SPECIAL REPAIR TO BLDG NO P-209 (RECORDS LINES) AT GRC KAMPTEE

S & F factory made prelam solid PVC door frame of size 50 mm x 47 mm made out of 5 mm both side prelam PVC sheet reinforced with mild steel square tube complete as per manufacturer’s specification and drawing and as directed.

S & F factory made solid panel both side prelam PVC door shutter with feathered edge 30mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, Mild steel frame shall be covered with heat moulded prelam coloured PVC ‘C’ channel having a PVC sheet strip of 30mm with steel inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, fixing in the frame at site as per specification, drawing and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc of Fe-410-W(Gde E-250) quality, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F mild steel framed work such as monkey protection cage, grills, door frame, gratings with ends of bars shouldered and / or reveted or forged into spikes, framed guard bars and similar work conformig Fe-290 grade-E-165 complete all as specified.

M&L for Preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window (area n-exc 2.00 sqm) Three track made of extruded profileswith wall thickness of 2.3mm (+ -0.2mm). Windowprofile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm),Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed tothe wall with 8mm x 100mm long fasteners, Hardware[Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.40mm and required accessories.(Note: The unit rate quoted by contractor excludescost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

S & F of 4 mm thick plain sheet glass, ordinary quality and glazing or fixed with aluminium windows complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges medium weight , welded to steel frame or fixed to chowkat complete all as specified and directed.

S&F 75 mm long stainless steel butt hinges medium weight , welded to steel frame or fixed to chowkat complete all as specified and directed.

S&F 150mm long aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F aluminium anodized handle casted type150mm long and fixed complete all as specified and directed.

M&L for for cement concrete (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in cills, copings, bed blocks, benching, kerbs, filling hollow of pressed steel frame and the like including necessary form work complete all as specified and directed.

M&L for preparation of new wooden surfaces or wood based materials of any description not otherwise described over 10cm width or girth apply two coat of synthetic enamel paint over a coad of primer complete all as specified and directed.

Supplying and laying of 16 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl taking up or down 15 mm dia bore of galvanised Iron steel tubing and connections including cleaning for refixing, cutting/chauging in wall/floor complete in all respect as specified and directed.

Supplying and laying of 20 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl taking up or down 20 mm dia bore of galvanised Iron steel tubing and connections including cleaning for refixing, cutting/chauging in wall/floor complete in all respect as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

S&F 3mm thick and 38mm wide glass dividing strips as in floors inserted in position, conform to design complete all as specified and directed.

M & L for two coats of brush bond liquid compound of make fosroc or its equvalent water proofing coating over plastered surfaces of sunken portion (Fosroc chemical Ltd) complete all as per manufacturer instructions and directed by Engr-in-charge.

M&L for PCC type E2 1:5:10 (40 mm graded aggreate) in foundation, filling and mass concrete complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.11Sqm but n. exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 incl 25mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floor finished rough to receive floor/screed incl demolition of cement concrete floor 40mm thick complete all as specified and directed.

Material and labour for RCC 1:2:4 type B-1 nominal mix (using 20mm graded stone aggregate) as in ground floor (for grade slab)cover slab, landings etc using of graded stone aggregate of suitable size (reinforcement will be measured and paid separately) incl demolition of 100mm thick PCC complete all as specified and directed.

ials, debris and rubbish to a distance not exceeding 50m as directed by the Engineer-in-Charge complete all as specified and directed.

M & L for flyash brick work with sub class "B" old size bricks straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M & L for 15 mm thick plaster in CM (1:6) on fair face of brick walls finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick plaster in CM (1:6) on fair face of brick walls finished even and smooth without using extra cement incl taking down cement plaster /Dado of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for 15 mm thick plaster in CM (1:4) on fair face of brick walls finished even and smooth without using extra cement incl taking down cement plaster /Dado of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for 10 mm thick plaster in ceiling of CM (1:4) on brick walls finished even and smooth without using extra cement incl taking down cement plaster from ceiling including scrubbing down with water etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over two coats of white putty even and smooth complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coat of weather proof paint over a coat of primer in any tint complete all as specified and directed.

M&L for preparation of old/new plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of existing treatment, nails etc of walls and applying two coats of oil bound distemper over two coats of white putty even and smooth complete all as specified and directed.

