction of Engineer-Incharge. 95 Sq.mm

Supply and burring of Safe Earting Electrode T-39 (Hot-Dip Galavanized), Length 3000 mm, outer pipe 76 mm inner Dia 38 mm terminal Dia 12 mm, outer GI Pipe of 16 SWG and inner GI Pipe of 12 SWG with Hot Dip Galavanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) cable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. ( From electrode terminal to switch board, cost of 25 X 3 GI. Strip will be extra.) Make As: As approved in U.P.P.W.D., & C.P.R.I, Certified.

Supply and laying of 32 mm X 6 mm G.I. Strip from earth electrode directly in the ground as required complete in all respect.

LIGHTING ARRESTOR Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing.

Supply and fixing of horizontal air termination (roof conductor) of 25mm x 3mm G.I. strip, G.I. clamps on surface complete in all respects as approved by Engineer-in-charge.

Supply and fixing of vertical air termination final rod comprising of 300mm long x 25mm dia. GI rod with one pointed prong and 100mm dia x 3 mm thick base plate etc. complete in all respect.

Supply and fixing of vertical down conductor of 32mm x 6mm G.I. strip etc. on approved clamps on surface for lightning conductor complete in all respects (for Five and above storeyed Buildings).

Supply and fixing of testing joint of G.I. strip 32mm x 6mm and 150mm long with G.I. bolts and nut etc. complete in all respect.

Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect

PUMP POUSE SH I: WIRING ( with Modular type switch,sockets,GI boxes) Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash.

Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash.

Supply and wiring of submain with three number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia. heavy guage rigid steel conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with 2 no. 14 SWG copper earth continuity wire etc, complete in all respects including matching colour wash. ( Circuit for 15 A Sockets and 5 A sockets including looping)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) ( For TV Telephone Data Sockets )

Supplying and fixing Blanking Plate modular plate in exising face plate/Gi Box as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 150 mm X 150 mm X 60 mm deep ( Junction boxes for LV systems as required )

SH II : Distribution Boards and CONDUIT S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve CAT B (Outgoing MCB's) )

S&F of 20 Amp. DP MCB (10 KA) C Curve CAT B ( As incomer of UPS DB )

S&F and making connection of 25A 2 pole 30mA ELCB/ RCCB of Din Rail Mounting complete in all respect as per direction and satisfaction to the Engineer in charge.

S & F surface/Flush mounting 8ways SPN distribution board without additional metal door without MCB complete in all respect, as direct by Engineer in Charge. CAT B

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 8 way, Double door SPN MCBDB

SH III : FANS and Fittings Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. CAT-A

Supply and burring of Safe Earthing Electrode T-39 (Hot-Dip Galvanized), Length up to 3000mm, outer pipe 76mm inner Dia 38mm terminal Dia 12 mm ,outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with HotDip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 X 3 GI. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified.

Supply and laying of 32 mm x 6 mm G.I. strip from earth electrode directly in the ground as required complete in all respect

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supply, Installation, Testing and Commissioning of 300 mm sweep, low spped ,double ball bearing, exhaust fan with bird screen and all accessories suitable for 230 V, 50 Hz, single phase AC Supply including making necessry hole in wall/glass/plywoood, 12 mm Plywood fixing as required , grouting nut/bots in wall, washers, , earthing etc. complete as required

GUARD ROOM SH I: WIRING ( with Modular type switch,sockets,GI boxes) Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash.

Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash.

Supply and wiring of submain with three number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia. heavy guage rigid steel conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with 2 no. 14 SWG copper earth continuity wire etc, complete in all respects including matching colour wash. ( Circuit for 15 A Sockets and 5 A sockets including looping)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. ( 5/6 A Outlets)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve CAT B (Outgoing MCB's) )

S&F of 20 Amp. DP MCB (10 KA) C Curve CAT B

S&F and making connection of 25A 2 pole 30mA ELCB/ RCCB of Din Rail Mounting complete in all respect as per direction and satisfaction to the Engineer in charge.

