REPAIRS TO APPROACH PATH, KERB STONE, DRAINS, HARDSTANDING, BRICK WORK, RETAINING WALL, BOUNDARY WALL, COMPOUND WALL, CHAIN LINK FENCING, BOUNDARY PILLARS AND PPGL SHEETS IN AOR OF AGE B/R LEKHANAGAR UNDER GE NASIK ROAD.

Amount

Demolition of concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) and removing the debris out of MOD land.

M&L for broken stone/boudlers as in Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by engr-in-charge.

M&L for 50mm thick Plain cement concrete 1:4:8 type D-2(using 40mm graded aggregate) as in sub base.

M&L for 75 mm thick Plain cement cement concrete1:4:8 type D-2(using 40mm graded aggregate) as in sub base.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering. Note : Moorum to be brought out of MOD land.quoted rate shall be deemed to inclusive of all site clearance and surface dressing.ramming shall be done using mechanical compactor.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape where ever required as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape where ever required as directed by engr-in-charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and removing the debris out of MOD land.

M&L for Rough Shahabad stone 25 mm to 30 mm thick in flooring/plinth set and jointed in in neat cement slurry and pointed in CM 1:4 complete all as specified and directed over and including 15mm thick screed bed(machine mixing) in cement mortar 1:6 and incl provision of PCC 1:2:4 type B0 as in edging/sides of shahabad stone flooring/ plinth protection wherever required as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for 18 to 20 mm thick Granite(telephonic black) work (Table rubbed and polished) in steps,jambs,pillars,window cills,cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 18 to 20mm thick.over and including different type of shade/colour and rounding rounding edges all as specified and directed.

Dismantling of precast concrete articles and precast concrete block set or built in cement mortar and removing the debris out of MOD land.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete over and including applying two coats of synthetic enamel paint over a coat of primer.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removing the debris out of MOD land. Note:work to be executed at any height and situation.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 including raking joints on both sides of wall.curing as per standard engineering practices. Note:work to be executed at any height and situation.

Taking down completely cement or cement lime plaster, any description on brick or stone walls/ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc.and removing the debris out of MOD land. Note:work to be executed at any height and situation.

M&L for Rendering 10mm thick in cement mortar 1:6 on brickwall/concrete surfaces finished fair and even.

M&L for rendering 15 mm thick in cement mortar 1:4 on brick wall /concrete surfaces finished fair and even. Note : work to be executed at any height and situation.

M&L for applying one coat of exterior emulsion paint over a coat of exterior primer on wall surfaces including preparation of surfaces as per standard engineering practices and all as directed by engr-in-charge. Note : work to be executed at any height and situation.

M&L for two coat of cement based paint on walls including preparation of surfaces as per standard engineering practices. Note : work is to be executed at any height and situation.

M&L for Plain cement concrete 1:2:4 type B-1 (using 20 mm graded aggregate) as in copings and the like including weathering, slightly rounded or chamfered angles and throating, as directed and finnshing the surfaces of concrete.

Demolition of concrete in any description and in any position.

M&L for Plain cement concrete1:4:8 type D-2 (using 40 mm graded aggregate) as in foundations, filling and mass concrete.curing as per standard engineering practices.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling RCC posts or struts any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground and removing the debris out of MOD land.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

M&L for Plain Cement concrete 1:2:4 type B-1(using 40 mm graded aggregate) as in foundations, filling and mass concrete.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165,over and including applying two coats of synthetic enamel paint over a coat of primer.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm and diameter of neck 5 to 10 mm.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire.

Supply only chain link MS galvanised fencing, any size or type.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F 45mm to 50mm thick precast 1:2:4,type B0 (using 12.5 mm graded stone aggregate) panels/planks of approved design as in compound wall ,locking each other as per approved design/pattern in precast RCC post,set in cm as 1:4,(measured solid),including all moulding but excluding frame and including dismantling old unserviceable precast wall and removing debris out of MOD land,complete all as specified and directed. Note: The quoted rate shall be inclusive of cost of reinforcement,formwork.design shall be approved by GE.

M&L for precast RCC 1:2:4,type B-1(20mm graded stone aggregate) as in columns,posts,boundary pillars with grooves to lock RCC planks/panels and set in mortar 1:4 complete all as specified and directed. Note. The quoted rate shall be inclusive of cost of reinforcement, formwork.

Dismantling wrought iron or mild any description such as steel gate, steel frame works, purlins, rafter, railings, balusters and window guard bars and directed by Engr-in-Charge. Note:work is to be executed at any height and situation.

S&F Framed work as in grill, doors or gates of angle or other section with gusset plates, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe Grade 290(Gde E-165) complete all over and including applying two coats of synthetic enamel paint over a coat of red oxide primer. Note:work is to be executed at any height and situation.

S&F 1.60 mm thick Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required over and including applying two coats of synthetic enamel paint over a coat of red oxide primer.

Taking down AC rain water pipes(any size or pattern) including all fittings,head shoes,bends,swan neck etc. Note: work to be executed at any height and situation.

S&F PVC (SWR) pipes110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors/wall as RWP including fixing clamp. Note.Work is to be executed at any height and situation.

Demolition of Concrete(reinforced) of any description and in any position not otherwise specifically provided for and removing debris outside MOD land.

M&L for Precast concrete 1:2:4 type B-1(using 20mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in CM 1:4 complete all as specified and directed.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 84,930.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

PARADISE MILESTONE (BID ID -3123801)

M/S R.K.S. CONSTRUCTION (BID ID -3124339)

SVT ENGINEERS AND CONTRACTOR. (BID ID -3130090)

M/S SAMEER SUBHASH PATANI (BID ID -3124380)

M/S MK Nair (BID ID -3132655)

MAHIMA CONSTRUCTION (BID ID -3120374)

Abhiraj Enterprises (BID ID -3122916)

sunway associates (BID ID -3131951)

Ranmale Developers (BID ID -3130550)

MANOVANDANA CONSTRUCTION (BID ID -3132730)

Bidder Name

MAHIMA CONSTRUCTION

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

J Sams Contructions

M/S MK Nair

sunway associates

M/S R.K.S. CONSTRUCTION

Abhiraj Enterprises

MANOVANDANA CONSTRUCTION

Ranmale Developers

PARADISE MILESTONE