ADDITION/ALTN OF BATHROOM OF (BLDG NO H 24) GUARD ROOM AT MH SHILLONG PROVN OF NEW TOILET BLOCK FOR (BLDG NO D 3 L) AT LOWER BLOCK MH SHILLONG, ADDITION ALTERATION IN SINGLE JCOS LIVING ACCOMMODATION (BLDG NO H 2 3 F 4) AND BLDG NO H 2 3F 3) AT UPPER

Amount

Excavation over area n.exc 1.5m wide and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed

Excavating over areas, n. exc 1.5 m deep and getting out soft/disintegrated rock complete all as specified and as directed.

M&L for PCC (1:4:8) type D-2(using 40mm gr aggregate) in foundation, filling and mass concrete complete all as specified and directed

M&L. for Walling of Random rubble, uncoursed , polygonal rubble walling brought up to course built in cement mortar (1:4) complete all as specified and directed

M& L for returning and filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and directed

Removing excavated material/ surplus soil and depositing where directed at a distence not exceeding 50mtr.at a level not exceeding 1.5 mtr from starting point complete all as specified and as directed.

M&L for removing excavated materials (soil) exc 50 m and n.exc.250m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed

M & L for removing of excavated soil to a distance exc 250m but n exc 500m and deposited where directed n exc 1.5 m above the starting point complete all as specified and as directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggreagtes) including necessary form works as in precast bond stone set in CM (1:6) complete all as specified and directed

Extra over Hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 20mm in granite or trap stone complete all as specified and directed

M&L for raised pointing to random rubble stone masonary uncoursed or brought upto course in cement mortar (1:3) complete all as specified and directed

M&L PCC coping (1:2:4) type B-1 (using 20 mm graded aggregate) complete all as specified and directed

M&L for loose filling with aggregates of guage 80 to 150mm broken stone or boulders behind weep holes complete all as specified and directed.

M&L for hard core of broken stone or boulders of guage not exc 63mm deposited spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for excavation in foundation trenches n.exc 1.50m wide and n.exc 1.50m in depth and getting out in soft /loose soil complete all as specified and directed

M&L for RCC 1:1.5: 3 ( nominal mix) using 20mm graded stone aggeregate in foundations, including rafts, footings , plinth beams, bases for columns etc complete all as specified and directed

M&L for RCC 1:1.5: 3 ( nominal mix) using 20mm graded stone aggeregate in columns,pillars ,piers posts complete all as specified and directed

M&L RCC 1:1.5:3 (Nominal mix) using (20mm graded aggregates ) as in beam, lintel band over 1.50m span complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beam , lintels , cantilevers , shelves including supports , overhangs etc. also splays between floors and beams etc rough finished concrete surfaces complete all as specified and as directed..

M&L for formwork to sides of concrete foundations,footings, bases of columns, plinth beams and similar work with rough finish surfaces of concrete flat complete all as specified and directed.

M&L for formwork to sides of pillars, posts,struts,piers , columns and like with rough finish surfaces of concrete flat complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally in stirrups with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade ST-240 complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L for preparation of new wall surafces and applying two finishing coat of acrylic emulsion paint , anti fungal resistance , dirt resistance exterior paint of required shade including primer coat on new surfaces complete all as specified and directed.

M&L for 100mm thick cement concrete using (40mm graded aggregate) type D-2 (1:4:8) as in sub base complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with gray cement and pigment in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 18/20mm thk granite slab ( as in table top rubbed and polished) as in wall lining 12 mm thick in CM 1:3 , pointing in white cement 1:2 using granite dust with admixture of pigment to match complete all as specified and directed.

Demolition of concrete of any description in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM (1:6). complete all as specified and directed.

M&L for Glazed ceramic colour tiles in vertical surface of size 350x250x7mm/450x350x7mm / 600 x300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour including rendering in CM (1:4) 10 mm thick for vertical faces in complete all as specified and directed.

S&F Vitreous china wash down water closet pan padestal pattern white, excluding fixing bolts, flushing cistern but including flush pipe, seat and cover complete all as specified and as directed.

S&F PVC valveless, 10 ltrs, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs vitreous China clay WHB flat back size 450x300 mm incl pedastal , PVC waste pipe 32 mm dia, waste coupling brackets etc complete all as specified and directed.

S & F Brass CP tubular towel rail 20 mm dia , 60 cm long including brackets complete all as specified and directed.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railling 60 cm long screw and cup washer complete all as specified and directed.

S&F in repairs 15 mm bore CP health Faucet with Flexible pipe 1 m long of make Jaguar Cat Part No:ALD-565 or equivalent in marc/parryware/prayag

S&F in repairs CP Soap dish holder of make Prayag Cat Part No:-BA-05 or equivalent in marc/parryware/prayag

M&L for 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius with access door complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius with access door complete all as specified and directed.

S&F PVC (SWR) 75mm bore vent cowl complete all as specified and directed.

Dismantling water tanks exc 500 ltrs but not exc 1000 ltrs capacity , complete all as specified and directed.

Supply and fixing rotational moulded HDPE water storage tank ,double layer ,ISI marked (cylendrical vertical type with closed top) of capacity 500 ltrs in position incl float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

M&L for cutting chases,pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing steps, cills, sunshades ,shelves,lintels,etc.; and cutting chases for concealed water tubing or concealed conduit,wiring,etc,and making good cutting not exceeding 10 cm girth in brick walls. complete all as specified and directed.