S & F surface/Flush mounting 8ways SPN distribution board without additional metal door without MCB complete in all respect, as direct by Engineer in Charge. CAT B

Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-A

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. CAT-A

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable Monitor module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

SH: PA SYSTEM Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

SH : CABLING , CONDUIT & WIRING Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. ( For basement on surface)

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

speaker cable Two pair, 2-core, 1.5 sqmm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 1.5 sq. mm

4 x 1.5 sq. mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

PUMPS (a) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (c) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(e) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 70 m Head ( For Hydrant and Sprinkler )

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (b) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (c) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (d) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm at 70 m Head

(a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, (d) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 70 m Head

(a) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class- 'F' insulation, conforming to IS-325. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. (f) Suitable Electrical Starter panel for the pump 450 lpm at 35 m Head

PIPES & ACCESSORIES Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 40 mm dia ( for primary reel connectiomns)

80 mm dia ( for jocky pumps and terrace )

80 mm dia ( for FHC and drain lines)

100 mm dia ( for Terrace pump)

150 mm dia ( for Main pumps ,diesel pumps and FBC)

200 mm dia ( suction header for maintenance)

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 40 mm dia ( for primary reel connectiomns)

80mm dia ( for Press and terrace Pumps)

150mm dia ( For main and diesel PumpS0

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80 mm dia

150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m length

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe ( inlet)

3 way - 150 mm dia M.S. Pipe ( outlet)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100mm dia

Providing Annunciation cum monitoring Panel for minimum 10 no Flow switches , and having maintenance free battery back up for 48 hours , batteey charger , including making connections etc as required

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150mm dia

SH I: CABLING Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 6 sq. mm 2 core

35 sq. mm 3.5 core

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. 6 sq. mm 2 core

35 sq. mm 3.5 core

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 6 sq. mm

SH : EARTHING and Lightning Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. ( Loop earthing for street light poles etc)

SH: BOARDS Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel complete in all respects. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be of cat A & B Only. Street Light Feeder Pillar Outdoor Cubicle type Incoming- 63 Amp MCCB -1 No, 4 strip Auminium Sleeved BUS BAR : 100 Amp Outgoning for Misc - 32 A TPN MCB alongwith space for fixing starter/meter as required : 2 no Outgoning for Street Light - 32 FP MCB +ELCB , 32 A 4 Pole contactor and Astraunimical timer- 1 set 10 A DP MCB: 4 no

SH: POLES FITTINGS Supply & fixing of 5 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 160 mm and base plate 12mm thik) having 3mm thickness with single arm bracket (0.5 Mtr length) , having built in cable end box, connector , 6 A SP MCB etc as rquired on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 70 Watt. Confirming to IP 66 protection complete in all respect. CAT-AA

Supply and drawing following Sizes of FRLS PVC insulated copper conductor single core cable in the existing surface /recess steel/pvc conduit as required 3*1.5 Sqmm ( from Cable end box of pole to Street light fitting )

HVAC WORK Supply, Installation, Testing & Commissioning of factory fitted mircoprocessor based self diagnostic auto check VRF system outdoor unit equiped with PCBs, accumulator, oil seperator, burshless DC inverter fan motor, OEM self manufactured hermetic sealed multi valve scroll type compressors. Compressor should be based on low pressure shell technology for longer life with integrated IPM & PWM to ensure effective operation even at low/partial load conditions for better efficiencies. Compressor shall be fixed in metallic chamber for lower noise with enhanced fire saftey protection. Outdoor unit shall be equiped with highly efficient induction type heater using eliminated wasted heat. VRT/VET system shall be based on advanced & automatically modulation evaporating refrigerant temperature between 3°C to 11°C for instant cooling and better energy effiency as per user's demand. Heat exchanger must be essentially equiped with internally grovved copper tubes for better heat exchange performance and operate in extreme conditions i.e. even at ambient temparature of 50°C or more. All outdoor shall have approximately following as per OEM standards rated capacities at ARI conditions and, with the criteria of delivering 95% +/- 20 HP Heat Pump Unit Single Module Type Unit

Connecting Kit

Supply, Installation, Testing and Commissioning of VRF indoor units with factory fitted electronic expansion valve, multi speed fan motors, dynamically balanced blowers, synthetic washable plasma media filter with hydrophobic coating on cooling coil. Electronic components like PCBs must be essentially enclosed in a metal box compartment being integrated part of indoor unit to ensure enhanced fire protection with auto by pass technology allowing uninterupted operation of indoor units connected to a circuit in event of break down in any indoor connected to same circuit. All indoor units shall have individual fan speed and temperature control mechanism to be operated from corded/cordless remote. In addition to all indoor units can also be operated from central remote control. Ceiling Mounted Cassette Units 4.13 TR Cassette Type Indoor Cnit

3.33 TR Cassette Type Indoor Unit

2.65 TR Cassette Type Indoor Unit

1.65 TR Cassette Type Indoor Unit

1.33 TR Cassette Type Indoor Unit

Supply, Instalaltion, testing and commissioning of Y/T-joints.

