Design and Construction of Gate including Civil Electrical Illumination Beautification Landscaping of surrounding area and Signages etc works at Sunam District Sangrur Punjab

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres.

Cement Concrete 1:4:8 with stone ballast of size. 40 mm guage. using concrete mixing volumetric type

Reinforced cement concrete M-30 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Reinforced cement concrete M-30 mechanicaly batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in supersturcture.

Extra for RCC/PCC work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof.

Centring and shuttering for Columns (Square or Rectangular or ply gonal in plain)

Extra rate for shuttering work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof.

Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

Extra rate for shuttering work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof.

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Extra rate for shuttering work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof.

Centering and shuttering for faces of walls, partitions, retaining walls and the like (vertical or battering including attached pilasters buttresses etc.

Extra rate for shuttering work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof.

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

Extra for c above 4 meters (where any single storey exceeds 4 metres in height) for every additional height of 2 metres or part thereof for Brick Work/ Concrete Block/ Clay Block.

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes single socketed (working pressure 4 kgf / cm²) conforming to IS : 4985, including fixing with MS clamps. U-PVC pipes (working pressure 4 kgf. / sqcm) pipe 110 mm dia

Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Providing and fixing 110 mm dia SWR U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.

Bottom Khurra on ground 1.2m. x 0.6m. consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5m.m. thick cement plaster 1:3.

Providing and fixing in position gratings 150mm x 150mm for gully trap. PVC grating

Plastering on underside of ceiling 10 mm thick cement plaster 1:3

12.5mm thick cement plaster 1:4.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm guage and 100mm fine sand filling using mechanical mixer for mixing of material

Coloured Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps..

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra cost for providing corbelling/Brackets in 5 layers (3 Concave & 2 Curvature) at height of 13mtrncluding repairing and filling work making in good condition, cement primer complete in all respect as per architect drawing, specification and as desired by Engineer in charge. (RCC work will be paid in original item)

Providing and fixing in place jali with frame with base dimension as per drawing cast in GRC (technical specification of GRC- portland cement 10 kgs, Silica sand 8.5 Kgs, AR Glass Fibre 0.55 Kg, Water 2.4-2.7 litres, Polymer 1.0 1.2 Kgs & plasticizer 11.8-23.6 ml) over an armature made in MS pipe fixed with fasteners to the existing badse of RCC/Brick surface finished to the satisfaction of architect/ECI as per design complete in all respect. Final finish /cost of paint onot included in the cost

Cost for providing ornamental designing on parapet of height 1mtr in cement sand mortar 1:3 including repairing and filling work making in good condition, cement primer complete in all respect as per architect drawing, specification and as desired by Engineer in charge.

Extra cost for providing ornamental arch panel on face of pillar span of 1'-6" under various height of from base 3'-0" to top height 40'-0" with the help of Die made of MS Frame including repairing and filling work making in good condition, cement primer complete in all respect as per architect drawing, specification and as desired by Engineer in charge.

Extra cost for providing ornamental arch span of 30'-0" under base at height of 22'-0" & top height 35'-0" complete in all respect as per architect drawing, specification and as desired by Engineer in charge. (RCC work will be paid in original item)

Extra cost for providing ornamental arch span of 5'-0" under base at height of 18'-0" & top height 20'-3" complete in all respect as per architect drawing, specification and as desired by Engineer in charge. (RCC work will be paid in original item)

Extra cost for providing ornamental arch span of 5'-0" under base at height of 33'-0" & top height 34'-6" complete in all respect as per architect drawing, specification and as desired by Engineer in charge. (RCC work will be paid in original item)

Cold twisted deformed (Ribbed/ Tor Steel Bar/TMT) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @ 1.43litre/10 Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm

Finishing walls with textured exterior paint of required shade with two or more coats applied @ 3.28 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm

Providing and fixing face Tiles 230 x 38 x18 mm machine made vibro hydraulic compacted Burnt Clay brick Tile silicon coated on one side(Colour Terracotta series) on wall with under layer of 12 mm thick cement plaster 1:3 and jointed with neat cement matched with pigment complete as per drawings, specifications and to the entire satisfaction of engineer in- charge.

Providing, fabricating, supplying and fixing of 3D stainless steel letters/alphabets in English and Punjabi languages made of SS 304 grade sheet (minimum 1.5 mm thick) for signage, as per approved design, size, font and finish, including cutting, forming, welding, grinding and polishing complete; incorporating LED-based illumination (front-lit/backlit/edge-lit) with all accessories; fixing on any surface (RCC/masonry/stone/metal) at all heights using SS studs/spacers/brackets or concealed framework with approved weatherproof silicone sealant and necessary fasteners/anchors; ensuring durability against wind and environmental effects; including templates for alignment, corrosion protection, electrical connections, testing & commissioning, and all incidental works such as scaffolding, T&P, labour, packing, transportation in all leads & lifts, complete to the satisfaction of Engineer-in-Charge.

