SPECIAL REPAIR TO BUILDING NO T-86 JCO MD ACCN AT MIRAN SAHIB UNDER GE JAMMU

Amount

Taking down cement plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

15mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement including necessary scaffolding, complete all as specified.

15mm thick rendering in CM 1:3 on other than fair faces of stone masnory/brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

15mm thick rendering in CM 1:4 on fair faces of stone masnory/brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

10mm thick rendering in CM 1:4 with liquid water proofing compound Pedilite LW plus @ 200 ml per 50 Kg of cement on concrete surface such as soffits,RCC,chajja, roof projection etc complete all as specified and directed by Engr-in-Charge.( Note : WPC will measured and paid separately as supply only.

Applying one coat of cement wall putty of minimum 2mm thick over plaster surface of wall complete all as specified and directed.

Preparation of surface and applying two coat of oil bound distemper over wall putty surface complete all as specified and directed.

Preparation of new wall surface and applying two coat of cement base paint over chalk whiting on plastered surface complete all as specified and directed.

Preparation of surface and applying three coat of white wash on newly plaster surface of ceiling complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

Pressed steel frames(Factory made)made out of 1.25mm thick black MS sheet for doors with two rebates for fixing one shutter including necessary fixing lugs, hinges, lock strike plate, etc., complete,size of frame 105X60mm incl bottom of each chowkat to be welded with 2 Nos.25X25X3mm thick flat iron projecting 10cm on either side complete all as specified and directed.

All as per Item No. 12 here in before but size of frame 125X60mm for fixing of two shutters complete all as specified and directed.

All as per Item No. 12 here in before but size of frame 60X40mm complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Factory made solid panel PVC Moulded Door Shutter with particle boardcore, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC Sheet on the front face & 2mm thick plain colour PVC sheet on back face supplying & fixing in frame at site as per specification & drawing .

35mm thick factory made wooden moulded panel door shutter with masonite facing on both side of (two,three,or four panel design as approved) made of solid core using machine filled rigid expanded polyurethane foam and the door facing plate shall be 3.2mm thick complete all as specified and directed.

35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

Box type steel windows (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on exterrnal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 Nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3. Notes:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface. (ii) 4 Nos MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) PCC block for embedding lugs. (iv) Cooler windows where required.including 10 mm dia mild steel framed works such as grills, framed guard bars, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and directed

18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing with lamination,incl teak wood liping 6mm thick on sides complete all as specified and directed.

6mm thick teak wood lipping over prelaminated particle board, fixed with nails complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in back filling, bed block for hold fast, coping, benching on corner of joints etc complete all as specified and directed.

100mm size butt hinges medium weight cold rolled stainless steel complete all as specified and directed.

Aluminium handles D type anodised 150mm long ISI marked complete all as specified and directed.

Aluminium handles D type anodised 125mm long ISI marked complete all as specified and directed.

150mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

125mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

250mm long and 16mm dia aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

Hasp and staple, 100 mm size safety type aluminium anodised including bolt to hingesplate and fixed with screws complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue 140 mm size anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Mild steel 150mm, ordinary rat tail rod pattern springs including roller & roller plate complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm size and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Preparing surfaces of new wood and wood based material of any description and girth, not otherwise described, and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparing surfaces of new steel material of any description and girth, not otherwise described, and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 using 12.50mm graded crushed stone aggregate as in floor surfaces, complete all as specified and directed.

Screed bed or bedding layer of mortar 15mm thick for laying floor finished in CM 1:4 complete all as specified and directed.

Non - skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but n.exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed.

Non - skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but n.exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed.

10mm thick rendering in CM 1:3 other than fair faces brick work even and fair faces to receive tiles complete all as specified and directed.

All as per item No.41 here -in- before above but as in skirting complete all as specified and directed.

Glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles , complete all as specified and directed by Engr-In-Charge.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl taking down old complete all as specified and directed.

