Day to day maintenance of Staff Quarters at BSNL Compound CTX and Akashpuri in Prayagraj BA.

Amount

PART - A : GENERAL SERVICES

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing manual assistance for attending petty day-to-day maintenance services related to Plumbing / Carpentary/ Masonary as & when required i/c all required T&P and scaffolding etc. (Note: Minimum time shall be reckoned as half day even if the time required for doing the job is less than half a day.

skilled manual assistance

un killed manual assistance

Removing blockage of floor trap, WC trap, RW pipe and sanitary pipes etc.including cleaning of pipes/ traps and disposal of garbage found to the nearest sewage dump etc complete. (Note: Rate includes the cost of necessary t&p, bamboo, rubber choke, etc.)

Cleaning of silt, saplings, fungi, dust from the roof top PVC/ RCC water tanks i/c its disposal outside compound, washing tanks with lime water and treating with potassium permanganate or bleaching powder etc. all complete as per direction of Engineer-in-charge.

Capacity of tank upto 500 litres.

Cleaning of sewer line including manholes in the compound by complete removal of earth, silt, sludge, brick bats, garbages etc and disposing off the same outside the compound at the authorized municipal dump complete as per the direction of the Engineer-in-Charge.

Sewer manholes of all sizes and depth.

Removal of sludge, sewage etc. from septic tank (upto 100 user) by mechanical or manual means and cleaning the same in and around with water and disposal of sludge, sewage outside the compound to an authorised municipal dump outside the township as per direction of Engineer- In- Charge.

Cleaning of open surface drain and stacking of garbage within 50 metre lead all complete as per direction of Engineer - In- Charge.

Cleaning of all roof top i/c mumty of staircase, khurra under side of water tank etc. by removing silt, algae etc. and disposal of mulba to an authorised municipal dump outside Teelcom compound as per direction of Engineer-in-charge.

T- II Qtrs

Type-III qtrs

Type-IV

Type-V

Type-VI

Uprooting & removal of wild growth of vegetation by spraying suitable herbicides like glyphosate products / or manually i/c repairing damaged wall surface if any , from terrace, walls, drainage system, water supply system or at any location of the building as directed by the Engineer-in-charge.(one wild growth shall be considered as one job)

Providing and fixing PVC cover of approved make having proper locking arrangement over PVC water storage tank of capacity 250 to 500 ltr. capacity.

Providing and fixing white vitreous china water closet squatting pan (Indian type)

Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

Black solid plastic seat with lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400 mm.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

P/F c.p. brass towell rail of approved quality Number i.c screws complete as directed (i) 600mm long.

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:

Kitchen sink without drain board 610x460 mm bowl depth 200 mm.

Providing and fixing stainless steel jali (grating) with or without hole for waste pipe for floor/Nahani trap.

100 mm dia. weight not less than 100 gms

PART -B: PLUMBING

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

15 mm nominal outer dia. Pipes.

20 mm nominal outer dia. Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia. Pipes.

40 mm nominal outer dia. Pipes.

50 mm nominal outer dia. Pipes.

BRASS FITTINGS

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :

15 mm nominal bore.

20 mm nominal bore.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Circular tank

C.P. Brass Fittings

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

P/F C.P. brass pillar tap of approve quality (a) 15 mm nominal bore.

P/F C.P. brass soap dish upto dia 150 mm or oval shaped as approved by Engineer-in-Charge.

PTMT Fittings

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT pillar cock of approved quality and colour .

15mm nominal bore, 107 mm long. Weighing not less than 110 gms.

Providing and fixing PTMT grating of approved quality and colour.

Circular type.

100 mm nominal dia.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

15 mm nominal bore, 105 mm long. Weighing not less than 138 gms.

20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

P/F P.V.C. handles /lever in PVC Cistern complete as required .

Repairing of the following i/c other fittings of C.P. brass etc. as per direction of Engineer-in-charge.

Low level cistern i/c required integral fittings/ fixtures.

Repairing of leaking toilet joint with P trap and floor traps.

Repairing of leakage in main and branch water pipe lines of 15 mm to 25 mm as and when required i/c the cost of jointing material such as Teflon tape, jute,tee,elbow,socket etc. required for sealing of leakage joints. Pipe & union, if required to be replaced, shall be paid separately.

Checking and making good all leakages etc. in SCI, CI pipes of 4" to 6" dia.complete as per the direction of Engineer-in-charge. (Major fittings etc. to be paid separately).

P/F C.P.brass waste coupling for wash basin / sink of approved quality

32mm nominal size.

40mm nominal size.

50 mm nominal size.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing soil, waste and vent pipes :

100 mm dia.

Sand cast iron S&S pipe as per IS: 1729.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i)Single socketed pipes.

75 mm diameter

110 mm diameter

PART-C: CARPENTARY SERVICES

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of thickness 4 mm.

Deduct for not providing hinges in doors, windows or clerestory window shutters with :

Stainless steel butt hinges with stainless steel screws :

For 2nd class teak wood and other class of wood shutters.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.

300 mm weighing not less than 200 gms.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

20 mm dia (heavy type)

Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory windows using galvanised M.S. wire gauze with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm.

Arranging electric welding machine at site for repairing works etc. with necessary cables and other T&P including the cost of operator and electrodes but excluding the cost of necessary steel sections complete as per direction of Engineer-in-charge. (Note: One day work at one site shall be taken as one job.)

Providing and fixing M.S. handle to side steel windows including bolts, nuts and washers etc. with necessary welding and machine screws etc. complete. .

100 mm long

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

PART-D: MASONRY SERVICES

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

With cement mortar 1:4 (1 cement : 4 fine sand).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

40mm thick with 20mm nominal size stone aggregate.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mmnominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground within 50 metres lead.

Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska :

With modular brick tiles

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Clearing path ways as well other portion of campus by trimming tree branches such as Bargad, Mango, Guava, Neem, Sagaun, Ashok, Eucalyptus/other trees etc. as and when required upto 30 Feet height,wherever applicable, i/c cost of T & P and disposal of unservicable material to the municipal dump all complete as per direction of Engineer-in-charge(payment shall be made for each tree once in a year).

PART-E: CREDIT TO WORK

Credit to work the old unserviceable Brass/CP Brass Bib Cock, Stop cock, Pillar Cock Gate Valve and other fittings etc.

Credit to work old damaged PVC. sanitary/water supply fittings.

Credit to work old rusted (unserviceable) C.I./S.C.I. Pipes and fittings, Mild Steel/ Steel Sections, G.I./M.S. Pipes etc.

Credit to work old damaged wooden items.

Credit to work SAP wood retrived from trimming of trees.

Sadhana construction company