REPAIR/MAINT OF STREET LIGHTS, FLOOD LIGHTS, TIMER, LT POLE, PANEL AND OTHER MISC WORKS FOR OTM/MD ACCN, SKP, LBS MARG, USMAN ROAD, SURYA CANTEEN, CCSR AND OTHER CONNECTED AREA WEST OF MG ROAD IN THE AREA OF AGE E/M EXT (ELECT) UNDER GE E/M LUCKNOW

Amount

Dismentling and taking out existing unserviceable street light fittings / flood lights of any type from pole / bldgs incl brackets and electric connections complete all as specified and directed.

Taking down existing unserviciable bollard light/post Top Lantern fitting complete all as specified and directed.

Supply and fixing in replacement of 60 W LED Street light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens with silicon gasket, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant.IP lens for better distribution and toughened glass fixed to housing with screws , street light should have IP 66 protection and impact resistance of IK 07 , Lumen efficiency of LED not less than 110>_ lumen per watt system efficency ,power factor >0.95, THD<10% at Full load CRI> 70% ,Street light should have built in potted DriverTHD, open circuit protection , over voltage protection , surge voltage protection 5KV in built & 10KV SPD , and provided with company LOGO ingraved on housing of the Street light complete including taking down of old UNSV fittings complete all as specified and directed. Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement .

Supply and fixing in replacement of 90 W LED Street light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens with silicon gasket, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant.IP lens for better distribution and toughened glass fixed to housing with screws , street light should have IP 66 protection and impact resistance of IK 07 , Lumen efficiency of LED not less than 110>_ lumen per watt system efficency ,power factor >0.95, THD<10% at Full load CRI> 70% ,Street light should have built in potted Driver THD, open circuit protection , over voltage protection , surge voltage protection 5KV in built & 10KV SPD , and provided with company LOGO ingraved on housing of the Street light complete including taking down of old UNSV fittings complete all as specified and directed. Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement.

Supply and fixing of 45 W LED Street light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant.IP lens for better distribution . street light should have IP 66 protection and impact resistance of IK 07 , Lumen efficiency of LED not less than 100>_ lumen per watt system efficency ,power factor >0.95, THD<10% at Full load CRI> 70% ,Street light should have built in potted IP 66 electronic LED driver with APFC, lower THD, open circuit protection , over voltage protection , surge voltage protection 5KV in built & 10KV SPD , and provided with company LOGO ingraved on housing of the Street light complete including taking down of old UNSV fittings complete all as specified and directed.Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement .

Supply and fixing of 120 W LED flood light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens with silicon gasket, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant.IP lens for better distribution and toughened glass fixed to housing with screws , flood light should have IP 66 protection and impact resistance of IK 07 , Lumen efficiency of LED not less than 110>_ lumen per watt system efficency ,power factor >0.95, THD<10% at Full load CRI> 70% ,Street light should have built in potted IP 66 electronic LED potted driver with open circuit protection , over voltage protection , surge voltage protection 5KV in built & 10KV SPD and provided with company LOGO ingraved on housing of the flood light complete including taking down of old UNSV fittings complete all as specified and directed. Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement

Supply and fixing bollard light 60 cm long 10 - 12 watt LED Bollard light having epoxy powder coated pressure die cast aluminium housing Light optic /Diffuser - High impact polycarbonate/Optic colour temprature 5700K CRi>70,THD<10% PF >.90 surge protection 4KV inbuilt ,Rated voltage and frequency 240 Volt,50 Hz street furniture with touch if aesthetic innovative design with uniformly lit diffuser at the upper portion acts a beacon of path guidance in a landsscape IP 65 environmental complete with foundation work nut,bolt and washer etc complete all as specified and directed.

S&F Post top energy saving 240V,50Hz AC, environmental friendly, aesthetically designed electronic constant current,IK07, having epoxy powder coated pressure die cast aluminium housing Top cover spun Al sheet powder coated,front cover Clear acrylic diffuser with indirect symmetrical light distributio, IP-65 luminaire with high power LED as light source of capacity 40 Watt, 5700K PF >0.9, THD<10% and light efficiency 85>_ ,CRI > 70,Surge protection 5KV complete all as specified and directed.

Supply and fixing in replacement security light Bracket made out of galvanised steel light grade pipe of 40mm dia 1.5 mtr long bend to an angle of 120 degree with 02 Nos clamp made out of 50mm x 5mm flat iron and 06 sets of nuts, bolts and washers painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing in replacement street light junction box of suitable size for three phase cable connection outdoor type, weather proof, factory made out of PVC sheet 1.8mm thick with front side hinged opening having locking arrangement with nuts & bolts & arrangement for incoming and out going cable/wire complete comprising with the followings :- (a) Bus bar with four aluminium strips, 100 Amps capacity insulated with insulators, including colour coding strip, including PVC cable of suitable size from bus bar to MCB (b) MCB SPN 5 to 30 Amps - 01 No (c) Clamps made out of 40mm x 5mm flat iron duly welded with nuts & bolts complete all as specified and directed.

