Construction of Multipurpose Hall at Jawahar Navodaya Vidyalaya, Sambalpur, Odisha

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in foundation

trenches or drains (not exceeding 1.5 m in width or

1 10 sqm on plan), including dressing of sides and

ramming of bottoms, lift upto 1.5 m, including

getting out the excavated soil and disposal of surplus

excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

3 2.25 not exceeding 20cm in depth,consolidating each 94.76 CUM 196.00 18572.96

deposited layer by ramming and watering, lead upto

50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors,

4 2.27 including watering, ramming,consolidating and 201.09 CUM 2123.75 427064.89

dressing complete.

Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

5 2.25a lead of 5km also including ramming and watering of 2000.00 CUM 700.50 1401000.00

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

6 Anti termite treatment

Supplying chemical emulsion in sealed containers

including delivery as specified.

8 2.34.1 Chlorpyriphos emulsifiable concentrate of 20% 294.20 Litre 234.75 69063.45

Diluting and injecting chemical emulsion for POST-

9 2.35 CONSTRUCTIONAL anti-termite treatment (excluding

the cost of chemical emulsion) :

Along external wall where the apron is not provided

using chemical emulsion @ 7.5 litres / sqm of the

vertical surface of the substructure to a depth of

300mm including excavation channel along the wall

& rodding etc. complete: With Chlorpyriphos/

Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using

chemical emulsion @ one litre per hole, 300 mm

11 2.35.3 apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement : 2

Coarse sand) to match the existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1%

13 Concrete Work

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level 1:5:10 (1

Cement : 5 coarse sand (zone-III) derived from

natural sources : 10 graded stone aggregate 40 mm

nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse

15 4.10 sand (zone-III) derived from natural sources : 4 61.23 SQM 410.85 25156.35

graded stone aggregate 12.5mm nominal size

derived from natural sources)

Extra for providing and mixing water proofing

16 4.12 material in cement concrete work in doses by weight 16.00 18.15 290.40

of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using

17 4.13 1.7kg per square metre on damp proof course after 61.23 SQM 146.15 8948.76

cleaning the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural

18 4.17 sources) over 75mm thick bed of dry brick ballast 40 127.94 SQM 749.30 95865.44

mm nominal size, well rammed and consolidated and

grouted with fine sand,including necessary

excavation,levelling & dressing & finishing the top

Brick edging in full brick width and half brick depth

including excavation, refilling and disposal of surplus

19 16.7.1 earth lead upto 50 metres. 170.58 RM 194.30 33143.69

With common burnt clay F.P.S. (non modular) bricks

of class designation 7.5

20 Reinforced Cement Concrete

Centering and shuttering including strutting,

propping etc. and removal of form for all heights :

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Foundations, footings, bases of columns, etc. for

Suspended floors, roofs, landings, balconies and

access platform.

24 5.9.5 Lintels, beams, plinth beams, girders, bressumers 1489.50 RM 736.40 1096870.01

25 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts. 776.08 SQM 961.30 746044.74

Edges of slabs and breaks in floors and walls Under

Extra for additional height in centering, shuttering

where ever required with adequate bracing, propping

etc., including cost of de-shuttering and decentering

at all levels, over a height of 3.5 m, for every

additional height of 1 metre or part thereof (Plan

area to be measured).

Suspended floors, roofs, landing, beams and

balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete upto plinth level. Thermo-

Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

29 5.22.A.6 and binding all complete above plinth level. 27860.90 KG 107.85 3004798.07

Thermo-Mechanically Treated bars of grade Fe-500 D

Add for plaster drip course/ groove in plastered

surface or moulding to R.C.C. projections.

Providing and laying in position ready mixed or site

batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and

fine aggregate derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag cement,

recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve

durability and workability without impairing

strength; including pumping of concrete to site of

31 5.33 laying, curing, carriage for all leads; but excluding

the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-

charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be

payable separately. In case the cement content in

design mix is more than 110% of the specified

minimum cement content, the contractor shall have

discretion to either re-design the mix

or bear the cost of extra cement.

32 5.33.1 All works upto plinth level

Concrete of M25 grade with minimum cement

content of 330 kg /cum

Concrete of M30 grade with minimum cement

content of 350 kg /cum

38 5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement

content of 330 kg /cum

Concrete of M30 grade with minimum cement

content of 350 kg /cum

45 Masonry Work

Half brick masonry with common burnt clay F.P.S.

(non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

level.Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos

47 6.15 6mm dia. M.S. bars at every third course of half 171.57 SQM 104.80 17980.54

Brick work with non modular fly ash bricks

conforming to IS:12894, class designation 10

48 6.34.2 average compressive strength in superstructure 313.62 CUM 8752.55 2744974.73

above plinth level up to floor V level in : Cement

mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non

modular) bricks of class

designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Random rubble masonry with hard stone in

foundation and plinth including levelling up with

51 7.1 cement concrete 1:6:12 (1 cement : 6 coarse sand :

12 graded stone aggregate 20 mm nominal size)

upto plinth level with :

52 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 54.70 CUM 7311.25 399925.38

53 Cladding Work

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required

size, approved shade, colour and texture laid over 20

54 mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at all

Providing edge moulding to 18mm thick marble

stone counters, Vanities etc. including machine

57 polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-

Extra for fixing marble /granite stone over and above

corresponding basic item, in facia and drops of width

upto 150 mm with epoxy resin based adhesive

including cleaning etc. complete.

Extra for providing opening of required size & shape

for wash basins/ kitchen sink in kitchen platform,

vanity counters and similar location in

marble/Granite/stone work including necessary holes

for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge,

61 8.31 in skirting, risers of steps and dados, over 12 mm 268.67 SQM 1267.95 340660.13

thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

(Size-300x450 )

Providing and Fixing of Acoustical Wall Panel with

square edges made of fibre glass substrate 25mm

thick, wrapped on the front side with an acoustically

transparent fabric as per the approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal,

Titanium, Flame, Peanut and Shell). The panel shall

be classified for Fire Class A, as per ASTM E-84. The

Acoustical Wall Panel shall be of sizes 600x600mm

(Nominal) or 600x1200mm (Nominal) and shall

achieve an NRC of 0.85 (Average value of Absorption

Co-efficient readings taken at 250 Hz, 500 Hz, 1000

Hz and 2000 Hz) with 50mm airgap as per ASTM

C423 to be fixed to wall on a framework of wooden

battens and using Wall panel Impalers (supplied by

the manufacturer) or by using construction adhesives

(as per the instructions laid down by the

manufacturer). The fibre glass substrate shall have a

recycle content of 85%. Properties of Tile Relevant

Standards Base Material Fibre Glass

Panel Dimensions 600mm x 600/1200mm Panel

Panel Finish Acoustically transparent fabric as per

the approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal,

Titanium, Flame, Peanut and Shell).

Fire Properties Class A ASTM E-84

Noise Reduction Co-efficient 0.85 ASTM C423

(Average value of Absorption Coefficient

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing & fixing of 100% Natural Material-

Magnesite (Hygroscopic & biologically sound binding

agent) bonded woodwool Panel planks of

600Mm*1200Mm *25Mm thickness made out of

wood wool fibre of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with

open & smooth surface texture. A Completly

harmless Envirenment & Human Friendly & also a

disposable or recyclable Material & can last for long

span in building interiors As it has long lifespan &

suitable for Indoor conditions with relative air

humidity of upto 90%. Magnesite protects the wood

cells against ageing & fungal attack. To achive upto

NRC=1.00 it should be a clear gap of 200Mm from

wall slab along with the backing of Mineral of

50kg/m3. Edge Detail : AK 01

Heradesign Woodwool - Acoustical Wall Mounting

System Solutions- Ecologically Sound

Material with high mechanical strength with Crash

test of 90Km/H with Ball Impact Test

DIN18032 & EN13964 with flying colors & A

sustainable material (PEFC & FSC Certified)

along with EPD Certified Acc. to EN ISO 14025 (AUB-

Environmental Product declaration).

64 Wood and PVC Work

Providing and fixing panelling or panelling and

glazing in panelled or

panelled and glazed shutters for doors, windows and

65 9.7 clerestory windows (Area of opening for panel inserts

excluding portion inside grooves or rebates to be

measured). Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

66 9.7.7 Float glass panes

5.0 mm thick glass panes (weight not less than

Providing and fixing Fiber Glass Reinforced plastic

(FRP) Door Frames of cross-section 90 mm x 45 mm

having single rebate of 32 mm x 15 mm to receive

shutter of 30 mm thickness. The laminate shall be

moulded with fire resistant grade unsaturated

68 9.121 polyester resin and chopped mat. Door frame 76.05 RM 570.95 43420.75

laminate shall be 2mm thick and shall be filled with

suitable wooden block in all the three legs. The

frame shall be covered with fiber glass from all sides.

M.S. stay shall be provided at the bottom to steady

30 mm thick Fiberglass Reinforced Plastic (F.R.P.)

flush door shutter in different plain and wood finish

made with fire retardant grade unsaturated polyester

resin, moulded to 3 mm thick FRP laminate all

around, with suitable wooden blocks inside at

required places for fixing of fittings and polyurethane

foam (PUF)/Polystyrene foam to be used as filler

material throughout the hollow panel, casted

monolithically with testing parameters of F.R.P.

laminate conforming to table - 3 of IS: 14856,

complete as per direction

of Engineer-in-charge.

