PROPOSED CONSTRUCTION OF COMMUNITY CENTRE AT GETALSUD DAM. RANCHI, JHARKHAND

Amount

CIVIL WORK

Providing and fixing ALDSMSS304(300*16mm) ALDSMSS304(300*16mm) aldrop SS304 300*16mm with screw etc. complete :

Providing and fixing TS 1010SS 304 SS Sq shape tower bolt dia 10mm 10" in SS finish in SS304 grade with necessary screws etc. complete :

Providing and fixing 5mm SGG Planilux Clear Toughened. Glass , shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge .

Aluminum Glass Railing Providing, supplying & Installation of aluminum extruded powder coated profile with 12mm Clear Toughened glass with all necessary accessories like handrail, epdm gasket, anchor fasteners, screws & other fittings & fixtures all complete

Providing and fixing Shingles roof cladding over cement fibre sheet over existing MS rafter and purlin structure (MS structure costing to be taken separately)

Providing and fixing Vinyl false ceiling at all height of 10' x 1, as per approved shade, design and pattern suspended on GI channel

Reinforcement bar Protection Coating against Corrosion Surface Preparation: De-rust the steel using mechanical, circular wire brushes and with application of alkaline rust convertor, Sand blasting/shot blasting is the effective method of surface preparation prior to APCOREP RUSTCOAT RB application, where large quantities of rebar are to be coated.

Mix APCOREP RUSTCOAT RB Base and Curing Agent in the prescribed proportions by volume for five minutes thoroughly and allow it to remain in the container for five minutes. Apply using brush in two coats keeping an interval of minimum 6 hours between the coats which is of of Epoxy /Phenolic Base with Mix Proporation by volume 1 : 1, with Yellow appearance.

RCC Protection Coating against Corrosion Surface Preparation: Thoroughly clean the substrate to remove the dust, harderned cement slurry, Oily residues etc. by scrubbing with coarse wire brushes/grinding/chipping off the top layer/sweep blasting methods depending on site requirements. Ensure residual amounts of demoulding agents, curing agents, inhibitor residues are thoroughly removed.

Prior to SMARTCARE APCOREP Kcretecoat application, seal all the cracks, crevices, joint etc. with EPCO-1010®/ PC Sealant. Mix SMARTCARE APCOREP Kcretecoat base & curing agent in prescribed proportion by volume and allow it to remain for 10 minutes. Apply minimum TWO COATS of SMARTCARE APCOREP Kcretecoat on the surface keeping minimum 24 hours time interval between them. Smoking, naked flame or light should not be allowed during application or in the area of storage. which properties of Salt Spray (ASTM-B 117) 2000 Hours and Resistance to sea water (Carried out upto 6 months) Coating Resistance (Carried out upto 6 months) 109 Ω, Adhesion (ASTM-D 4541) 4.5 N/sq mm, Impact (ASTM G 14–04) 45 cm, Flexibility (ASTM D-522) 1/8”.

Provide drilling 20 mm dia., rebaring 25mm with depth 250 mm with HILTI RE 500 V4 Chemical with all machine tools tackles & Labour completed.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Wash basin size 420X420X150 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing CP Brass 32mm size bottle trap with 300 mm & 190 mm Long Wall connection Pipes and Wall Flanges of approved quality & make and as per the direction of engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing white vitreous wall mounting water closet with Uf Soft Close Slim seat cover hinges of size 345X495X365 mm of approved shape including providing & fixing white vitreous concealed cistern with dual flush fitting, of, including seat cover, flush plate and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Wash basin size 420X420X150 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing CP Brass 32mm size bottle trap with 300 mm & 190 mm Long Wall connection Pipes and Wall Flanges of approved quality & make and as per the direction of engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass Overhead Shower 240X240MM Square Shape Single Flow (Body & face plate stainless Steel With chrome finish) With Rubit Cleaning system including Shower arm 600X25X25 MM Square Shape for Wall mounted Showers with Flange of approved quality & Make.

Providing and fixing Shower mixture of approved quality including Wall mixer with provision for overhead shower with 115mm long bend pipe on upper side connecting legs & wall flanges :

Providing and fixing 8mm dia Health Faucet with flexible tube upto 1meter long with S.S. Triangular plate to european type W.C. Of approved quality and make as approved by engineer in charge.

Providing and fixing C.P. brass Two Way bib cock of approved quality conforming to IS:8931 : Of approved quality and make as approved by engineer in charge.

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I. Floor trap - 100mm dia.

Ring rubber

Door piece

Providing, fixing & testing uPVC SWR pipes confirming to IS 13592 (Type B) alongwith all required fittings like tees, bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the floors and walls where required complete of outer diameter. 110 mm dia Pipes

40 mm dia Pipes

50 mm dia Pipes

63 mm dia Pipes

Providing and Fixing 110x110 mm uPVC 'P' trap with Height riser/Saddle as required size ftting with seal 50 mm of self cleansing design floor/urinal trap without vent suspended with supporting clamp or in sunken portion including cutting and making good the walls and floors wherever required complete in all respects. 110 mm inlet & 110 mm outlet Long ht

Providing and Fixing uPVC floor drain of following size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects. 110 x63mm outlet

Providing and fixing 1 mm thick stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete. 125mm dia.

