Provision of Coach Guidance System at 11 stations (19 PFs) at various Railway stations over Bikaner Division having stoppage of 04 or more trains with reserved coaches Trains. (Stations/PFs = STD-1&2, DING-1, DZB-1&2, KNNK-1&2, STNL-1&2, JTS-1&2, SDRA-1&2, MHU-1&2, BWK-1, SDF-1&2, RJR-2)

Horizontal direction drilling/boring without damage of surface road /track using Auger Machine(HDD machine). The bore shall be upto 200 mm dia & shall be done at the depth of minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank height of the 1 bank of the road. The length of the bore shall be minimum 4 Mtrs long. This include insertion of different dia DWC-HDPE pipe/ GI pipes coupling etc. as per direction of Engineer In charge. Note:- Pipe Supply is not covered under this item. Contactor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Digging of trench 1.2 Mtrs. deep from rail flange/ road level and 0.3 Mtrs to 0.6 Mtrs wide and back filling after placing of DWC/ RCC/GI pipe. (Placing of DWC/RCC/GI pipe covered 2 separately).The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. For track crossing, Drg. No.CSTE/3644 Pg.7 of 11 and for Road Crossing, Drg. No. CSTE/3644 Pg. 5 of 11 are to be followed. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution( Unit is Cubic Meter)

Digging of cable trench 0.3 Mtrs. Deep and 0.3 Mtrs. Wide on Asphalted Platform / Road / Hard rocky area. Refilling with earth leveling of trenches & restoring the original surface of trenches.The sharp edges will be smoothened out in bottom of the chase and will be leveled properly. In hard rocky ground area , cables will be laid normally on layer of shifted earth of 0.05 mtrs thickness previously deposited at bottom of the trench and cables will be covered with layer of sand or shifted earth of 0.1 mtr thickness. In case sharp edges of rocky ground can not be protected from shifted earth then GI/ CI /PVC /DWC/ HDPE pipes will be used, if numbers of cables is small.In case number of cables are large RCC duct will be used. In isolated cases, it can be given smooth surface by using either masonry bricks or cement concrete. A row of bricks shall then be placed length wise on the top and jointed with cement mortar and layer of concrete with cement plaster shall be provided on top of the same. Note: This item in hard rocky area will be operated only where normal depth i.e.l.2 mtr is not possible and it will be decided by site engineer/unit officer incharge of work. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution( Unit is Cubic Meter)

Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes/ Trunking. This also includes laying of cables in track crossings & road crossings. Item includes provision of labels of coloured plastic adhesive tapes or any other identifiable material on 4 each cable to give the cable number at each Gantry Post/hectometer post.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(unit is RM running meter)

Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197/2008 or latest and conforming to RDSO Drg.No.SDO/ RDSO/E&B/001 dtd.19.09.08 . It consist of following: (a) Copper bonded steel electrode of 3.0 m long, 17.2 mm dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. © Copper strip of 150x25x6 mm, to 5 terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate. (minimum 10 meter) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation of Unit Maintenance Free Earth as supplied under item no. 13.3 of Chapter 13 of SOR . It includes ( i ) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3 inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper 6 and outer surface (minimum copper bonding thickness of 250 micrones to made requirement of under writer's laboratories (UL) 467-2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note: The installation of this item shall be carried out by the contractor as per RDSO Specn.No.RDSO/SPN/ 197/2008 or latest and conforming to RDSO Drg.No.S DO/RDSO/E&B/001 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution and testing.

