Repair maint of flooring roof sheets ceiling and other connected works under Central Amenities under GE Gangtok

Amount

Dismantling Wrought Iron or Mild Steel Work, viz. Mild Steel Flat Iron (Wind Tie) and Similar Work including Mild Steel Bolts, Nuts, etc., complete all as specified and as directed.

Taking down chowkats with shutter of any description (without taking down shutter from the frame) exc 1.5 Sqm and n.exc 4.00 Sqm each and removing from site complete all as specified and as directed.

Taking down chowkats with shutter of any description (without taking down shutter from the frame) n.exc 1.5 Sqm each and removing from site complete all as specified and as directed.

Taking down shutters of any description 1 Sqm but n.exc 2 Sqm each and removal from site complete all as specified and as directed

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), removing from the Sites and rubbish off the Premises, complete all as specified and as directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc., complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for and removal of rubbish of the site complete all as directed (reinforcement cut as required to facilitate demolition).

Demolition of precast concrete block walling built in cement mortar complete all as specified and as directed.

Dismantling old PGI/CGI/AC sheeting any gauge, thickness including Nainital, Sikkim or similar pattern roof/facia including ridge etc and keeping serviceable sheets in safe custody for re-use complete all as specified and as directed.

M&L for 35mm thick 2nd class HW plain, framed, paneled shutters (two panel) with lock rail and panel of 9mm thick BWR commerical ply or 12mm veneered particle board with commercial face veneering on both faces. The size of rail & site as per IS : 1003 (Part-I), Kiln, seasoned & chemically pressure, treated complete all as specified and as directed.

M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 30mm thick flush door shutter, solid core construction, with block board core and plywood face panels. Commercial type on one side and other face coverd with decorative face veneer with 6mm thick teak wood lipping/frame to match complete all as specified and as directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F of factory made solid PVC door frame of size 50mmx47mm made out of 5mm thick single side prelaminated PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelaminated sheet as per specification and drawing) complete all as specified and as directed.

S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, solid steel frame shall be covered with heat moulded single side prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of both side prelam PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing complete all as specified and as directed.

S&F 250mm aluminium anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 150mm long aluminium anodised handles, cast type, complete all as specified and as directed.

S&F for 100mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F 150mm long aluminium anodised tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100mm long aluminium anodised tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100mm long electrolated butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.

S&F 100mm size brass handles (decorative type) cast type polished bright complete all as specified and as directed.

S&F 75mm long electrolated butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.

S&F continous (piano) hinges, 30mm width of flap, mild steel, bright finish or electro galvanised fixed with stainless steel screws complete all as specified and as directed.

M&L for 12mm thick plywood grade, BWR type BB fixed with screws to timber frame work/steel frame work with screws to frame work in repair complete all as specified and as directed.

S&F laminated wooden flooring 8mm thick including 5mm thick profile sheet(for sound proof) as in floors, ceiling fixed with self tapping screws on wooden/steel frame work complete all as specified and as directed.

M&L for two coats of aluminium painting to new steel surface over a coat of aluminium red oxide primer including preparation of surfaces area exc 10cm width & girth complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping including necessary formwork complete all as specified and as directed.

S&F bib tap, long body cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI pipe or for brass ferrule including taking down old unserviceable one. Make : ESSCO CAT Part No. SQT-511 KN or equivalent approved make.

S&F in repair hand shower(health faucet) 8mm dia alongwith 1m flexible tube and wall hook fixed in position complete all as specified and as directed. Make : JAQUAR Code-ALD-573 or equivalent approved make.

Supply and fixed 15mm bore pillar taps, fancy type with long neck with aerator cast copper alloy with capstan head, chromium plated, screwed down, high pressure with long screwed shanks, fly-nuts, with screwed for GI pipe complete all as specified and as directed. Make : ESSCO Cat part No. SQT-508KN or equivalent/approved make complete all as specified and asi directed.

S&F 15mm bore dia angular stop cocks, chromium plated, with wall flange screwed down, screwed from iron pipe or union and complete all as specified and as directed. Make : ESSCO Code-TQT 513A or equivalent make as approved.

S&F in repairs 15mm bore Brass CP mixer for mixing holt & cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make : ESSCO Cat Part No. SQT 516KN or equivalent approved make.

S&F for 15mm bore concealed stop cock fancy type chromium plated with long shank and cup complete all as specified and as directed. Make : ESSCO SQT 514 EKN or equivalent approved make.

Taking up or down 15mm bore dia steel water tubings including fittings etc complete and making good disturbed surfaces of walls/ ceilings etc complete all as directed.

Taking up or down 20mm bore steel water tubings including fittings etc complete and making good disturbed surfaces of walls/ ceiling etc complete all as specified and as directed.

Supply and fix galvanised steel water tubing 15mm bore medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Supply and fix galvanised steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Fixing only galvanised steel water tubing 15mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Fixing only galvanised steel water tubing 20mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Cutting chases for concealed water tubing pinning in, and making good to facing where required and pointing in cement mortar (1:3) and making good cutting n.exc 10cm girth in concrete block complete all as specified and as directed.