Providing & fixing uPVC Floor clean out plug with suitable insert keys for opening in: brass cap, male threaded joint with threaded uPVC socket fixed to uPVC pipe joints as required complete in all respects. 110mm dia.

Providing & fixing in position 25 mm dia lawn hydrants consisting of 25 mm dia Ball valve, GI nipple and threaded hose receiver complete as required.

Providing, fixing, commissioing, testing and of open well submersible pump for each pump IP 58 protected electric enclosure comprising of 2 Nos. Electrical Driven Horizontal pumps with all accessories coupled to motor suitable for operation on 200-240 volts, 1 phase 2900 RPM. motor with SS 304 body all accessories such as NRVs, valves, common delivery header complete in all repsects. No. of Pumps: 2 (1 Working + 1 Stand by ) Capacity : 60 LPM

FOR GARDEN IRRIGATION PUMP No. of Pumps: 2 (1 Working + 1 Stand by ) Capacity: 100 LPM

Supply, installation, testing and commissioning of Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect Capacity- 100 lpm (Each)

Providing, fixing, connecting & testing of Blanking plate (6XRJ45 Blanking plate for 19" panel - Black).

Providing, fixing, fitting, connecting and testing of Splice Tray - 24 Fiber Capacity.

Fiber Patch Cord:- SITC of SC/SC or SC LC Duplex 2 Mtr MM Fiber Patch Chord as per requirement.

10/100/1000 MM SFP Module:- Providing, fixing, connecting & testing of Gigabit Fiber Module-MM, Support up to 550mtr

Providing, Laying, connecting and testing of 6 Core un Armoured unitube Multi Mode OM3 OFC (Fiber Optics cable 6 F) for indoor connectivity in existing PVC conduit, (Indoor Connectivity,)

Providing, Laying, connecting and testing of 6 Core Armoured unitube Multi Mode OM3 OFC (Fiber Optics cable 6 F) for Outdoor connectivity Armored fiber Optic Cable shall be used. Optical fiber cable shall be laid underground in 25/32 mm HDPE pipes with suitable Manholes at every 40 mtrs. for easy pulling and proper Maintenance. (Cost of civil part is also added) (Out Door Connectivity)

Supply, fitting, fixing and testing of UTM/Router with LAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo, WAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo , HA: 2 x 10/100/1000T RJ-45, Should support URL Filtering, DoS and DDoS attack detection and protection, Antivirus, Malware protection, Static, Dynamic (BGP4, OSPF, RIPv1/v2), source-based routing, policy-based routing and IGMPv1/v2/v3. Warranty 5 year from Day 1 ( Cisco - ASA 5516-X with Fire Power Services / Allied Telesis - Model No. ASA 5516-X with Fire Power Services/AT-AR3050S/SRX300 / Juniper - SRX300) Cost of Router / UTM

8 port managed Network PoE Switch: - SITC of 8 port managed Network PoE Switch: 8 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports.

Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS boxes for MATV system and shall be suitable for interactive system. Make:- (Reputed of as directed by I/E or Consultant) Two Way (S-2) (Make:- Reputed of as directed by I/E or Consultant)

Two Way Tap off (T-2) (Make:- Reputed of as directed by I/E or Consultant)

Supply, fitting, fixing and testing of Auto-manual Voltage Stabilizer with High Voltage cut off 0.25 KV 220V Range- 100 to 280V Single Phase 50 Hz Stabilizer along with cord & plug. Make:- Sen & Pandit, V Guard, Neutronix.

SITC OF IP Setup Box suitable for oparation on single phase, 220V for TV. (Reputed of as directed by I/E or Consultant)

Supply, fitting, fixing, installation & testing of 400mm 80-Watt Pedestal Fan with Remote with 68.6 x 33 x 47 Centimeters dimention 5 kg weight WITH 1 Year warrenty . etc. as required. Make:- USHA/Venus / Bajaj / Havells

Supply , fitting fixing and commissioning of UV BASED WATER PURIFIER CUM COOLER Model: AG Green Pure Chill Storage 80 SS UV Aquaguard Storage Water Cooler Cum Purifier Water Storage Capacity: 80 ltrs. Two Faucets . Make:- (Eureka Forbes Ltd/Voltas/ Kent. STORAGE COOLER CUM PURIFIER (PURE CHILL 80 SS UV) APROXIMATE EXTERNAL DIMENSIONS (W X D X H) 640 X450 X1350 Cost of UV BASED WATER PURIFIER CUM COOLER

Supplying, fitting, fixing, connecting and testing of decorative up-down light Fixtures in die cast aluminium finish with 2x8 Watt LED lamp directly on wall including connection with 1.5 sq mm FR PVC insulated copper conductor cable and eathing the body etc. as required (IP-54 Protection) Make:- Jaquar-Up down light- BRIGHTEX , Philips, Bajaj, Havells,Wipro.