Providing and fixing factory made uPVC white colour

casement/ Casement cum fixed glazed door

comprising of uPVC multi-chambered frame, sash

and mullion (where ever required) extruded profiles

duly reinforced with 1.60 ± 0.2 mm thick galvanized

mild steel section made from roll forming process of

required length (shape & size according to uPVC

profile), uPVC extruded glazing beads of appropriate

dimension, EPDM

gasket, zinc alloy (white powder coated) 3D hinges

and one handle on each side of panels along with

zinc plated mild steel multi point lockinghaving

transmission gear, cylinder with keeps and one side

key, G.I fasteners 100 x 8 mm size for fixing frame

to finished wall and necessary stainless steel screws,

etc. Profile of frame & sash shall be mitred cut and

fusion welded at all corners, mullion (if required)

shall be also fusion welded including drilling of holes

for fixing hardware's and drainage of

water etc. After fixing frame the gap between frame

and adjacent finished wall shall be filled with

weather proof silicon sealent over backer rod of

required size and of approved quality, all complete

as per approved drawing & direction of Engineer-in-

Charge. (Single / double glass panes and silicon

sealent shall be paid separately). Variation in profile

in higher side shall be accepted but no extra

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Casement door with top hung ventilator with 3D and

friction hinges (400 x 19 x 1.9 mm) made of (big

frame 67 x 64 mm, sash 67 x 110 mm & mullion 67

mm all having wall thickness of 2.3 ±. 0.2 mm and

single glazing bead / double glazing bead of

dimension.(Area of door upto 2.50 sqm)

Providing and fixing fire resistant door frame of

section 50 x 60 mm on horizontal side & 35 x 60 mm

on vertical sides having built in rebate made out of

1.6 mm thick GI sheet ( Zinc coating not less than

120gm/m²) suitable for mounting 120 min Fire

Rated Glazed Door Shutters. The frame shall be filled

with Mineral wool Insulation having density min

96Kg/m³ . The frame will have a provision of G.I.

Anchor fastners 14 nos ( 5 each on vertical style & 4

on horizontal style of size M10 x 80 ) suitable for

fixing in the opening along with Factory made

Template for SS Ball Bearing Hinges of Size

100x89x3mm for fixing of fire rated glazed shutter .

The frame shall be finished with a approved fire

resistant primer or Powder coating of not less than

30 micron in desired shade as per the directions of

Engineer - in- charge . (Cost of SS ball bearing

hinges is excluded).

Providing and fixing 60 mm thick glazed fire

resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634-1:1999,

tested and certified as per laboratory approved by

Engineer-in-charge, with suitable mounting on door

frame, consisting of vertical styles, top rail & side rail

60 mm x 60 mm wide and bottom rail of 110 mm x

60mm made out of 1.6mm thick G.I. sheet (zinc

coating not less than120gm/m²) duly filled mineral

wool insulation having density min 96 kg/m³ and

fixing with necessary stainless steel ball bearing

hinges of size100x89x3mm of approved make,

including applying a coat of approved fire resistant

primer or powder coating not less than 30 micron etc

all complete as per direction of Engineer-in-charge

(panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door

shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc

coating not less than 120 gm/m²) of size 20 x 33

mm screwed with M4 x 38 mm SS screws at distance

75 mm from the edges and150 mm c/c , including

applying a coat of approved fire resistant

primer/powder coating of not less than 30 micron on

G.I. beading, & special ceramic tape of 5 x 20 mm

size etc complete in all respect as per NBC 2016, IS

16231 (Part 3):2016 and as per direction of Engineer-

incharge with glass of required thickness having 120

minutes of fire resistance both integrity & radiation

control (EW120) and minimum 20minutes of

insulation (EI20). The manufacturer have to give test

report/certification of fire glass and the glass should

have the stamp showing the value of E, EW & EI. The

glass shall be tested in approved NABL accredited lab

or by any other accreditation body which operates in

accordance with ISO/IEC 17011 and accredits labs as

per ISO/IEC 17025 for testing and calibration scopes

shall be eligible. The maximum glazing size shall not

more than 1100x2200 mm (w x h) or 2.42 sqm.

Note: Rate of hardware items deemed to be include

in above items. All Hardware required as per

75 approved shop drawing should pass European

certificate "CE" of conformity / UL with required fire

Providing and fixing bright /matt finished Stainless

76 9.165.1 Steel handles of approved quality & make with 26.00 NOS 119.20 3099.20

necessary screws etc all complete. (a) 125 mm.

Providing & fixing Stainless steel (grade SS-304 or

higher) sliding door bolt/aldrop of size 250x16mm on

door shutter including all accessories as per direction

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and fixing Stainless steel (grade SS-304 or

78 higher) tower bolt (barrel type) with necessary

screws etc. complete all work as per direction of E/I

Filling the gap in between aluminium frame &

adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of approved

quality as per architectural drawings and direction of

Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Steel work in built up tubular (round, square or

rectangular hollow tubes

etc.) trusses etc., including cutting, hoisting, fixing

in position and

applying a priming coat of approved steel primer,

including welding and

bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Designing, Providing, installing and fixing factory

finished customed

design pregalvanized high tensile steel joists

manufactured from G350 Z275 confirming to IS:277-

84 26.62 1992, minimum coating of galvanizing 275 gm/sqm, 200.00 KG 182.05 36410.00

minimum yield stress 35 MPa & minimum tensile

strength of 380 MPa placed 1.23 metre apart to

support the load of slab etc as per the design &

directions of Engineer-in-Charge.

Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

using structural steel etc. as required. In gratings,

frames, guard bar, ladder, railings, brackets,

gates and similar works

Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top

of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge.

Structural steel work riveted, bolted or welded in

built up sections, trusses and framed work, including

cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc., including

cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer, including

welding and bolted with special shaped washers etc.

89 10.16.2 Hot finished seamless type tubes KG 206.35

Designing, providing, installing and fixing factory

finished custom

designed cold form Light Gauge Steel Framed super

comprising of steel wall panel, trusses, purlins etc

manufactured out of minimum 0.75 mm thick steel

sheet as per design requirements. The steel sheet

shall be galvanized (AZ-150gms Aluminium Zinc

Alloy coated steel having minimum yield strength

300-550 Mpa) conforming to AISI specifications and

IBC 2009 for cold formed steel framing and

construction and also as per IS: 875-1987, ISO 800-

1984 and IS:01-

1975. The wind load shall be as per provisions of IS

875 (part -III).

LGSFS frame shall be designed as per IS: 801 using

available software such as Frame CAD Pro-11.7/

ArchitekV2.5.16/ Revit architecture-2011 or

equivalent. Proper usage

of Connection Accessories like Heavy Duty Tension

Ties, Light Duty

Hold-ons, Twist Straps (to connect truss with wall

frames), Strong Tie,

Tie Rod, H-Brackets, Boxing Sections, L-Shaped

Angles for better

structural stability. The framing section shall be cold

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Chequerred precast cement concrete tiles 22 mm

thick in footpath & courtyard, jointed with neat

cement slurry mixed with pigment to match the

shade of tiles, including rubbing and cleaning etc.

complete, on 20 mm thick bed of cement mortar 1:4

(1 cement: 4 coarse sand). Medium shade

pigment using 50% white cement 50%

Marble stone flooring with 18 mm thick marble

stone, as per sample

of marble approved by Engineer-in-charge, over 20

93 11.23 mm (average) thick base of cement mortar 1:4 (1

cement : 4 coarse sand) laid and jointed with grey

cement slurry, including rubbing and polishing

complete with :

52 mm thick cement concrete flooring with concrete

hardener topping, under layer 40 mm thick cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size) and top layer

12 mm thick cement hardener consisting of mix 1:2

95 11.4 (1 cement hardener mix : 2 graded stone aggregate 731.25 SQM 978.45 715491.56

6 mm nominal size) by volume, hardening compound

mixed @ 2 litre per 50 kg of cement or as per

manufacturer's specifications. This includes cost of

cement slurry, but excluding the cost of nosing of

steps etc. complete.

Cement plaster skirting up to 30 cm height, with

cement mortar 1:3

(1 cement : 3 coarse sand), finished with a floating

coat of neat cement.

Providing and laying rectified Glazed Ceramic floor

tiles of size 300x300

mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in all colours, shades,

except White, Ivory, Grey, Fume Red Brown, laid on

20 mm thick Cement Mortar 1:4 (1 Cement : 4

Coarse sand), jointing with grey cement slurry @ 3.3

kg/ sqm including pointing the joints with white

cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all

99 11.41.2 colours and shades, laid on 20mm thick cement 97.22 SQM 1553.45 151026.41

mortar 1:4 (1 cement : 4 coarse sand), jointing with

grey cement slurry @ 3.3kg/sqm including grouting

the joints with white cement and matching pigments

etc., complete. (a) Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different

(thickness to be specified by the manufacturer) with

absorption less than 0.08% and conforming to

approved brand & manufacturer, in all colours and

on 20 mm thick cement mortar 1:4 (1 cement: 4

jointing with grey cement slurry @3.3 kg/sqm

including grouting

the joints with white cement and matching pigments

tiles must be cut with the zero chipping diamond

Laying of tiles will be done with the notch trowel,

clips of required thickness, leveling system and

rubber mallet for

101 11.41A.1 Double charge vitrified tile polished finish of size

Providing and laying Vitrified tiles in different sizes

(thickness to be specified by manufacturer), with

water absorption less than 0.08 % and onforming to

I.S. 15622, of approved make, in all colours & shade,

in skirting, riser of steps, over 12 mm thick bed of

cement mortar 1:3 (1 cement: 3 coarse sand),

jointing with grey cement slurry @ 3.3kg/sqm

including grouting the joint with white cement &

matching pigments etc. complete. Size of Tile

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and laying flamed finish Granite stone

flooring in required design and patterns, in linear as

well as curvilinear portions of the building all

complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4coarse

104 11.55.1 sand) laid and jointed with cement slurry and 40.39 SQM 3186.70 128710.81

pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing

and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :Flamed finish

granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring

in required design and patterns, in linear as well as

curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of

cement mortar 1:4 (1 cement : 4 coarse sand) laid

105 11.56.1 and jointed with cement slurry and pointing with 65.07 SQM 4481.30 291598.19

white cement slurry admixed with pigment of

matching shade including rubbing, curing and

polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black,

Cherry/Ruby Red or equivalent

Providing and laying C.C. pavement of mix M-25 with

ready mixed concrete from batching plant. The ready

mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and

finally finished by floating, brooming with wire brush

etc. complete as per specifications and directions of

106 16.75 Engineer-incharge. 40.17 CUM 9823.80 394622.05

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this item is @

Excess/less cement used as per design mix is

payable/ recoverable separately).