Screed bed or bedding layer of mortar 20 mm thick for laying floor finished in CM 1:4 complete all as specified and directed.

Machine cut kota stone slab flooring not less than 19mm thick as in floor to match the shade of the slab incl rubbimg polishing up to mirror finish complete all as specified and directed.

Machine cut kota stone slab flooring not less than 19mm thick as in riser of steps, skirting, dado to match the shade of the slab incl rubbing and polishing up to mirror finish including 10 mm thick plaster in CM 1:3 complete all as specified and directed

75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floors to receive top layer complete all as specified and directed.

Factory made precast machine crafted cement concrete M-40 grade antiskid tiles of size 300x300x22 to 25 mm polymer moulded using white cement and pigments as per design/pattern approved laid over and including screed bed 15mm in CM 1:6 complete all as specified and directed.

Demolition of concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

75 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection etc finished even and smooth with out using extra cement complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

15mm bore tubes medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

20mm bore tubes medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Refixing old 15mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Refixing old 20mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Dismantling PVC water tanks and removing to storing capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified.

Rotational moulded polythylene water storage tank with float valve, plastic lid cover, triple layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 1000 litre incl making connections complete all as specified.

Supply and fixing in repairs Vitreous chinaware wash hand basin white, flat back of size 450x300 mm including CP pillar tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets and CP waste coupling complete and waste pipe and all as specified.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests and P or S trap connection to flushing pipe ,antisyphonage pipe complete including provision of cement concrete bedding complete all specified in SSR Part-I complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern,10 ltrs capacity low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

PVC connection 15mm bore size with PTMT nuts of length 600mm fixed in repair, complete all as specified and directed.

15mm bore bib taps long nose/long body, cast copper alloy cp with capstan handle screwed down , screwed for brass , weight not less than 450gms ferrule and fixed complete all as specified and directed.

15mm bore angle valves, cast copper alloy CP , half turn, screwed down, high pressure , with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions complete all as specified and directed.

15mm bore brass stop cock, cast copper alloy CP with long shank and cup (concealed type), high pressure, with capstan handle screwed down , screwed for brass , weight not less than 450gms screwed both ends for iron pipe or for unions complete all as specified and directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

15mm bore gun metal, globe or gate valve with iron wheel head , screwed both ends for iron pipe complete all as specified and directed.

Gun metal,20mm bore globe or gate valve with iron wheel head , screwed both ends for iron pipe complete all as specified and directed.

Shower rose brass chromium plated with swivel joint of size 125mm cast copper alloy type complete all as specified and directed.

Taking up or down CI/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints and removing lead of 110/100/75mm dia pipe complete all as specified and directed.

Cast iron soil, waste and vent pipes of bore 100mm in any length with or without ears, with cement joints fixed to wall complete all as specified and directed.

Cast iron soil, waste and vent pipes of bore 75mm in any length with or without ears, with cement joints fixed to wall complete all as specified and directed.

75 mm bore cast iron bends (any radius) with oval access doors complete all as specified and directed.

75 mm bore CI branch pieces (Tee), single (equal or unequal )ordinary or inveeted ( spigot or socket type) or with parallel branches with oval access complete all as specified and directed.

100 mm bore CI branch pieces (Tee), single (equal or unequal )ordinary or inveeted ( spigot or socket type) or with parallel branches with oval access complete all as specified and directed.

Cast iron vent cowl 100mm size complete all as specified and directed.

Cast iron vent cowl 75mm size complete all as specified and directed.

Stack clamps out of 50mmX5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75mm bore pipe complete all as specified and directed.

Stack clamps out of 50mmX5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and directed.

Cast iron floor trap OF SIZE75/100mm with stainless steel grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed.

20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) complete all as specified and directed.

Brass CP towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed.

Brass CP towel ring 20mm dia 'D' type 60cm long between flanges complete all as specified and directed.

MS peg set of six powder coated as approved by GE complete all as specified and directed.