Supplying, fitting, fixing, connecting and testing of decorative pendent suspention light Fixtures in brass finish in glass diffuser with G4 LED 5WX1 lamp Dia : 200 mm

SITC of Step light (warm Light) Robust design LED 10x0.5W step-light with driver and dally control IP66/IK10, easy to install, maintain and comes with suitable mounting box, energy saving step light grey clour packed with die cust aluminium finished with features applications (3000/4000K) with IP-65 protection . for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. Make:-Jaquar-Step light- Alfie, Philips, Havells, Bajaj, Wipro, K- LITE.

WALL BRACKET LIGHT Supplying, fitting, fixing, connecting and testing of decorative Wall Bracket Fixtures Lamp : G9 LED 5WX1 in GOLD finish in glass diffuser with Width : 215 mm Fixture Height : 350 mm, Description : 1 Light clear glass with brushed brass wall lamp directly on wall including connection with 1.5 sq mm FR PVC insulated copper conductor cable and eathing the body etc. as required (single Holder) Make:-Jaquar, Philips, Bajaj, Havells,Wipro.

Supplying, fixing, testing and commissioning of Inverter type Ductable split air- conditioning unit suitable to operate from 415+10% volt, 50 Hz, 3 phase power supply, with electronic expansion valve, air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with hermetically sealed scroll compressor (with R- 410a) including first charges of gas, condenser coil, propeller fans controls, inter connection control panel Corded Remote. (MAKE: Carrier,Haier,Voltas,Toshiba) 5.5TR Inverter ductable unit

Supply, installation, balancing and commissioning of site fabricated GSS/GP sheet rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc as per approved drawings and specifications.

Supply and fixing of acoustic lining of supply air duct with 9 mm thick nitrile insulation as required as per specifications.

Supply and fixing of acoustic lining of supply air duct with 12mm thick glasswool Rigid Board with aluminium perforated sheet as required as per specifications.

Supply, fixing, testing & commissioning of supply air diffusers/grilles of powder coated aluminium with aluminium volume control dampers as per specifications.

Refrigerent piping with cable Supply, Installation, Testing & Commissioning including pressure testing of copper refrigerant piping complete with all copper fittings for the DSU units along with 19 mm thick closed cell elastomeric nitrile rubber insulation in tubing form as required.

Providing & fixing of uPVC Pipe complete with fittings, supports as per specifications and duly insulated with 9 mm thick pipe section of closed cell nitrile rubber.

Electrical and control cable Supply, fitting, fixing and commissioning of following size of control cum poer copper cable wiring in medium duty PVC Conduit between indoor and outdoor units.

Supply, installation, fixing, fitting, testing and commissioning, of Advance New Generation Early Streamer Emission technology Lightning Arrester of Type DMSGI-45 with Level-1 protection of 90 Mtr. Radius. Device is confirming to standard NF C 17-102.Device shall be mounted at least 5 meter clear to highest point by support-mast of 40 mm dia GI Pipe duly galvanized with minimum 85 micron zinc coating with foundation to suit Mast, for Level 1 protection of 90 m (as per NFC 17-102 & IEC 60-1:1989.) radius with accessories complete as required for all other structures and designated open spaces covered by general area lighting mast on which ESE (Early Streamer Emission) can be installed similar to OPR 30 with active system. The Insulation material used to electrically isolate the panels shall be comprised of a base polymer which provides high Ozone & UV resistance with di-electric strenght of 24-38 KV/mm tested as per NFC 17-102 & IEC 60-1:1989. The ESE terminal shall not contain any electronic circuits or any moving parts for its operation. The ESE terminal shall be tested & certified by CPRI (Central Power Research Institute, Govt of India) for the Impulse current of 45 KA (8/20 micro sec) with 5 positive & 5 negative impulse. The ESE (Early Streamer Emission) terminal shall be approved by DGMS (Director General of Mines Safety), Govt of India. Make:- OBO/ BAKIRAL/ LPN./ ALFAl/ Altec Corporation Total cost of Advanced New Generation ESE Air Terminal Lightning Conductor

Tripod Earthing System for ESE (Early Streamer Emission) technology Lightning Conductor- (3 Nos. for per set):( Special Type Earthing on Natka Pahaad) Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for Tripod chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Total Cost for Tripod Earthing System for ESE technology Lightning Conductor- (1 Set = 3 Nos. Chemical Earthing as tripod Earthing for ESE Lightning Arrester

Total cost of Foundation and Plinth construction for Bollard light with all above accessories.

Supply, installation, testing and commisning of 8W LED solution lighting family for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. (IP-65- OUT DOOR APPLICATION). (2 yrs Warranty, 50,000 burnung hrs,) Cost of 8W LED Garden spike Light

SITC of 8W LED Bollard light Garden bollard Light with , Good protection against water and dust ingress and impact, with all accessories. (2 Yrs Warranty, 50,000 burnung hrs,) (IP-65 Outdoor application)

SITC of 5 mtr set LED Cove linea Plus (STRIP) (warm Light) LED 25 W tape 5 mtr in Length with driver (blue or Yellow in colour) easy to install, maintain and comes with suitable driver energy saving strip tape light (3000/4000 ) base & Lamp . for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. (2 Yrs Warranty and 50,000 burnung hrs,) (Outdoor application)

Supplying, fitting, fixing, connecting and testing of driver for strip light with IP-20 protection Make:-Jaquar , Philips, Bajaj, Havells,Wipro.