108 FALSE CEILING

Providing and fixing false ceiling at all height

including providing and

fixing of frame work made of special sections, power

M.S. sheets and galvanized with zinc coating of 120

side inclusive) as per IS : 277 and consisting of

angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm

1200 mm centre to centre, one flange fixed to the

ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia

109 bolts, other flange

of cleat fixed to the angle hangers of 25x10x0.50

length with nuts & bolts of required size and other

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running

at the spacing of 1200 mm centre to centre, to which

section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges

of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre,

shall be fixed in a direction perpendicular to G.I.

with connecting clips made out of 2.64 mm dia x 230

wire at every junction, including fixing perimeter

channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30

perimeter of ceiling fixed to wall/partition with the

help of rawl plugs

110 at 450 mm centre, with 25mm long dry wall screws

interval, including fixing of gypsum board to ceiling

perimeter channel with the help of dry wall screws of

mm at 230 mm c/c, including jointing and finishing

to a flush finish

of tapered and square edges of the board with

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

compound , jointing tapes , finishing with jointing

layers covering upto 150 mm on both sides of joint

and two coats of

primer suitable for board, all as per manufacturer's

specification and

also including the cost of making openings for light

fittings, grills,

diffusers, cutouts made with frame of perimeter

channels suitably

fixed, all complete as per drawings, specification and

the Engineer in Charge but excluding the cost of

painting with :

12.5 mm thick tapered edge gypsum plain board

112 12.45.1 conforming to IS: 2095- (Part I) :2011 (Board with 345.62 SQM 1355.80 468597.02

BIS certification marks)

Providing and fixing tiled false ceiling of specified

materials of size

595x595 mm in true horizontal level, suspended on

metal grid of hot dipped galvanized steel sections (

120 grams/ sqm, both side inclusive) consisting of

main "T" runner

with suitably spaced joints to get required length and

mm made from 0.30 mm thick (minimum) sheet,

mm center to center and cross "T" of size 24x25 mm

mm thick (minimum) sheet, 1200 mm long spaced

"T" at 600 mm center to center to form a grid of

1200x600 mm and

secondary cross "T" of length 600 mm and size

24x25 mm made of

0.30 mm thick (minimum) sheet to be interlocked at

1200x600 mm panel to form grids of 600x600 mm

and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of

approved texture

in the grid including, required cutting/making,

opening for services

GI Metal Ceiling Lay in plain Tegular edge Global

white color tiles of size 595x595 mm, and 0.5 mm

thick with 8 mm drop; made of G I sheet having

114 12.52.1 galvanizing of 100 gms/sqm (both sides inclusive) 65.58 SQM 1902.95 124795.46

and electro statically polyester powder coated of

thickness 60 microns

(minimum), including factory painted after bending.

12mm cement plaster in single coat on fair side of

single or half brick wall for exterior plastering up to

floor two level including internal rounded angles

116 13.4.2 chamfers, and/or rounded angles not exceeding 1289.66 SQM 343.65 443191.66

80mm in girth and finished even and smooth no

extra for mixing any additive. 1:6 (1 cement: 6

15 mm cement plaster on the rough side of single or

117 13.5.2 half brick wall of mix : 1:6 (1 cement: 6 coarse 2367.85 SQM 395.35 936129.50

6 mm cement plaster on celling (a) 1:3(1 cement:3

Finishing walls with textured exterior paint of

required shade: New work (Two or more coats

119 13.45.1 applied @ 3.28 ltr/10 sqm) over and including 1289.66 SQM 223.60 288367.98

priming coat of exterior primer applied @ 2.20kg/10

Finishing walls with 100% Premium acrylic emulsion

paint having VOC less than 50 gm/litre and UV

120 13.48A resistance as per IS 15489:2004, Alkali & fungal

resistance, dirt resistance exterior paint of required

shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/

121 13.48A.1 10 sqm. Over and including priming coat of exterior 105.91 SQM 181.25 19196.82

primer applied @ 0.90 litre/10 sqm.

122 13.50 Applying priming coat:

With ready mixed red oxide zink chromate primer of

123 13.50.3 approved brand and manufacture on steel galvanised 905.99 SQM 67.40 61063.73

iron/steel works.

Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade:

125 13.61.1 Two or more coats on new work. 905.99 SQM 155.90 141243.84

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

127 ALUMINIUM WORK

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat

angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately) :

129 21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed

to required shade according to IS: 1868, Minimum

anodic coating of grade

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever

required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid for

Anodised aluminium (anodised transparent or dyed

to required shade according to IS: 1868, Minimum

anodic coating of grade

Providing and fixing glazing in aluminium door,

window, ventilator

shutters and partitions etc. with EPDM rubber /

neoprene gasket

133 21.3 etc. complete as per the architectural drawings and

the directions of

engineer-in-charge . (Cost of aluminium snap

beading shall be paid

in basic item):

With float glass panes of 8 mm thickness (weight not

less than 20 kg/sqm)

135 Water Proofing

Providing and laying in situ seven course water

proofing treatment

with APP (Atactic poly-propylene) modified Polymeric

over roof consisting of first coat of bitumen primer @

sqm, 2nd, 4th & 6th courses of bonding material @

which shall consist of blown type bitumen of grade

85/25 conforming

to IS : 702, 3rd and 5th layers of roofing membrane

Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm

weight consisting

of five layers prefabricated with centre core as 20

film sandwiched on both sides with polymeric mix

and the polymeric

mix is protected on both side with 20 micron

HMHDPE film. 7th, the

top most layer shall be finished with brick tiles of

class designation

10 grouted with cement mortar 1:3 (1cement : 3

fine sand) mixed

with 2% integral water proofing compound by weight

a 12 mm layer of cement mortar 1:3 (1 cement : 3

Providing and laying brick tiles over mumty roofs,

grouted with cement

mortar 1:3 (1 cement : 3 fine sand) mixed with 2%

of integral water

proofing compound by weight of cement, over 12

mm layer of cement

mortar 1:3 (1 cement : 3 fine sand) and finished

With common burnt clay F.P.S. (non modular) brick

of class designation 10

139 Roof Sheeting

PROFLEX Roof System wuth 1.3 mm thick color

coated galvanised sheet

141 Loft and Wardrobes

142 All works above plinth level upto floor V level

Suspended floors, roofs, landings, balconies and

access platform.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

145 5.22.A.6 and binding all complete above plinth level. 63.00 Kg 107.85 6794.55

Thermo-Mechanically Treated bars of grade Fe-500 D

12mm cement plaster in single coat on fair side of

single or half brick wall for exterior plastering up to

floor two level including internal rounded angles

146 13.4.2 chamfers, and/or rounded angles not exceeding 9.45 Sqm 343.65 3247.49

80mm in girth and finished even and smooth no

extra for mixing any additive. 1:6 (1 cement: 6

6 mm cement plaster on celling (a) 1:3 (1 cement:3

Wall painting with acrylic emulsion paint of approved

brand and manufacture to give an even shade :

149 13.60.1 Two or more coats on new work. 17.85 Sqm

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

Providing wood work in frames of false ceiling,

151 9.3 partitions etc. sawn and fixed in position with

necessary stainless steel screws etc.

152 9.3.2 Kiln seasoned and chemically treated hollock wood 0.18 Cum 71337.85 13046.27

Providing and fixing cup board shutters 25 mm thick,

with Pre-laminated flat pressed three layer particle

board or graded wood particle board IS: 12823

marked, exterior grade (Grade l Type ll), having one

153 9.129 side decorative lamination and other side balancing 36.73 Sqm 2307.35 84742.04

lamination, including IInd class teak wood lipping of

25 mm wide x12 mm thick with necessary screws

and bright finished stainless steel piano hinges,

complete as per direction of the Engineer-in-Charge

Providing and fixing Pre-laminated medium density

fibre board IS: 14587:1998 marked, with one side

decorative lamination other side balancing

154 9.157 lamination Grade-I (exterior grade) in shelves with

screws and fittings wherever required, edges to be

sealed with PVC edge bending tape 2.00 mm thick of

approved brand (fittings to be paid separately).

Pre-laminated with decorative lamination one side

155 9.157.1 and other side balancing lamination exterior Grade - 30.71 Sqm 1415.70 43481.81

I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing magnetic catcher of approved

156 9.114 quality in cupboard / ward robe shutters, including

fixing with necessary screws etc. complete.

