CONSTRUCTION WORK OF BAZAR YARD, TAH.-SUAR, DISTT.-RAMPUR

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil D.S.R. Item No. 2.28.1

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : All kinds of soil D.S.R. Item No. 2.2.1 1

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. D.S.R. Item No. 2.25(a)

Providing & laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) D.S.R. Item No. 4.1.8

C.C. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) D.S.R. Item No. 4.1.3

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) D.S.R. Item No. 4.10

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources and using recycled concrete aggregate (RCA) as coarse aggregate and fine aggregate within permissible utilization of 20% each, Portland Pozzolana /Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto Plinth level D.S.R. Item No. 5.33.1.1

All works above plinth level upto floor V level D.S.R. Item No. 5.33.2.1

S&F Mild steel or iron in plain work such as reinforced concrete and reinf. b/work (when not included in overall rate) wrougt to required shape as necessary Including bending for proper completion of work and incl supply of all steel and wastage and overlapping and hook D.S.R. Item No. 5.22.1

Centering and shuttering including strutting, propping etc. and removal of form for : Foundation, footing, bases of columns etc. for mass concrete DSR 5.9.1

Columns, Pillars, Piers, Abutments, Posts and Struts D.S.R. Item No. 5.9.6

Lintels, beams, plinth beams, girders, bressumers and cantilevers D.S.R. Item No. 5.9.5

Suspended floors, roofs, landings, balconies and access platform D.S.R. Item No. 5.9.3

Centering and shuttering including strutting, propping etc. Cornices and mouldings D.S.R. Item No. 5.9.17

Brick work in foundation 1st class b/work in 1:4cement and couarse sand mortar in fdn and plinth incl. supply of all materials , labour and t& P required for proper completion of the work D.S.R. Item No. 6.2.1

Brick work in SUPER STRUCTURE in 23 cm thk wall with 1:4 cement and coarse sand incl. all materials labour annd t&p etc. for proper completion of work. Ground Floor D.S.R. Item No. 6.4.1

Class 150 Brick work in 1:3 cement and Coarse Sand of 1.25 finentss modulusbut in Parapet including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cms D.S.R. Item No. 6.13.1

12 mm thk plaster (1:4) with cement & Coarse Sand Ground Floor D.S.R. Item No. 13.4.1

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) D.S.R. Item No. 13.5.1

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R. Item No. 13.80

Finishing walls with Acrylic Smooth exterior paint of required shade :- New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm.). D.S.R. Item No. 13.46.1

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. D.S.R. Item No. 13.45.1

Distemper two coat with oil bound distemper of approved brand manufacture and required shade on decorated wall surfaces to give an even shade over and including a priming coat with cement primer of approved brand and manufacture such as british, shalimar, asian paints after thoroughly brushing surface free from mortar dropping and other foreign matter and also sand prepered smooth including cost of all materials.ground floor (make:Asian/Berger/Dulux)D.S.R. Item No. 13.41.1

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge. D.S.R. Item No. 9.143

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws D.S.R. Item No. 9.21.1

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only D.S.R. Item No. 9.22.1

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating and chemical barrier under and around the columns pits, wall trenche basement excavation top surface if plinth filling junction of wall and floor along the external per meter of binding expension joints surrounding of pipes and conduit ete. Complete (Plinth area of the building at ground floor only shall be measured as per I.S.6313(part ii 1981). Aldrine emulsificable concentrate of any other approved material such as Hepthachlor or chlordance will be used. The rate of application of chemical emulsion shall be as follows. I- Treatment for masonry and foundatrion 5 litres per sqm II- Back fill in immediate contact with foundation 7.5 liters/sqm. III- Treatment of top surface of plinth filling 5 liters per sqm IV- Treatment junction of soil along extemal per meter building 7.50 litre/sqm. V- Treatment of soil under apron along extemal perimeter 5 Iiter/ sqm. DSR Item No. 2.35.3.1

P/L of Brick Coba average 12 cm thick laid with M 150 class brick bat coba 7.50 cm thick with gap of 15 mm to nos other, over 20 mm thick bace of cement morter 1:4 cement and coarse sand mixed with water proofing compound spreading cement siurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1 ; 4 cement and coarse sand mortar finished smooth top mashed faise square 30 cm X 30 cm & side wall parapet shall be monotythic plaster wall upto 30 cm higher & juction & corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished with acitic water proofing compound@ 2 % by weight& including supply of all materials,labours and T&P etc complete for proper completion of the work . rates for 3rd level DSR Item No. 22.7.1

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase D.S.R 2021No 12.21.1

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. D.S.R. 2023 No.12.22

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Make : Kajaria/ Simpolo/Johnson) DSR 8.31

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. DSR 9.76

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. DSR 9.77

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate D.S.R. Item No. 11.3.1

Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required:D.S.R. 1.21.1, 20 mm Dia

Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: D.S.R. 1.21.2, 25 mm Dia

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size 600x1200mm Make: Simpolo D.S.R. Item No. 11.41A.2.2

Antiskid tiles Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 600 mm (Make : Simpolo/Johnson) DSR 11.41A.3.1

Extra for grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm D.S.R. Item No. 11.48.2

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels plain white marble/ udaipiur green marble / zebra balck marble area of slab over 0.50 sqm D.S.R. Item No. 8.2.2.2

