SPECIAL REPAIR TO TOILETS AT KV NO. 1 AT AF STN ADAMPUR

Amount

B/R WORKS

PCC type E-2 (1:5:10), using 40 mm graded stone aggregates as in filling & mass concrete, sub base, complete all as specified.

PCC type C-0 (1:3:6), using 12.5 mm graded stone aggregates as in filling of MS sheet chowkats, complete all as specified.

Reinforced cement concrete, type B-1, using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Brick work using bricks as specified in PS-II clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified.

Brick work using old size bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4), complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished surfaces of concrete, complete all as specified.

Factory made, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, 35 mm thick, ISI marked, complete all as specified.

Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm plain PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening, complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified.

Factory made PVC cup board shutter 25 mm thick consisting of frame made out of MS tube 15 x 15 mm for stiles & rails (Size 100 mm x 25 mm), MS frame shall be covered with 5 mm thick heat moulded PVC sheet 'C' channel having 5 mm thick PVC sheet strip of 15 mm width stuck inside with slvent cement forming stiles & rails. Panelling of plain colour 5 mm thick PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as shown on diiagram at Serial Page 171 of MES Schedule Part-I (2009), complete.

Stainless steel 100mm long butt hinges with stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. HG-2412 or equivalent make mentioned in Appndix 'B'

Stainless steel, barrel tower bolt, 150 mm long, with stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. TBS-2150 or equivalent make mentioned in Appndix 'B'

Stailess steel, sliding door bolts, with length of bolt 250 mm, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, all as specified. MAKE :PRAYAG CAT NO. LD-1210 or equivalent make mentioned in Appndix 'B'

Stailess steel, handle, 150 mm long, curve shapewith stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. DHC-2150 or equivalent make mentioned in Appndix 'B'

Door closer hydraulically regulated, aluminium die cast body, designation No. 3 universal type, suitable for door shutters up to 851 to 1000 mm in width and of weight between 61 to 80 kg, ISI marked, IN REPAIR complete all as specified.

Stainless steel (SS-304 grade) tube having external dia not less tha 25 mm and of weight not less than 1.30 kg/metre fixed to walls with stainless steel brackets as railing for phyically challenged persons complete.

Mild steel TMT bars 6-8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Factory made pressed steel frames, conforming to IS, having profile 165 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., complete, as specified, supplied and fixed with one shop coat of zinc chromate primer, complete all as specified.

50 mm thick, cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate, finished even & smooth, as in floors, complete all as specified.

Granite jet black shade, 15-18 mm thick, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified.

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

First quality, glazed ceramic, straight cut/joint free, 6-7 mm thick colored tiles, area of each tile exceeding 0.17 sq.m but not exceeding 0.19 Sq.m, on vertical surfaces such as dado etc over & including 10 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tiles, complete, all as specified.

First quality, non-skid ceramic, straight cut/joint free, 7-8 mm thick colored tiles, area of each tile exceeding 0.11 sq.m but not exceeding 0.18 Sq.m, in floors etc. over & including 15 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry & pointed with grout of matching shade, complete, all as specified.

Factory made PCC type A-1 chequered tiles, ISI marked (IS:13801), with grey cement & no pigment, 22-25 mm thick, of size 250 mm x 250 mm, in floors, over & including 15 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry, complete, all as specified.

Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified.

Plain Sheet glass 4 mm thick, ordinary quality in squares not exceeding 0.5 Square metre in each pane, including hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frame including punching or drilling out old glazing pins/spring clips, complete all as specified.

Complete removal of existing treatment of any description on old wall surfaces of any description, prepration of surfaces and applying two coats of cement base paint, complete all as specified.

Prepration of plastered ciling surfaces complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer.

Prepration of plastered wall surfaces complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer.

Two coats of synthetic enamel paint over & including a coat of pink primer over new wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

Two coats of synthetic enamel paint over steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, including taking up or down existing unserviceable steel tubing and connections, complete all as specified of size: -

15 mm bore

20 mm bore

Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, IN REPAIR, complete all as specified.

Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

2-way bib cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

Pillar cock, swan neck type, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

Stainless steel round slotted grating with frame, 100 mm size and fixed in position with cement joints, IN REPAIR complete all as specified.

Cast copper alloy, chromium plated towel rail, 600mm size & dia of tube not less than 20 mm, IN REPAIR, complete.

Soap dispenser holder with soap container, complete. MAKE: PRAYAG Cat No. BA-83 or equivalent make mentioned in Appndix 'B'.

Grab Bar, cast copper alloy, chromium plated 225 mm size and fixed in position complete.

Toilet paper holder, cast copper alloy, chromium plated, glossy finish and fixed in position, IN REPAIR, complete. MAKE: PRAYAG Cat No. BA-18 or equivalent make mentioned in Appndix 'B'.

Towel rack, cast copper alloy, chromium plated, glossy finish, complete. MAKE: PRAYAG Cat No. BA-32 or equivalent make mentioned in Appndix 'B'.

Corner glass shelf 300 mm (with ABS brackets) complete. MAKE: PRAYAG Cat No. BEA-46 or equivalent make mentioned in Appndix 'B'.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe), IN REPAIR, complete all as specified.

Vitreous China wash down water closet pan (pedestal pattern), white, including fixing acessories, IN REPAIR, complete all as specified.

PVC water closet seat and white cover with & including mild steel chromium plated hinging device & rag bolts, IN REPAIR, complete all as specified.

Jet spray (L-bend type) stainless steel body with 1.5 metre length braided tube, IN REPAIR complete.

Health faucet CP brass body with wall hook and 1 metre SS tube complete.

PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked (IS: 7231) with flush pipe and all fixing arrangements, IN REPAIR, complete all as specified.

