Hardscaped and Softscaped Development from Airport to Hinoo Chowk in Ranchi Jharkhand.

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classification of soil item - B).(same quanity as of excavation)25% of excavation

Clearing grass and removal of rubbish up to a distance of 50 meters outside the periphery of the area

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing brick Bats soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75B one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : Cement mortar 1:6 (1 cement : 6 coarse sand)

"Providing and laying 25mm thick. Kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (lime putty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royality all complete as per building specification and direction of E/I. (iv) 600 x 600 mm size"

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and laying tactile tile (for vision impaired persons as perstandards) of size300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Providing and laying in position ready mixed or site batched M25 design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works upto plinth level

Providing and laying in position ready mixed or site batched M25 design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll works above plinth level upto floor V level

Centering and shuttering including strutting, propping etc. and removal of form for |Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form lintels, beams, plinth beams. girders. bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts.

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 (Only valid for sAlL & TATA Steel

Providing Tor steel reinforcement of 10mm. Dia. bars as per approved design and drawing -do- -do -

Providing Tor steel,reinforcement of12mm,16mm, 20mm, 25mm, bars as per approved design and drawing -do- -do- TMT bar Fe 500 (Only valid for SAIL & TATA Steel) JSPL, and Vizag Steel)

Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of FM 1.5 with 5% cico or any other approved water proofing compound including screening, curing, with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l. Boundary Wall grill / gate

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. Red sand stone

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme onthe boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

(Dismantling of flexible pavement) Dismantling of flexible pavements and disposal of dismantled materials upto a lead of 1000 metres, stacking serviceable and unserviceable materials separately (By mechanical means) (Bituminous courses)

Construction of Subgrade and Earthen Shoulders (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2) Rolling with vibratory roller

(Granular Sub-Base with Graded Material (Table:- 400-1))Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.(Grading-V) (By mix in place method)

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing )

Plain/Reinfoced Cement concrete in open foundation complete as per drwaing and technical specifications.(PCC Grade M15 using batching plant & concrete pump)1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size)

Providing brick Bats soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing & applying 2 component cold plastic paint rolled on surfacing material solvent free, skid resistant,material which has property of attaining 1.5-2.0 mm thickness in single coat application (Red) Including surface cleaning and cost of material etc. (All complete as per directions of engineer in charge).(All-inclusive on Bitumen & concrete surface) work shall carried out as per IRC:35-2015 (clause2.4).

CARRAIGE OF MATERIAL-Sand (38 KM.)

CARRAIGE OF MATERIAL-Stone Chips (37 KM.)

CARRAIGE OF MATERIAL-BRICKS (UPTO 10 KM LEAD)

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.3 Screened through sieve of I.S. designation 4.75 mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 90 cm dia, and 90 cm deep

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. - 36 Months

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3- 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hibiscus variegated of height 60-75 cm. with healthy variegated foliage in earthen pots size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Jatropha multifida (red colour) of height 60-75 cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge.

Providing and stacking of Nerium oleander (kaner) of height 60-75 cm. with 5-6 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (Chandni single) of height 75-90 cm. with 5-6 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma stans of height 90-105 cm. bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and displaying of Areca Palm having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Dracaena song of India specimen (three in one), having ht. 60 cm & above, well developed, fresh and healthy with good foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Raphes palm having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Acalypha twisted well developed with fresh & healthy 30 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Spider Lily (Hymenocallis littoralis) in polybags

Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing of Schefflera Green (three in one), mounted on moss stick 90 cm, well developed with full of fresh & healthy leaves from bottom to top with rich foliage in 25 cm size of Earthen pot/Plastic pot.as per direction of officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge

Providing and stacking of Foxtail palm of ht. 180-210 cm bottom girth 25- 30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Supply and planting of 3-meter-high Date Palm (Phoenix dactylifera), healthy and well-formed with a developed root ball, including transportation to site, pit preparation, planting, staking, and maintenance such as watering and fertilizing for 3 months; measured and paid per tree (each).

Providing and Displaying Bamboo Buddha vally variety with umbrella shape having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy as per direction of the officer-in-charge.

Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Albizia lebbeck (Siris) of height 150-165 cm in polybags

Providing and stacking of Azadirachta indica (Neem) of height 120-130 cm in polybags

Providing and stacking of Bauhinia purpurea (Purple Kachnar) of height 150-165 cm in polybags

Providing and stacking of Bombax ceiba (Silk Cotton) of height 150-165 cm in polybags

Providing and stacking of Cassia fistula (Amaltas) of height 120-135 cm in polybags

Providing and stacking of Delonix regia (Gulmohar) of height 4’-5’ in polybags

Providing and stacking of Mimusops elengi (Moulshari) of height 4’-5’ in polybags

Supply and planting of 3-meter-high Terminalia Mantaly (Madagascar Almond), healthy and well-branched with a developed root system, including transportation to site, pit preparation, planting, staking, and maintenance such as watering and fertilizing for 3 months; measured and paid per tree (each).

Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account. (a) Girth of tree shall be measured at a height of 1m above ground level. Girth of trees upto 50cm.

Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account. (a) Girth of tree shall be measured at a height of 1m above ground level. Girth of trees beyond 50cm and upto 90cm.

Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account. (a) Girth of tree shall be measured at a height of 1m above ground level. Girth of trees beyond 90cm and upto 150cm.

Hand painting directly on wall Concept Creation Creating design and creation of Artwork concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation

Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions.1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (1 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm, frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-chargePost Size 3000mm, Frame Size: 750mm x 250mm & 450mm x 450mm

Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following:Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (2 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm , frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge

Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following:Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (2 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm , frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge 900 mm (W) x 1200 mm (H) Approx (2400 mm post height)

Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (1 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm, frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge Post Height 1800mm, Frame Size: 450mm x 450mm

Agra Red stone jalli- Agra Red Sandstone Jali, smooth finish, H/Thick: Per SQF x 35 to 40 M/M/ Cm.

Agra Red stone Pillar- Agra Red Sandstone Pillar, smooth finish, H/Thick: 120" Inch, Diameter: 16" Inch, Weight: 329 Kg.

Stone Sculpture Articles 34 - Beige Sandstone Sculpture, smooth finish, H/Thick: 52" Inch, Weight: 1142 Kg.

Kandla Grey Stone Bollards - Kandla Grey Sandstone Bollards, smooth finish, W: 8" Inch, L: 8" Inch, H/Thick: 27" Inch.

Carved Stone Bench- Kandla Grey Sandstone Carved Bench, W: 60" Inch, L: 16" Inch, H/Thick: 18" Inch, Weight: 210 Kg.

Granite Ball Shape Stone Bollards- Rajasthan Black Granite Ball Shape Bollards, Honed Finish, Diameter: 16" Cm.

Autumn Brown stone monolith- Mandana Red Stone Monolith, natural finish, W: Free Size Cm.

Mandana Red stone Monilith- Autumn Brown Stone Monolith, natural finish, W: Free Size Cm.

U style Stone Bench- Teak Wood Sandstone bench, smoothl finish, width 72'' inch, length 18'' height 18''

CAST IRON BENCH Cast iron powder-coated garden bench with 3-seater capacity, designed with integrated seat and backrest for outdoor use. The side frames are made of robust cast iron, while the seat and backrest are fabricated from 14-gauge mild steel pipes, ensuring strength and durability. The bench features a decorative leg design, armrests, and backrest for enhanced comfort. Finished with weather-resistant powder coating suitable for long-term outdoor installation. Dimensions: total height 480 mm, seat height 350 mm, width 410 mm, total length 1225 mm. Load-bearing capacity up to 150 kg

CONCRETE BOLLARD- Providing and supplying 900 mm high precast concrete bollards of approved shape and size, made with M25 grade concrete, finished smooth, including reinforcement as required, with provisions for fixing or embedding into the ground, complete with transportation and installation at site as per the Engineer-in-Charge’s direction.

MS TREE GRATING- Providing and supplying factory-made Mild Steel (MS) tree grating, size 1200 mm x 1200 mm, fabricated from high-quality MS bars with suitable spacing to allow air and water passage to tree roots. The grating shall be thoroughly cleaned, treated with anti-corrosive primer, and finished with a durable powder coating to ensure resistance against weathering and rust. The MS tree grating shall be fixed on a concrete base with proper anchorage and leveling as per the Engineer-in-Charge’s instructions. Equivalent makes such as Pidilite, local approved manufacturers or as directed by the Engineer-in-Charge shall be used.

CONCRETE PLANTER - Providing and supplying factory-made precast concrete planter boxes of size 1200 mm x 1200 mm (or as specified), in approved shapes such as rectangular, square, circular, or geometric designs, by KK Manhole & Gratings Co. Pvt. Ltd. or equivalent approved manufacturer. The planter boxes shall be manufactured from M-30 grade reinforced concrete using vibro-compaction for enhanced strength and durability. They shall have adequate drainage provisions and smooth finished surfaces with options for plain grey, terrazzo, or pigmented colors as approved by the Engineer-in-Charge. Designed for outdoor urban landscaping and streetscape applications, the planters shall be weather-resistant and require minimal maintenance. Installation shall be carried out as per specifications and direction of the Engineer-in-Charge.

