REPAIR AND CLEANING OF SEWAGE LINES DRAINS AND CONNECTED MISC WORKS AT BAIRD PLACE POLO ROAD PARADE ROAD AND CERTAIN BR REPAIRS AND ALLIED WORKS TO BUILDINGS IN THE AREA OF AGE BR-II UNDER GE EAST DELHI CANTT-10

Amount

Demolition in cement concrete of cement concrete in ground floor and paving not exc. 15 cm thick below or above ground level, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) Concrete of any description and in any position not otherwise specifically provided, complete all as specified and as directed.

Demolition in cement concrete of any description and in any position (reinforced), complete all as specified and as directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and as directed.

Demolition of Stone slab and tiles of any description or thickenss in floors, approans etc., complete all as specified and as directed.

Taking down cement plaster on brick or stone wall etc including racking out joints hacking for key; scrubbing down with water, complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Dismantling of RCC fins, parapets,slab, facia, chajjas etc carefully without disturbing the existing re-inforcement, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and as directed.

Taking down door/window/ventilator frames with shutters not exc 1.50 sqm each (without taking off shutters from frame), complete all as specified and as directed.

Taking down door/window frames with shutters exc 1.50 sqm but not exc 4.00 sqm each (without taking off shutters from frame), complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same or other opening as required at site, complete all as specified and as directed. Note : The rate quoted by the contractor are inclusive of taking down old mild steel hinges carefully without damaging and refixing in the same or other opening as directed. Nothing extra cost will be allowed in this account.

Dismantling existing water tanks capacity exc 250 ltr but not exc 500 ltrs, complete all as specified and as directed.

Taking up or down 15 mm bore GI tubing and connections including removal of store, complete all as specified and as directed.

Taking up or down 20 mm bore GI tubing and connections including removal of store, complete all as specified and as directed.

Dismantling of Cast Iron pipe up to 100 mm bore, complete all as specified and as directed.

Demolition and breaking up AC/PVC/SGSW drain pipes 100 mm dia jointed in cement mortar, complete all as specified and as directed.

Demolition and breaking up SGSW drain pipes 150 mm dia jointed in cement mortar, complete all as specified and as directed.

Demolition and breaking up SGSW drain pipes 200 mm dia jointed in cement morta, complete all as specified and as directed

Excavation in post holes (or similar holes) each not exceeding 0.5 Cum and getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, complete all as specified and as directed.

Excavation in trenches, in any type of soil n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out, complete all as specified and as directed

Returning filling in including spreading leveling, watering, and well, ramming in layer nexc 25 cm in layers, complete all as specified and as directed.

Removing excavated material to a distance exc. 50 m and depositing where directed at a level n. exc 1.50 m above the starting point, complete all as specified and as directed.

PCC 1:3:6 type C - 2 using 40 mm graded crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and as directed.

Cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in coping and haunching etc., and other similar work, complete all as specified and as directed.

Cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) in roof kerbs of mud stops, rounded or chamfered on edges, complete all as specified and as directed.

RCC M-25 (using 20mm graded crushed stone aggregate) as in beams, lintels etc., complete all as specified and as directed.

RCC M-25 (using 20mm graded crushed stone aggregate) as in chajjas etc., complete all as specified and as directed.

Providing reinforced cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in kitchen shelves, Chajjas, etc., complete all as specified and directed. Note : The rate quoted by the contractor is deemed to include the necessary scafoldings, supports etc. Nothing extra will be claimed on this account. The work will be executed upto G+3 Storyes building, complete all as specified and as directed.

Providing, precast cement concrete 1:2:4 type B-1, using 20 mm gradedccrushed stone aggregate as in coping, landing, manhole cover and other covering slabs like septic tanks, soak well etc or other similar work set in cement mortar 1:6 complete all as specified and as directed.

Cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate ) as in surface channels and drains complete all as specified and as directed.

Brick work in cement mortar 1:4 straight or curved on plan exceeding 6.0m mean radius and using old size sub class 'B' bricks, complete all as specified and as directed.

All as per description of Srl item No. 34 here-in-before but except bricks, complete all as specified and as directed.

Brick work in cement mortar 1:6 straight or curved on plan exceeding 6.0m mean radius and using old size sub class 'B' bricks, complete all as specified and as directed.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and as directed.

Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes, cantilevers, shelves including supports, overhangs, etc also splays beteen floors and beams finished rough surfaces of concrete, complete all as specified and as directed.