Materials & labour for coloured glazed ceramic tiles of size (300x200mm/350x250mm/450x350mm) of 7mm thick, as in vertical surfaces such as skirting/dado/riser to steps etc conforming to IS-13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed/backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.

Material & labor for non skid coloured ceramic tiles of 7 to 8mm thick ( Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc conforming to IS-13712, grade B-II-(a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.

M&L for Dark shade vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed/bedding layer in cement mortar (1:6) complete all as specified and as directed.

M&L for Dark shade vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in verticle surfaces such as skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed/backing layer in cement mortar 1:4 complete all as specified and as directed.

M&L for 25mm thick PCC(1:2:4), type B0 (using 12.5mm graded stone aggregate) as in sub-base of floor finished rough for receiving floor finishes complete all as specified and as directed.

M&L for 100mm thick PCC (1:2:4), type B2 (using 40mm graded stone aggregate) as in hardstanding/flooring etc finished even and fair without using extra cement including necessary formwork complete all as specified and as directed.

M&L for hardcore of guage n.exc 0.63mm broken stone or boulders deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified & as directed.

M&L for 75mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in path/steps etc finished even and fair without using extra cement incluidng necessary formwork complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 20mm thick in cement mortar (1:4) in two layer of 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer's instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only)

M&L for 10mm thick in cement mortar 1:4 as in concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Material & labour for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and as directed.

Taking down eaves gutter and rain water pipes (any size and pattern), including all fittings, heads, shoes, bends, swan necks etc including removal to stores complete all as specified and as directed.

S&F for PVC (SWR) half round 150mm dia with rounded edges as in eaves gutter including all accessories like bend , T etc complete all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or in floor with necessary clamps, bolts, bends, Tee bend of any radius for PVC(SWR) pipes/steel gutters etc fixed to walls complete all as specified and as directed.

Supply and fix in repairs 110mm bore PVC(SWR) bend of any radius for PVC (SWR) pipes/steel gutters etc, fixed to walls complete all as specified and as directed.

Supply and fix 110mm bore PVC(SWR) junction single, (Single T ) equal or unequal with access door complete all as specified and as directed.

S&F in repairs 75mm bore, PVC(SWR) pipes of pressure rating 4 kgf/cm2, single socketed in any length with rubber ring joints, laid in trenches or under floors including necessary earthwork, fixed on walls complete all as specified and as directed.

S&F in repairs 75mm bore, PVC(SWR) bend of any radius for PVC (SWR) pipes/steel gutters etc, fixed to walls complete all as specified and as directed.

S&F in repair 75mm bore PVC(SWR) junction single (Single T) equal or unequal with access door complete all as specified and as directed.

S&F in repair PVC(SWR) 50mm bore pipes single sockets, in any length with rubber ring joints, laid in trenches or in floor with necessary clamps, bolts, bends, Tee complete all as specified and as directed.

S&F PVC floor trap/Nahani trap, 100mm diameter of outlet, with gratings including jointing to waste pipe fixed in PCC 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and as directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in ridges, valley, eaves etc fixed with self tapping screws complete all as specified and as directed.

M&L for preparation of old/new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer applied over 3mm thick super fine Birla or altek wall care putty finish including complete removal of existing treatment complete all as specified and as directed.

M&L for applying two coats of exterior acrylic emulsion painting over a coat of alkali resistant primer including scafolding upto 15m height and preparation of old/new surface complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description n.exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously un-treated steel surfaces of any description over 10cm in width or girth including preparation of new steel surfaces complete all as specified and as directed.

Supply and fixing in repair snow white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 705x310x 770 mm with 'P' or 'S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device, making all necessary connections complete all as specified and as directed. Make : CERA Cat No. S1013119 or equivalent approved make.

S&F in repair snow white/ivory vitreous china wash hand basin 630x510x180mm with padestal including CP waste coupling complete all as specified and as directed. (Make : Cera Cat Part No. S2040111(WHB) and Cat Part No. S2090107 (Padestal) complete all as specified and as directed.

Supply and fix PVC connections 15mm size with PTMT/Brass nuts of length 600mm complete all as directed by the Engr-in-Charge. Make Prayag or equivalent make approved.

Supply and fix in repair 10 litre capacity low level PVC flushing cistern(white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed. Make : ESSCO Cat part no. WHE-WHT-183L or equivalent approved make complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor''s workshop before fabrication complete all as specified and as directed.

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and/or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

S&F for rolled section as in stairs (framed) including stringers, treades, landing, balusters, hand rails etc including cleats, brackets etc complete including necessary fabrication wherever reqd conforming to Fe-290 (Gde-E165) complete all as specified and as directed.

Dismantling of wall and ceiling hard boards/AC sheets(Fibre pulp insulation etc) or insulation board and plywood in any thickness & any position including cover fillets complete all as specified and as directed.

