Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw Motorised

Technical Specification for Supply of Safety materials required for various sub-station coming under Transmission(Operation) Zone, Bagalkote

Sl. No Name of the Materials

1 Digital Multimeter 0 to 720V, Suitable to Measure resistance, Capacitance, Inductance, Diode Verification Provision Display Configuration Dual LCD display with backlight, minimum 6000 to 40,000 counts with analog bar graph.

AC/DC Voltage Range 0 V up to 1000 V (fully covering the required 0 to 720V bandwidth safely).

Resistance Range (R) Multi-range tracking from 0.1 Ω up to 40 MΩ or 60 MΩ.

Capacitance Range (C) Broad evaluation spectrum from 1 pF up to 10 mF (10,000 μF).

Inductance Range (L) Dedicated testing band from 0.1 μH up to 40 H or 100 H.

Diode Test Provision Open-circuit test voltage up to AC/DC 3.0 V to check standard and LED junctions.

Continuity Test Beeper Visual indicator and instant acoustic buzzer response for resistances < 30 Ω.

Measurement Safety Category Complies with CAT III 1000V or CAT IV 600V protection matrices.

Fuse Safety Grid High-energy, ceramic fast-acting fuses (1000V, 10kA minimum interrupt rating).

2 Digital tong tester, Ac Clamp Meter-200mA to 200A,Accuracy rate - 0.01 to 0.1 A Measurement Type True-RMS (TRMS) AC Current tracking for precise non-sinusoidal wave analysis. IS/IEC 61557-13, IS 13875, and IEC 61010-2-032.

Primary Current Ranges Multi-range selector: 200 mA / 2 A / 20 A / 200 A AC (covers requested spans).

Resolution Levels 0.1 mA on lowest setting; 0.01 A up to 20A; 0.1 A on the 200A tier.

Base Accuracy Limit ± 1.0% to ± 1.5% of Reading + 5 digits (supports the requested target rates).

Display Configuration 3½ Digit Backlit LCD with an integrated fast-acting analog bar graph (min 2000 counts).

Tong / Jaw Opening Minimum 28 mm to 33 mm internal diameter to encircle standard industrial conductors.

Frequency Response Band Operating range from 45 Hz up to 400 Hz minimum.

Safety Category Rating Certified to CAT III 600V or CAT IV 300V operational environments.

3 LCR Meter, Display-Backlit LCD,Resistance Range -20Ω to 200MΩ,Capacitance Range-2000pF to 2MF, Inductance Range-200μH to 2000H,Test, Frequency-100Hz /120Hz /1kHz /10kHz/100kHz , Data Hold Display Configuration Primary and secondary dual-parameter Backlit LCD screen (minimum 20,000 to 100,000 counts). IS 13875 (Parts 1 & 2) and IEC 61010-1

Resistance Measurement Modes DC Resistance (DCR) and AC Impedance/Resistance (R/Z) modes.

Resistance Range Capacity Broad multi-range span tracking from 0.001 Ω (1 mΩ) up to 20 MΩ / 100 MΩ.

Inductance Range (L) Multi-range tracking from 0.01 μH up to 2000 H or higher.

Capacitance Range (C) Multi-range tracking from 0.01 pF up to 20 mF (20,000 μF).

Test Frequencies Selectable test frequencies (e.g., 100 Hz, 120 Hz, 1 kHz, 10 kHz, up to 100 kHz).

Secondary Display Metrics Dissipation Factor (D), Quality Factor (Q), Phase Angle (θ), Equivalent Series Resistance (ESR).

Test Fixture Interface 4-Terminal / 5-Wire Kelvin probe configuration to eliminate lead resistance errors.

4 Phase Sequence meter, Measure the Phase sequence (R,Y,B) & Open phase Condition through LED and Buzzer. Display Configuration Primary and secondary dual-parameter Backlit LCD screen (minimum 20,000 to 100,000 counts).

Resistance Measurement Modes DC Resistance (DCR) and AC Impedance/Resistance (R/Z) modes.

