SPECIAL REPAIR TO EXISTING RANGE AT VSN NAGPUR

Amount

Surface Excavation not exc 30 cm deep and averaging n exc 15 cm deep and getting out in Hard/dence soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

M&L for PCC (1:4:8) type D-2(using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Demolition of cement Concrete(unreinforced) in ground floors and pavings,drains etc n exc 15 cm thickness (below or above ground level) including floor finishes/tiling works and disposal of debris complete all as specified and directed.

Demolition of Brickwork or stone /boulder masonry built in cement mortar complete all as specified and directed.

M&L for Brickwork with sub class 'B' Bricks , straight or curved in plan exc 6 m mean radius built in CM(1:6) complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

M&L for Damp proof course to horizontal or vertical surfaces in 1:2:4 type BO 25 mm thick including necessary formwork complete all as specified and as directed.

Taking down cement plaster on brick or stone wall,concrete, etc including racking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

M&L Rendering 15mm thick on Brick in CM 1:6 including finishing even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick in CM 1:4 as in Brick including finishing even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI Marked complete all as specified and directed.

M & L Preparation of Newly plastered external wall surfaces by applying two coats of cement base paint over a coat of primer complete all as specified and directed

M & L Preparation of Newly plastered wall surfaces by applying two coats of distemper oil emulsion over 3mm thick wall care putty complete all as specified and directed

Returning and filling in including spreading, levelling, watering and well ramming in layers n exc 25 cm thick complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M & L for Hardcore of gauge n.exc 63mm deposited ,spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-2, using 20mm graded stone aggregate, 75 mm thick as in plinth protection complete all as specified and directed.

M&L for plain Cement concrete (1:2:4) type -B1 using 20mm graded aggregate, 40mm thick as in floor, fair finish with using extra cement complete all as specified and directed.

S&F glass dividing stirrups 38mm wide and 3mm thick inserted in position conforming to design complete all as specified and directed.

M&L 75mm thick cement concrete using (40mm graded aggregate) type D-2 (1:4:8) as in sub-base complete all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n.exc 15 cm thick ,spread, levelled and rammed including watering complete all as specified and directed.

M&L for Reinforced Concrete Cement 1:1.5:3 Type A1 Nominal mix as in as in lintel beam, over 1.50m span complete all as specified and as directed.

M&L Cement concret(1:3:6) TypeC-2 using 40mm graded stone aggregate as in surface channel and drain complete all as specified and as directed.

M&L PCC coping (1:2:4) type B-1(using 20mm graded stone aggregate) as in coping complete all as specified and directed.

M&L for Providing cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) ,water troughs and the like including weathering slightly rounded or chamfered angles and throating in drains etc complete all as specified and directed.

M&L Fair finished with using extra cement to skirting, drain etc complete all as specified and directed.

Taking down of chowkat with shutter without taking off shutters from the frame n.exceeding 1.5 sqm all as specified and as directed.

Taking down of chowkat with shutter without taking off shutters from the frame exceeding 1.5sqm and n.exc 4 sqm each all as specified and as directed.

M & L PCC 1:2:4 type B2 100 mm thick (using 40mm graded crushed stone aggregate) as in HardStand surface finished even and smooth without using extra cement all as specified and directed.

M & L forming contraction joints (dummy) joints 30 mm deep x 10mm wide filled with sealing compound grade 'B' complete all as specified and directed

M&L for Framed work such as grills,gratings,etc with ends of bar shouldered and or rivited or forged into spikes framed guarded bars barred iron doors ladders framed balusters walkways railings framed work of water tank stand similar work confirming-290 Gde-E-165 complete all as specified and directed.

S&F Mild steel Screw bolts (machine made) with hexagonal or square head at one end and screwed the other end n.exc 5 cm long and diameter of neck exc 5 mm but n exc 10mm dia complete all as specified and directed.

M&L Mild steel plates (plain or chequred) channel squre cut notched ordinary and counter sunk forming holes without any attachment for Fe-410w grade E-250 quality A complete all as specified and directed.