Providing, fabricating, casting and installing larger-than-life size statue of Shaheed Udham Singh Ji in bronze metal, as per approved composition, design, drawings and specifications, including preparation of sculpture at all stages from modelling to final casting, surface finishing, polishing and enamel/decorative work as approved by Engineer-in-Charge; providing and fixing suitable metal base, structural supports and anchoring system designed to withstand wind load and seismic forces; complete with packing, transportation to site in all leads and lifts, erection, alignment, fixing with all necessary accessories, and installation complete in all respects to the satisfaction of Engineer-in-Charge.

Excavation in Soil (any type) using Hydraulic Excavator CK 90 Excavation with hydraulic excavator of 0.9 cum bucket capacity including cutting trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lift and combined lead up to 60 mtr.

Compacting of earth work & preparation of sub grade including loosening and leveling of earth 225mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering rolling with a road roller and compacting the bed to achieve minimum dry density as given in table 300-2 as per technical clause 305 of MORT&H specification.

Construction of granular sub-base by providing material as per grading-III (Table 400-I of MORT&H 5th revision), mixing in a mechanical mix plant at OMC, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications

Providing and laying factory made rubber moulded smooth finish cement concrete Kerb M-20 grade 250mm high with bottom width 165mm and top width 115mm made over strong vibratory table and fixing with cement mortar 1:2 as per MORT&H specifications.

Water Bound Macadam Grading I (with screening ) Providing, laying, spreading and compacting stone aggregates of Grading I to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical clause 404 of MORT&H specifications

Water Bound Macadam Grading II (with screening ) Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical clause 404 of MORT&H specifications

Providing and laying surface dressing in single coat using crushed stone aggregates of specified size on a layer of bituminous binder VG-10 @ 1kg per sqm laid on prepared surface after cleaning the road surface and rolling with 8-10 tonne smooth wheeled steel roller complete as per technical clause 509 of MORT&H specifications

Dismantling of existing damaged Bitumen surface by Cold Milling Machine upto 30 mm depth

Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical specifications

Providing and laying bituminous concrete 30mm to 45mm thick with batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.4%, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of MORT&H specifications

Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M- 35 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-inCharge.

Providing and making rumble strips 15-20mm high at centre, 250mm wide placed at 1m centre to centre over freshly laid bituminous layer by using close graded premix surfacing material type B and thermoplastic road marking paint shall conform to technical clause 803 to MORT&H specifications.

Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications

Cautionary sign board 900x900x900mm triangular as per IRC 67-2001 with retro reflective high intensity microprismatic grade sheeting fixed over 2mm thick aluminium sheet with 25x25x3mm angle iron frame supported on a mild steel angle iron post 65x65x6mm without cost of definition plate firmly fixed to ground in foundation concrete 1:2:4 of size 0.45x0.45x0.60m for vertical post complete as per technical clause 801 of MORT&H specifications. Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012

Informatory sign board 600x600mm square as per IRC 67-2001 with retro reflective high intensity microprismatic grade sheeting fixed over 2mm thick aluminium sheet with 25x25x3mm angle iron frame supported on two mild steel angle iron post 65x65x6mm firmly fixed to ground in foundation concrete 1:2:4 of size 0.45x0.45x0.60m for vertical post complete as per technical clause 801 of MORT&H specifications. Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012.

Place identification sign board 900x600mm rectangular as per IRC 67-2001 with retro reflective high intensity microprismatic grade sheeting fixed over 2mm thick aluminium sheet with 25x25x3mm angle iron frame supported on two mild steel angle iron post 65x65x6mm firmly fixed to ground in foundation concrete 1:2:4 of size 0.45x0.45x0.60m for vertical post complete as per technical clause 801 of MORT&H specifications. Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012.

Informatory sign board 600x450mm rectangular as per IRC 67-2001 with retro reflective high intensity microprismatic grade sheeting fixed over 2mm thick aluminium sheet with 25x25x3mm angle iron frame supported on two mild steel angle iron post 65x65x6mm firmly fixed to ground in foundation concrete 1:2:4 of size 0.45x0.45x0.60m for vertical post complete as per technical clause 801 of MORT&H specifications. Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012.

Hazard Marker sign board 300x900mm rectangular as per IRC 67- 2012 with high intensity Microprismatic grade retro reflective Sheeting as per ASTM D 4956 09 and IRC 67 2012, fixed over 4mm thick Aluminium Composite Material (ACM) sheeting having skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 firmly fixed to ground including foundation concrete M-25 of size 0.45x0.45x0.60m for vertical post complete as per clause 801 of MORT&H specifications. b) Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012

Advance Direction sign board 1200x900mm rectangular per IRC 67- 2012 with high intensity Microprismatic grade retro reflective Sheeting as per ASTM D 4956 – 09 and as per IRC 67 – 2012. grade sheeting fixed over 4mm thick Aluminium Composite Material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on two square hollow steel sectionpost 60x60x3.2mm conforming to IS 4923 firmly fixed to ground in foundation concrete M-25 of size 0.60x0.60x0.75m for vertical post complete as per clause 801 of MORT&H specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports from an independent test laboratory conforming to clause 6.7 of IRC 67-2012 . b) Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012

Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications.