Resistance Range Capacity Broad multi-range span tracking from 0.001 Ω (1 mΩ) up to 20 MΩ / 100 MΩ.

Inductance Range (L) Multi-range tracking from 0.01 μH up to 2000 H or higher.

Capacitance Range (C) Multi-range tracking from 0.01 pF up to 20 mF (20,000 μF).

Test Frequencies Selectable test frequencies (e.g., 100 Hz, 120 Hz, 1 kHz, 10 kHz, up to 100 kHz).

Secondary Display Metrics Dissipation Factor (D), Quality Factor (Q), Phase Angle (θ), Equivalent Series Resistance (ESR).

Test Fixture Interface 4-Terminal / 5-Wire Kelvin probe configuration to eliminate lead resistance errors.

5 Multimeter, Backlight display-Yes, Voltage Range (AC)-4.000 V-1000 V, Voltage Range (DC)-4 to 600 V Resistance Range (Ohm)-400.0 Ω-40.00 MΩ Display Configuration 3¾ or 4½ Digit Backlit LCD screen showing clear reading counts in dark enclosures.

Minimum Display Resolution Minimum 4000 to 6000 display counts to cleanly capture the 4.000 V millivolt/volt resolution step.

AC Voltage Measurement Dedicated automatic or manual ranges covering 4.000 V / 40.00V / 400.0V / 1000V AC.

Measurement Circuitry True-RMS (TRMS) conversion mode to prevent skewed readings on distorted waveforms.

AC Voltage Frequency Span Operating frequency band tracking safely between 45 Hz up to 1 kHz minimum.

Safety Overvoltage Category Double-insulated housing certified to CAT III 1000 V or CAT IV 600 V industrial environments.

Enclosure Ingress Shielding Rugged, impact-absorbing outer holster matching IP54 or IP67 dust and water seals.

6 Chain saw (Motorised), extremely robust and long lasting chain saw. Highly suitably for cutting firewood, thinning shrubs and bushes and shaping trees. Engine Type Single-cylinder, 2-stroke, air-cooled petrol engine

Engine Displacement 45 cc to 62 cc (Provides the optimal balance of power and weight)

Rated Power Output 2.2 kW to 3.0 kW (3.0 HP to 4.0 HP)

Maximum Engine Speed 11,000 RPM to 13,500 RPM under load acceleration

Guide Bar Length 18 Inches to 22 Inches (46 cm to 56 cm)

Chain Pitch & Gauge Standard 0.325" or 3/8" pitch; 0.058" gauge full-chisel chain

Crankcase Metallurgy Drop-forged Magnesium alloy (resists extreme RPM thermal stress)

Crankshaft Layout 3-piece forged crankshaft for optimal structural weight balancing

Starting System Recoil starter with spring-assisted Easy-Start/Smart-Start technology

Fuel / Oil Tank Ratios ~550 ml fuel tank / ~310 ml chain oil tank (Automatic, adjustable pump)

Dry Weight Profile Maximum 5.5 kg (Powerhead only, excluding bar and chain)

Karnataka Power Transmission Corporation Limited

ENQUIRY NO. CEE/SEE(O)/Safetymaterials04

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Techno commercial Sheet

NAME OF BIDDER, ADDRESS & GSTIN NO.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

ENQUIRY NO. CEE/SEE(O)/Safetymaterials04

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

SL No. DESCRIPTION Compliance whether 'YES' or 'NO' to be indicated below and deviation if any to be indicated in unambigous terms in schedule-II of the tender

1 Digital Multimeter 0 to 720V, Suitable to Measure resistance, Capacitance, Inductance, Diode Verification Provision

2 Digital tong tester, Ac Clamp Meter-200mA to 200A,Accuracy rate - 0.01 to 0.1 A

3 LCR Meter, Display-Backlit LCD,Resistance Range -20Ω to 200MΩ,Capacitance Range-2000pF to 2MF, Inductance Range-200μH to 2000H,Test, Frequency-100Hz /120Hz /1kHz /10kHz/100kHz , Data Hold