Form work to chajjas, chullah hoods, similar items including edges, complete all as specified and as directed.

Marble of any shade other than white and black 18- 20 mm thick ( table rubbed and polished ) in steps, Jambs,pillars, Cooking platform, floor and like in cement mortar 1:4 including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with marble laid over 20mm thik screed bed in cement mortar 1:6, bedded, jointed and pointed with grey cement slurry including cutting and polishing, complete all as specified and as directed.

Marble of any shade other than white and black 18- 20 mm thick ( table rubbed and polished ) in steps, Jambs,pillars, and like in cement mortar 10mm in cement mortar (1:4) including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with marble laid o bedded, jointed and pointed with grey cement slurry including cutting and polishing, complete all as specified and as directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps , jambs, pillars, window cills, cooking plateforms,dado/wall and like in 15mm thick cement mortar 1:4 including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

Glazed and gauged skelton door shutter of 2nd class hard wood 35 mm thick rebated and prepared to received glass, gauge etc (without sash bars) edges of forming plain,chamfered or rounded fitted with mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I section 8,clause 8.24(a) etc., complete all as specified and as directed.

Plain framed panelled shutters of 2nd class hard wood 30 mm thick (any number of panels) with lock rails and panels of 9mm thick BWP commercial ply or 12mm veneered parcticle board with commercial veneering on both faces. The size of rails and stile as per IS:1003, complete all as specified and as directed.

Flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete all as specified and as directed.

30mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardantgrade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete all as specified and as directed.

12mm Particle board, medium density, flat pressed,single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work etc., complete all as specified and as directed.

18/19mm thick block boards, grade 2 quality, interior grade, commercial type, fixed to frame as in shutters to cup boards etc including 18/19 x 2mm leeping/ beading all round shutters, complete all as specified and as directed.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and as directed.

5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and as directed.

100mm long butt hinges medium weight cold rolled MS to pressed steel/angle iron frames, complete all as specified and as directed.

150mm long aluminum anodized barrel tower bolt of extruded section, complete all as specified and as directed.

125mm long aluminium handles cast type anodised ISI Marked, complete all as specified and as directed.

250mm long MS sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and as directed.

Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and an average width aparture 1.18 mm and fixed with tinned tack/stainless steel wire stapple with screws to wooden beads to wooden joinery,/steel joinary cost of wooden beads / flat iron beads included in the rate, complete all as specified and as directed.

Stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified and as directed. Note- Welder with welding machine reqd to fix wiremesh in old steel windows.

Aluminium alloy powder coated (50 micron) anodized door frame of section 100mm x 44 mm x 2 mm thick, door shutter of aluminium section of size 85 mm x 44 mm x 2 mm thick, top rail and both styles of size 100 mm x 44 mm x 2 mm thick, lock rail and bottom rail of size 115 mm x 44 mm x 2mm thick incl aluminium anodized snap beading and rubber packing & 5.5 mm thick colour designer glass incl 200 mm long tower bolt-2 Nos, 200 mm long Alm handle -02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock (Make :- Godrej), & double action floor door spring(Sandhu/Samrat) heavy duty suitable for 1 m wide shutter for each leaf, complete all as specified and as directed.

Powder coated three track aluminium (glazed/ gauged) window shutters sliding type incl 5.5mm thick glass or stainless steel wiremesh, without sash bar aluminium saction weighting 0.55 Kg per mtr including necessary joining cleats, glazing clips, rubber packing, anodised aluminium beading, sliding channel,roller screws including fittings, complete all as specified and as directed.

Aluminium anodized grills with 6mm x 5mm aluminium section having square gap of 100mm thk with fixing arrangement, complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Steel ventilators with centre hung shutters including steel handles and steel peg stay complete with glazing bars dovetailed or welded, complete all as specified and as directed.

Repair to existing steel door and window by welding/replacing hinges/handle/sliding bolt/tower bolt/wire mesh or removing the steel door and window shutters from the frame and re-fixing after making serviceable, fixed in repairs, complete all as specified and as directed.

Repair to existing in built steel cup board, door, locks, hinges incl necessary welding, drilling and making the locker, steel cupboards, door complete serviceable all as per existing pattern, complete all as specified and as directed.

Repair to existing steel rolling shutters by repairing/welding/oiling/greasing to anchoring rod,springs,side guide channel etc incl dismantling existing steel rolling shutters of any width and refixing after making serviceable after adjusting springs including two coats of paint complete all as specified and as directed.

