CWEAFJ-34/2021-22 SPECIAL REPAIR TO CERTAIN LIVING-IN BILLETS AT AF STN PATHANKOT

Amount

B/R Portion

Cutting openings, through brick walls built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hardcore, etc., to store and rubbish not exceeding 50metres complete all as specified and as directed.

Demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc all as specified.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, but except bricks i.e. using serviceable bricks ibtained from demolition, all as specified and directed.

Precast cement concrete louvres and Jallies 40mm thick (measured solid), Type B-0 1:2:4 using 12.5 mm graded crushed stone aggregate set in cement mortar 1:4, complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position and removing rubbish from the site, complete all as specified and directed.

Reinforced Cement Concrete type B-1 1:2:4 using 20mm graded crushed stone aggregate as in slabs, roof projection etc., complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exceeding 5cm but not exceeding 10cm widefor rough finished surfaces of concrete, complete all as specified and as directed.

TMT bars 8mm dia and over, cut to length bent to shape including binding with MS annealed wire of dia not less than 0.90 mm, complete, all as specified and as directed.

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

Rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:3 in Fascia or edging of Chajjas, Ceiling and Roof projections etc., including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cement, complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving (un-reinforced) exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

75mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc., finishing surface even and fair without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed. Note : The concrete shall be laid at a stretch not exceeding 3.0m in length and joint shall be made at every turning / corners, complete all as specified and directed.

40mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in floors etc., finishing surface even and smooth without using extra cement, complete as specified and directed.

Non-skid coloured glazed, joint free, ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 300mm x 300mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Glazed ceramic coloured, joint free, wall tiles in any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) in vertical surfaces of size 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

18mm to 20mm thick of size not less than 53 x 53cm, machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing, over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 all as specified and as directed.

16mm to 18mm thick, machine cut Kota stone as in skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and rounding off edges complete with mirror finish polishing, over and including 10mm thick screed bed or bedding layer of cement mortar 1:4 all as specified and as directed.

16mm to 18mm thick, machine cut Kota stone (full length) as in riser or steps, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and rounding off edges complete with mirror finish polishing, over and including 10mm thick screed bed or bedding layer of cement mortar 1:4 all as specified and as directed.

Granite Stone, 20mm thick, (table rubbed and polished) in platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in cement mortar 1:4 finished fair to received the granite including rounding the exposed edges, complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frames and in bed block for holdfast etc. similar work etc. complete all as specified and directed.

35mm thick 2nd class Hard wood factory made rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

35mm thick, 1st Class hard wood, factory made, glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

Factory made Steel Window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm including grill using 10Sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter of ERW section 50mm x 20mm and 1.0mm thick with two openable leafs having two Nos sash bar of T Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fittings welded to frame shutter complete all as specified and as directed :- (a) Hold Fast, 150mm long of Flat Iron 12mm x 3mm made to shape 04 Nos per window (b) Handle of Z-Section 20mm x 25mm, 100mm Long 01 No per Leaf (c) Stainless Steel Tower bolt 150mm long - 02No per leaf

(d) Z-section 20mm x 25mm, 100mm Long Stopper 1 No per Leaf (e) Cleat 55mm Long of Hollow Square 15mm x 20mm x 63mm welded to Hinge 01 No per Leaf (f) MS Pintal hinges of size 75mm x 12mm 02 Nos per Leaf including Stainless Steel Wire Cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with aluminium wire staples and glass pane 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint complete.

Factory made solid PVC Door Frame single rebated of size 60 x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws taking down with existing one complete all as specified and directed.

Factory made PVC Flush Door Shutter of 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 5.0mm thick moulded prelam PVC sheet on the front face and 5.0mm thick panel colour PVC sheet on back face complete all as specified and directed

Butt hinges, medium weight, Stainless Steel, 100mm size, complete all as specified and directed.

Stainless Steel, sliding door bolt with hasp, staple (bolt type) 250mm, and fixing clips of sheet and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 200mm long complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 150mm long complete all as specified and directed.

Stainless Steel handle complete of size 150mm long complete fixed in repairs complete all as specified and directed.