Supplying, fitting, fixing, connecting and testing of decorative up-down light Fixtures in die cast aluminium finish with 2x8 Watt LED lamp directly on wall including connection with 1.5 sq mm FR PVC insulated copper conductor cable and eathing the body etc. as required (IP-54 Protection) Make:- Jaquar-Up down light- BRIGHTEX , Philips, Bajaj, Havells,Wipro.

SITC of Step light (warm Light) Robust design LED 10x0.5W step-light with driver and dally control IP66/IK10, easy to install, maintain and comes with suitable mounting box, energy saving step light grey clour packed with die cust aluminium finished with features applications (3000/4000K) with IP-65 protection . for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. Make:-Jaquar-Step light- Alfie, Philips, Havells, Bajaj, Wipro, K- LITE.

Supplying, fitting, fixing, connecting and testing of decorative Inground burial light Fixtures in nchrome finish with 10Watt LED lamp with ip-67 protection with round shape etc. as required (OUTDOOR APPLICATION) Make:- Jaquar-Inground Burial- POLARIS, Philips, Bajaj, Havells,Wipro.

Supplying, fitting, fixing, connecting and testing of decorative pendent suspention light Fixtures in brass finish in glass diffuser with G4 LED 5WX1 lamp Dia : 200 mm Fixture Height : 420 mm, Description : 1 Light clear glass with brass finish pendant directly in ceiling including connection with 1.5 sq mm FR PVC insulated copper conductor cable and eathing the body etc. as required .

Supplying, installation, shifting to location, testing and commissioning of a continuous rating of 100 KVA, 3Ph, 50Cy, 11/0.433KV, Off Circuit, (OCTC) oil cooled, copper wound, (-12.5% to +2.5% in step of 2.5 %) Outdoor Transformer as per IS 1180 (Level-1) at full load and temp. rise not exceeding 45 degree C, by Thermometer in oil and 50 Degree C. by the resistance in winding after continuous run in full load rating. The Transformer should oil immersed winding having Vector DY-11 HT side connected in Delta, & LT Side connected in Star with neutral brought out connected to provide separate earthing. In Transformer HT Side Cable End Box, & LT side - Cable End Box. Transformer shall be latest manufacturing standards as per amended IS Specifications and load and no load losses shall be limited to the values given below as per IS or Norms issued by JVVNL or which ever is lower. The transformer, length of MS channels as per the norms of 100 KVA Outdoor Transformer with all accessories, air filled cable box and accessories as per General Specifications of 100 KVA out Door Transformer and should have suitable for 11KV 1 Run, 3 Core 50 Sq mm XLPE Al. Ar. Cable and LV termination box shall have suitable arrangement for 1.1 KV, 1 Run, 3.5 Core, 300 Sq. mm XLPE Al. Ar. Cable etc as required. The copper loss and Iron loss shall be as per the Level 1 rating out Door Transformer. The Transformer shall have all standard Protection, standard accessories etc and shall have 3 Years warranty against any manufacturing defect from the date of delivery under normal operating conditions and proper use (Make:- Power Star/True Volt/ Synergy, Arnav Power Tech.)

Cost of 3 Core 50 Sq. mm. XLPE PVC Al. / Ar. Cable 11 KV HT CABLE

PTZ outdoor cameras: - SITC of true IP day night viewing PTZ cameras proposed are 2MP IR Outdoor PTZ Camera-1 /2.8’’ progressive Scan CMOS, 1920 x 1080 at 60fps,4.8mm to 153mm, 32x Optical, 16x digital zoom , Color: 0.005 Lux at F1.6 B/W: 0.001 Lux F1.6 ICR, ONVIF, support H.265, MJPEG, 120 db WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Triple individually configurable stream, 24 VAC & Hi PoE, IR range: 150m, pan: 360° endless, Tilt: From-15° to +90° (auto-Flip), Pan Speed- from 0.1°/s to 160°/ s, Preset Speed: 240° /s, Tilt Speed- From 0.1°/s to 120°/s, Preset Speed 200°/s, presets- 300, Alarm Input- 2-ch alarm input, Alarm output-1ch alarm output, Audio-1, channel input & Output, Support on- board storage up to 256 GB (SD card not included), IP66, Ik10, Face Detection, Intrusion Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, UL, CE, FCC Certified

SITC of Industrial grade 4-Port PoE Gigabit Media Switch for fiber to PoE conversion. IEEE 802.3af/IEEE 802.3at PoE+ standard compliance, Supports a maximum of 30 watts of output power, 10/100/1000BASE-T Ethernet TP interface, Auto-negotiation, auto MDI/MDI-X with PoE injector function, Approved Make: As approved by consultant.

SITC of 1G SFP Module - LC Type with necessary Patch cord/ Pigtail to connect incoming line.