ARTISTIC SCULPTURE DEPICTING TRIBALS, FREEDOM FIGHTERS/LEADER, TRIBAL ART WITH SCULPTURE\ AND EXTERNAL CONCEPT Creation - 12 MTRX 2 MTRX 3 MTR Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork Execution:Execution of approved design in ss 316 grade steel / stone/casted alluminum pu colored antique as per approved finish (mrf/akzo nobel) and protected against discoloration by sealing it with top coat of Mrf/Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing & Staad file etc., to withstand high wind pressure. The sculpture will be free from any Undulation/Dent unless it is part of the design. The cost is inclusive of transport/packing and installation of the same at site. Fastener/screws hilti or equivalent company. Approved Make - East Craft Designs Pvt. Ltd., New Delhi/ Ram Sutar or equivalent artist with relevant experience

ARTISTIC SCULPTURE DEPICTING TRIBALS, FREEDOM FIGHTERS/LEADER, TRIBAL ART WITH SCULPTURE\ AND EXTERNAL CONCEPT Creation - 4 MTRX 3 MTRX 3 MTR Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork Execution:Execution of approved design in ss 316 grade steel / stone/casted alluminum pu colored antique as per approved finish (mrf/akzo nobel) and protected against discoloration by sealing it with top coat of Mrf/Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing & Staad file etc., to withstand high wind pressure. The sculpture will be free from any Undulation/Dent unless it is part of the design. The cost is inclusive of transport/packing and installation of the same at site. Fastener/screws hilti or equivalent company. Approved Make - East Craft Designs Pvt. Ltd., New Delhi / Ram Sutar or equivalent artist with relevant experience

WELCOME TO RANCHI JOHAR RANCHI - ARTISTIC SCULPTURE SIGNAGE DEPICTING TRIBAL ART AND LOCAL CULTURE WITH SCULPTURE AND EXTERNAL CONCEPT Creation - 3 MTRX 2 MTRX 2 MTR Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork Execution:Execution of approved design in ss 316 grade steel / stone/casted alluminum pu colored antique as per approved finish (mrf/akzo nobel) and protected against discoloration by sealing it with top coat of Mrf/Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing & Staad file etc., to withstand high wind pressure. The sculpture will be free from any Undulation/Dent unless it is part of the design. The cost is inclusive of transport/packing and installation of the same at site. Fastener/screws hilti or equivalent company. Approved Make - East Craft Designs Pvt. Ltd., New Delhi / Ram Sutar or equivalent artist with relevant experience

Hand painting directly on wall Concept Creation Creating design and creation of Artwork concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, display of actual size dummy /mockup Fabricated in sun board with digital print for client approval. ARWORK EXECUTION Towards the cost doing hand painting using artist quality colors by qualified artists all under the watchful eyes of expert artist

Design creation ,Providing and fixing artistic glass mosaic tile mural using premium quality imported/Indian glass mosaic tiles of approved brand (such as Sicis, Vidrepur, or equivalent), hand-cut and assembled as per detailed design/pattern approved by Engineer-in-Charge. The work shall include preparation of surface, supply and laying of mesh-backed mosaic tiles of size not more than 20x20 mm in approved shades and colours, adhesive bonding using polymer-modified tile adhesive, finishing with matching epoxy grout, cleaning and polishing, including necessary scaffolding, curing, protection till final handover, and disposal of debris – complete in all respects as per direction of Engineer-in-Charge. Note: Design/artwork shall be as per architectural intent and may involve abstract, cultural, or thematic visuals customized to the project. The contractor shall provide 3D visualization and mock-up for approval before full-scale execution

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (a) From 0.00 M to 50.00 M below G.L.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (b) From 51.0 M to125.00 M

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (c) From126.0 M to175.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

WATER FEATURE FOAM JET Supplying, Installing, Testing & Commissioning of Water Fountain System , As per the specifications : Jet nozzle 4 set of supremepools.submersible water proof light made out of Noryl / stretched stainless steel and cable gland suitable to be fitted with emitter type power with all in one symmetrical optical lens of 85% effeciency step tempered glass 8mm with protection class of IP-68 i/c connection & water proof jointing etc as required 4 set of supremepools,.Indoor type Cubical Control Panel made of 16 gauge CRC sheet powder coated with 4 Starter of supremepools, Single phase preventer, MCB, volt-meter, Amp meter, TP MCB's, for switching on and off pumps and lights, Protection circuits etc with reputed makes L& T, Schneider . ,Complete with relays 4nos, of supremepools.Step Down/Power Supply Transformer For the Light 8 nos of supremepools ,.Enclosure Box For the Light 4 sets,. SS Light Stand 1 sets,.Recirculation submersible pump to acheive the design flow with proper head and discharge 4 nos, of supremepools.Capital fitting in uPVC such as control valves NRV's etc. required for the final installations 4 job,.Supply, installation, testing & commissioning of uPVC pressure Pipes with plain socket suitable for solvent cement jointing conforming to IS:4985/2000 & fittings conforming to IS 7834/87 including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs including necessary 1 job,. Complete Electrical Work such as conduits, bends, fittings etc. of required sizes 1 job,.Wires of Various sizesincluding accessories like glands, stickers, sub tape etc for final equipment installation 1 job,. of supremepools Providing MEP Shop drawings For the WF with all nozzles in details 1 job,. Installing, Tasting & Commissioning of the Water Feature equipments 1 job

M/S AUM CONSTRUCTION (BID ID -684445)