CGI sheet and repair/renovation of Panchayat Ghar at Gia

Amount

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Earth work in excavation by manual means over areas (Exceeding 30 em and upto 1.5 mtr in depth, 1.5 mtr in width as well as 10 sqm. on plan) including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth to be levelled and neatly dressed in : All kinds of Soil

Random Rubble masonry with hard stone from nallah in foundation and plinth including levelling up with cement concrete 1:6:12 (1 Cement: 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level withcement mortar 1:6 (1 Cement: 6 coarse sand)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing Wood Work in Joist for Roofing Ceiling, Partition etc sawn and fixed in position .budloo I fir wood.

Providing corrugated G. S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G. I limpet washers or with G. I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whereever required.0.63mm thick with zinc coating not less than 27 5gm/m2

15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 4 ( 1 cement : 4 coarse sand)1 : 4 ( 1 cement : 4 coarse sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and in -eluding priming coat with cement primer

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo fir/wood

Providing and fixing of 0.125mm thick planking flooring with T&G complete job.

providing and laying of mud concrete under flooring complete job.

Providing and fixing of 12mm thick board with T&G wall panelling 4” width with including polishing and complete job.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.) Anodised aluminium (anodised transparent or <lyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.50 mm thickness (weight not less than 13 .. 50 kg I sqm)

For shutters of doors, windows & ventilators including providing and fixing hinges I pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) Anodised aluminium (anodised transparent or <lyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Carriage of sand and aggregate average lead upto 40 km by M.T

Carriage of stone average lead upto 10 km by M.T

Carriage of cement & steel average lead upto 70 km by M.T

M/S JIGMET WANGCHUK GOVT CONTRACTOR