157 9.114.2 Double strip (horizontal type) 26.00 Each 39.70 1032.20

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills, facias and similar locations of required

size, approved shade, colour and texture laid over 20

158 8.2 mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at all

159 8.2.2 Granite of any colour and shade

Providing & Fixing decorative high pressure

laminated sheet of plain / wood grain in gloss /

matt/ suede finish with high density protective

surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including

cost of adhesive of approved quality 1 mm thick

Providing and fixing wooden moulded beading to

162 door and window frames with iron screws, plugs and

priming coat on unexposed surface etc. complete :

Kiln seasoned and chemically treated hollock wood

Providing and fixing special quality chromium plated

brass cupboard locks with six levers of approved

quality including necessary screws etc. complete.

Providing and fixing chromium plated brass handles

with necessary screws etc. complete: 100mm

Badminton court line marking by acrylic paint of

approved make and as per direction of Engineer-

Incharge (tentative area of hall 625 Sqm for 2

badmintan court)

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

SUB TOTAL CIVIL WORK 30463579.42 2637524.23

Providing and Fixing white viterous china pedestal

type water closet ( European type WC Pan ) with

seat and lid , 10 litre low level White pvc flushing

cistern , including flush pipe with manually

1 DSR -17.2.1 controlled device ( handle lever ) , Conforming to IS 10.00 Each 6515.55 65155.50

: 7231 with all fittings and fixtures complete

including cutting and making good the walls and

floors wherever required . WC Pan with ISI marked

white solid plastic seat and lid .

Providing and fixing wash basin with C.I. brackets,

15 mm C.P. brass pillar taps, 32 mm C.P. brass

2 DSR -17.7 waste of standard pattern, including painting of

fittings and brackets, cutting and making good the

walls wherever require :

White Vitreous China Wash basin size 630x450 mm

with a pair of 15 mm C.P. brass pillar tap

Providing and fixing 600x450 mm beveled edge

mirror of superior glass ( of approved quality )

3 DSR -17.31 complete with 6 mm thick hard board ground fixed to 9.00 Each 1607.95 14471.55

wooden cleats with C.P brass screws and washers

Providing and fixing white vitreous china flat back

half stall urinal of size 580x380x350 mm with white

PVC automatic flushing cistern, with fittings,

standard size C.P. brass flush pipe, spreaders with

17.5 unions and clamps (all in C.P. brass) with waste

fitting as per IS : 2556, C.I. trap with outlet grating

and other couplings in C.P. brass, including painting

of fittings and cutting and making good the walls and

floors wherever required :

Range of three half stall urinals with 10 litre P.V.C.

automatic flushing cistern

Providing and fixing stone slab with table rubbed,

edges rounded and polished, of size 75x50 cm deep

and 1.8 cm thick, fixed in urinal partitions by cutting

a chase of appropriate width with chase cutter and

4 DSR -8.10 embedding the stone in the chase with epoxy grout

or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size)

as per direction of Engineer-in-charge and finished

4.1 8.10.2 Granite Stone of approved shade 3.00 Sqm 4051.85 12155.55

Providing & fixing C.P. brass bib cock of approved

quality conforming to IS :8931.

Providing and fixing CP Brass 32mm size bottle trap

17.22A of approved quality & make and as per the direction 8.00 Each 1034.80 8278.40

of engineer in charge.

Providing and fixing C.P. brass angle valve for basin

6 DSR -18.53 mixer and geyser points of approved quality

conforming to IS:8931

Providing and fixing unplasticised P.V.C. connection

7 DSR -18.21 pipe with PTMT Nuts, collar and bush of approved

quality and colour.

7.1 18.21.2.1 15 mm nominal bore with 45cm length 30.00 Each 97.75 2932.50

Providing and fixing CP Brass extension nipple ( size

8 DSR -18.53A 15mm x 50 mm ) of approved make and quality as 30.00 Each 74.80 2244.00

per direction of engineer - in - charge .

Providing & fixing of Waste pipe for Wash basins &

Sinks including pvc waste fittings complete.

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, ISI : 12701

marked, with cover and suitable locking arrangement

and making necessary holes for inlet, outlet and

overflow pipes but without fittings and the base

support for tank.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and fixing PTMT grating of approved

quality and colour

Providing and fixing 8mm dia C.P./S.S. Jet with

flexible tube upto 1meter long with S.S. Triangular

plate to european type W.C. Of approved quality and

make as approved by engineer in charge.

Providing and fixing vertical or horizontal storage

type hot water heater electrical operated fixed to

wall with anchor bolts & nuts, 15mm CP brass angle

1.00 NS-3 stop cock and 15mm CP brass non-return valve

complete including making connections with 15mm

dia CP connecting pipes on inlet and outlet, suitable

length of power cable and 15 amps plug .

13.1 a) 15 Litre Capacity 6.00 Each 12081.00 72486.00

Providing and fixing CP Brass Single lever telephonic

quality & make as approved by Engineer in charge.

(a) 15 mm nominal dia

17.34 Providing and fixing toilet paper holder :

Providing and fixing PTMT liquid soap container 109

mm wide, 125 mm high and 112 mm distance from

wall of standard shape with bracket of the same

materials with snap fittings of approved quality and

colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with

brackets fixed to wooden cleats with CP brass screws

with concealed fittings arrangement of approved

quality and colour.

450 mm long towel rail with total length of 495 mm,

17.73.1 78 mm wide and effective height of 88 mm, 6.00 Each 673.40 4040.40

weighing not less than 170 gms

Providing and fixing C.P. brass shower rose with 15

Providing and fixing CP brass stop cock (concealed)

18.52 of standard design and approved make confirming to

18.52.1 15mm nominal bore 12.00 Each 670.45 8045.40

Providing & Fixing of Grab bar size 600X600 mm

pipe O.D 32 mm , thiickness 2 mm of non slipping

grip as per standard specification of use in disabled

toilet complete with brackets suitable for wall

installation as per approved sample complete in all

SUB HEAD-II- SOIL , WASTE VENT AND RAIN WATER

Making khurras 45x45 cm with average minimum

thickness of 5 cm cement concrete 1:2:4 (1

cement:2 coarse sand:4 graded stone aggregate of

20 mm nominal size) over P.V.C. sheet 1 mx1

mx400 micron, finished 12 mm cement plaster 1:3

(1 cement:3 coarse sand) and a coat of neat cement

rounding the edges and making and finishing the

outlet complete

Providing and Fixing on wall unplasticised Rigid PVC

Rain water pipes conforming to IS : 13592 Type A ,

including jointing with seal ring conforming to IS :

5382 , leaving 10 mm gap for thermal expansion

2.1 12.41.2 Single Socketed pipes 110 mm diameter 96.00 Metre 377.40 36230.40

Providing and Fixing to the inlet mouth of rain water

3 DSR -12.44 pipe cast iron grating 15 cm diameter and weighing 8.00 Each 54.70 437.60

not less than 440 grams .

Providing and Fixing 100 mm diameter and 60 cm

4 DSR -12.37 long rain water spout in cement mortar 1:4 ( 1

Cement : 4 Fine Sand )

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

4.1 12.37.1 Stone Ware Spout 2.00 Each 164.20 328.40

Providing and Fixing on wall face Rigid Unplasticised

UPVC moulded fittings / accessories for unplasticised

5 DSR -12.42 Rigid PVC Rain water pipes conforming to IS : 13592

Type A including jointing with seal ring conforming to

IS : 5382 leaving 10 mm gap for thermal expansion .

12.42.1 Coupler

12.42.2 Single Push Fit Coupler

12.42.3 Single Tee with door

12.42.4 Single Tee without door

12.42.5 Bend 87.5 degree

12.42.6 Shoe ( Plain )

Providing and Fixing unplasticised PVC pipe clips of

approved design to unplasticised - PVC rain water

pipes by means of 50x50x50 mm hard wood plugs ,

6 DSR -12.43 screwed with MS screws of required length ,

including cutting brick work with fixing in cement

mortar 1:4 ( 1 Cement : 4 Coarse Sand ) and

making good the wall etc . complete

Providing and fixing uPVC 6 Kg/cm2 Soil , Waste &

RWP pipes (IS: 13592 Class B) including all fittings

(plain or door) e.g. bends, junction, cowls, offsets,

access pieces, jointing with rubber ring/solvent

cement joints including cutting chase or holes in

walls and floors and making good wherever required.

Providing & fixing in position upvc P"or S" trap of self

cleaning design of following sizes for the

embedded areas Making proper connection with

chemical sealent joint , cutting chase / hole in floors

/slabs and bringing the same in proper condition in

cement concrete 1:2:4 mix complete as required.

including cost of cutting and making good the walls

and floors where required.

8.1 a) 110 mm inlet and 110 mm outlet 10.00 Each 734.00 7340.00

Providing & fixing in position upvc floor drain

9 NS-6 including cost of cutting and making good the walls

and floors wherever required.

9.1 a) 110 mm inlet and outlet 18.00 Each 451.00 8118.00

Providing and fixing uPVC waste pipes for WB , SINK

, URINAL , FD (IS: 4985 ) 6 Kg / Sqcm including all

fittings (plain or door) e.g. bends, junction, cowls,

10 NS-7 offsets, access pieces, jointing with rubber

ring/solvent cement joints including cutting chase or

holes in walls and floors and making good wherever

Providing and fixing Cast bronze chrome plated

grating with ring and Stainless steel anti cockroach

basket and two SS screw including fixing to the floor

with cement mortar.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and fixing UPVC inlet fitting with

maximum 3 inlets 32,40 or 50 mm size fabricated

from 110 mm dia UPVC pipes and fixed to upvc

sockets,fixed to upvc trap with chemical sealent

joint and set in cement concrete as per standard

drawing complete.