SITC of Swaged pole of Overall Length 9 Mtr, Planting Depth- 1.5 Mtr, Height Above Ground- 7.5 Mtr, Bottom (H3)-5 Mtr, (H2) -2 Mtr, Top (H1) -2 Mtr, Bottom (MM)-114.3 x4.50, Middle(MM) -88.9 x4.05, Top (MM)-76.1 x3.25 with approx weight not less than 92Kg. for PTZ Camera

SITC of 4-Axis Joystick Network keyboard Controller for PTZ Camera

SITC of outdoor fiber distribution unit including 2-Nos. 6Amp. power socket & 1-No. switch with 1-pole MCB, must have capacity to accommodate fiber distribution items and PoE switch, convertor, Media convertor etc. Must have option to Pole and wall mount facility. Must be of industrial grade and fully weather proof IP65 rating. Sould be supplied with all necessary pigtails, patch cords, cables, connectors etc. to connect all outdoor cameras and network equipments. Approved Make : Custom or as approved by consultant.

Providing, Laying, connecting and testing of 6 Core Armoured unitube Multi Mode OM3 OFC (Fiber Optics cable 6 F) for Outdoor connectivity Armored fiber Optic Cable shall be used. Optical fiber cable shall be laid underground in 25/32 mm HDPE pipes with suitable Manholes at every 40 mtrs. for easy pulling and proper Maintenance. (Cost of civil part is also added) (Out Door Connectivity) Make:- Legrand, Opterinix, Molex, Benden

Supplying, designing, manufacturing, installation, shifting to location, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing feeders of Floor Mount LT Panel, fabricated out of 2 mm thick (14SWG) CRCA sheet steel, dust and vermin proof with reinforcement of suitable size iron channel, size 50mmx50mm x6mm (or ISMB CHANNEL) with proper lifting arrangement, (IP-42) fully compartmentalized cubical type (folded joints construction), totally enclosed LT Panel and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 36 KA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection & meters as required. INCOMER :- Provision of Mechnical interlocking between 250 A/FP/25KA MCCB as common incoming and 1 No. of 250 A TPN on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time. 1 No.250 A F/P MCCB (25kA) with adjustable thermomagnetic release type with S/C & O/L protection, With ON-OFF- Indication and front extended rotary Handle and spreader links in both end (Incoming cable size –1 Run 120 Sq mm 3.5 Core Al. Ar. Cable). 1 no. 250 A/TPN on load open executiuon type panel mounted TRPN 415V Change over with handle. (FOR 82.5 KVA DG SET) Make:- L& T, Legrand, Socomo. Out Going Feeders 2 No. 125 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle with spreader links. Cable Size 3.5 C 70 Sq.mm Al,Azr, Cable) (1no. For APFC Panel & 1 no. as spare)2 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle with spreader links. (1 nos. for out door Feeder Pillar for external lighting & 1 no. ss spare. 9 Nos. 40 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle with spreader links. (3 nos. for TPN DB Restuarant & kitchen , 4 nos. for ductable AC & 2 no. ss spare. 5 nos. 32 A DP MCB C Seires 10kA(1 nos. for staff RM., 1 no for Panel RM., 1 no for gate & 2 nos. as spare) Total Cost of Comonents & Switch Gears of Main LT Panel

Supply, manufacturing and effecting proper connection of all incomer and outgoing, unloading at site, shifting tolocation, fitting, fixing and testing of the of out door canopy type double door Feeder Pillar fabricated out 2 mm (14 SWG) CRCA Sheet steel dust, damp, vermin and water proof (IP-55) free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted (powder coated) complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Iron Angle for grouting in outer area. INCOMER :- 1 No.63A F/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L protection, and front extended rotary Handle and spreader links in both end. OUT- GOING 4 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, on of trip and S/C , O/L protection, with Rotary Handle & Spreader links. (1 no. as spare) 3 nos. Power Contactor 40A NO NC of three phase of suitable rating. 3 nos. Astronomical Alpha Rex³ single channel Timer 24 hrs. 3 nos. Four pole two way Lexic changeover with centre off 440V AC 40A to be used in case of timer failure to by pass the timer. 2 nos. 63A DP MCB C Series of 10 kA 2 nos. 32A DP MCB C Series of 10 kA

Supplying & Laying 12mm thick chequered rubber matting of 1.1.kv 1x1 m (L & wide) of tested quality to with stand 15KV dielectric strenght of approved make as per IS-5424-1969.

Supplying of fire buckets of 10 liters Capacity of approved quality, painted white from inside and red outside and having inscription "FIRE" in white conforming to I.S. 2546/1974 duly amended upto date complete as required & approved by Engineer Incharge.

Supplying and fixing of MS pedestal stand heavy duty with rain protection cover as required suitable for supporting three fire buckets as required for fire fighting system & approved by Engineer Incharge.

Supplying and fixing carbon dioxide (CO2) type fire extinguishers conforming to IS 15683 with cylinder duly charged of capacity 4.5kgs. including fixing clamps, brackets, bolts and nuts etc. as required & approved by the Engineer Incharge.

Supplying and fixing 10kg capacity Modular Automatic Fire Extinguishers dry chemical powder nitrogen type pre-set at works ranging from 57 deg C/ 68 deg C/ 79 deg C fire extinguishers conforming to IS 15683 including fixing clamps, brackets, bolts and nuts etc. complete as required & approved by the Engineer Incharge.