MS pipe, tube (Square/rectangular) etc as in rafters, purlins, ladders, etc., complete all as specified and as directed.

Mild steel framed work as in doors (as in chowkats) or gates of angle or other section with gusset plates, rails, braces etc., exclusive of steel sheeting or other covering, hanging or fastening and fixing complete conforming to Gde Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and as directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

TMT bars 10mm dia and over, cut to length, bent to shape required,including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre and Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

4 mm thick Non asbestos fibre cement building fixed or laid/inserted to timber/GI/Aluminium framework with screws, complete all as specified and as directed.

75mm thick PCC 1:4:8 type D-2 (40 mm graded stone agg) as in Sub base for floor complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 (40 mm graded stone agg) as in Sub base for floor complete all as specified and as directed.

Pre polished coloured paver concrete tiles 300mmx300mmx 25mm thick, set jointed with coloured cement and pigment and pointed in neat cement slurry in floors, pavements etc including 20 mm thick cement mortar 1:4, complete all as specified and as directed.

40 mm thick plain cement concrete 1:2:4 type B-1, (using 20mm graded crushed stone aggregate), complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B-1, using 20mm graded crushed stone agregate, as in sub base to floor finishes, complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade of approved colour and design laid over with gray cement and pigment, including 30mm thick bedding layer of sand complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection finished even and fair, complete all as specified and as directed.

Kota stone slab 20-25 mm thick with uniform texture in floor with laid over and including 15 mm thick screed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed.

Kota stone slab with uniform texture of 20-25 mm thick in treader of steps, riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 15mm thick in cement morter 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc., complete all as specified and as directed.

Anti skid ceramic coloured tiles 300mm x 300mm x 6 to 7mm thick (square/ rectangular), in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles,laid over and including cement screed bed 15mm thick in cement mortar (1:4) laying floor finish, complete all as specified and as directed.

Anti skid ceramic coloured tiles 400mm x 400mm x 6 to 7mm thick (square/rectangular), in floor etc set and jointed in neat cement slurry and pointed in coloured/white cement to match the colour of tiles,laid over and including cement screed bed 15mm thick in cement mortar (1:4) laying floor finish, complete all as specified and as directed.

Glazed ceramic coloured tile 450mm x 300mm x 6 to 7mm thick on vertical surfaces of walls such as skirting dado etc and jointed in neat cement slurry and pointed in white cement to match laid over and including 10mm thick backing coat in cement mortar 1:4, complete all as specified and as directed.

Coloured vitrified tile 10mm thick (square/rectangular) polished, area of each tile exceeding 0.16Sqm but not exceeding 0.36Sqm in floors laid over screed bed of 15mm thick in cement mortar (1:4) etc., set and jointed in neat cement slurry and pointed white or coloured cement to match, complete all as specified and as directed.

Coloured vitrified tile 10mm thick (square/rectangular) polished, area of each tile exceeding 0.16 Sqm but not exceeding 0.36 Sqm vertical surfaces of walls such as skirting dado etc and jointed in neat cement slurry and pointed in white cement to match laid over and including 10mm thick backing coat in cement mortar 1:4, complete all as specified and as directed.

Renewing tiles in patches, area not exceeding 5Sqm, including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles, complete all as specified and as directed.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces & finishing the surface even & smooth without using extra cement, complete all as specified and as directed.

Rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces & finishing the surface even & smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick on concrete surfaces in cement mortar 1:4 as in ceilings, complete all as specified and as directed.

Taking down cement plaster / duster bed PCC of Column, chajja, Parapets of roof, facia, drops etc and making good with cement plaster 10mm thick in CM 1:3 with PCC 1:2:4, (average thickness of PCC 40mm) as required, brushing neat cement slurry with 3.0kg of cement per sq. metre including necessary form work and scaffolding upto 4th floor including fixing of wire netting where required to match the existing surfaces complete all as specified.

Three coat of white wash including preparation of new surfaces as on ceiling, complete all as specified and as directed.

Applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of Oil bound distember including a layer of Birla white/J K Whte wall care putty, complete all as specified and as directed.

Preparation of old treated surfaces of walls and applying two coats of white wash, complete all as specified and as directed.

Painting two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces exc 10cm girth including preparation of surfaces, complete all as specified and as directed.

Painting one coat of synthetic enamel paint on old treated steel surfaces exc 10cm girth including preparation of surfaces, complete all as specified and as directed.

Two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of girth exc 10cm, including preparation of surfaces, complete all as specified and as directed.