Supply, Installation, Testing & Commissioning of Corded Self Diagnostic Type Remote Controllers.

Supply. installation testing and commissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R 410A duly insulated with elastomeric nitrile rubber type tubular insulation and hanger/channel support between indoor & outdoor units as per specifications. 41.3 mm O.D.

Supply, installation, testing and commissioning of PVC condensate drain water piping complete with fittings like elbows, tees, reducers, bends, supports, insulation etc. as required and of following sizes. 32 mm dia pipe, Insulation Thickness - 9 mm

40 mm dia pipe, Insulation Thickness - 9 mm

50 mm dia pipe, Insulation Thickness - 9 mm

Supply & fixing of UV Treatment for Exposed piping with Glass Cloth covered with UV Paint.

Providing & fixing of control cum trans-mission wiring of copper between indoor and outdoor unit in 25 mm PVC Conduit. 2C x 1.5 Sq mm

Supply, fabrication & Erection of MS stand including foundation complete is all respect.

Supply, installation, testing and commissioning of electrical panel complete with 225A incomming MCCBs with metering & 4 Nos. 63A MCBs/RCBs of suitable ratings complete in all respect for Outdoor Units.

Supply, installation, testing and commissioning of electrical panel complete with 63A incomming MCCBs & 20 Nos. 6A MCBs of suitable ratings complete in all respect for Indoor Units.

Supply, installation, testing and commissioning of electrical Cabl for indoor and outdoor units and also for incoming supply to electrical panel 4 core X 10 Sqmm Copper Cable

3 core X 2.5 Sqmm Copper Cable

3.5 core X 150 Sqmm Al. Armoured Cable

3.5 core X 95 Sqmm Al. Armoured Cable

GENERATING SET DIESEL ENGINE DRIVEN WITH AMF PANEL Providing, Installing, Testing and Commissioning of Silent Type Diesel Generating sets with Acoustic Enclosure having Prime continuous Power Rating of 400 KVA at 1500 RPM, 0.8 lagging power factor at 433 V suitable for 50 HZ, 3 phase system and consisting of the followings: Diesel Engine- Diesel engine 4 stroke Radiator cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 1500 RPM, at 40 Degree C, 50% RH & at 1000 Meter MSL and conforming to BS 5514, BS 5000, IS 10000, IS 3046, capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories Engine mounted Instrument Panel fitted with and having digital display for following: a). Start-Stop switch , b). Battery charging indication, c). RPM indication, d). Over speed indication e). Low lub. Oil trip indication, f). Engine Hours indication, g). Lubrication Oil Pressure Indication, g). Lubrication Oil Pressure Indication, h). Water Temperature Indication i). Lubricating Oil Temperature Indication, j). Generator Control Panel/Power Command Centre, k). Battery charging indications Alternator - Synchronous alternator 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be suitably derated to give continuous output of 250 KVA at 40 Degree Cel with 10% overload .The alternator shall be having SPDP enclosure, brushless, continuous duty, self excited, self-regulated through AVR conforming to IS : 4722/ BS 2613 suitable for tropical condition and with class-F or better insulation. Base Frame & Foundation - Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer. Fuel Tank and Fuel Piping - Daily service fuel tank of 990 litres capacity fabricated out of 3 mm thick M.S.sheet in rectangular shape complete with inlet, outlet, overflow, drain, vent with flame arrestor and all standard accessories, structural support etc. complete as required and fuel piping between fuel tank and diesel engine with suitable dia MS "C' class pipes confirming to IS 1239 (Part 1 ) complete with valves, level indications & accessories as required as per specifications. Exhaust System - Dry exhaust manifold of suitable dia, welded black MS 4.3 mm thick pipe confirming to IS:3589 cut to required lengths (max. 3 mtr) and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with mineral wool/Rockwool, 10 mm thick wire mesh and 0.6 mm thick aluminium cladding etc. Flexible stainless steel below as required as per specifications with Hospital grade type silencer Starting System - 24V DC Starting system comprising of starter motors: Voltage regulator and arrangement for initial excitation complete with suitable nos. of SMF batteries (capacity of each batteries shall be as per standard manufacturer practice to suit min. three attempt starting facility) with battery charger as required as per specification. Acoustic Enclosure - Acoustic enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere/ space where it is to be installed, meeting the CPCB norms as per specifications. DG Set as above