S&F 5-6mm thick PVC ceiling/wall panels of interlocking types, width 250/255mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, corner cove, F/J edge trims where required fixed with hidden screws including steel/wooden frame work complete all as specified and as directed.

Excavating in post holes (or similar holes) each n.exc 0.5 Cum getting out and removing surplus soil to a distance n.exc 50m and making good surfaces in soft/loose soil complete all as specified and as directed.

M&L for 18-20mm thick Granite Slab green in one piece machine cut, as in steps, jambs, pillars, window cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing including rounding to edges of stone slabs such as in steps, cooking platforms, and other similar situations over and including 20mm thick bedding/backing layer in cement mortar (1:6) complete all as specified and as directed.

M&L for bevelling/rounding to edges of granite slab one edge including rubbing and polishing etc complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally, hooping for columns, hookings ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for labour for Mild steel TMT bars 5mm dia and over upto including 10mm dia as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for labour for RCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies and in shelves and the like work including necessary form work complete all as specified and as directed. Note : Re-inforcement shall be measured and paid separately.

S&F door closer hydraulically regulated, aluminium(die cast) body designation No.3, universal type, suitable for door shutters or 701 to 850mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150mm complete all as specified and as directed.

M&L for brickwork with subclass ''B'' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks, type C1 1:3:6 (20mm graded stone aggregate) exc 10cm in width and setting in mortar 1:6, complete all as specified and as directed.

Demolition to cement concrete of any description and in any position not otherwise specifically provided for (unreinforced) complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.00 Kg of cement per Sqm complete all as specified and as directed.

M&L for 15mm thick cement screed in cement mortar 1:3 admixed with integral water proofing compound FOSROC complast x 412 IC @ 130 ml per bag cement including a bonding coat of FOSROC''s NiTCO bond AR cement slurry/shalimar Tar product, Mumbai No. 1 liquid @ 200ml per bag complete all as specified and as directed and as per manufactuer's instructions including teting for leakproof treatment.

M&L APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. Not less than 150 gms/ Sqm) laid on primed surface by forced application complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in roof padding to bring top surface of slab in slope complete all as specified and as directed.

S&F grating 100mm dia with hole of PTMT/CP (medium weight 25 gms) complete all as specified and as directed.

S&F powder coated aluminium anodised (min 50 micron) heavy duty aluminium frame for partition etc including fixing with 5.5mm tinted glass including joining cleat for fixing, glazing clips, aluminium snap beading, rubber nuprene gasket, packing handle including all necessary fitting required complete all as specified and as directed.

S&F powder coated aluminium anodised (min 50 micron) heavy duty aluminium frame for doors/windows shutter etc including fixing with 5.5 mm thick including joining cleat for fixing, glazing clips, aluminium snap beading, rubber nuprene gasket, handles locking arrangement incl all necessary fitting reqd complete all as specified and as directed.

S&F in repair powder coated aluminium alloy three track sliding window frames of size 62mmx28mmx1mm thick or nearest appropriate section and shutter of section 20mmx40mmx1mm or nearest appropriate section with two shutters 5mm thick tinted sheet glass for glazed shutter (window frame having weight 0.55 Kg/RM) with rubber gasket, handle, locking arrangement etc including taking down old steel/wooden windows complete all as specified and as directed.

S&F stainless steel hand rail 40mm dia of (Gde 304) as in railing complete all as specified and as directed.

S&F stainless steel decorative type dom incl necessary fabrication or riveting complete all as specified and as directed.

Demolition of stone or boulders masonry built in cement mortar including all quoins, arches, pillars, pre-cast PCC bond stones with separating serviceable stones & setting aside for reuse in the work complete all as specified and as directed.

M&L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) including brought up to courses complete all as specified and as directed.

All as per Sl item No. 102 here-in-above but except stone. Note :- Stone boulders obtained from item No. 125 here-in-above.

Labour only for hand packing (any thickness) at back of walls over arches etc and raising(or lowering) to the required level. Note : - Stone boulders obtained from item No. 128 her-in-above.

S&F in repairs decorative type curtain rod, chromium plated with fixing brackets, stops and complete fitments complete all as specified and as directed.

M&L for lacquer coated coloured chequered cement concrete tiles of size 300x300x25mm thick set, jointed and pointed in neat slurry in floors and steps with grey cement and pigments over and incl 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and as directed.

Supply and fix in repairs CP tubular towel rack 600 mm long with and including chromium plated brass screws complete all as specified& as directed. Make: Jaquar Cat AKP-35781PS or equivalent of approved make.

Supply and fix in repair CP corner glass shelf with bracket of size 25 x 25 cm fixed to plugs with brass screws on wall complete all as directed. Make:Jaquar Cat No ACN-1173 or equivalent of approved make.

M/S ANIL KUMAR THAKUR

DHARMINDER SINGH

MAHENDRA KHAWAS

BIJAY MITTAL

NISHA CONSTRUCTIONS

SHANTI KHAWAS AND SONS

M/S MANOJ VERMA