Supply and fixing of shock treatment/ restoration charts written in Hindi/ local language and English duly framed and covered with 3.0 mm glass as required.

Supply of First Aid Box made of 16 SWG MS Sheet duly painted within inside and outside surfaces with one coat of primer and two coats of synthetic paint of required shade comprising the following minimum but not limited, minimum 1 No. band aid bandage 150mm, 1 No. Savlon Soap 30 ml, 1 No bottle Betadine 30 ml, 1 No Packet dressing material etc. as required, approved by Indian Red Cross / St. John's conforming to IS:2217.

Supply of 440V grade Rubber Hands Gloves. As per IS:4770- 1991.

Supply of 1 pair 12 KV rubber hand gloves of approved make, as per IS:4770- 1991.

Supply and fixing position the approved single line diagram framed in 1000 x 800 mm size glass frame and installed in main switch room.

Providing, fitting, fixing, fabricating, erecting of MS angle of section 50 mm x 50 mm x 6 mm size for Brick wall trench to make support for MS iron plate to be fixed on every after 300 mm in RCC trench.

Providing, fitting, fixing, fabricating, erecting of MS Plate of 2'X2 (12 mm) thick' for covering Brick wall cable trench in panel room on the support of iron angle each piece of MS plate shall be 450 mm (D) x 450 mm (W). (To cover the Brick wall cable trench in panel room.)

SS Gas & Char-Coal Tan-Door Size: 32”x32”x36”

SS Tan-Door Side Table with 2 B/S Size: 32”x18”x3

SS Single Unit Wash Sink Size: 24”x24”x34”+4

SS 2 Burner Indian Cooking Range Size: 45”x24”x34”

SS Spices Side Table with 2 B/S Size: 30”x16”x34”

SS 2+1 Chinese Cooking Range Size: 54”x30”x32”+12”

SS Chinese Side Table with 2 B/S Size: 30”x16”x34”

Double Deep Fat Fryer

SS Pick-up Table with 2 B/S Size: 45”x26”x34”

SS 3 Door Work-top Refrigerator Size: 72”x26”x34”

SS Dosa Hot Plate Size: 36”x24”x34”

SS Dosa Preparation Table with 2 B/S Size: 24”x24”x34

SS Single Unit Wash Sink Size: 18”x24”x34”+4”

SS Pick-up Table with 2 B/S Size: 45”x24”x34

SS Heavy Duty Single Burner Cooking Range Size: 24”x24”x24

Idly Streamer Size: 20”x20”x24” Capacity: 54 Pcs

Single Deck Pizza Oven

SS Salamander Size: 30”x19”x19”

SS 3 Door Work-top Refrigerator For Pantry Section Size: 72”x26”x34

SS Working Table with 2 B/S Size: 45”x24”x34”

SS Single Unit Wash Sink Size: 24”x24”x34”+4”

Sandwich Griller (Single Unit) Size: Standard

VC Cooler Size: 450 Ltr

SS 3 Unit Wash Sink Size: 66”x24”x34”+4”

SS Soiled Dish Landing Table with Garbage Chute Size: 36”x24”x34”+4”

SS Clean Dish Rack 4 Shelve Size: 45”x16”x60''

SS Clean Pot Rack 4 Shelve Size: 48”x24”x60”

SS Wet Grinder Size: 5 Kg Capacity, (Electrical)

SS 4 Door Deep Freezer Size: 54”x28”x84”

SS Storage Rack 4 Shelve Size: 36”x18”x60”

SS Storage Rack 4 Shelve Size: 45”x18”x60”

(G.I) Hood with SS Oil Baffle Filter For Main Kitchen Size: 22’ Rft

(G.I) Ducting for Hot Air System For Main Kitchen Size: 80’ Rft (Approx)

5 HP Box Type Sound Proof Centrifugal Blower Fan for Hot Air System, Size: 5 Hp, 3 Phase, 440 Volts, 1440 Rpm.

5 HP Centrifugal Blower Fan Complete Installation

(G.I) Ducting for Fresh Air System Size: 70’ Rft (Approx

1 Hp Axial Flow Fan For Fresh Air Size: 1Hp,960 Rpm

1 Hp Axial Flow Fan Complete Installation

Fresh Air Grill Size: 12”x8”

6 Cylinder Manifold, M.S LPG Pipe Line 70’ Feet (Approx) , 08 Nos Burner Connection ,Others Fittings 2 Nos Ball Valve, Gage Meter 1 Pcs, Pressure Gage 1 Pcs total Complete Fittings

Steam beech wood , premium Leatherette Colour & Colour Family Red - Burgundy DINING CHAIR

Colour & Colour Family Brown- Dark Oak Dimension (W)1430mm X (D)890mm X (H)755mm DINING TABLE 4 SEATER

Dimension (W)1890mm X (D)970mm X (H)755mm DINING TABLE 6 SEATER

Dimension (W)640mm X (D)670mm X (H)1100mm LOW CHAIR MESH CHAIR

Supplying and placing of Storage,Helios/a/800-1800 office shutter Office shutter size : 800mm(l)x 1800mm(h). STORAGE