Supplying, fixing, testing and commissioning of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 250 mm dia x 4.3 mm nominal thick

Supplying, laying/ fixing, testing and commissioning of following thickness resin bonded fiber glass pipe section insulation having density 80 kg/cum or mineral wool (non combustible) having density of 144 Kg/cum duly covered with a layer of 120 gm/sqm polythene sheet (vapour barrier) on existing pipe and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date) at joints etc. as per specifications and as required. 65 mm

Design supply and Fabrication of MS STRUCTURE for Exhaust Chimney System/for Bus Trunking. Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top.On surface the cable run shall be fixed on M.S.clamps etc. of suitable size or as directed by the Engineer - Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 300 sq. mm 3-1/2 core

Supply and fixing of brass nickle compression gland for PVC nsulated &armoured served sheathed, underground cable including rubber ring etc.complete in all respect.The armouring of the cable shall properly connected with the earth as per direction of Engineer Incharge. 300 sq. mm 3-1/2 core

Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads ,insulating with tape and making connection etc. complete in all respect as per direction of the Engineer- Incharge. 150 Sqmm

LIFT S.I.T.C of 13 Passanger 544 Kg with automatic doors for G+4 floor complete in all respact 1.0 m/s speed. Steel door frame + lift well M.S Channel work & beam, trap door etc. AS Per CPWD Specification

Supplying, installation, testing and commissioning of Grid Connected Rooftop Solar Power Plants including transportation, insurance, five year AMC/CMC, and applicable fees and taxes. Solar panel as per UP ECBC Act 2018 50 kw

TRANSFORMER 11 KV/433 V VOLTAGE RATIO Supply ,installation ,testing and commissioning of copper wound 11KV/0.433 KV Distribution transformer ,LEVEL 2 outdoor type complete filled with oil, having cable end box at both sids ie for HT as well as MV side , with standard fittings , 3 phase, with OFF load tap changing , all as per latest IS , complete as rquired 630 KVA

HT SWITCH GEAR VACUUM CIRCUIT BREAKER (INDOOR) 11 KV HT panel 1 sections Supplying, installation, Testing and commissioning of indoor type floor mounted metal clad, 11 KV VCB Panel with air insulated but encapsulated copper bus bars of 1250 Amps current carrying capacity and fault level of 350 MVA, 3 Nos VCB totally enclosed and fully interlocked , horizontal draw out horizontal isolation type breakers as per IS 13118 as amended up-to-date and additional specifications, each having 630 amps current carrying capacity, single break trip free. mechanism, motorised charged and auto / manual closing breaker suitable for use on 11 KV, 3 phase, 50 Hz AC supply , with short circuit fault breaking capacity of 350 MVA complete with self contained, fully interlocked rack in and rack out mechanism, featured with mechanical ON/ OFF indicator, with hand trip device, spring release coil, shunt trip coil and auxiliary contacts of at least 6 NO and 6 NC, IBMS/ SCADA compatible , and equipped with following switchgear and accessories with respective VCB, connections suitable for 3 X 240 Sq mm XLPE Insulated 11 KV cable a). 1-Metal clad housing with truck/switch having 630 A TP integral VCB fault level of 350 MVA for 3 Sec with manually /electrically operated mechanism ( spring charged motor-230 VAC). No. Of spare Aux. Contacts in breaker shall be at least 6 NO & 6 NC b) .1 set of air insulated COPPER bus bar & chamber, c). 1 set of isolating plug and receptacle , d). 1 set of automatic safety shutter, e). 1 set of breaker control switch (TNC), f). 2 Nos. Two core CTs with CT ratio 60 / 5-5 A Specific cores shall be as given below:- a) CT-1 (core-1: class 0.2s for metering, core-2: class 5P20 , b) CT-2 (core-1 & core-2: PS class) g). HT cable joint box for 1 no 3cx 240 sq.mm aluminium conductor XLPE cable (11 KV earthed) h). One set of 3-No's P.T'S 11/0.11 KV of (100 VA) cast resin type with protection fuses on both sides i). 1-No tripping coil & closing coil 24V DC /110 V A.C. , j). 1-set ON/OFF /Trip & Circuit healthy and phase indicating lights. k). 1 no microprocessor based numeric relay with O/C EF & SC with high set element relay , m). 1 no Master Trip Relay , n). 1 no Lockout Relay , o). 1-No Circuit supervision relay , p). Differential cum distance relay. , A). INCOMER

- - Do - - but 11 kva Outgoing

2 POLE& STRUCTURE WITH STEEL POLE Supply & erect 2 pole structure on 11 meter steel tubular pole consisting of pole with anti-climbing device, PCC foundation & cross arms etc for one incoming and one out going.