M&L Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roofcoverings all as specified and directed

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed

S&F Pre- painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

M&L Applying 2 coats of Synthetic Enamel paint over a coat of Red Oxide zinc chrome primer on steel surface over 10 cm girth including preparation of surface complete all as specified and as directed.

S&F Butt hinges, Heavy weight, cold rolled mild steel, size of hinges 100 mm complete all as specified and directed

S&F Extruded Aluminium bow handles of size150 mm complete all as specified and directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled forfixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or slidingwith and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

M&L Mild steel plain,black sheet for covering to steel gate and similar work, cut to size, holes pucched,including round heatedscrews 1mm thick complete all as specified and directed

S&F Pressed steel frames for chowkat of size 105x60mm, hinges 100mm size (3 Nos each chowkat) with one or more rebates including necessary fixing lugs, lock strike plate, etc complete all as specified and directed.

M&L for PCC(1:3:6) type B1 for filling to Pressed steel chowkat and Holdfast complete all as specified and directed.

S&F Steel Windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars docetailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges,steel peg stay complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed block for hold fast & filling in pressed steel door frame completed all as specified and directed.

M&L for Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane all as specified and as directed.

Excavation in post holes ( or similar holes) in any type of soil each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with eath around, in layers n.exc 25cm , watering, and removing surplus soil to a distance n.exc 50m and making good surface completed all as specified and directed.

M&L PCC (1:2:4) type B-1(20 mm graded aggregate) for embedding post completed all as specified and directed.

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt weldedtubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 52 above here-in-before but 5mm dia and over upto and including 10mm dia in stirrups spacers and binders complete all as specified and directed.

Demolition of cement Concrete(reinforced) of any description and in any position not otherwisespecifically provided for complete all as specified and directed.

M&L Providing precast cement concrete 1:2:4 type B-1 (using 20mm graded stone agg) as in drain covers set in cement motar 1:6 all as specified and directed including necessary formwork and moulds complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc.completed all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracketframing (Beam, tee, angle, channel or flat sections) includingdistance pieces, cleats etc completed all as specified and directed.

Fabrication and Fixing only(using old dismantled) roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracketframing (Beam, tee, angle, channel or flat sections) includingdistance pieces, cleats etc completed all as specified and directed.

M&L for Preperation of old painted surfaces of steel &iron work of any discription not specifically mentioned otherwise over 10cm width or girth and applying two coats of synthetic enamel paint all as specified and as directed

Supply only for good quality Fine Sand as per site requirement at firing range complete all as specified and directed by Engr-in-Charge.

Supply only for good quality Saw Dust as per site requirement at firing range complete all as specified and directed by Engr-in-Charge.

Labour only for spreading, levelling and well rammed including watering as required Fine Sand as per site requirement at firing range complete all as specified and directed by Engr-in-Charge.

Labour only for spreading and levelling the mixure of fine sand and saw dust in 1:1 ratio at firing range at a specific height approx 5 to 6 mtr from grounfd level with a slope of 60 to 70 degreecomplete all as specified and directed by Engr-in-Charge.

Dismantling/Taking down and Re-fixing/erecting of Old steel tubular swaged poles any type with accessories/fittings at other location as directed including necessary excavation, removal of soil, refilling of soil, PCC (1:3:6) type C-2 using 40 mm graded stone aggregate for foundation of pole and coping with PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete including painting of poles with two coats of aluminum paint over one coat of priming and numbering of poles complete etc and dismantling of pole complete

Dismantling/Taking down and Supply, Installation, Testing and Commissioning of LED aviation light comprising of aluminium housing with polycarbonate enclosure, 302 nos. LED are provided AC Circuit, 230 volts with all components and fixing arragements on pipe necessary flat iron clamps, nuts, bolts & washers etc including necessary wiring circuit all as specified and as directed. Make Bajaj cat No 110731 BGAV 302 LED or equvalant