Providing and fixing upvc cleanout plug( Ceiling or

Floor) with suitable insert keys for opening, male

threaded joint with upvc socket fixed to uPVC pipe

complete in all respects.

13.1 a) 110 mm diameter Pipe 4.00 Each 538.00 2152.00

C. SUB HEAD- III - INTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with

1 DSR -18.8 clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement

and the cost of cutting chases and making good the

same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making

good the walls etc.

1.1 18.8.1 15 mm nominal outer dia Pipes 35.00 Metre 497.80 17423.00

1.2 18.8.2 20 mm nominal outer dia Pipes 40.00 Metre 537.60 21504.00

1.3 18.8.3 25 mm nominal outer dia Pipes 40.00 Metre 627.25 25090.00

1.4 18.8.4 32 mm nominal outer dia Pipes 40.00 Metre 739.30 29572.00

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of

Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25mm nominal bore 40.00 Metre 401.55 16062.00

18.7.4 32 mm nominal bore 40.00 Metre 518.75 20750.00

18.7.5 40mm nominal bore 50.00 Metre 702.95 35147.50

18.7.6 50mm nominal bore 120.00 Metre 934.15 112098.00

Providing and fixing Thermoflex or Careflex thermal

insulation tubing, a elastomeric flexible material

having hermetic blister closed cell structure of

expanded synthetic rubber over pipes of following

nominal bores and thickness including all required

accessories complete as per specification.

9 mm thick ( Pipes in Chases)

2.1 a) For 15 mm dia Pipe 10.00 Metre 92.00 920.00

2.2 b) For 20 mm dia Pipe 50.00 Metre 101.00 5050.00

c) For 32 mm dia Pipe 20.00 Metre 120.00 2400.00

Providing and Fixing full way lever operated forged

brass ball valve of brass body with forged brass hard

3 NS-10 chromeplated steel ball tasted to a pressure not less

than 15 kg/sqcm with threaded / flanged joints

complete with nuts, bolts, gaskets, washers etc.

3.1 a) 15 mm dia nominal bore 2.00 Each 250.00 500.00

3.2 b) 20 mm dia nominal bore 5.00 Each 340.00 1700.00

3.3 c) 25 mm dia nominal bore 5.00 Each 512.00 2560.00

3.4 d) 32 mm dia nominal bore 4.00 Each 774.00 3096.00

3.5 e) 40 mm dia nominal bore 3.00 Each 1195.00 3585.00

Providing, fixing, testing and commissioning of

motorised butterfly valve of following dia for filling of

overhead water tank complete with high and low

level control switches to control tanks. The level

controllers shall be installed in overhead tanks. The

4 NS-11 level switch will close the valve when water level is

high in overhead tank and open the valve when

overhead water tank level is low. The system should

be complete in all respects with accessories 220 V

AC / 24 V DC, IP67 electrical water level control unit,

copper control wiring in whether proof casing etc.

4.1 a) 40 mm dia nominal bore 1.00 Each 11393.00 11393.00

ELECTRICAL WORKS

SUBHEAD - I - CIRCUIT CUM POINT WIRING

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

1 DSR 1.10 recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without

Independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in

surface/ recessed PVC conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc as required. (Switch

Control Secondary Points)

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

recessed steel conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required. (Switch Control Primary

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

Independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in

surface/ recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc as required. (Switch

Control Secondary Points)

MCB CONTROL LIGHT POINTS

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 2.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

recessed steel conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 2.5

sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required. (Switch Control Primary

5.1 NSI-1.1 Primary point controlled by one MCB. 12.00 Point 1535.50 18426.00

Same as item above but Secondary point. i.e. Points

5.2 NSI-1.2 to be looped with Primary point with 2.5 sqmm wire 12.00 Point 1365.90 16390.80

and Point wiring

Wiring for light/ power plug with 2X4 sq. mm FRLS

PVC insulated copper conductor single core cable in

6 DSR 1.5 surface/ recessed steel conduit alongwith 1 No. 4 sq. 350.00 Metre 433.00 151550.00

mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth

wire with the following sizes of FRLS PVC insulated

copper conductor, single core cable in surface/

recessed steel conduit as required.

7.1 DSR 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 50.00 Metre 327.00 16350.00

7.3 DSR 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 100.00 Metre 589.00 58900.00

7.4 DSR 1.7.5 2 x 10 sq. mm + 1 x 6 sq.mm earth wire 150.00 Metre 710.00 106500.00

7.6 DSR 1.7.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 60.00 Metre 1645.00 98700.00

Supplying and fixing suitable size GI box with

modular plate and

cover in front on surface or in recess, including

8 DSR 1.31 providing and 16.00 Each 477.00 7632.00

fixing 3 pin 5/6 A modular socket outlet and 5/6 A

switch, connections etc. as required.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supply and Wiring for 250 volts single phase and

neutral 2 Nos 6 amps socket outlate with control by

1 No switched with 2.5 sq.mm PVC insulated copper

conductor 1100 volts grade stranded flexible FRLS

wires in concealed or surface mounted 25 mm dia

2mm thick PVC conduit including providing and

9 NSI-2 fixing of 6 amps 3 pin switch socket outlet of 14.00 Each 1796.31 25148.34

aprpoved make and design in 2 mm thick GI box

with grid plate and earthing of third pin of the

socket with 2.5 Sq. mm PVC insulated copper

conductor stranded flexible FRLS wire.(maximum

four no. of switches socket shall be connected on

Supplying and fixing suitable size GI box with

modular plate and

cover in front on surface or in recess, including

10 DSR 1.32 providing and 15.00 Each 586.00 8790.00

fixing 6 pin 5/6 & 15/16 A modular socket outlet and

modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the

11 DSR-1.33 existing junction box/ wooden block including 2.00 Each 87.00 174.00

connections etc. as required.

Supplying & fixing suitable size GI box wih modular

plate and cover in front on surface or in recess i/c

providing and fixing 25 amp modular socket outlet

and 25 Amps modular SP MCB, “C” curve including

connection, painting etc. as required. (AC's &

Supplying and fixing following modular switch/

13 DSR 1.24 existing modular plate & switch box including

connections but

excluding modular plate etc. as required.

13.1 DSR 1.24.6 Telephone socket outlet 4.00 Nos 148.00 592.00

Supplying and fixing following size/ modules, GI box

14 DSR 1.27 modular base & cover plate for modular switches in

Supplying and fixing following size/ modules, GI box

15 DSR 1.24 modular base & cover plate for modular switches in

15.1 DSR 1.24.4 3 pin , 5/6 amps socket outlet 2.00 Each 122.00 244.00

Supplying and fixing following size/ modules, GI box

16 DSR 1.27 modular base & cover plate for modular switches in

Supplying and fixing of following sizes of medium

conduit along with accessories in surface/recess

17 DSR 1.21 including

cutting the wall and making good the same in case

conduit as required.

Supplying and drawing following pair 0.5 mm dia

FRLS PVC insulated annealed copper conductor,

unarmored telephone cable in the existing surface/

recessed steel/ PVC conduit as required.

SUBHEAD - II - FITTINGS & FIXTURES

Supply, Installation, Testing and Commissioning of 9

W Bulk head Light.

Supply, Installation, Testing and Commissioning of

5W Mirror Light.

Supply, Installation, Testing and Commissioning of

3 NSI-3 18W Recessed/Surface Mounted LED circular 86.00 Each 1975.94 169930.84

Supply, Installation, Testing and Commissioning of

20W Wall/Surface mouted 4 ft. LED

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supply, Installation, Testing and Commissioning of

65W Surface mounted LED Bay light.

Supply, Installation, Testing and Commissioning of

12W Recessed mounted LED circular Downlighter

6 NSI-6 (Cat no-Bajaj Lighting BGSLO SLEEK SURFACE 12W 40.00 Each 1167.60 46704.00

WH RD or equivalent as specified in the approved list

Supply, Installation, Testing and Commissioning of

7 NSI-7 150W highway with 150LPW Ceiling mounted LED 5.00 Each 7469.82 37349.10

Supply, Installation, Testing and Commissioning of

8 NSI-8 250W Highway with 130LPW ceiling mounted LED 15.00 Each 11204.73 168070.95

Supply, Installation, Testing and Commissioning of

BEE 5 star rated, ceiling fan with Brush Less Direct

Motor, class of insulation: B, 3 nos. blades, 30 cm

long down rod, 2

nos. canopies, shackle kit, safety rope, copper

winding, Power Factor not less than 0.9, Service

Value (CM/M/W) minimum 6.00, Air delivery

minimum 210 Cum/Min , 350 RPM (tolerance as per

IS : 374-2019), THD less than 10%, remote or

electronic regulator unit for speed control and all

remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 degree C (max.),

insulation resistance more than 2 mega ohm,

suitable for 230 V, 50 Hz, single phase AC Supply,

earthing etc. complete as required.

Supplying and fixing two module stepped type

regulator on the existing modular plate switch box

connections but excluding modular plate etc. as

Installation, testing and commissioning of ceiling

wiring the down rods of standard length (upto 30

sq. mm FRLS PVC insulated, copper conductor, single

etc. as required.

12 NSI-9 Supply of 300 mm dia Domestic Exhaust Fan 4.00 Each 2155.58 8622.32

13 NSI-10 Supply of heavy duty 450mm Wall Fan 3.00 each 6848.44 20545.32

SUBHEAD - III - MAIN BOARDS

Supplying, installing, testing & commissioning of

following type compartmentalised wall mounted /

floor mounted cubicle board made from 2mm thick

CRCA sheet dust & vermin proof duly phosphatized &

powder coated inclusive of suitable size 4 strip Al.