Drapery curtain rod of metalic 20mm dia covered with PVC coating including with MS bracket, end ball, rounded block (Coated with brown/cherry/goldencolour ) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with raw plug and steel screw complete all as specified and directed.

Harison rails, aluminium anodized with fixing brackets ,stops,rollers etc as in cubboard complete all as specified and directed.

Glass shelf rectangular size 450mm X 150mm , 5mm thick glass with stainless steel bracket as approved and sample kept in AGE B/R office complete all as specified and directed.

Cabinet mirror of PVC moulded size 600MM X 450MM as approved and sample kept in AGE B/R office complete all as specified and directed.

Sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washers and wastes pipe; including bedding in cement mortar on wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Stainless steel plate rack of size 600mm X 900mm fixed with washer and plugs complete all as specified and directed.

Providing precast cement concrete louvers and jallies made out of cement concrete type B0 1:2:4 (using 12.5mm stone aggregate) set in CM 1:6, 50mm thick (measured solid), including all mouldings and taking down old jallies complete all as specified and directed.

Demolition of lime concrete of any description and in any position and removing the rubbish from work site complete all as specified and directed.

Special treatment to sunken portion with 15mm thick plaster in cement mortar 1:4 (with integral water proofing compound both on floor and wall,The surface shall be cured and allowed to dry and apply epoxy resins coating polymer modified cementations coating like brush bond of fosroc ,pedilite and bostic shall be laid to a slope of 1:40 outwards with 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall ,floor area of WC and bath upto 2.0 Sqm all as specified and directed (Note:- GI spout 25mm dia light grade .PCC 1:4:8 type D2, PCC 1:5:10 type E2 and WC/EWC shall be measured and paid seperately under relevant item).

Providing cement concrete 1:5:10 type E2 using 40 mm graded stone aggregate as in filling in sunken portion complete and specified and directed.

75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate 75mm thick as a base in sunken portion complete and specified and directed.

M&L for GI spout 25mm dia light grade ,fixed to walls as directed by Engineer -in-charge complete and specified and directed.

Demolition/removing of existing roof treatment of any description in any condtion including removing of top surface and removing all the debris to a distance n.exc 100m

Roughening surfaces by sweeping clean and washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3kg/sqm over cleaned surfaces complete all as specified and directed.

20mm thick cement screed in CM 1:4 mixed with liquid water proofing compound Pedilite LW plus @ 200ml per 50 kg of cement finished surface even and smooth or laying of water proofing membrane complete all as specified and directed.(Note: WPC will measured and paid separately as supply only).

Roof Treatment with the following specification :- (a) Cleaning the entire roof surface throughly to remove all loose particles dust/dirt particle and applying with one coat of industrial bituminious 85/25 grade at the rate of 1.20Kg/Sqm over the plastered surfaces of roof complete all as specified and directed.. (b) Applying a layer of APP based Polymeric Memberance 3mm thick (Minimum) weighing 3.5 Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160 gms per sqm by torch application. The overlap shall be minimum 100 mm on traverce direction and 75 mm on longitudinal direction and sealing overlap by torch application. (c) Applying evenly one coat of Aluminium paint @ 0 .10 Ltr per sqm over the APP based polymeric Membranecomplete all as specified.

Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel', complete all as specified

Supply only liquid water proofing compound.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

Plain cement concrete 1:3:6 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement

PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in mass concrete in foundation complete all as specified.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down old and unserviceable submain wiring any size of two core and including earth wire complete including batten /conduite and make good the disturbed surface to match the existing surface , complete all as specified and directed.

Taking down carefully unsv main switch / DBs alongwith MCBs / wooden board / connected fittings & fixtures any type and making good distrubed surface of walls and roofs to match the existing surface, complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked 25mm dia terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc for one light/fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

Description all as per item No.113 above but for 3 Pin socket outlet 5 Amps point on independent board with PVC insulated copper conductor cable 1.5sqmm complete all as specified and directed.

Description all as per item No.113 above but for one bell / buzzer point controlled by one 5 Amp switch complete all as specified and directed.