Brass 300mm spring for door, ordinary Rat Tail Rod pattern springs, including roller and roller plate complete fixed in repairs complete all as specified and directed.

4mm thick sheet glass ordinary quality and glazing with oil putty, wooden beads or fixed in aluminium window shutter in squares not exceeding 0.5 Sqm in each pane, including hacking out old broken glass, complete all as specified and as directed.

Stainless Steel Wire Cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Stainless Steel, 25 mm dia fancy type Curtain Rods fixed to brackets including brackets and fancy type corner ends complete all as specified and directed.

Cleaning of dust .Removal of all loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface with no loose material on surface . Repair all joints& cracks with Highly elastic Bituminous cold applied putty having penetration after setting upto 8mm . Leveling of Surface to give proper Slope will be done as per site requirements with Shalipatch cold applied ,Bituminous Mortar & Cold Emulsion cum Waterproofing Liquid --Shalikote -T-10. Create SSD condition on Surface with Water. Prime the surface with Tarfelt LM mixed with potable water in the ratio of 1 : 1 and apply @ 400 grm per Sqm ( As per Surface Conditions) • Apply first coat of Tarfelt LM having elongation 200% conforming to ASTM -C -412& having crack bridging of .8mm confirming to ASTM -C -836 with Tensile strength after 7 Days 0.50 mm conforming to ASTM-C-412 with no diluation of water on primed surface while the surface is still tacky with consumption of 700 gram per Sqm. Lay Geotex of 45 grams/Sqm Fibre mesh simultaneously and paste it properly with

overlap of 50mm .Allow the first coat to dry for 10 to 12 Hrs . • Apply 2nd coat on cured first coat with consumption @ 700 gram per Sqm in oppsite direction of first coat by Brush or Roller Allow it to dry for 10 – 12 hr after apply 3rd coat with consumption @ 700 gram per Sqm. • Ensure final curing time of 36 hrs before allowing / carrying out any further work. Conduct Ponding test after minimum 7 day ppplying two coats of U.V resistant Elastomeric Exterior Axcrylic Weather resistant waterproof coating - Shalicryl-215 - having elongation of 300% after curing of 14 Days confirming to ASTM D-6083 for U.V protection of bituminous elastomeric acrylic emulsified liquid membrane Tarfelt LM to give long life & prevent its deterioration from Sunlight. Note : Application of water proofing treatment will be done by Authorised Applicator only .

Rendering 12mm thick in cement mortar 1:3 on sunken concrete surfaces mixed with integral water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately under respective item.

Doctor Fixit Pidifin 2K high performance 2 component flexible Acrylic polymer modify cement base water proofing coating in two coat 1mm thick dry film mixed in ratio 2:1 by weight or 1.5:1 by volume product of M/S Pidilite Industry Limited complete all as specified and as directed.

Cement concrete type C-2 1:3:6 (using 40mm graded crushed stone aggregate) as in mass concreting in Sunken Floor, complete all as specified and directed.

Rotational moulded polyethylene Water Storage Tanks of capacity 1000 litres, (cylindrical vertical with threaded top), three layered, hoisted and fixed in position including supply and fixing necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, brass valve 20mm high pressure with polythene float and fly nut etc. complete, fixed in repairs, all as specified and directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 20mm dia bore iron pipe complete all as specified and directed.

Cutting chases, pinning in, making good to facing through brick wall where reqd and pointing in CM 1:3 to ends of edges of landing etc and cutting chases for concealed water tubing and making good cutting exc 10 cm but n.exc 20 cm girth, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 15mm dia complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 20mm dia complete all as specified and as directed.

Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed. Make : Jainko Cat Part No PCJ-1 / Prayag Cat Part No PS-02 / Cera Cat Part No F2002101

Bib tap with wall flange cast copper alloy chromium plated, fancy type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No BTJ-4 / Prayag Cat Part No 8606 / Cera Cat Part No F2008151

Stop cock / Angle valve with adjustable wall flange CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No AVJ-1 / Prayag Cat Part No 8910 / Cera Cat Part No F2002201

Stop valve, long cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No CSV-5 / Prayag Cat Part No 8718 / Cera Cat Part No F4060101

Brass chromium plated shower rose, fancy type, 100 - 150mm with swivel joints and fixed to steel pipe or union, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No FSJ-1 / Prayag Cat Part No BS-27 / Cera Cat Part No F7020306CH

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

Vitreous china wash hand basin, counter type size 550mm x 400mm, coloured, oval shape, flat back including 32mm bore brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm and adequate length, 15mm bore PVC connection pipe 450mm long with brass nuts on both side and fitting in granite slab with proper moulding etc., complete all as specified and as directed.

Vitreous china Urinal, Half Stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, beddding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screw, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and as directed.

PVC connection 45cm long fitted with two Nos of brass check nuts and washers complete, fixed to 15mm bore iron pipes, complete all as specified and directed.

Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minium weight 190 gms) complete all as specified and directed.

PTMT shelf with and including chromium plated brass screws and plastic cleats (Minimum weight 300 grams) complete all as specified and directed.

Grating Doom 100mm dia with waste hole of PTMT (Minimum weight 25 grams), complete, fixed in repairs, all as specified and as directed.

Cast Iron soil waste and vent pipe, sand cast, ISI marked 100mm bore, in any length with or without ears with lead joints laid in floor/walls all as specified.

Cast Iron soil waste and vent pipe, sand cast, ISI marked 75mm bore, in any length with or without ears with lead joints laid in floor/walls all as specified.

Cast Iron bends (any radius) diminishing pieces or tapers 100mm dia (larger bore measured) all as specified and as directed.

Cast Iron bends (any radius) diminishing pieces or tapers 75mm dia (larger bore measured) all as specified and as directed.

Cast Iron Branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100mm dia, all as specified.

Cast Iron Branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75mm dia, all as specified.

Cast Iron Branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100mm dia, all as specified.

Cast Iron Branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75mm dia, all as specified.

Cast Iron vent cowl, 100mm bore, complete all as specified and as directed.

Cast Iron vent cowl, 75mm bore, complete all as specified and as directed.

75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4 using 20mm graded crushed stone aggregate, fixed in repairs, all as specified and as directed.

Preparation new plastered or previously untreated surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

Preparation old plastered surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying two coats of white wash, complete all as specified and directed.

Complete removal of existing treatment on surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds moss and efflorosent salts, trading oil and greasy spots and applying two coats of acrylic exterior emulsion paint minimum four colours as approved of any shade / colour in camouflage pattern over a coat of primer including preparation of surfaces as per manufacturers instructions complate all as specified and as directed.

Preparation of newly plastered surfaces and applying two coats of acrylic exterior emulsion paint minimum four colours as approved of any shade / colour in camouflage pattern over a coat of primer including preparation of surfaces as per manufacture instructions complete all as specified and as directed.

Preparation new plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of old wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

E/M Portion

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including concealed conduit 20mm dia or more as per the site requirement including 1.50 Sqmm copper earth wire (green colour) FRLS Cable as earth continuity conductor connected to main earthing and common earth terminal for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sunken box for mounting switches etc. including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 92 here-in-before but for One light point controlled by two 2-way switches, complete all as specified and as directed.

All as per the description of Serial Item No 92 here-in-before but for one 3 pin socket outlet 05/06 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 92 here-in-before but for one 5 pin socket outlet 05/06 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 92 here-in-before but for one 3 pin socket outlet 15/16 Amp independent board using cable of size 2.5 Sqmm including 2.5 Sqmm copper earth wire (green colour) all as specified and directed.

Switch piano, flush type, 05/06 Amps, single pole, one way, complete all as specified and as directed.

Switch piano, flush type, 05/06 Amps, single pole, two way, complete all as specified and as directed.

Socket out let universal type, 2 in 1, 2 and 3 pin 05/06 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Switch piano, flush type, 15/16 Amps, single pole, one way, complete all as specified and as directed.

Socket outlet universal type, 2 in 1, 3 pin 5 and 15/16 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Electronic fan regulator stepped type with five steps 240 volts 100 watt suitable for 1200mm / 1400mm sweep AC ceiling fan, complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

LED Lamp 230 Volts 12 watts, in white colour with maximum Lumen output (850 lm) and colour temp 3000 K with base cap B-22, complete all as specified and as directed.