Planting seasonal flower in beds (a) Planting seedlings including digging of beds to15cm depth and mixing FYM, fertilizer and insecticides, planting of seedlings at 20cm distance from plant to plant and row to row.

Planting hedge including digging of trench 60cm wide to15cm depth and mixing FYM, fertilizer and insecticides, planting of sapling at 30cm distance from plant to plant in two rows.

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Supply and erection of PVC insulated PVC sheathed FR (2Core) round flexible wire with copper conductor cable (ISI marked) confirm to IS:694/1990 left bare in pipe or on surface with cleats of suitable size complete in all respect as desired by the Engineer-in-charge:-

Supply and erection of PVC insulated PVC sheathed (3 core) round flexible wire with copper conductor (FR) cable (ISI marked) confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS:7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-

Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-

Supply and erection of PVC flexible pipe complete without compression glands, locking arrangement, check-nuts as required:-

Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-

Supply and erection of RCCB (Residual Current Circuit Breaker) for Earth leakage protection suitable for 240/415 volts 50 cycles AC supply with breaking capacity of 10kA as per IEC 61008-1 in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-

Supply and erection of sheet metal Double Door Distribution Boards IP 43-IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-

Supply and erection of Single phase copper wound Automatic voltage stablizer of suitable capacity electronically controlled circuit with input voltage 140-260 volts single phase AC supply and output voltage 220 ± 5% volts single phase AC supply having main silicon core copper wound step up transformer with suitable nos. of turns on primary side and secondary side the transformer should be fully insulated inside the MS sheet box of suitable size. There should be power control relay and single pole MCB (C-curve, 10kA) of suitable capacity complete with internal copper wiring along with amp. meter and volt meter, high voltage cut off 280 volt input (240 volt output) and 90 volt maximum boost and overloading protection to be provided:-

Supply and erection of SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirming to IS:14772, (Recessed/ On surface), robustly constructed, safe & shock proof, rust & tamper proof of suitable inner & outer dimensions with ± 10% tolerance in size & hinged water tight cover with locking arrangement complete in all respect as approved and desired by the Engineer In-Charge at site:-

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Supply, Installation, Testing and Commissioning of 24–25W LED Wall Washer/Wall Grazer (RGBW) 1 mtr. length, complete with inbuilt driver (240V AC), CCT-RGBW, beam angle 25°–30°, IP67 protection, 10kV surge protection with external SPD, including mounting bracket, all materials and labour, as per specifications and to the satisfaction of Engineer-in-Charge, approved make: Wipro/Havells/Philips/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of 70W–75W LED Flood Light (RGBW), complete with four-housing platform, inbuilt driver (240V AC), CCT-RGBW, beam angle 25°–30°, IP67 protection, 10kV surge protection with external SPD, including mounting bracket, all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Philips/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of 18W LED Inground Light (RGBW), complete with high-purity lens for pillar illumination, RGBW color temperature, 30° beam angle, and IP67 protection, BIS approved, including all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of DMX Controller, 4-channel, suitable for controlling RGBW LED lighting fixtures, compatible with standard DMX512 protocol, complete with required power supply, control interfaces, wiring, and accessories, programming, including all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of DMX Splitter, 8-way, suitable for distribution of DMX512 signal for RGBW LED lighting fixtures, with optically isolated outputs for reliable signal transmission, complete with inbuilt power supply (240V AC), required input/output ports, wiring, and accessories, including all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of L.T. Spare DMX Male and Female Supply Cable, 4 Core, 1 metre length, suitable for DMX512 control systems for RGBW LED lighting fixtures, complete with connectors, insulation, and required accessories, including all materials as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply, Installation, Testing and Commissioning of IP68-rated 4-pin connector, suitable for outdoor RGBW LED lighting systems, ensuring waterproof and dustproof connections, complete with compatible cables, sealing accessories, and all required materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply and Installation of 24U Equipment Rack, Floor-mounted type, suitable for housing DMX controllers, splitters, and associated lighting control equipment, fabricated from high-quality CRCA steel with proper ventilation, lockable front glass door, removable side panels, cable management provisions, and earthing arrangement, complete with power distribution unit (PDU), mounting hardware, and all accessories, including all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Valrack/NetRack/APW President or equivalent.

Supply, Installation, Testing and Commissioning of DMX Coder, suitable for controlling RGBW LED lighting fixtures via DMX512 protocol, providing programmable control of channels, scenes, and effects, complete with required power supply, control interfaces, wiring, and accessories, including all materials and labour, as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Wipro/Havells/Bajaj or equivalent.

Supply of 4-conductor (2-pair twisted) multi-pair cable, 24 AWG with foil shielding, suitable for DMX512 signal transmission and RGBW LED lighting control systems, complete with insulation, shielding, and all required accessories, including all materials as per specifications and to the satisfaction of the Engineer-in-Charge, approved make: Belden/Finolex/Polycab or equivalent.

Total

Note: Being a percentage tender, the bidder shall quote its price as at par or percentage above or percentage below the estimated total cost in the Bill of Quantities as specified.

GRAND TOTAL