Busbar complete with interconnection providing

Lugs, inter-earthing, painting etc. i/c providing &

fixing below noted accessories:

Receiving,unloading,storing, handling, installation,

testing and commissioning of following MV

Switchboards complete as required and as per site

condition and dimension of all panels shall be carried

out as per the attachad sld

1 NSI-1 MAIN LT PANEL ( FOR BUILDING ) 1.00 Set 150800.00 150800.00

2 NSI-2 FIRE FIGHTING PANEL 1.00 Set 40000.00 40000.00

SUBHEAD - IV - DISTRIBUTION BOARDS

Supplying and fixing following way, single pole and

sheet steel, MCB distribution board, 240 V, on

surface/ recess,

complete with tinned copper bus bar, neutral bus

bar, din bar, interconnections, powder painted

earthing etc. as required. (But without

MCB/RCCB/Isolator)

1.2 DSR 2.3.2 8 way, Double door 1.00 Each 2573.00 2573.00

1.3 DSR 2.3.3 12 way, Double door 2.00 Each 2315.00 4630.00

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supplying and fixing following way, three pole and

neutral, sheet steel, MCB distribution board, 415

volts, on surface/ recess complete with tinned copper

2 DSR 2.4 busbar, neutral busbar, earth bar, din bar,

detachable gland plate, interconnections,

phosphatized and powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing of following ways surface/

recess mounting, vertical type, 415 V, TPN MCB

distribution board of sheet steel, dust protected, duly

powder painted, inclusive of 200 A tinned copper bus

3 DSR 2.5 bar, common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer) as

required . (Note :Vertical type MCB TPDB is normally

used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V,

10 kA, "C" curve, miniature circuit breaker suitable

4 DSR 2.10 for inductive load of following poles in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole,

240 V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as

Supplying and fixing following rating, four pole, 415

V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as

Supplying and fixing following rating, double pole,

(single phase and neutral), 240 V, residual current

circuit breaker (RCCB), having a sensitivity current

30 mA in the existing MCB DB complete with

connections, testing and commissioning etc.

Supplying and fixing DP sheet steel enclosure on

surface/ recess

along with 25/32 A 240 V "C" curve DP MCB

connections, testing and commissioning etc. as

Supplying and fixing single pole blanking plate in the

9 DSR 2.11 existing 5.00 Each 13.00 65.00

MCB DB complete etc. as required.

FIRE FIGHTING WORKS

A. SUB HEAD - A : PUMPS & EQUIPMENTS

Supplying , Installation , Testing and Commissioning

of Electric Driven Terrace Pump Suitable for

1 18.4 Automatic operation and Consisting of Following

Complete in all Respect as Required ( Terrace Fire

Horizontal Type Multistage , Centrifugal Pump of

1.1 a) Cast Iron Body and Bronze Impeller with Stainless

Steel Shaft Mechanical Seal Conforming to IS : 1520

Suitable HP Squirrel cage Induction motor , TEFC ,

synchronous speed 1500 RPM , Suitable for operation

on 415 Volts 3 Phase 50 Hz AC Supply with IP 68

protection for enclosure Horizontal Foot Mounted

type with class F insulation Conforming to IS : 325

with Energy Efficiency class IE-3

MS Fabricated Common Base Plate Coupling ,

Coupling Guard Foundation bolts etc as Required

Suitable Cement Concrete Foundation duly Plastered

with anti vibration Pads

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

The Head of the Pump is Selected in a manner so as

to give a minimum 3.5 kg/sqcm pressure at the

highest / farthest point

Supplying and Fixing Air Vessel made of 450 mm dia

8 mm thick ms sheet 2000 mm in height with air

release valve on top and flanged connection to riser

2 18.20 drain arrangement with 25 mm dia gunmetal wheel 2.00 Set 18244.00 36488.00

valve with required accessories pressure gauge and

painting with synthetic enamel paint of approved

shade as required

B. PIPING, HYDRANT , AND ACCESSORIES SYSTEM

Providing Laying Testing and Commissioning of C

class Heavy duty MS Pipe Conforming to IS : 1239 /

3589 including Fittings like elbows , tees , flanges ,

tapers , nuts , bolts , gaskets etc in ground including

welding excavation and Providing cement concrete

blocks as supports anticorrosive treatment with

coaltar / asphalts tape as per IS :10221 refilling the

trench etc of following sizes complete as required .

Supplying Fixing Testing and Commissioning of

butterfly valve of PN 1.6 Rating with Bronze

2 18.11 Gunmetal Sheet duly ISI marked complete with nuts

, bolts , washers , gaskets conforming to IS : 13095

of following sizes as required .

Providing Installation Testing and Commissioning of

Non Return Valve of following sizes conforming to IS

: 5312 complete with rubber gasket , GI Bolts , Nuts

, washers etc as required .

Providing Installation Testing and Commissioning of

Stainless Steel Y Strainer fabricated out of 1.6 mm

thick stainless steel , Grade 304 , Sheet with 3 mm

dia holes with stainless steel flange .

Supplying and Fixing Single Headed Internal Hydrant

Valve with instantaneous gunmetal material coupling

5 18.9 of 63 mm dia with cast iron wheel ISI marked

conforming to IS : 5290 ( Type A ) with blank

Gunmetal material cap and chain as required .

5.1 18.9.1 Single Headed Gunmetal Material 3.00 Set 7646.00 22938.00

Supplying and Fixing orifice plate made out of 6 mm

thick stainless steel ( Grade 304 ) with orifice of

required size to be fitted between flange and landing

valve of external and internal hydrants to reduce

pressure at the outlet to the level of 3.5 kg / sqcm

complete as required .

Supplying and Fixing 63 mm dia 15 m Long RRL

Hose pipe with 63 mm dia male and female coupling

duly bound with GI wire , rivet etc . Conforming to IS

: 636 ( Type A ) as Required .

7.1 18.16.1 Gunmetal Material 3.00 Set 5202.00 15606.00

Supplying and Fixing First aid hose reel with MS

Construction Spray painted in Post office red

conforming to IS : 884 complete with the following

20 mm nominal internal dia water hose

thermoplastic ( Textile Reinforced ) Type - 2 as per

20 mm nominal internal dia gunmetal globe valve

Drum and Brackets for fixing the equipments on wall

Connections from Riser with 25 mm dia stop

gunmetal valve and MS Pipe and socket

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supplying and Fixing 63 mm dia Gunmetal Short

Branch Pipe with 20 mm nominal internal diameter

9 18.18 size nozzle conforming to IS : 903 suitable for

instantaneous connection to interconnect hose pipe

coupling as required .

9.1 18.18.1 Gunmetal Material 6.00 Set 2416.00 14496.00

Providing and Fixing of Pressure Switch in MS Pipe

Line including connection etc as required

Providing and fixing of Fire Hose Cabinet size not

less than 2.1 x 1.2 x 0.90 mtr made out of M.S.

sheet not less than 1.5 mm thick having central

opening and 4 mm thick glazed glass doors (Two

nos.) suitably marked on the outside 'with the

11 NS-1 letters "FIRE HOSE" including necessary locking 3.00 Each 30495.00 91485.00

arrangement and painting in PO red colour suitable

to accommodate, internal hydrant valve, 2 nos 15

mtr long Hose pipe, branch pipe, nozzle and fire

man's axe. It shall be fixed inside the FHC Cabinet

Complete as required .

Providing and fixing weather proof Fire Hose Cabinet

of size not less than 0.75 x 0.6 x 0.25 mtr made out

of M.S. sheet not less than 1.5 mm thick having

central opening and 4 mm thick glazed glass doors

(Two nos.) suitably marked on the outside 'with

12 NS-2 the letters "FIRE HOSE" including necessary locking 3.00 Each 11854.00 35562.00

arrangement and painting in PO red colour suitable

to accommodate, external yard hydrant valve, 2 nos

15 mtr long Hose pipe, branch pipe, nozzle and fire

man's axe. It shall be mounted on boundary wall

complete as required.

Providing & fixing Controlled Percolating (CP) Hose

ISI marked (IS:8423) 63 mm dia x 15 m long

complete with instantaneous type Stainless steel 63

mm dia ISI marked Male & Female couplings

(IS:903) bound and riveted to hose pipe with copper

rivets and 1.5 mm copper wire.brusting pressure not

less than 22 Kg/Sqcm. ( Two nos. for each

Providing and fixing standard firemans axe with

heavy rubber handle.

Providing and fixing dial type pressure gauge with

15 NS-5 isolation cock and copper pipe on main header Dial 12.00 Each 3458.00 41496.00

diameter 100 mm celebration 0-16 / sq. cm.

Providing and fixing Fire Extinguishers (CO2 type

powder ) 4 Kg Capacity complete with all

accessories as per manufacturers

specifications.

Providing and fixing Fire Extinguishers (A, B, C type

powder ) 5 Kg Capacity complete with all

accessories as per manufacturers

specifications.