One coat of synthetic enamel paint on old wooden surfaces of girth exc 10cm, including preparation of surfaces, complete all as specified and as directed.

Hacking out old broken glass (any thickness and size quality or description from wooden frame glazed with putty,metal frame including punching or drilling out old glazing pins/spring clips), complete all as specified and as directed.

4mm thick ordinary sheet glass /(black colour glass outside visible inside unvisible ) and glazing with oil putty complete in squares not exc 0.50Sqm each pane, complete all as specified and as directed.

4mm thick Figured glass, pin head type and glazing with oil putty in squares nexc 0.5Sqm in each pane including fixing upto 8 storyed building window with necessary stair arrangement and safety arrangement to fixing upper glass panes, complete all as specified and as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

500 ltrs capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and as directed.

20mm GI tank nipple suitable for HDPE water tank, complete all as specified and as directed.

Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia, fixed in repairs, complete all as specified and as directed.

CP brass shower rose 240mm x 240mm fancy type with chromium plated arm fixed to 15mm pipe of revolving type, fixed in repairs, complete all as specified and as directed. (Make Jaquar Model No: OHS-CHR-1629) or equivalent in Somany/Cera/Hindware)

CP wall mixture diverted 15mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe etc., fixed in repairs, complete all as specified and as directed. (Make Jaquar Model No: ORP-10118PM or equivalent in Somany/Cera/Hindware)

15mm bore bib taps standard of Chromium plated high pressure screwed for iron pipe and fixed etc. fixed in repairs, complete all as specified and as directed. (Make Jaquar Model No: ORP-10037PM or equivalent in Somany/Cera/Hindware)

15mm bore angle stop valve chromium plated brass with flange, fixed in repairs, complete all as specified and as directed.

125 mm size Brass chromium plated shower rose suitable for 15 mm bore pipe, fixed in repairs, complete all as specified and as directed.

15mm dia Pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shank and fly-nuts screwed for iron pipes, complete all as specified and as directed.

PVC connection 15mm sizes with PTMT nuts of length 450 mm, fixed in repairs, complete all as specified and as directed.

PVC Connection 15mm size with PTMT nuts of length 600mm, fixed in repairs, complete all as specified and directed. (Make : Prayag).

CP brass soap dish fixed to plugs with chromium plated brass screws in position, fixed in repairs, complete all as specified and as directed.

Stainless steel kitchen sink with draining board made of 1mm thick sheet for kitchen with plug washers wate pipe cast iron canti lever bracket ovre all size overall size 915mmx 460mm bowl size 410 mmx 330 mmx 160mm, fixed in repairs, complete all as specified and as directed. Make- Maharaja/Nirali/Prayag.

Stainless steel kitchen plate rack size 750 x 900x250 mm deep made out of 1mm thick sheet including fitting arrangement, fixed in repairs, complete all as specified and as directed. Make- Maharaja/Nirali/Prayag.

Grating doom 100mm dia of PTMT, fixed in repairs, complete all as specified and as directed.

Vitreous china wash basin, white, flat back, size 550mm x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, fixed in repairs, complete all as specified and as directed.

Waste fitting 32mm dia, CP for WHB/Sink with long screwed shunks and nuts, fixed in repairs, complete all as specified and as directed.

PVC waste pipe 32mm dia 80cm long suitable for WHB/Sink, fixed in repairs, complete all as specified and as directed.

Plastic water closet seat, back, closed pattern with flat bottom and cover including mild steel chromium plated or aluminised hinging device, fixed in repairs, complete all as specified and as directed.

Vitreous china water closet Orissa Pan 580mm long pan Ist quality ISI marked with cast iron 'P' or 'S' trap including provn of cement concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surfaces, fixed in repairs, complete all as specified and as directed.

Vitreous chinaware wash down water closet pan pedestal pattern white excluding flushing cistern but including jointing to flushing cistern and flush pipe antisyphonage pipe etc, including necessary 'P'/'S' traps as required, fixed in repairs, complete all as specified and as directed.

10 Ltrs capacity PVC low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket, fixed in repairs, complete all as specified and as directed.

Vitreous china wash basin under counter ovel type size 560mm x 450mm under granite slab with all fitting and fixture, fixed in repairs, complete all as specified and as directed.

