Repairs to various Snow clearance Machinery of Mechanical and Hospital Sub Division 1st Anantnag.

Amount

Repairs to various Snow clearance Machinery of Mechanical and Hospital Sub Division 1st Anantnag.

Repairs to blade assembly by way of dismantling the blade assembly like turn-buckle, base-plate, H-frame and V-blade. Then replacing the damaged H-frame with brackets with following dimensions:- i) top and bottom channel: ISMC100x50 L- 680mm (02no's) ii) vertical channel : ISMC 100x50 L-400mm (01no) iii)M.S gusset plate (T-4mm) triangular shaped: 150x150mm (04no's) iv) M.S Pin Brackets 19mm thick: 150x100mm(04no's). The job also involves providing and fitting of M18 Bolts for attaching of H-frame and V-blade (04 no's); Chassis and attachment plate (06 no's). M.S Pins Ø25mm L-6" with lock 03 no's for blade attachment will be provided by the department. The job also includes straightening of the base plate linkage by way of gas heating and hammering. the job also includes replacment of hydraulic jack seal kit and hydraulic pipe(1/2" 4800 psi L-10ft). Then assembling of all the linkages/parts and mounting of the blade assembly on the machine. All lead and lifts are in the scope of the contractor/firm. For Snow Cat 29 Farmtrac.

Re-wiring of complete faulty/damaged electrical wiring: by way of complete wiring in 1mm & 2.5mm multi-strand copper conducter as per the existing wiring circuit, including replacement of damaged/short-circuited relays, fuses, bulbs and testing the replaced circuits on load. The job also includes P/F of 2 no's tractor type 12V fog lights along with wiring, fuse and switch.For Snow Cat 29 Farmtrac.

P/F of wiper blade with arm For Snow Cat 29 Farmtrac.

Repairs/reinforcement to H-Frame top channel by way welding M.S plate 4mm thick 50mm wide L-220mm and 150mm on top and bottom resp. and bolt M18 L-3" (01 no's) For Snow Cat 28 Farmtrac.

Provinding and fitting of M.S Plate 8mm thick (50mmx50mm) 04 no's on the top channel of H-frame by way of welding and provinding of bolt M18 L-3" (02 no's) For Snow Cat 22 PREET.

FIXING OF CUTTING EDGES TO THE FIXED SNOW PLOUGH OF SNOW CATS . THE JOB INCLUDES REMOVING OF THE WORN-OUT CUTTING EDGES AND THEN CUTTING/ TRIMMING OF THE NEW CUTTING EDGES AS PER PLOUGH PROFILE BY USING A GAS CUTTER. THE JOB FURTHER INCLUDES DRILLING OF 16 NO HOLES ON THE NEW CUTTING EDGES IN ACCORDANCE WITH THE HOLES ON THE BASE OF THE SNOW PLOUGH. THE JOB ALSO INCLUDES PROVIDING AND FITTING OF 16 NO. NUTS BOLTS M18 OF 80 MM LONG For Snow Cat 22 PREET.

Providing and fitting universal shaft (as per sample) For Snow Cat 60HP SONALIKA.

FIXING OF CUTTING EDGES TO THE FIXED SNOW PLOUGH OF SNOW CATS . THE JOB INCLUDES REMOVING OF THE WORN-OUT CUTTING EDGES AND THEN CUTTING/ TRIMMING OF THE NEW CUTTING EDGES AS PER PLOUGH PROFILE BY USING A GAS CUTTER. THE JOB FURTHER INCLUDES DRILLING OF 16 NO HOLES ON THE NEW CUTTING EDGES IN ACCORDANCE WITH THE HOLES ON THE BASE OF THE SNOW PLOUGH. THE JOB ALSO INCLUDES PROVIDING AND FITTING OF 16 NO. NUTS BOLTS M18 OF 80 MM LONG For Snow Cat 60HP SONALIKA.

P/F of wiper blade with arm For Snow Cat 60HP SONALIKA.

P/F of 12V fog lights For Snow Machine 70 TATA LPT-715.

Repair to the Hydraulic jack of left side wing of V-blade assembly by way of welding the jack clevis by way of grinding off the debris from the clevis and end cap, then taper turning of the clevis neck and welding the jack clevis and end cap. The job also includes repairing of the 2 no's dameged hydraulic hose pipes (1/2" 4800) psi by way of cutting the off the damaged hose connection and fitting of new one's (as per sample) by way of crimping For Snow Machine GURU-03.

M/S MARTAND TRADERS