FIRE ALARM CONVENTIONAL SYSTEM

Supplying, installation, testing & commissioning

sector panel suitable for following zones, complete

with visual indications for short circuit fault, open

1 DSR 17.1.9 circuit fault, fire condition and all other standard

facilities as per IS:2189 with mimic diagram for all

area/zone covered, complete with all connections,

interconnections as required

Supplying, installation, testing & commissioning of

conventional beam detector with short circuit isolator

2 NS-1 (inbuilt or seperate) complete with emitter and 2.00 Nos. 43644.00 87288.00

receiver including connections with remote test

features etc complete as

Supplying, installation, testing & commissioning of

3 DSR 17.1.2 smoke detector with builtin LED and mounting base 10.00 Nos. 1153.00 11530.00

complete with all connections etc. as required

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supplying, installation, testing & commissioning of

manual call boxes of MS construction in

4 DSR 17.1.3 surface/recess with stainless steel chain & hammer 4.00 Nos. 474.00 1896.00

assembly complete with glass and push button etc.

Supplying, installation, testing & commissioning fire

alarm sounder with facility to make announcement,

5 DSR 17.1.6 mounted in M.S. box (16 SWG) with hinged cover 4.00 Nos. 557.00 2228.00

plate & suitable for operation with amplifier i/c line

matching transformer etc. complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm

armoured cable, 600/1000V rated with annealed

6 DSR 17.5.2 copper conductor having XLPE insulation, steel wire 160.00 Mtrs 173.00 27680.00

armouring & FRLS outer sheath complete as

Supplying and fixing of following sizes of steel

conduit along with accessories in surface/recess

7 DSR 1.20 including painting in case of surface conduit, or

cutting the wall and making good the same in case

of recessed conduit as required.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supply, Installation, Testing & Commissioning of

Speaker with below Specifications:-

Transducer Size : 15" LF Driver + 1 x 1" Horn-loaded

Compression Driver

Power Handling : 300 Watts Continuous, 1200W

Freq. Range : 75 Hz - 21 kHz

Dispersion : 90 x 40

Sensitivity : 101 dB

Max SPL : 124dB continuous, 130 dB peak

Approved Makes: OHM, British Acoustics, JBL, Bose,

Supply, Installation, Testing & Commissioning of

Subwoofer with below Specifications:-

Transducer Size : 18" Low Frequency Driver

Power Handling : 600 Watts Continuous, 2400W

Dispersion : Omni-directional,

Sensitivity : 101 dB

Max SPL : 129dB continuous, 135 dB peak"

Approved Makes:OHM /British Acoustics/ Bose/

British Acoustics

Supply, Installation, Testing & Commissioning of

Class-D Power Amplifier with below Specifications:-

Number of Channels : 2

Power at 4 Ohms per channel : 1000W

Power at 8 Ohms per channel : 500W

Class-D with LCD Display for critical factors, dual

step power factor correction, built in crossover to set

HPF & LPF Filters

Approved Makes: OHM /British Acoustics/ Bose/

British Acoustics

Supply, Installation, Testing & Commissioning of

Software Controlled Digital DSP with below

Specifications:-

Number of Inputs - 4,

Number of Outputs - 8,

Input Impedance - 12kΩ unbalanced, 24 kΩ

NS balanced 1.00 Nos 80000.00 80000.00

Adjustable Delay - 1 second / input & 1 second /

Approved Makes: OHM /British Acoustics/ Bose/

British Acoustics

3 NS Supply of Flying bar for above speakers 2.00 Nos 20000.00 40000.00

Supply of Stage Monitor Supply of Stage monitor 2-

way, bi-amp. bass reflex design, 400+100W rms ,

75Hz-16KHz freq resp, 12" woofer, 1"HF driver,

130dB SPL max, Disp 90°, polyprop molded

enclosure . Approved Makes: OHM /British Acoustics/

Bose/ British Acoustics

Supply of Audio mixer 24 mono mic inputs 4 line

inputs Freely assignable faders and patching Pre/Post

selection per input per bus AES in and out Global

mode encoders FaderGlow™ GEQ on every bus 20

sub-group / aux busses 4 FX busses 8 Matrix busses

5 NS LR and C Mix busses 4 Stereo Lexicon Effects 1.00 No. 86000.00 86000.00

engines Delay on inputs and outputs 4 Mute Groups

Freely assignable insert loops Harman HiQnet

integration Colour touch screen interface Approved

Makes: (Si Expersion-2)(Allen Heath QU 24)/ (OSL

Supply of Corded microphone (Shure-

SM58/OSL/sennheiser)

Supply of Instrument Microphone(Shure-

57/OSL/sennheiser)

8 NS Supply of Podium Microphone (Shure/OSL/AKG) 2.00 Nos 28411.00 56822.00

9 NS Supply of Microphone Stand Big(GS) 2.00 Nos 1124.00 2248.00

10 NS Supply of Microphone Stand Small(GS) 2.00 Nos 843.00 1686.00

Supply of microphone cable from stage to control

11 NS room for microphone points with conduit pipe etc. 300.00 Mtr 80.00 24000.00

(Belden/Klotz/Netmas)

Supply of Speaker 2.5sqmm x3core

(Belden/Klotz/Netmas)

Supply of microphone connecting box made out

from CRC sheet metal box duly powder coated

13 NS paint,with 6 nos XLR panel mounting socket & phono 4.00 Nos 6322.00 25288.00

socket having the facility to connect the 6nos

microphone channel.

Supply of Professional Head phone(German

Meastro/Sennheiser/OSL)

Supply of Microphone cable XLR to XLR up to 10 Mtr

(Belden/Klotz/Netmas)

Supply of Microphone cable XLR to XLR up to 15 Mtr

(Belden/Klotz/Netmas)

Supply of Speaker connectin connector & MCB Box

for Speaker etc

18 NS Installation charges 1.00 Job. 80000.00 80000.00

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

SUB TOTAL 1219768.00

EXTERNAL DEVELOPMENT WORK

PQC ROAD FOR 3.5 MTR WIDE & 10.0 MTR LONG

Preparation and consolidation of sub grade with

power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm depth,

1 16.1 dressing to camber and consolidating with road roller 55.00 Sqm 218.90 12039.50

including making good the undulations etc. and re-

rolling the sub grade and disposal of surplus

earthwith lead upto 50 metres.

Construction of granular sub-base by providing close

graded Material conforming to specifications, mixing

in a mechanical mix plant at OMC, carriage of mixed

material by tippers to work site, for all leads & lifts,

2 16.78 spreading in uniform layers of specified thickness cum

with motor grader on prepared surface and

compacting with vibratory power roller to achieve the

desired density, complete as per specifications and

directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75

mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base

over a prepared sub-grade with coarse and fine

aggregate conforming to IS:383, the size of coarse

aggregate not exceeding 25 mm, aggregate cement

ratio not to exceed 15:1, aggregate gradation after

blending to be as per specifications, cement content

not to be less than 150 Kg/cum, optimum moisture

content to be determined during trial length

construction, concrete strength not to be less than

10 Mpa at 7 days, mixed in a batching plant,

transported to site, for all leads & lifts, laid with a

mechanical paver, compacting with 8-10 tonne

vibratory roller, finishing and curing etc. complete as

per direction of Engineer in- charge.

Providing and laying C.C. pavement of mix M-25 with

ready mixed concrete from batching plant. The ready

mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and

finally finished by floating, brooming with wire brush

etc. complete as per specifications and directions of

5 16.75 Engineer-incharge. 4.38 cum 9823.80 42979.13

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this item is @

Excess/less cement used as per design mix is

payable/ recoverable separately).

Providing and filling in position rubberized bitumen

hot sealing compound for sealing of expansion joints

in roads / pavements all complete as per direction of

6 16.46.1 Per cmwidth

131.25percm depthper mlength

the Engineer-in-Charge.

Using grade 'A' sealing compound conforming to IS:

Providing and laying at or near ground level factory

made kerb stone of M-25 grade cement concrete in

position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or without

grooves (thickness of joints except at sharp curve

7 16.69 shall not to more than 5mm), including making 0.81 Cum 10117.60 8195.26

drainage opening wherever required complete etc. as

per direction of Engineer-in-charge (length of

finished kerb edging shall be measured for

payment). (Precast C.C. kerb stone shall be

by Engineer-in-charge).

Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

8 2.25a lead of 5km also including ramming and watering of 8.50 cum 700.50 5954.25

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

Painting with synthetic enamel paint of approved

brand and manufacture of required colour to give an

Two or more coats on new work over an under coat

9 13.62.1 of suitable shade with ordinary paint of approved 9.00 sQM 226.25 2036.25

brand and manufacture

FOOTPATH 2.00 MT. WIDE(FOR 10.00 X 2.00 =

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth. 1.5 m in width as well as

10 sqm on plan) including disposal of excavated

earth, lead upto 50m and lift upto 1.5m, disposed

earth to be levelled and neatly dressed.

2.6.1 all kinds of soil 10.63 Cum 177.50 1887.05

Providing and laying in position cement concrete of

2 specified grade excluding the cost of centering and

shuttering. All work upto plinth level.

1:5:10 (1 cement : 5 course bound: 10 graded stone

aggregate 40mm nominal size)

Providing and laying 60mm thick faciory made

cement concrete interlocking paver block of M -30

grade made by block making machine with strong

vibratory compaction, of approved s;ze, design &

shape, laid in required colour and pattern over and

including 50mm thick compacted bed of coarse sand,

filling the joints with line sand etc. all complete as

per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory

made kerb stone of M-25 grade cement concrete in

position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), ncluding making joints with or without

grooves (thickness of joints except at sharp curve

shall not to more than 5mm), including making

drainage opening wherever required complete etc. as

per direction of Engineer-in-charge (length of

finished kerb edging shall be measured for

payment). (Precast C.C. kerb stone shall be

approved by Engineer-in-charge).