15mm bore brass CP basin mixer for mixing hot and cold water fixed as per manufacture's mannual, with long shunk and cup washers, screwed both ends for iron pipes or for unions, fixed in repairs, complete all as specified and as directed. Make :- Cera Cat No F3001461/Somany Cat No 220912/ Hindware-F330014CP or equivalent in Jaquar

Health faucet 15 mm bore with CP pipe set, fixed in repairs, complete all as specified and as directed.

Brass spindle suitable for 15 mm bib cock / stop cock/ concealed stop cock/ angle cock / Full turn or Half turn, fixed in repairs, complete all as specified and as directed.

Wall mixer 3 in 1 chromium plated,( L- bend with long bend) with over head shower provision screwed for iron pipes 15mm bore complete all as specified and as directed. (Make : Jaquar Cat No : - 5273 UPR or equivalent in Somany/Cera/Hindware.

110mm bore PVC single socketed in any length with rubber ring joints, fixed in repairs, complete all as specified and as directed.

75mm bore PVC single socketed in any length with rubber ring joints, fixed in repairs, complete all as specified and as directed.

PVC bend 110mm bore any radius, fixed in repairs, complete all as specified and as directed.

PVC bend 75mm bore any radius, fixed in repairs, complete all as specified and as directed.

Cast iron soil waste and vent spun pipes 100mm dia, in any length, with cement joints, laid in trenches/floors, fixed to walls/floors with CI/MS clamps and conforming to IS-1729, complete all as specified and as directed.

Cast iron soil waste and vent spun pipes 75 mm dia, in any length, with cement joints, laid in trenches/floors, fixed to walls/floors with CI/MS clamps and conforming to IS-1729, complete all as specified and as directed.

CI bend for 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

CI bend for 75mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

100 mm bore cast iron floor trap, nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified and as directed.

75mm bore cast iron floor trap, nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified and as directed.

100mm bore cast iron cowls complete all as specified and as directed.

CI oval access door covers for 100/ 110 mm dia. Cast iron pipes fixed in any position, fixed in repairs, complete all as specified and as directed.

100mm cast iron sanitary connection `S' branch, with branch 370 to 450mm long excusing joint, complete all as specified and as directed.

100mm cast iron sanitary connection `P' branch, with branch 370 to 450mm long excusing joint, complete all as specified and as directed.

Salt glazed stone ware gully traps 150 x 150mm square mouth `P' type, fixed in repairs, complete all as specified and as directed.

Factory made steel fibre reinforced (SFRC) man holes covers with frames incl necessary hold fast/hooks (medium duty) of 560 mm dia or rectangular of equivalent area, complete all as specified and as directed.

Factory made steel fibre reinforced (SFRC) man holes covers without frames incl necessary hold fast/hooks (medium duty) of 560 mm dia or rectangular of equivalent area, complete all as specified and as directed.

CI fittings such as Tee,bend,branch piece,floor trap etc upto 100mm dia (waste water/rain water/soil pipe) where ever required to stop leakage including testing of leakage upto eight storied building, fixed in repairs, complete all as specified and as directed.

PVC/UPVC fittings such as Tee,bend,branch piece,floor trap etc upto 100mm dia (waste water/rain water/soil pipe) where ever required to stop leakage including testing of leakage upto eight storied building, fixed in repairs, complete all as specified and as directed.

Raking out cement/lead joints of CI pipes and filling with lead joints / neat cement plaster to stop leakage of joints, complete all as specified and as directed

Cutting in to existing man holes for connecting new drains for internal dia of pipe 150 mm, making good to pipe and rendering , cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1 : 2 :4 type 'B1' smooth finished and reforming benching as required, complete all as specified and as directed.

Cutting in to existing man holes for connecting new drains for internal dia of pipe 200 mm, making good to pipe and rendering , cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1 : 2 :4 type 'B1' smooth finished and reforming benching as required, complete all as specified and as directed.

SGSW drain pipes 150 mm dia laid in trenches and jointed in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

SGSW drain pipes 200 mm dia laid in trenches and jointed in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

Cement concrete bed (1:4:8) type D-2 using 40mm graded stone aggregate as in bedding to SGSW pipes 150mm dia to drain pipe including forming cradels, complete all as specified and as directed.

Cement concrete bed (1:4:8) type D-2 using 40mm graded stone aggregate as in bedding to SGSW pipes 200mm dia to drain pipe including forming cradels, complete all as specified and as directed.