Vitreous China counter type wash basin, white, size 500 x 400 x 130 mm, with & including cast copper alloy, half or full threaded chromium plated waste coupling suitable for & including 32 mm size PVC waste/discharge pipe, IN REPAIR, complete.

Fancy type 5-6 mm thick looking glass fixed over not less than 6 mm thick PVC ply and approved shade PVC beading not less than 15 mm wide alround with and including all fixing acessories, includiing taking down existing looking glasses (600 x 450 mm size) complete.

PVC connections 15 mm size of length 600 mm with PTMT nuts, IN REPAIR, complete all as specified.

Vitreous China Urinal Pot, half stall type, white of size 345X320X560, with & including cast copper alloy, chromium plated waste coupling half or full threaded suitable for & including 32 mm size PVC waste/discharge pipe, flush cock (lever type) 25 mm size, IN REPAIR, complete. MAKE OF URINAL:PRAYAG CAT NO. 4998 or equivalent make mentioned in Appndix 'B'

High pressure laminate urinal partition not less than 12 mm thick of size 550 x 900 mm, with and including all fixing acessories, complete.

uPVC pipes, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors as SWR pipes, IN REPAIR, complete all as specified of size: -

75 mm external dia pipe

110 mm external dia pipe

uPVC/PVC bend any radius, complete all as specified. suitable for uPVC soil waste discharge pipes, IN REPAIR, of size: -

75 mm external dia pipe

110 mm external dia pipe

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement for 110 mm external dia, type-B pipes, IN REPAIR, complete all as specified.

E/M WORKS

Point wiring with multi-stranded copper conductor, single core, PVC insulated and unsheathed cable, including PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, GI terminal boxes, covered with & including 3 mm thick plastic laminated sheet top cover etc. comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

NOTE FOR SERIAL ITEM 63,63.1-63.4: (a) Switch(es), socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. (b) Terminal boxes shall be fixed flush to walls with cement & sand mortar (1:4) complete on the location as approved by EIC. (b) In ceiling portion PVC Conduit shall be fixed/laid on surface.

Switch piano, flush button, single pole, one way, 6 Amp complete all as specified.

Switch piano, flush button, single pole, one way, 16 Amp complete all as specified.

Socket outlet, 3/5 pin, single pole, 6 Amp, complete all as specified.

Socket outlet for two-in-one 3 pin 6 Amp & 3 pin 16 Amp, complete all as specified.

Ceiling rose, surface bakelite, 65 x 50mm, three terminals complete, all as specified.

Lamp (angle) holder, insulated body, cord grip pattern, complete, all as specified.

Sub main wiring (with approved colour coding as per IS) with single core FRLS PVC insulated flexible stranded copper conductor 1.1 KV grade (main cable: number of runs as indicated below along with single core FRLS PVC insulated flexible stranded copper conductor 1.1 KV grade for earthing in conduits, complete all as specified of sectional area: -

2 runs of 4 sq. mm main cable + 1 run of 4 sq. mm earth cable

NOTES: (i) Conduit & conduit accessories shall be measured & paid for separately under respective item of BoQ. (ii) For payment purposes, total runs of main cable (each run of one running metre) as mentioned above and one run (one running metre) of earth cable shall be considered together as "1 RUNNING METRE"

20 mm dia, rigid non metallic PVC concealed conduit, 'ISI marked' , inclusive of all fittings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing accessories such as couplers lock nuts, saddles, pipe hooks etc for wiring, complete all as specified.

Sheet metal enclosure for DB for fixing MCB’s, isolators etc., having IP-43 protection, suitable for surface and flush mounting, for SPN, 4 way with 200 Amp rated bus bar, 230 V, IN REPAIR, complete all as specified.

MCB, 6-32 Amp, 240 volt, single pole, breaking capacity not less than 10 kA, 'C' curve/series, complete all as specified.

MCB, 6-32 Amp, 240 volt, single pole & neutral, breaking capacity not less than 10 kA, 'C' curve/series, complete all as specified.

Blanking plate of plastic to cover unused space in DB's complete all as specified.

LED wall mounted batten light luminaire 20 watt comprises of extruded channe in thermally conductive materil, high translucent serrated milky white diffuser to get glare free and smooth light distribution having efficacy not less than 90 lumen/watt complete. MAKE: Crompton Cat Part No. LDL-20-CDL or equivalent in makes mentioned in Appendix 'B' here-in-after.

Environment friendly, energy saving surface mounted, decorative oval bulk head edge lit 10 watt bulk head LED luminaire, lumen output should not be less than 90 lumens per watt complete. MAKE: Havells Cat Part No. LHEOAOP7UZ6W010 or equivalent in makes mentioned in Appendix 'B' here-in-after.

Exhaust fan 380 mm sweep, heavy duty with louvers and connecting up complete from ceiling rose or connector to fan, complete all as specified.

DISMANLING/DEMOLITION WORKS

Taking down chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), complete all as specified.

Taking down chowkhats or frame exceeding 1.5 Sq. m but not exceeding 4 Sq. m each with shutter(s) (without taking off shutters from the frame), complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding on brick walls including racking out joints hacking for key and scrubbing removing rubbish from premises, complete all as specified.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified.

Dismantling of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete with batten, casing caping of MS or and PVC conduit on surface or concealed, including switches, ceiling roses, pendants, regulators, sockets, mild steel terminal boxes etc., removing materials complete all as specified.

Taking down carefully copper/aluminium sub main wiring complete, including existing batten/conduit consealed/surface etc., removing materials complete all as specified.

Disconnecting and taking down light fitting of any description, complete all as specified.

B S ENTERPRISES

LABH SINGH AND SONS