Painting with synthetic enamel paint of approved

5 brand and manufacture of required colour to give an

Two or more coats on new work over an under coat

13.62.1 of suitable shade with ordinary paint of approved 16.88 Sqm 226.25 3817.97

brand and manufacture

Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

lead of 5km also including ramming and watering of

the earth in layers not exceeding 20 cm in trenches,

sides of foundation etc. complete.

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of oundations etc. in layers

7 not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

Centering and shuttering including strutting,

propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for

SUB HEAD- V EXTERNAL WATER SUPPLY

Supplying, installing, testing and commissioning

vertical on line multi stage centrifugal pumping set

with mechanical seal, C.I. volute and SS impeller &

SS shaft connected to a TEFC induction motor of

suitable HP for 415 volts, 3 phase, 50 cycles A.C.

supply with 150 mm dia pressure gauge with

SS/gunmetal isolation cock, vibration eliminating

MR pads, base plate wiring upto panel and equipment for

water level controller to start and stop the pump

automatically at predecided levels of the water in the

tank with provision of protection for dry run etc.

complete in all respect (The shop drawing or the

pumps along with its characteristics curves, model

and technical data etc. are to be submitted for

approval before purchase of pump).

Domestic water pumps (Treated water transfer pump

to terrace tank) (1W+1S)

Capacity 50 lpm

Providing and fixing G.I. pipes complete with G.I.

fittings and clamps, i/c cutting and making good the

Internal work - Exposed on wall

18.10.6 50 mm dia nominal bore 21.00 RMT 1048.35 22015.35

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and fixing G.I. pipes complete with G.I.

18.12 fittings including trenching and refilling etc.

SUB HEAD- IV EXTERNAL SEWARAGE LINE

Excavating trenches of required width for pipes,

cables, etc including excavation for sockets,

anddressing of sides, ramming of bottoms, depth up

to 1.5 m, including getting out the excavated soil,

2.1 and then returning the soil as required, in layers not

exceeding 20 cm in depth, including consolidating

each deposited layer by ramming, watering, etc. and

disposing of surplus excavated soil as directed,within

a lead of 50 m :

2.10.1 All kinds of soil

Pipes, cables etc. exceeding 80 mm dia but not

exceeding 300 mm dia

Providing and fixing square-mouth S.W. gully trap

class SP-1 complete with C.I. grating brick masonry

chamber with water tight C.I. cover with frame of

300x300 mm size (inside) the weight of cover to be

19.4.1.1 not less than 4.50 kg and frame to be not less than 7.00 EACH 2707.65 18953.55

2.70 kg as per standard design: 100x100 mm size P

type. With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

Constructing brick masonry manhole in cement

mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C.

top slab with 1:2:4 mix (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size),

foundation concrete 1:4:8 mix (1 cement : 4 coarse

sand : 8 graded stone aggregate 40 mm nominal

19.7 size), inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished with

floating coat of neat cement and making channels in

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size)

finished with a floating coat of neat cement complete

as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455x610 mm internal

dimensions,total weight of cover and frame to be not

less than 38 kg (weight of cover 23 kg and weight of

19.7.1 frame 15 kg) :

With common burnt clay F.P.S.(non modular) bricks

19.7.1.1 of class designation 7.5 8.00 EACH 12770.55 102164.40

Constructing brick masonry road gully chamber

45x45x77.5 cm with bricks in cement mortar 1:4 (1

cement : 4 coarse sand ) with precast R.C.C. vertical

grating complete as per standard design :

with common burnt clay F.P.S.(non module) brick of

class designation 7.5

Providing, laying and jointing glazed stoneware pipes

class SP-1 with stiff mixture of cement mortar in the

proportion of 1:1 (1 cement : 1 fine sand) including

testing of joints etc. complete :

Providing and laying cement concrete 1:5:10 (1

cement : 5 coarse sand : 10 graded stone aggregate

40 mm nominal size) all-round S.W. pipes including

bed concrete as per standard design :

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing orange colour safety foot rest of minimum

6 mm thick plastic encapsulated as per IS : 10910,

on 12 mm dia steel bar conforming to IS: 1786,

having minimum cross section as 23 mmx25 mm

and over all minimum length 263 mm and width as

165 mm with minimum 112 mm space between

protruded legs having 2 mm tread on top surface by

ribbing or chequering besides necessary and

adequate anchoring projections on tail length on 138

19.16 mm as per standard drawing and suitable to with 24.00 EACH 553.70 13288.80

stand the bend test and chemical resistance test as

per specifications and having manufacture's

permanent identification mark to be visible even

after fixing, including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6 (1

cement : 3 coarse sand : 6 graded stone aggregate

20 mm nominal size) complete as per design.

Making connection of drain or sewer line with

existing manhole including breaking into and making

good the walls, floors with cement concrete 1:2:4

mix (1 cement : 2 coarse sand : 4 graded stone

19.21 aggregate 20 mm nominal size) cement plastered on

both sides with cement mortar 1:3 (1 cement : 3

coarse sand), finished with a floating coat of neat

cement and making necessary channels for the drain

etc. complete :

For pipes 100 to 250 mm diameter

Constructing brick masonry circular type manhole

0.91 m internal

dia at bottom and 0.56m dia at top in cement mortar

: 4 coarse sand), inside cement plaster 12 mm thick

mortar 1:3 (1 cement : 3 coarse sand) finished with

a floating coat

of neat cement, foundation concrete 1:3:6 mix (1

cement : 3 coarse

sand : 6 graded stone aggregate 40 mm nominal

size), and making

necessary channel in cement concrete 1:2:4 (1

cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal

with a floating coat of neat cement, all complete as

0.91 m deep with SFRC cover and frame (heavy

20 grade designation) 560 mm internal diameter

to I.S. 12592, total weight of cover and frame to be

less than 182 kg., fixed in cement concrete 1:2:4 (1

: 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including centering, shuttering all

(Excavation, foot rests and 12mm thick cement

the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

SURFACE DRAIN (250X150 MM)

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m,

as directed by Engineer-in-charge.

2.6.1 all kinds of soil 43.00 cum 177.50 7632.50

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

2 2.25 not exceeding 20cm in depth: consolidating each 11.00 cum 196.00 2156.00

deposited layer by ramming and watering, lead up to

50 m and lift up to 1.5 m.

Qty. = 25% of them no 1

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Providing and laying in position cement concrete of

3 4.1 specified grade excluding the cost of centering and

shttering - All work up to plinth level

1:5:10 (1 cement : 5 coarse sand (zone-III): 10

graded stone aggregate 40 mm nominal size).

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived

4 4.1.4 from natural sources : 4 graded stone aggregate 40 3.00 cum 7780.30 23340.90

mm nominal size derived from natural sources)

Centering and shuttering including strutting,

propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for

Brick work with F.P.S. bricks of class designation 75

in foundation and plinth in :

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 7.00 Cum 7132.25 49925.75

12 mm cement plaster finished with a floating coat

of neat cement of mix :

External Electrification

Earthing with G.I. earth plate 600 mm X 600 mm X 6

mm thick including accessories, and providing

1 DSR 5.4 masonary enclosure with cover plate having locking 1.00 Sets 7472.00 7472.00

arrangement and watering watering pipe 2.7 metre

long etc. with charcoal/ coke and salt as required.

Earthing with Cu. earth Plate 600mm x 600mm x

3mm thick including accesssories, and providing

masonary enclosure with cover plate (CI heavy

duty) having locking arrangement and watering pipe

pipe of 2.7 mtr long etc. with charcoal or coke and

salt) as required.

Supplying and laying 25 mm X 5 mm G.I. strip in 40

mm dia G.I. pipe from earth electrode, including

connection with G.I. nut, bolt, spring, washer

excavation and refilling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on

surface or in recess for connections etc. as required.

2 nos used for 50 x 5 for the Neutral earthing of

Providing and fixing 25 mm X 5 mm G.I. strip on

surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface

or in recess for loop earthing etc. as required.

Supplying, fixing, testing and commissioning of

7 NSI-1 following bare Copper/ GI flat including all necessary

fixing accessories and effecting connections.

Supply and laying medium class GI pipe under

road/paved areas/wall crossing etc. including earth

excavations refilling, ramming and making good as

8.1 NSI-2.1 150 mm dia GI pipe Class B 10.00 Metre 1600.00 16000.00

SUPPLYING & LAYING OF CABLE

Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

following size direct in ground including excavation,

sand cushioning, protective covering and refilling the

Laying of one number additional PVC insulated and

PVC sheathed / XLPE power cable of 1.1 KV grade of

following size direct in ground in the same trench in

one tier horizontal formation including excavation,

sand cushioning, protective covering and refilling the

trench etc. as required.

DSR /NSI RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR

Supply of following sizes of XLPE insulated

Aluminum conductor strip/ wire Armoured, overall

PVC sheathed 1.1 KV grade cables conforming to

relevant IS-7098 Code and technical specifications.

Supplying and making end termination with brass

compression gland and aluminium lugs for following

4 DSR 9.1 size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade

Supplying, installation, testing and commissioning of

65W LED Street Light IP66 LED with High

performance having system lumen output of

minimum 9900 lumens, contemporary designed

1 NSI-1 housing made of die-cast aluminium, with street 4.00 Nos 7634.33 30537.32

optic LENS for uniform light distribution. PF better

than 0.9, CRI better than 70 complete with all

accessories. Wipro Cat No.: LR 02-102-XXX-57-G2

SITC of 6m ht. GI pole alongwith control box,6A MCB

etc. as required for St. height

GRAND TOTAL 40068890.26

GRAND TOTAL 40068890.26