M&L for complete removal of existing treatment on old plastered surface and applying two coat of weather proof paint (Apex) over 1 mm external wall care putty and a coat of primer in any tint complete all as specified and directed .

M&L for RCC 1:2:4 type B1 (using 20mm graded stone agg) as in slab and shelves supported on walls incl demolition of reinforeced cement concrete of any description and in any position all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

M&L for rubber moulded chequered cement concrete tiles of size 30cm X 30cm X 20mm thick with grey cement and pigment set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over 75mm thick PCC 1:4:8 type D2 incl demolition of 100mm thick PCC complete all as specified and directed

Taking out existing unserviceable wooden wardrobe including chowkhat of overall size 1000mm x 1900mm approx from existing position of accn including supply & fixing steel wardrobe including chowkhat of same size at the same position of accn all as directed to ensure proper & smooth functioning of wardrobe to the entire satisfaction of Engr-in-Charge. The overall outer size of chowkhat will be 1000mm X 1900 mm approx, made with 0.5mm thick plain black MS sheets and overall shutter size of wardrobe 945mm X 1845mm (approximate) having 2 shutter, 06 Nos of 75mm long, medium weight, MS butt hinges and one number approved quality chromium plated MS handle & one number MS lock of approved quality CP of Godrej pattern with key in duplicate. Thickness of all MS sheets to be used in wardrobe for any purposes including chowkhat, shutter, bracing and back etc except shelves shall be of 0.5mm thick and 02 numbers shelves of size 1.00 x 0.5m approx made of 1mm MS sheet shall be fixed suitably and properly with rivet / welds for storing clothes etc in wardrobe. 01 No MS approved pattern tie hanger shall be fixed in one shutter. One number MS peg set of three shall be fixed in other shutter of wardrobe. 18mm dia MS conduit pipe chromium plated with suitable & approved quality bracket will be fixed to both gable wall of wardrobe. Suitable pattern MS sheets bracing to shelves and shutters shall be provided to avoid any sagging and other related problem in smooth functioning and proper use of wardrobe. All cement plaster, brick wall, PCC, RCC etc disturbed during dismantling of wardrobe shall be made good in cement motar 1:3 properly as per site condition and technical requirement all as directed by Engr-in-Charge. In the bottom portion of wardrobe (of size 1.0 x 0.60m approx) 7mm thick glazed tile exc 0.06 sqm and not exc 0.11 sqm of approved colour and shade shall be laid over and including screed bed of 15mm thick in CM 1:6 including filling the joint with matching colour of tiles. In the sides (of size 0.58 x 1.88m approx each) and back portion of wardrobe (of size 1.0 x 1.88 m approx) 350x450x7mm thick glazed tile of approved colour and shade shall be fixed over and including backing coat of 10mm thick in CM 1:4 including filling the joint with matching colour of tiles. Inside surface of ceiling of wardrobe (of size 1.00x0.60m approx) shall be finished with two coats of OBD over a coat of birla white wall care putty after making good surface properly. Chowkhat will be fixed with suitable rawl plug with and CP steel screw inside wall etc & adjacent surfaces shall be made good to match with adjacent finishing surfaces properly as required and directed for entire completion of work. All steel surface will be painted with two coats of synthetic enamel paint with approved shade and colour by spray painting over one coat of red oxide primer including preparation of surfaces. All other misc work will also be carried out for entire completion and smooth functioning complete all as specified and directed.

Each job

M&L post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L post construction anti termite treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and direc

M&L post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiselling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance as directed by Engr-in-Charge complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof padding finish surface even and smooth without using extra cement including mixed with water proofing compound @ 3% by wt of cement incl demolition of PCC in any description complete all as specified and directed (Note : Water proofing compound will be measured and paid separately)

M&L for rendering 10 mm thick in cm 1:4 in horizontal / vertical surface of brick or concrete surfaces using water proofing liquid compound and finishing surfaces even & fair without using extra cement. complete all as specified and directed. Note: water proofing liquid will be measured and paid separately complete all as specified and directed.