Description all as per item No.113 above but for one light point controlled by two way switch complete all as specified and directed.

Description all as per item No. 111 here in before but for 3 Pin socket outlet 15 Amps point on independent board other switches with with PVC insulated copper conductor cable 2.5sqmm 1100 Volts grade, complete all as specified and directed.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Bell push piano flush type 6 Amp, (ISI marked), complete all as specified.

Switch flush type 6 Amp single pole two way, (ISI marked), complete all as specified.

Switch piano flush type 15 Amp single pole one way, (ISI marked), complete all as specified.

Socket outlet multipurpose combination 2 in 1, 5 Amp flush type universal, complete all as specifed.

Socket outlet multipurpose combination 3,5 pin 15 Amp shuttered type, complete all as specifed.

Fan regulator stepped type (electronic ) flush type for 1200/1400mm sweep AC ceiling fan, fixed in repair complete all as specified. .

Taking down of existing ceiling fan and re-fixing the same after necessory repair / rewinding and any unserviceable spare parts like bearing, bush ,pvc connector with provn of MS hook of suitable size and length if required at site and making connection with 3 core copper cable of required size including painting whereas required of size 1200/1400 mm sweep complete all as specified & directed.

New generation energy saving,wall mounted LED Tube light fitting 20 watt wall mounted LED batten rod extruded aluminium heated sink provided for efficient heat dissipation and integrated electronic driver 20 watt LED 6500 k (4 feet long) with Led rod of 20 watt , complete all as specified.

Self ballast LED retro fit lamp with PVC body and PC diffuser 9 watt 230 volt 6500k complete all as specified and directed.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Ceiling rose (ISI Marked) 3 terminals PVC/poly carbonate, insulated body, compete all as specified.

Submain wiring using two single core PVC insulated cables with copper conductor(FRLS) of size 6 sq.mm (nominal area) & drawing into conduit including provision of 4 sq.mm copper conductor(FRLS) PVC insulated earth wire including taking down old wiring complete all as specified.

Sheet metal enclosure factory made (Double door) for DBs, Triple pole and neutral, 240 volts, 4 way with 200 Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

Sheet metal enclosure factory made phosphatised, powder painted MCB DBs, 240 volts, 8 way without bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

MCB triple pole and neutral 63amps 415 volts 50 Hz, B 'series ' 10 KA breaking capacity, complete all as specified.

MCB single pole and neutral 40-50 amps 240 volts, fixing in replacement, complete all as specified and directed.

MCB single pole and neutral 32 amps 240 volts fixing in replacement, complete all as specified and directed.

MCB single pole and neutral 6-32 amps 240 volts fixing in replacement, complete all as specified and directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

BULK HEAD, luminaries IP65 with opal diffuser 10watts,230 LED type complete all as specified and directed.

Excavation in trenches in Hard type of soil not exceeding 1.5m wide and n.exc 1.5 mtr in depth for laying of under ground electric cable and getting out complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified.

Removing excavated surplus materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified.

Dry river sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- (a).Dry fine sand of best available quality shall be used. (b).Punned thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Supply and laying or fixing or passing through pipe and testing 1100 volts grade heavy duty electric cable with PVC insulated of size 25 Sqmm ,3x1/2 core armoured LT cable aluminium stranded conductor 1100 volt grade including jointing and testing as required at site,complete all as specified and directed.

Taking down carefully existing serviceable meter box along with Energy metre from building for reconditioning of meter box and setting aside the energy meter for refixing. Then applying syhnthetic enamal paint on meter box as directed by Engineer in charge at site and refixing the same after changing its hinges, screws, lock system etc including refixing of energy meter at the same meter box including repair or replacement of MCB TPN box and also making good distrubed surfaces to match with the existing finishes, complete all as specified and as directed. Note:-Energy meter will be handed over to MES store at the time of taking down and will collect from a store after completing the whole work at site for refixing.

GENESIS INDIA

M/S A TO Z ENGINEERS