Dismantling of floor of WC with Indian type Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc complete all as specified and directed. (a) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 2.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Cutting shrubs wild gorwth/trees exc 30cm girth and removing complete vegetation growth from walls,Shaft,Roof, including taking out roots from roof/brick work or concrete surfaces and making good the distrubed surfaces with PCC 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate and disposing the rubbish from the site (MOD land) for a block of multistoried flats, complete all as specified and as directed. ( Note : Rate in this item include cutting tress and shrub in each block any number of time during the currency of contract.).

Demolition of reinforced cement concrete water tank of any thickness of size not exc 2.5x2.5x2.0 m /1.50 dia and 2.0 ht at roof level and making the surface smooth with PCC 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate and plaster and disposing the rubbish from the site (MOD land) for a block of multistoried flats, including necessary form work and safety equipment,complete all as specified and as directed by Engineer-in-charge.

Cleaning and maintenance of rain water pipes, open drains, sewage system including WHB bottle traps, Nahani traps, water closet, soil / wastage pipe running on external walls of bldgs, junction holes of any description, sewage line of any sizes including manholes upto the final drop outlet into the septic tank or external sewage system in running / flowing order without blockage of any description in any situations manually or mechanically by deploying 06 safaiwala daily on all working days including Sunday and holidays being sewage line health hazards work from 0900 hours to 1700 hours. The work is to be carried out Bldg upto 8 storeyed with the help of Zula including all safety precautions as per Govt. Rules complete all as directed. Note - a) Contractor shall provide all necessary mechanical equipments / diesel / electrical pump / motor and tools to operate mannually to ensure heigene sanitation during work. b) Daily attendance shall be maintained in the Attendance Register by the JE concerned and a recovery for absent period shall be made @ Rs 500/- per person per day. All relevent record shall be maintained by the contractor and to be submitted before making any payment duly signed by Engineer-in-Charge & JE concerned. c) The details of 06 Nos of safaiwala to be deployed on different locations/complex are as under :- (i) Baird palace - 02, (ii)Polo Road - 02 and Prade Road Area - 02

Demolition and breaking up drain pipes (SGSW / AC / RCC) of any size by puncturing, cleaning of blockage by roding and making good including changing of drain pipes (SGSW/AC/RCC) for the punctured portion of pipes & sealing the joints with required material for no leakage including necessary earth work excavation in any type of soil and upto any depth, returning filling and removal of surplus soil to a distance not exceeding 50 mtr from the starting point complete all as specified and as directed.

Cleaning of deep sewage lines including desludging by Super Sucker Mechanically operated truck mounted of 25 tonne capacity with 12000 liters tanker and water tanker fitted with high jet pressure machine with 8 working hours per day excluding stand by period and disposal of the sludge out side the MOD land, complete all as specified and as directed. Note :- (a) Per day means 8 working hours in a day excluding stand by period due to any reason. (b) In case contractor fails to attend the complaint and to deploy the machine within 24 hrs at site, a recovery of Rs 2000/- per day shall be made from his payment.

Cleaning of Manholes including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the septic tank including site clearance to a distance of 3 Metre around septic tank complete all as specified and as directed by Engineer-in-Charge for Manhole not exceeding 1.50m deep.

Cleaning of septic tanks including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the septic tank including site clearance to a distance of 3 Metre around septic tank complete all as specified and directed by Engineer-in-Charge for septic tank of 10 users capacity.

Cleaning of septic tanks / Manholes including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the septic tank including site clearance to a distance of 3 Metre around septic tank complete all as specified and as directed by Engineer-in-Charge for septic tank of 25 users capacity.

Cleaning of septic tanks including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the septic tank including site clearance to a distance of 3 Metre around septic tank complete all as specified and as directed by Engineer-in-Charge for septic tank of 50 users capacity.

Dewatering of soak wells, sump wells including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the same including site clearance to a distance of 3 Metre around complete all as specified and as directed.

Note :- (Applicable to Srl Items No. 01 to 170) The necessary steel scaffolding upto 12 storied height wherever required to complete the job shall be provided by the contractor with all safety equipments and the rate for scaffolding & safty equipments shall be deemed to be included in the quotted rates by the contractor and nothing extra shall be paid on this account.

NOTE:- Irrespective of whatever specified elsewhere in tender documents, all the debris/waste materials produced out of above mentioned work shall be removed out of Cantonement land and disposed off at locations notified by the Delhi Cantonment Board for disposal of waste building materials within NCR area, without any extra cost to Department under own arrangement of contractors. The rates quoted by the contractors against the items catered here-in-above in the BOQ are inclusive of said provision.

M/s Durga Traders

imran construction company