Material & labour for provision of water proofing treatment by using APP torch on mineral/plain finished membrane over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sq m on clean and dry surface and then providing APP membrane having non woven. polyester film reinforcement with 3 mm thick and weight not less than 3 .00 kg/sq m and finished on top with mineral/slate finished torch on system laid with 100 mm & 150 mm over lap on side & end laps respectably complete all as per manufacturers compound complete all as specified and directed.

S&F in repair 25mm dia stainless steel curtain rod fixed to wall with bracket and fancy knobs complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping benching, bed plates and the similar including, weathering, slightly rounded or chamfered edges and throating complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in surface channels and drains complete all as specified and directed

Taking down point wiring with aluminium conductor cable of light point fan & socket light & power complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fitting, regulator etc, and making good to the disturbed surfaces of walls/ floor etc to match with existing surfaces including white washing/colour washing/ distempering to match with existing wall/floor/ceiling finishes, complete all as specified and directed.

Taking down sheet metal enclosure, DB & MCBs main switch etc and making good distrubed sufaces to match with exisiting surfaces, complete all as specified and directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces, complete all as specified and directed.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch, complete all as specifed and directed. Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for One ceiling/exhaust fan point controlled by oneway switch and regulator, complete all as specified and directed. Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for One 3 pin 5 amp socket outlet point on the same board with other switches, complete all as specified and directed. Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for One 3 pin 5 amps socket out let point on independent board, complete all as specified and directed. Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point, complete all as specified and directed. Note :- Cost of cable provided from sub main

DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Supply and fixing for switch modular type single pole one way 6 amp 1 module 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing for socket modular type single pole one way 6 amp 2 module 2/3 pin 250 volts AC suitable for modular switchboxes, complete all as specified and directed.

Material and labour for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the size 2x4.0 Sqmm with earth wire of 1x4.0 Sqmm, complete all as specified and directed. PVC Conduit Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same Make.

Supply and fixing for socket modular type single pole one way 6/16 amp 2/3 pin 2 module, 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing ceiling rose, surface type, three terminals 5 amps, complete all as specified and directed.

Material and labour for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the size 2 x 6 sqmm with earth wire 1 x 6 sqmm complete all as specified and directed. Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same Make.

Material and labour for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the size 4 x 4 sqmm with earth wire 1 x 4 sqmm complete all as specified and directed. Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same Make.

Material and labour for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the size 4 x 10 sqmm with earth wire 1 x 10 sqmm complete all as specified and directed. Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same Make.

Supply and fixing for switch modular type single pole one way 6/16 amp 3 pin 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing 0-5 step -2 module modular type electronic regulators for ceiling fan 1200/1400 mm sweep, 240 volts, 120 watts single pole complete all as specified and directed.

Supplying and fixing 20 Watt LED Tube light fittings complete with aluminum body including tube rod, driver with not less than 100 lm/watt and I/p rated voltage 240V , 50 Hz , color temperature 6500 K, life cycle 50000 hrs, THD<10%, CRI>80, urge protection upto 2KV connecting with 3 core 1 sqmm copper conductor cable complete all as specified and directed.

Refixing of taken down LED fittings as directed of any type after painting work etc complete as directed.

Supply and fix LED baton fitting 2' length including drivers having energy consumption, 10 W ,not less than 100 lm/watt and I/p rated voltage 240V , 50 Hz , color temperature 6500 K, life cycle 50000 hrs, THD<10%, CRI>80, urge protection upto 2KV complete all as directed by the Engineer-in-Charge.

Supply and fixing LED light fitting 10W bulk head luminaries with lamp holders etc complete with all accessories and including connecting upto with twin core twisted flexible cable suitable size of not less than 100 lm/watt and I/p rated voltage 240V , 50 Hz , color temperature 6500 K, life cycle 50000 hrs, THD<10%, CRI>80, urge protection upto 2KV complete all as specified and directed.

Supply & fix fittings with recessed typet LED down lighters 12 W, round/square as specifiedby EIC including driver with rated voltage 240 V , 50 Hz, complete all as directed by the Engineer-in-Charge.

Supply and fix building security light LED 25 W with Lumen O/P 100 lm/watt with driver with rated voltage 240 V, 50Hz color temperature 6000 K,, THD<10%, CRI>70,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc. complete all as specified and directed.