4 Phase Sequence meter, Measure the Phase sequence (R,Y,B) & Open phase Condition through LED and Buzzer.

5 Multimeter, Backlight display-Yes, Voltage Range (AC)-4.000 V-1000 V, Voltage Range (DC)-4 to 600 V Resistance Range (Ohm)-400.0 Ω-40.00 MΩ

6 Chain saw (Motorised), extremely robust and long lasting chain saw. Highly suitably for cutting firewood, thinning shrubs and bushes and shaping trees.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- II TECHNICAL DEVIATION

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

Please fill Only in the Light Blue Couloured Box

Please key in the SlNo., Volume , Section , Clause , Desc as given in Tender Documents and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

To, Chief Engineer(Ele.,) Transmission (Operation) Zone, KPTCL Bagalkote

I have read each of the Clauses mentioned in INVITATION FOR BIDS , INSTRUCTION TO BIDDERS , GENERAL CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS.

The following are the TECHNICAL Deviations and Variations from and exceptions to the Specifications and documents for Tender for Supply of 220kV & 66kV Class Telescopic Earth rods with wires pertaining to 220kV R/s and 66kV S/s,Transmission Circle,Mysuru. Except these deiviations and variations, the material shall be supplied as per specification and documents.

SlNO. VOLUME SECTION CLAUSE NO. STATEMENT OF DEVIATIONS/ VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- III COMMERCIAL DEVIATION

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

Please fill Only in the Light Blue Couloured Box

Please key in the SlNo., Volume , Section , Clause , Desc as given in Booklet and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

To, Chief Engineer(Ele.,) Transmission (Operation) Zone, KPTCL Bagalkote

I have read each of the Clauses mentioned in INVITATION FOR BIDS , INSTRUCTION TO BIDDERS , GENERAL CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents for Supply of Safety Materials required for Operations divisions coming under Transmission(Operation)Zone, KPTCL, Bagalkote Except these deiviations and variations, the material shall be supplied as per specification and documents.

SlNO. VOLUME SECTION CLAUSE NO. STATEMENT OF DEVIATIONS/ VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE- IV QUALIFYING REQUIREMENT DATA

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

SHEET FOR TECHNO-COMMERCIAL OPENING

Please don’t insert your Bid values here or else your bid will not be considered for evaluation. Please fill only in blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

To, The Chief Engineer Electy., Transmission(Operation) Zone, KPTCL, Bagalkote-572 103

Bidders Name and address :

Following (mentioned below) is the list of earlier order for the similar type of equipment, Complete in all respects executed by us,details of which are being furnished by us in the support of qualifying requirements for Supply of Safety Materials required for Operations divisions coming under Transmission(Operation)Zone, KPTCL, Bagalkote

Supplies done over the past 5 years.

Sl. No. Manufacturer Details of similar equipment supplied as per qualifying requirements Qty. Details of the Purchaser P.O Ref and Date of Order Date of Supply Date of commissioning Remarks

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE V Bid Form

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

The Chief Engineer Electy.,

Transmission(Oeration) Zone,

Having examined the Bidding documents including Addenda Nos.

(Insert Number of sheets), the receipt of which is hereby duly acknowledged, we, the

undersigned, offer to supply and delivery

(description of goods and services in conformity with the said bidding documents and as

We undertake if our bid is accepted, to commence delivery within

(number) days and to complete delivery of all the items specified in the contract within

(numbers)days calculated from the date of receipt of your notification of Award

we agree to abide by this bid for a period of 180 days from the date fixed for bid opening under

clauses 16 of the instructions to bidders and it shall remain binding upon us and may be

accepted at any time before the expiration of that period.

until a formal contract is prepared and executed, this bid together with your written

acceptance thereof and you notification of award shall constitute a binding contract .