SINGLE BED Supplying and placing of Single Bed with out Mattress,Modern design single bed,Sku : ALLEN,single bed,Size : 1981 mm(l) x 977 mm(d) x 440 mm(h)

Supplying and placing of Steel Almirah,Metal storage of size 900mm(l)x 450mm(d)x 1980mm(h) STEEL ALMIRAH

MULTI PLAY STATION Wide range of multiplay systems and multi play station with various combination of slides, swings, crawling tunnel, climber, suspended bridge etc. The gigantic structure aesthetically designed for catering a huge number of children at a time with maximum. Color: multi color Location Type: Outdoor

MERRY GO ROUND Capacity:04 children; Rec. Age: 4 - 12 yrs; Area:1.2 m diameter; Height:0.9 m; Seat:2 mm thick frp; Bearing:heavy duty ball bearing

SEA-SAW length- 2000mm height-500mm Durable double steel frame soft easy grip handles and comfortable molded plastic seats

SWING length- 2000mm height-450mm

SCULPTURE SEAT Pebble seat, Polished solid concrete oval sculptural Seats in a range of sizes. material : Polished Cornish granite aggregate Concrete colour - white/ light grey finish - smooth

PEBBLES 50-60 dia, black marble ball pebbles, (rates including GST, Transport cost & Loading-unloading charges)

FRP POT (2"X1"X1")

Providing and stacking of Nerium oleander (korobi) of height 4 ft.

Providing and stacking of Tabernaemontana coronaria (tagor) of height 1 ft.

Providing and stacking of Tecoma Gaudichoudi(yellow bells) of height 4 ft.

Providing and displaying of Areca Palm having ht. 5 ft.

Providing and displaying of Gardenia Jasminoids(gandharaj) having ht. 1.5-2 ft.

Providing and displaying of Raphis Excelsa having ht. 2-3 ft.

Providing and stacking of Pandanus variegated having ht. 8 inch.

Providing and stacking of Heliconia humilis having ht.1 ft.

Providing and stacking of Xanadu having ht. 1ft.

Providing and stacking of Ixora singaporensis(rangan) having ht.1.5 ft.

Providing and stacking of Delonix regia of height 8-10 ft. in big poly bags of size 18"-21" dia.

Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Lagerstroemia speciosa(jarul) of height 8-10 ft. in big poly bags of size 18"-21" dia.

Providing and stacking of Spathodea campanulata of height 8-10 ft. in big poly bags of size 18"-21" dia.

Providing and stacking of Saraca asoca of height 8-10 ft. in big poly bags of size 18"-21" dia.

Supplying and pasting of WPC on cement fibre board, Width: 150mm, Thickness: 8 mm, Color:wooden, Usage - cicular platform.

Cement fibre board- supply and screwing of cement fibre board on the ms frame of the seating area,size-2400x1200mm,18mm thk.

Geotextile-Providing and laying 200gsm geotextile made of 100% virgin polypropylene non woven and mechanically strengthened by needle punchinm Elongation 55% g processand thermo fusion.The geotextile should have punture resistance 2.57 KN. Tensile strength15.6 KN/m, Elongation 55%, Permeability 34x10-3 m/s. The Geotextile to be overlapped by 200mm at joints over the drainage layer complete. ( make overlite Industries)

Providing and laying Grey Concrete RCC Grass Paver, for Landscaping, laying over 60mm thick compacted Sand bed- Size: 400 X 300 X 60 mm), Color: Grey, Usage/Application: Car parking area, Shape: Zig-Zag, Thickness: 60 MM

MULTI MEDIA SCULPTURE PLACED AT THE ENTRANCE OF THE LANDSCAPED AREA FIXEDON AN RCC BASE AND ILLUMINATED WTH 2 SPOT LIGHTS,ht-1.8m

Supplying,fitting and fixing M.S. grill gate with M.S. grills made of 20xGmm M S. flats or 16mm. M.S. square bars fitted on25x25x 6mm. M.S. Angle frame, spray painted with PU Paint.

Providing and fixing jaali wall as per drawing, using powder coated aluminium extruded built up standard tubular sections of required thickness