Tube light fitting, batten type suitable for and including LED 20 tube Rod 4' long with decorative colour in aluminum housing and integrated electronic driver and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed.

Decorative Bed side Light Fitting, wall mounting, decorative type, brushed nickel finish with opal glass diffuser, suitable for and including 1 x 07 Watts LED Lamp B-22 base, complete all as specified and as directed.

Taking down carefully existing Ceiling Fan / Exhaust Fan any type, servicing and spray painting of all the exposed surfaces of fan after cleaning all dust and scratching of old paint and painting with one coat of synthetic enameled paint and writing numbering in capital letters and refixing the same including making the electrical connections with PVC insulated, overall sheathed, flexible copper conductor cable complete all as specified and as directed.

Exhaust fan, metallic body, AC SP 230/240V, 300mm sweep with louver, 1400 RPM complete with accessories complete provisioning of three core flexible copper cord of size 23/0.0076 of required length from connector to fan for connection, including cutting hole for fixing exhaust fan to wall and making good the disturbed surfaces (including plastering in cement mortar 1:4, brickwork in cement mortar1:4: and two coats of distempering to match with the existing surface, complete all as specified and as directed.

Distribution Board iron clad TPN DB, double door with IP-43, IK-09 protection, Four Way, vertical, suitable MCCB TPN 415 Volts 63 Amps rating as incommer and MCB as outgoing complete with appropriate size copper busbar including cutting chases in walls for fixing the DB and making good disturbed surfaces of walls, complete all as specified and as directed. Note : MCBs / MCCBs shall be measured and paid separately under the respective item.

MCCB TPN 415 Volts 125 Amps rating, 25 KA rupturing capacity with adjustable Thermal Magnetic trip release, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

MCB SP 6 to 32 Amp 10 KA, 'B' curve, complete all as specified and as directed.

MCB SPN 6 to 32 Amp 10 KA, 'B' curve, complete all as specified and as directed.

Sub main wiring with Four single core PVC insulated multistrandred un-sheathed FRLS cable of size 10.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with Two runs of continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 10.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Six Runs of 10.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Sub main wiring with two single core PVC insulated multistrandred un-sheathed FRLS cable of size 4.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 4.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Three runs of 4.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for foundation, etc., and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Removing excavated soils to a distance exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 Sqmm 3.5 core including taking down/up unserviceable cable and making good disturbed surfaces, complete all as specified and directed.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note : Punned thickness of sand will be measured and paid.

Brick well burnt locally available sub-class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified and as directed.

Steel pipe galvanised light grade, 100 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers complete all as specified and directed.

Street Light Fitting LED type 35 Watt or higher side, outdoor type, with pressure die casted aluminium housing IP 66 and IK 07 protection including surge protection 5 kA, LED Driver and housing as per BIS standards including connecting terminals, mounting clamp, mounting bracket of suitable size and connecting electrically using 3 core 1.5 sqmm flexible cable in and including metallic conduit from light fitting upto Junction box and all other accessories as required for fixing and making fitting operational on tubular pole complete as directed.

Pole mounting bracket made out of medium grade GI pipe of 32mm dia, bent to 600 required shape of length 1.5 mtr with two No's of flat iron clamps made out of 32 x 6mm with 12mm dia bolts, nuts & washers duly painted with aluminium paint over a coat of primer all as specified and as directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire up to 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

Surya & Gautam Builders

A R ENTERPRISES

KUMAR TRADING CO

Vijay Kumar Contractor and Engineers

JCC ENGINEERS PRIVATE LIMITED

SAMTA CONSTRUCTION CO

M/S SATYA CONSTRUCTIONS

Bidder Name

pardeep singh marwaha

KUMAR TRADING CO

A R ENTERPRISES

SAMTA CONSTRUCTION CO

Vijay Kumar Contractor and Engineers

M/S SATYA CONSTRUCTIONS

Surya & Gautam Builders

JCC ENGINEERS PRIVATE LIMITED