LIGHTNING ARRESTORS Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

GANG OPERATED AIR BREAK SWITCHES (GOD) Supply and fix HT 11 KV, out door type gang operated air-break switch suitable for horizontal or vertical mounting fixed type complete with 12 insulators of rating upto 200 Amps

Supply and laying of 3 core standered aluminium conductor XLPE (Cross linked polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. The armouring of cable shall be properly connected with earth conductor by clamps etc. 240 sq. mm 3 core

Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Essential Panel Section 1 for 400 KVA DG set INCOMER - 4 POLE 630 A ON LOAD change over switch 2 nos. 630 Amps 50 kA 440 volt FP MCCB, thermal release with overcurrent and short circuit releases complete with: 1 nos 630/5A Class - 1.0, 15 VA Burden CT's for metering 96 sq mm flush mounting 0-1250 Amp Digital Multi function meter with RS 485 port ON / OFF indicating lamps with MCB as backup protection. BUSBAR Electrolytic high conductivity aluminium three phase and neutral busbars rated at 1000 amps, 35 KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.2 sq.mm / amp. Neutral Bus Bar shall be 100% of Phase Bus Bar. OUTGOINGS- 1 Nos each comprising of 1 nos. 300 Amps 25 kA 440 volt FP MCCB, thermal release with overcurrent and short circuit releases complete with: 1 nos 300/5A Class - 1.0, 15 VA Burden CT's for metering ON / OFF indicating lamps with MCB as backup protection. OUTGOINGS- 2 Nos each comprising of 1 nos. 200 Amps 25 kA 440 volt FP MCCB, thermal release with overcurrent and short circuit releases complete with: 1 nos 200/5A Class - 1.0, 15 VA Burden CT's for metering ON / OFF indicating lamps with MCB as backup protection. OUTGOINGS- 21 Nos ( 3 in each compartment) each comprising of 1 nos. 40 Amps 10 kA 440 volt TP MCCB, thermal release with overcurrent and short circuit releases complete with:

Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing (This will apply for earthing of poles also).

Supply and burying earth electrode for lighting conductor of 900mm x 900mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe for watering funnel, 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineerin-charge complete in all respect.

Supply and burying earth for lighting conductor of 900mm x 900mm x 3mm copper plate vertically with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe for watering funnel, 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respect.

Supply and laying of 32 mm x 6 mm G.I. strip from earth electrode directly in the ground as required complete in all respect

Supply and laying of 32mm x 6mm copper strip from earth electrode directly in the ground as required complete in all respect.

SAFETY ITEMS Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality.

Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work.

Supply and fixing danger board fabricated from 10 gauge M.S. Sheet as per I.E. Rules.

CABLES Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sq. mm 2 core ( For DB etc in pump room

35 sq. mm 3-1/2 core ( For Pressurization terrace pump)

150 sq. mm 3-1/2 core ( For Hydrant pump)

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. 10 sq. mm 2 core

35 sq. mm 3-1/2 core

150 sq. mm 3-1/2 core ( For Hydrant pump)

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 10 sq. mm

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

EARTHING Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing.

Supply and fixing of testing joint of G.I. strip 32mm x 6mm and 150mm long with G.I. bolts and nut etc. complete in all respect.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

Deduct in item no. 501 (I) 501 (t) and 506 (a) to (f) when cables is passed through G.I./M.S. or Hume pipe in road crossing or along the wall. The cost of the G.I. pipe, hume pipe is to be extra when and where required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

SAFETY ITEMS Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality.

Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work.

Supply and fixing danger board fabricated from 10 gauge M.S. Sheet as per I.E. Rules.

SH : EARTHING Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing.

Supply and burying of 600mm x 600mm x 3mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG copper wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and copper wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. complete in all respect.

Supply and laying of 32mm x 6mm copper strip from earth electrode directly in the ground as required complete in all respect.

Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect

Fire EXTINGUISHERS Supply and fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of fire bucket, round bottom made of G.I. sheet 9- 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge.

M/S R.P. SINGH AND COMPANY

BLG CONSTRUCTION SERVICES P LIMITED