Providing and fixing at location a signs M.S internal hollow tube structure using Cosign Make- Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns) International standards, with Lifetime warranty under normal working conditions. Sign is including all extruded aluminium profiles profiles including i) 4 base profiles mill finished glossy appearance or texture, base profile with slots to accomodate 50x 50 mm , 100x50 mm or 150x 50 mm,(to create max depth of 200 mm from either of the combination aftet mounting base & cover profiles, M.S structure & 'V' notch groove to guide self tapering screws,directly to be screwed with ,Internal M.S structure with help of stainless steel high tensile strength zinc coated self tapering CSK screws (length as per requirement) ii) 4 cover profiles of eliiptical shape premium anodised with intel- locating faciltiy with base profile for posiotioning. to be screwed with base profile (screws not visible from outside) after cover profile is mounted to base iii) Top & bottom ACP egde profile premium grade anodised to cover edges of ACP free mounting without drilling or screwing. iv) ACP connect profile with minimum display free mounting without lockuing & drilling. etc ,Ultra violet print on ACP or ACRYLIC sheet can be done. Also, arrangement is done to (ACP or Acrylic 3 mm thick can be Inserted in Cosign totem profile slots). Top hat asper profile shape (aluminium 2-3 mm thick) is used to cover top part, 2mm thick opaque white acrylic(or clear)can be pasted on text panels as numbers with help of 3M make adhesive.also LED (Back lite) modules or edge lite modules. CosignTotem profiles screwed fixed with internal M.S structure are installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing and fixing at location a signs made up of Cosign India Pvt Ltd make I sign -display signage with 100 mm depth Aluminium extrusion Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15- 20 microns) Flatness & Twist of profile within 1.5 mm / meter length, with Lifetime warranty under normal working conditions. Media accomodation depth of 8 mm avialble for pasting on dual lock or strong two way adhesive. M.S fabrication slot of 65 mm depth for internal M.S structure.Media upto 6 mm thickness can be pasted or mounted with help of dual lock tape .assembled totem can be edge lite with help of edge lite modules or back lite with help of back lite modules.CosignTotem profiles screwed fixed with internal M.S structure are installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing a signs made as using Cosign india make .Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with Lifetime warranty under normal working conditions.Sign is single sided with aluminium profile click fitted on 2 plastic moulded endcaps.Sign is including all plastic injection moulded end caps black in shade which are directly press fitted ,media (vinly) warapping by virtue of design of profiles.Cosign make MPI panels fitted and installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing a signs made as using Cosign india make .Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet)with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with Lifetime warranty under normal working conditions.Sign is single sided with aluminium profile click fitted on 2 plastic moulded endcaps.Sign is including all plastic injection moulded end caps black in shade which are directly press fitted ,media (vinly) warapping by virtue of design of profiles.Cosign make MPI panels fitted and installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing a sign made up of Cosign make Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns) silver anodised shade as per Internationalstandards, with Lifetime warranty under normal working conditions. Frame consisting of media accommodation depth of 15 mm with overall depth of profile of 50 mm approx.Media of 4 mm thickness MDF with 4 mm thickness Non-reflective Clear glass. Frame consisting of ART springs to hold media firmely on profile slots. Installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPa typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with Lifetime warranty under normal working conditions. Sign flip profiles with 32 mm visible border.Sign has high quality plastic moulded base with slightly flexible in nature, with wall mountiing screw position hidden beneath the flip profiles. and installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing ready sign & fixing at location a Cosign make emergency exit sign- illuminated, surface mount (wall or ceiling) Dual sided made up of plastic material , battery backup of 3 hours (180 mins) .Battery life of 300 cycles of charge & discharge Li- ion battery 3.7 Volt, 100 mA, Charge time of 24 hours. Input voltage 220-240 Volt A.C, 50/60 Hz. Viewing distance 30 meter, degree of protection IP20 (rating for protection against solid object upto 12 mm) white light colour full back (white colour) LED illumination with green white coloured graphic inserted on both sides on 0.4 mm PC (sizes, texts, symbols or graphics as per standard safety norms & regulations) graphic options of -left ,right, up staircase down staircase. Test facilty button self test plus auto self test, opreration in maintained and non maintained mode (power saver mode).Sign with 12 months warranty for electric circuit & 6 months warranty for battery. Sign provided with dual mounting arrangement of mounting on wall & celing both ( with flat rigid support/base).Sign is including all connection wires (upto 1 mtr) & high tensile strength zinc coated self tapering screws (4 nos with screw wall plastic packing), installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Providing and fixing at location a road reflective sign for directional use with 3M HIP grade II with Overlay paste on 3mm ACP with reviting on iron structure , board made with iron structure and fixed with internal M.S structure are installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

providing and fixing Acrylic channal letter, thickness of acrylic 3mm with 75mm raised letter, 1.2 w OSRAM make LED and water proof power supply will use to lite the letter, 12 mm WPC will use in back side of lette

M.S structure are installed at site on ground and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Supplying and placing of Outdoor Furniture Table,Material & Subtype Plastic - Polypropylene Table Top Material Polypropylene Leg Material Polypropylene Finish Matte Colour & Colour Family White Dimension (W)700mm X (D)700mm X (H)725mm Table Top Thickness 20mm Size Compact Style Modern Assembly Type Knock Down,The product must be from a Manufacturer having ISO 9001,ISO 14001 ,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE.

Supplying and placing of Outdoor Furniture Chair,Material & Subtype Rope,Plastic - Polypropylene Frame Material Polypropylene Seat Material Rope Leg Material Polypropylene Finish Matte Colour & Colour Family Green - Moss,White Dimension (W)540mm X (D)500mm X (H)800mm Seating Capacity 1 Seater Seating Height 460mm Size Compact Assembly Type Knock Down,The product must be from a Manufacturer having ISO 9001,ISO 14001 ,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE.

LABOUR CESS ( 1%)

Bidder Name

Amount

M/S S K TEKRIWAL (GSTN-20AARFS0465J1Z3) BID ID -671240

DILIGENT SERVICES (GSTN-NA) BID ID -670861

M/S S K TEKRIWAL (BID ID -671240)

M/S S K TEKRIWAL (BID ID -671240)