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE VI -ASSESSEMENT OF FINANCIAL CAPABILITY

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

To, The Chief Engineer Electy., Transmission(Operation) Zone, KPTCL, Bagalkote-572 103

1 Name of the Firm

3 Details of Material to be supplied

4 Quantity tendered

Sl No. Particulars Sl. No. Year

1 Total Turnover (Sales ) for the last Preceding 03 years 1

2 Capital assets for the previous three years

3 Liquid Assets

4 Current Ratio for the last year

5 Current Assets

6 Current Liabilities

7 Documents to be enclosed. 1 Audited Balance sheets for the last Preceding 03 years

2 Banker's /Financial Institutions endorsement for limit of Financial lending.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - VII Commercial terms and conditions.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

Tender for Supply of Safety / T&P materials like Digital Multimeter, Digital tong tester, LCR Meter, Multimeter and Chain saw (Motorised) to Operation Divisions coming under Operation Zone KPTCL Bagalkote conforming to our Specifications, F.O.R.D at Store/site including insurance and transportation and un-loading.

Schedule I :Guaranteed Technical Particulars

To, The Chief Engineer Electy., Transmission(Operation) Zone, KPTCL, Bagalkote-572 103

Sl. No. Particulars as per tender terms and conditions Name of the materilas

Digital Multimeter 0 to 720V, Suitable to Measure resistance, Capacitance, Inductance, Diode Verification Provision Digital tong tester, Ac Clamp Meter-200mA to 200A,Accuracy rate - 0.01 to 0.1 A LCR Meter, Display-Backlit LCD,Resistance Range -20Ω to 200MΩ,Capacitance Range-2000pF to 2MF, Inductance Range-200μH to 2000H,Test, Frequency-100Hz /120Hz /1kHz /10kHz/100kHz , Data Hold Phase Sequence meter, Measure the Phase sequence (R,Y,B) & Open phase Condition through LED and Buzzer. Multimeter, Backlight display-Yes, Voltage Range (AC)-4.000 V-1000 V, Voltage Range (DC)-4 to 600 V Resistance Range (Ohm)-400.0 Ω-40.00 MΩ Chain saw (Motorised), extremely robust and long lasting chain saw. Highly suitably for cutting firewood, thinning shrubs and bushes and shaping trees.

1 Name of the Firm

2 Place of Manufacture:

3 Model No & type of the equipment offered as per clause 11 of ITB.

4 Whether bidder agrees for the complete scope of proposal as per clause 2.0 of ITB

5 Whether the bidder possess a minimum experience of 3 years in designing, manufacturing, supply and testing of the equipment specified in the present enquiry as per clause 7 of IFB.

6 Whether performance certificates issued by Power Utilities/public sector undertaings only and issuing officer shall not be below the rank of Executive Engineer or equivqlent are enclosed or not.(Refer clause No:7 of IFB)

7 Whether Bid Security/EMD Paid (Refer clause No:4 of IFB and 15 of ITB)

8 Whether bid is valid for 180 days from the date of opening of Technical Bids (Excluding the date of opening of Technical Bids)

9 Whether the Equipment confirms to the specification (Refer clause No:28 & 29 of ITB) and Technical Specifications.

10 Whether the bidder is willing to supply the quantity tendered.

11 Whether the 'Prices'quoted is firm.(Refer clause No:13 of ITB)

12 Whether any rebates/discounts offered (Yes/No)

13 Whether the offer is inclusive of all taxes, duties and levies as applicable. (Refer clause No:12 of ITB)

14 Whether the delivery schedule is acceptable.

15 Whether the payment terms are acceptable.(Refer clause No:25 of ITB)

16 Whether guarantee terms are acceptable.(Refer clause No:26 of ITB)

17 Whether the penalty terms for delayed supplies acceptable.(Refer clause No:33 & 34 of ITB)

18 Whether the performance security at 3% of the value of the contract is acceptable.(Refer clause No:19 of ITB)

19 Whether technical literature/leaflets/brochures are uploaded along with technocommercial bids.(Refer clause No:29 of ITB)

Nameof the Company