Supply of Professional AC/DC clamp meter 3 ¾ digit , true RMS measurement, For 7 Measurement of DC/AC currents up to 1000A, Voltage up to 600V, resistance up to 40 M and frequency up to 1 MHz with set of leads & carrying case. Model - DCM 39A or equivalent/ higher make Motwane/Stanlay/Fluke/Megger Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Handheld Digital Earth Clamp Tester for clamp on earth/ground resistance 8 measurement up to 1000 ohms. Accuracy 0.1 - 0.99 : 1%, 1 - 49 : 1.5% Also measure current leakage up to 20A. No spines required for measurement Model - DECT-2 or equivalent / higher version make Motwane/Stanlay/Fluke/Megger. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Digital Cable Insulation Tester for measurement of cable insulation resistance with auto range 0-500 V DC. Motwani or from any reputed make. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of UTP CAT-6 cable in a roll of 305 meter and make Siemen/ Systemax / Panduit/ Tyco/ Krone/ AMP. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of 4/2 wire combined Portable Light Weight Emergency control telephones of metal body with 6-pin plug as per IRS-TC-75/99 (Amnd 4) or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of patch chord cable (10 meter long) with FC/PC connectors compatible with SDH equipments as per TEC Specn.No.GR/OFJ-02/01 May 2004 with latest Amendment. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply, installation and complete wiring of Optical fiber cable termination box for 24 fibers complete with base housing, base mountings with fixing arrangement etc & splicing of fibers with low loss of pigtail cables as per detailed specification mentioned in respective tender documents. Two pairs of fibers shall be derived from either side of OFC cable at every OFC cable hut provided at 13 wayside stations through pigtails with FC/PC connectors and remaining fibers on either side will be made through by splicing. At OFC terminal stations/MW repeater stations, all fibers shall be derived from either side and to be terminated in OFC termination box through pig tails and FC/PC connector. The OFC termination box to be supplied as per TEC No. G/FTB 01-02 March- 99 or latest. Splice losses in no case should be more than 0.1 dB. Necessary 0 dB connectors should be provided by contractor in OFC termination box. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Supply of DLP trunk 80X50mm with required all changeable internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing & wiring (Laying) of DLP trunk 80X50mm with required all changeable 15 internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Cable will be supplied by Railway and all other fixing material will be supplied by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of DLP trunk 32X20mm with required all changeable internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing & wiring (Laying) of DLP trunk 32X20mm with required all changeable 17 internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Cable will be supplied by Railway and all other fixing material will be supplied by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of Single Mode Single Fiber Optical Media Driver 20KM 10/100/1000(Giga) RJ-45 with inbuilt power supply 230VAC/-48VDC model Techroutes TD-FMC-20KM or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of Double side Digital Clock suitable for platform area with GPS Synchronization in standalone mode as per Clause 5 of RDSO SPN TC 62/2008, (Rev 3.0) Amnd. 2 or latest with all 19 required accessories. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Installation & commissioning of Double side Digital Clock suitable for platform area with 20 GPS Synchronization in standalone mode as per instruction of site incharge with all required accessories and fixing arrangements to commissioning the item. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

Supply of power cable 3 core 2.5 sq mm multi strand (36/0.3 mm dia) cable as per IS 694:1990 reaffirmed 1995 or latest suitable for railway electrification area shall be of reputed make like Delton, LAPP, Finolex, or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply installation and commissioning of versatile PA horn speaker 30W with 100V LMT Taps 15, 10 and 5W complete with fixture of make Philips/Ahuja/AKG. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

Supply and installation of column speaker 15W with LMT all metal weather resistant, including fixtures and other material required. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of 2 core screened/shielded multistrand PVC insulated wire (24/0.2 mm dia) for speaker load line. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply of good quality class-c surge protector device. The parameters of Class C 25 protection device shall be as per clause no. 5.9 of specification no. RDSO/SPN/TC/98/2011, Rev.0 or latest of make phoenix contact, Wago or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Complete wiring, testing, integration and commissioning of IPIS system as per scope of work. This shall includes all connecting cables, connectors etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

Supply, installation and complete wiring of optical fibre cable termination box for 6 27 fibres complete with base housing, base mountings with fixing arrangement etc. & splicing of fibre with low loss of pigtail cables. Splice losses in no case should be more than 0.1 dB. Necessary 0dB connectors should be provided in OFC termination box. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of single mode single fibre optical media converter supports wavelength 28 division multiplexing (WDM) upto 20 KM, wavelength supported 1310 & 1550 nm, 10/100/1000(Giga) RJ-45, model- DIGISOL DG-MC6123S or similar. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply. Unit

B-Non SOR Items