Supply and fixing in replacement street light fitting electronic constant current drivers/PCB/electronic gear suitable for 45 to 90 Watt LED flood light/street light fitting as required at site or as per sample complete all as specified and directed.

Supply and fixing in replacement street light fitting electronic constant current drivers/PCB/electronic gear suitable for 120 to 150 Watt LED flood light/street light fitting as required at site or as per sample complete all as specified and directed.

Supply and fixing in replacement street light fitting electronic constant current drivers/PCB/electronic gear suitable for 200 Watt LED flood light/street light fitting as required at site or as per sample complete all as specified and directed.

M&L in replacement for 15mm dia galvanised iron, light grade, ISI marked, complete with all fittings fixed to pole with fixing arrangement including clamps, nut and bolts of suitable size complete all as specified and directed.

S&F in replacement PVC insulated, PVC sheathed twin flat core 1100 volts grade, 4 sqmm aluminium stranded conductor from OH conductor or from junction box to street/security light complete all as specified and directed.

S&F in replacement 1100 volts grade heavy duty flat twin core cable PVC insulated with stranded aluminium conductor of size 16 sqmm and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension GI wire from pole to pole complete all as specified and directed.

Supply and installed steel tubular swaged pole type 410 SP - 31 (9 mtr long) complete with MS base plate of size 300x300x6mm thick at bottom, welded at the centre with through hole of 14mm dia at a height of 300mm above the coping finial cap and painted with two coats of aluminium paint over a coat of red oxide primer with writing number including excavation upto required depth and PCC type C-2 1:3:6 (using 40mm graded) at bottom and PCC type B-1 1:2:4 (20mm graded) for mass filling and pole coping (60x60x30cm) and rendering of coping with 10mm thick in1:6 cement mortar including taking down of old existing pole complete all as specified and directed.

M & L for PCC 1:4:8 type D2 using stone aggregate of 40mm nominal size in foundation concrete for pole/strut complete all as specified and directed.

M & L for PCC 1:3:6 type C2 using stone aggregate of 40mm nominal size in foundation concrete for stays complete all as specified and directed.

M & L for PCC 1:3:6 type C1 using stone aggregate of 20mm nominal size in foundation concrete for coping of poles complete all as specified and directed.

M&L for earthing complet with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground earth pit not less than 2.25m in deep below ground level with top edge of the plote not less than 1.5m deep below normal ground level connected to and incl 4mm dia galvanised wire as earth lead wire by means of bolts, nuts, checknuts and washers of galvanised iron or steel all as specified in electrical plate No 5 of SSR (1991) part-I incl 15mm bore GI pipe for protection upto 5 mtr length and PCC 1:2:4 type B-1 as in pit excavation and earth work in any type of soil charcoal common salt and 20mm bore galvanised medium grade steel tubing for watering with one end fixed with cast iron fixing and wiremesh and testing on completion, complete all as specified and directed.

S&F LED lamp 10 watt, CDL, B-22 cap, (Pin type), 230V, PF-0.95 (min) incl dismentling taking out unsv CFL, complete all as specified and directed.

S&F GI Pipe light grade 40 mm with all fitting such as clamp nuts bolt washer etc laid in trenches / under road / path /bollard light ,Post top lantern fittings etc including taking down complete all as specified and directed.

All as per item No 23 above but 50 mm

All as per item No 23 above but 80 mm

Supply and fix single automatic street light switch suitable for 3KW load complete with two numbers infrared sensor based NATURE SWITCH for automatic switching of street/security lights with one number two pole power contractor 40 Amps (Type MU40-2P,Cs90119) with coil voltage 220/240 V and incoming MCBs single pole - 01 No, out going MCBs single pole - 01 No of rating 32 Amps & circuit wiring with single core multistranded of size 10 sq mm lighting switch operation should be based on natural light lux level, Required lluminance level for switching ON is < 30 Lux. The sensor (one service and one stand by) should also have part night operation facility for 4,5,6---------11&12 hours. The sensor along with suitable power contractor (S), incoming and out going MCBs should be enclosed in a pole/wall mountable enclouser made of Rust proof, Electric shock proof,termite proof and FR grade confirming to IP66 complete all as specified and directed.

NEXT POWER ENTERPRISES

Unnati Engineers

M/S S.B. Singh and Sons

Saurabh Enterprises

M/S National Electrical and Electronics Services

Electromech Engineers

PARADISE INFRA POWER COMPANY

Ajanta Associates