Supply and Fix sheet metal enclosure for vertical Triple Pole and Neutral (VTPN) suitable for MCCB 100 A , 415 Volts, 50 Hz, with IP 54 protection made out of CRCA sheet complete with all connection complete all as specified and directed.

Supply and fix sheet metal enclosure triple pole & neutral for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 12 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Earthing complete with galvanised steet earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanised earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protec-tion pipe 7.50 metre long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

Supply and fix MCB Triple pole & neutral 415 volt 40 to 100 amps 10 KA, 'C' curve complete all as specified and directed.

Supply and fix MCB Triple pole 415 volt 25 to 63 amps 10 KA, 'C' curve complete all as specified and directed.

Supply and fix MCB single pole & neutral 240 volt 32 amps 10 KA, 'C' curve complete all as specified and directed.

Supply and fix MCB single pole 240 volt 6 to 32 amps 10 KA, 'B' curve complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Material and labour for Painting of ceiling fans/exhaust fans including down rod complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and marking of MES NO with black paint complete all as specified and directed by Engineer-in-charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Copper wound Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Opening up of fan motor of ceiling/Exhaust/ wall/cabin fans cleaning starter rotor, cleaning of all parts greasing oiling of bush and bearing reassembling and testing for smooth functioning complete all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed.

Supply and fix exhaust fan, copper wound steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers, complete all as specified and directed.

Supply and fix exhaust fan, copper wound steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers, complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed.

Supply and laying in trenches or fixing in walls/ poles or drawing through piep XLPE insulated, screened, PVC bedded, galvanised steel strip, electric power cable (heavy duty) with aluminium conductor, 1100 Volts, grade cross sectional area 35 Sqmm 3.5 core. Note:- Excavation and earth work, cable protection shall be measured and paid separately, complete all as specified and directed.

Supply and laying in trenches or fixing in walls/ poles or drawing through piep XLPE insulated, screened, PVC bedded, galvanised steel strip, electric power cable (heavy duty) with aluminium conductor, 1100 Volts, grade cross sectional area 16 Sqmm 4 core including testing after laid and jointed all as specified and as directed. Note:- Excavation and earth work, cable protection shall be measured and paid separ

ately, complete all as specified and directed.

Supply and laying in trenches or fixing in walls/ poles or drawing through piep XLPE insulated, screened, PVC bedded, galvanised steel strip, electric power cable (heavy duty) with aluminium conductor, 1100 Volts, grade cross sectional area 10 Sqmm 4 core including testing after laid and jointed all as specified and as directed. Note:- Excavation and earth work, cable protection shall be measured and paid separately.

Excavation in trenches in any type of soft soil not exceeding 1.5 meter wide and not exceeding 25cm thick each, excavated soil in trenches after the cables have been laid and tested complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the cables have been laid and tested complete all as directed and specified.

M&L for sand cushioning with dry and clean sand over and under the under ground cable in trenches, ducts for cable protection incliding levelling and consodilation complete all as specified and directed.

Removal of surpluys soil to a distance not exc. 50m and deposited where directed at a level not exc. 1.5m abov the starting point all as specified and directed.

Supply and fixing LED flood light 100 watt, cool white, 230V AC outdor type with thermal mangament in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete, including three core copper flexible wire of size 1.50 Sqmm for connection from street light fitting to OH line or junction box, including suitable angle/ bracket for hanging of flood light, including connectors, complete all as specified and directed by E-in-C.

Material and Labour for earthing complete with galvanized earth plate electrode 600x 600x 6mm thick burried directly in ground verically to a depth not less than 2.25m below normal ground level with top edge of the plate ont less than 1.50m below normal ground level, connected to and including GI wire 4.0mm as earth soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers of galvanized iron or steel with connected to test point and testing on completion including 40mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35% common salt to a packed thickness of not less than 32 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI pipe for watering, GI check nut, funnel and wire mesh with and including all necessary excavation& earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50m, PCC 1:3:6 type C-1 as in earht pit, 40mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with and including 8mm dia mild steel TMT bar @ 100 mm c/c bothway with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part-I 2009 and as directed. Notes: (a) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

S&F in trenches Tubes, medium grade' galvanised iron 40mm bore for laying of cable under road or other hard standing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.