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. D.S.R. Item No . 8.5

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi- chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless

steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainlesssteel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. (Make : Fenesta) Two track four panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 8.00 sqm upto 10.00 sqm). sqm D.S.R. Item No. 9.147.A2.2

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm). D.S.R. 9.147.E4.3

6 mm thick clear heat strengthened glass (Make : as provided by Fenesta) DSR 2618

Float glass panes of nominal thickness 8 mm (weight not less than 20.00 kg/sqm) (Make : as provided by Fenesta) DSR 2408

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : All kinds of soil D.S.R. Item No. 2.2.1 1

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). D.S.R. 2023 Item No. 10.28

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) D.S.R. Item No. 4.10

Providing & laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.8

All works above plinth level upto floor V level D.S.R. Item No. 5.33.2.1

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources and using recycled concrete aggregate (RCA) as coarse aggregate and fine aggregate within permissible utilization of 20% each, Portland Pozzolana /Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto Plinth level D.S.R. Item No. 5.33.1.1

Centering and shuttering including strutting, propping etc. and removal of form for : Foundation, footing, bases of columns etc. for mass concrete DSR 5.9.1

Brick work in foundation 1st class b/work in 1:4cement and couarse sand mortar in fdn and plinth incl. supply of all materials , labour and t& P required for proper completion of the work D.S.R. Item No. 6.2.1

Brick work in SUPER STRUCTURE in 23 cm thk wall with 1:4 cement and coarse sand incl. all materials labour annd t&p etc. for proper completion of work. Ground Floor D.S.R. Item No. 6.4.1

S&F Mild steel or iron in plain work such as reinforced concrete and reinf. b/work (when not included in overall rate) wrougt to required shape as necessary Including bending for proper completion of work and incl supply of all steel and wastage and overlapping and hook D.S.R. Item No. 5.22.1

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) D.S.R. Item No. 13.5.1

12 mm thk plaster (1:4) with cement & Coarse Sand Ground Floor D.S.R. Item No. 13.4.1

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.D.S.R. Item No. 13.80

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. D.S.R. Item No. 13.45.1

Wiring for light point / fan point /exhaust fan point/call bell point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc as required.

Group A

Group B

Group C

Wire Sizes

2x1.5sq.mm + 1x1.5sq.mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

SWITCH SOCKET

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing andfixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing andfixing 3 pin 5/6 A modular socket outlet and 5/6 A modularswitch, connections etc. as required.

FAN & LIGHTS

Installation, testing and commissioning of ceiling light 10watt with all accessoriesand including connections

Supplying Installation, testing and commissioning of concealed light box 4inch dia,4inch height and 3mm thick.

Supplying Installation, testing and commissioning of 36W panel light 2feet by 2feet,4inch height and 3mm thick.

Supplying Installation, testing and commissioning MIRROR LIGHT (MAKE- IMPERIAL) (6W) with all accessories and light,including connections

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factornot less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

GEYSERS

Supply, installation, testing & commissioning of 3 liter 4.1 star instant water heater (Gyser) with all accessories. Wattage 3000W (make crompton).

Supplying and fixing following way ,single pole & neutral ,sheet steel,MCB distribution board ,240V on surface recess, complete with tinned copper bus bar ,neutral bus bar,earth bar,din bar,interconnections,powder painted including earthing etc as rquired .(butwithout mcb/rccb/isolator)

Supplying and fixing following ways surface/recess mounting ,vertical type,415v ,TPN MCB distribution board of sheet metal,dust protected,duly powder paint,inclusive of 200A tinned copper bus bar,common neutral link earth bar ,din bar mounting MCBs(but without MCBs and incomer) as required.(note vertical type MCB TPDB is normally usedwhere 3phase outlets are required

Single pole

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioninq etc. as required.

METRE

SANITARY APPLIANCES

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400mm

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

N TRAP

Multi trap

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

With Sewer bricks conforming to IS : 4885

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5cm with perforated cover

Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 cement: 5 fine sand 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering required, cutting holes in walls and making good with brick work in cement mortar 1:4 (1 cement : 4 coarse sand) plastered with cement mortar 1:3 (1 cement :3 coarse sand) on inside of the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 cement : 1 fine sand) joints between sand cast iron tee and S.W. pipe, making required channels complete as per standard design and specifications

150mm dia sand cast iron drop connection

Providing and fixing C.P. brass angle valve for wc, basin & geyser of approved quality.

Providing and fixing 8 mm dia C.P. / S.S. Jet/ health Faucet with flexible tube upto1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer iCharge.Concealed work, including cutting chases and making good the walls etc."

15 mm nominal dia Pipes

25 mm nominal dia Pipes

"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer iCharge.Concealed work, including cutting chases and making good the walls etc."

15 mm nominal dia Pipes

metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and as per direction of Engineer in Charge. Internal work - Exposed on wall

Transportation of Boaring Material Submersible Pump, P-Grevel, Vintonite Powder, PVC Pipe, Boaring Machine etc.

per ltr

150mm dia deep Boaring by deep bore machine

Supply of 125mm PVC Pipe (8Kg)

Supply of 32mm UPVC Column Pipe ISI Mark. (3mtr)

Supply of Submersible Pump 2HP ISI mark.

Supply of Starter with Pannel Board

Supply of 4mm Cable

Supply of P-Gravel

Supply of Vitonite Powder

Water arrangement for boaring

Loaring of 125mm PVC Pipe

Threading in PVC Pipe

Cleaning of boaring