Dismantling/Taking down and Supply, Installation, Testing and Commissioning of LED flood light 135 watt with a nominal system lumen output of 4500 lumens and a minimum system efficacy of 100 lumen/watt. The luminaire shall have rated system lifetime of 50,000 burning hours at L70. The luminaire should have cool white colour temperature (5700K) and a CRI>70. The luminaire shall meet IP65 rating with THD<20% & Pf>0.9. The luminaire housing should be made of pressure die cast aluminium. The total power consumption should not exceed 135 (including driver).Make CG Cat No LFLN-135-CDL/60 or equvalant

Dismantling/Taking down and Supply and fix 2 core 2.5 sqmm PVC insulated PVC sheathed weather proof multistranded Copper conductor cable 1100 volts grade including GI conduit on pole,wall etc with MS clamps all as specified and directed.

Dismantling/Taking down and Material and labour for service cable of PVC insulated, unsheathed aluminium multi stranded conductor twin core 6 Sqmm size complete all as directed

Supply and fix 15 mm dia GI tubes light grade with all fitting from wall to LED aviation light fittings with clamps, nuts & bolts complete all as specified and as directed

Dismantling/Taking down and Supply & fixing MCB, SPN, 10 amps of 10 KA with Plastic enclosures including incoming and outgoing connection complete all as directed. Make : Legrand or equivalent

M & L for Earthing complete with galvanised steel plate electrode, 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to earthing lead of 4 mm dia galvanised iron or steel wire all as shown in plate No. 4 of SSR PART 1 of 2009 to the earthing test point all as specified and as directed. Note :- the cost of excavation and earth work PCC pit and RCC cover funnel & watering pipe, wiremesh, charcoal dust and common salt earth lead protection pipe upto 7.5 Rmt shall be deemed included in the unit rate for earthing all as specified and as directed.

M & L for point wiring (concealed) on walls and surface on ceiling complete with FR PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable modular boxes ,switch plates of suitable make and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed. (a) One light point controlled by one switch

(b) One switch socket outlet modular type 3 pin 6 amp on same board.

S & F LED security light fitting 25 Wmade out of pressure die cast aluminium powder coated housing high impact resistant 4 mm thick toughened glass cover and matrix of power LEDs in built electronic driver up to 4 KV surge protection fitted with adjustable pole adopter to enable on site tilt angle setting and input power 25 W system lumens 85/W operating voltage 160-260 V of make : CG Cat Part No. LSTS-25-CDL :- Note :(i) Rates are deemed to be included for security ligh brackets made out of 25 mm / 20 mm dia GI medium grade tubing of suitable length and bend to shape including fixing MS flat iron clamps, bolts & nuts as per site requirement complete in all respect complete all as specified and as directed.

Supply and fix master led tube 4ft 20 W LED Tube . nominal system lumen output of 2100 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 40,000 burning hours at L70.The luminaire should have a color temperature of 6500K and CRI>83. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 18W (including driver). Make : Phillips/CG/WIPRO

S & F decorative box type fitting with blue coloured end caps pre wired for LED tube energy of 20 Watt . Make : Phillips/CG/WIPRO

S & F Surface mounting LED Luminaries and 1 x 9 Watt LED fitting with connecting up with copper 3 core flexible cord of minimum size 1.5 Sqmm size complete all as specified and as directed . Make : CG, Phillips, Wipro

S & F Switch modular type, single pole one way 6 Amps, 250 volts Ac suitable for modular switch boxes without indicator, all as specified and as directed. Make : Legrand Cat No. 675501

S & F socket modular type single pole one way 6 Amps multistandard 250 volts all as specified and as directed. Make : Legrand Cat No. 675554

M & L for ceiling rose, surface bakelite, 65 x 50 mm, two to three terminals all as specified and as directed.Make : Leader, Anchor

M/s Jagdish Staioners and General Stores

M/s M.G. Hargunani

Vishwakarma Engineering Works

dhanshree enterprises

Harsh Construction Company

M/S J.A CHAWHAN