S&F in repair 15mm bore CP fancy type concealed stop cock, with long shank and cup all as specified and directed

S&F PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 15 bore Bib taps, cast copper alloy fancy type , chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F Grating doom 100 mm dia of PTMT.(Minimum weight 25 gms) and jointing with solveent cement complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections of 20 mm bore complete all as specified and as directed.

S&F G.I. pipe 15mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors complete all as specified and as directed.

S&F G.I. pipe 20 mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid blocks exc 10 cm in width with PCC (1:3:6), type C-1, (using 20mm graded stone aggregate) and setting in CM(1:6) complete all as specified and directed.

M&L for precast cement concrete block massonry with solid blocks nexc 10 cm in width and settings in CM 1:4 type C1 1:3:6 (20mm graded aggregate) complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement all as specified and directed

M&L for 15mm rendering in cement mortar (1:6) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of new walls surface and applying two coats of distemper oil emulsion over a coat of 1 mm thick wall care putty and one coat of wall primer and complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) and mixing with WPC @ 3% by weight of cement finished even and smooth without using extra cement all as specified and directed Note : WPC shall be measured & paid seperatly as supply only.

Supply only Integral water proofing compound

M & L for complete removal of existing treatment of walls including cornices, pilasters etc and applying two coats of distemper oil emulsion over a coat of 1 mm thick wall care putty and one coat of wall primer and complete all as specified and directed.

M&L for for applying two or more coats (over 1 mm thick plaster of paris wall care putty) of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, Alkali & fungal resitance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surface on new or previously untreated surfaces complete all as specified and as directed.

M & L for preparation of new walls surface and two coats of white wash complete all as specified and directed.

M& L for excavation in post holes (or similar holes) each in any type of soil n. exc. 0.5 cum, getting out, returning filling in an ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm, watering and removing surplus soil to a distance not exc. 50 M and making good complete all as specified.

M&L for Mild steel joist channel or angle or tee section,ms tube and fixed with ms flat iron cut into shape drilled and fixed with screw conforming fe 410 grade complete all as specified and as directed.

Taking down chowkats but with shutters (without taking off shutters from frames) exc 1.5 Sqm but n exc 4 Sqm each complete all as specified and directed..

Taking down chowkhat with shutter (without taking off shutter from the frame) and area n exc 1.5 sqm each complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed togeather with solvent cement, fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, supplying & fixing in openings as per specification complete all as specified and directed.

S&F ,2nd class hard wood plain soild, straight chowkats and frames, wrought, framed rebated on thesolid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 30 mm thick 2nd class hard wood flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F 30mm thick 2nd class hard wood skelton shutters open rebated and prepare to receive glass, gauze, etc but divided into squares with planin chamfered or rounded , mitred , rebatad sash bars complete all as specified and directed

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm complete all as specified and as directed.

M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) 200mm size and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) 300mm size and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm complete all as specified and directed.

S&F aluminium anodised barrel bolts and fixed of 200 mm length complete all as specified and directed.

S&F Extruded Aluminium, anodised, bow handles of size 150mm complete all as specified and directed.

M&L for barass tower bolt, of size 75mm stove enamelled black with bright bolt complete all as specified and as directed.

M&L for Bow Handle, brass type of size 100mm complete all as specified and as directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 75mm complete all as specified and as directed.

S&F powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

S&F powder coated (powder coating min 50 micron) anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for old steel surfaces of any description exc 10 cm in width or girth when unconnected with other painting surfaces with one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete 1:3:6 type C2, 75mm thick as in plinth protection finished even and smooth with out using extra cement complete all as specified and as directed.

M & L for PCC 1:3:6 C2 (40 mm graded aggregate) as in surface channels and drains all complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms,moulds,mitred/ stop ends complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description over 10cm in width or girth and treated with one coat of synthetic enamel paint complete all as specified and directed.

M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pan complete all as specified and as directed.

Dismantling of plain/corrugated steel sheeting any gauge, thickness in roof covering complete all as specified and directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F pre painted galvatume aluminium zinc coating GI based plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

S&F 2nd class HW boarding 20mm thick fixed with nails in eaves board plained one side with butt joint complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm over in section in any position (unframed work) complete all as specified and as directed.

M&L for 2nd class hard wood in scantling clean sawn timber fixed complete all as specified and as directed.

Dismantling wrought Iron or mild steel work of any description not other wise described complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with gray cement and pigment in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/above ground level) all as directed.

M&L 25 mm thick cement concrete using (20mm graded aggregate) type B-1 (1:2:4) as in sub base complete all as specified and as directed..

M&L for vitrified ceramic tiles dark shade, 10 mm thick(square /rectangular), polished, area of each tile n exc 0.36 sqm in floor etc , laid over 15 mm thick screed bed in CM 1:6 ,set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified.

All as per item No115 but on vertical surfaces over including 10mm thick rendering in CM1:4

S&F , Vitreous china squatting pan, 'Orrisa Pattern" size 580x440mm white, with integral foot rests (excluding flushing cistern & flush pipe) complete all as specified and as directed.

S&F vitreous China clay WHB flat back size 550x400 mm incl pedastal , PVC waste pipe 32 mm dia, waste coupling brackets etc complete all as specified and as directed.

S&F Vitreous china urinals,bowl type (Back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets flush pipe, grating and union for discharge pipe.(Excluding of fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and as directed.

Supply and fixing rotational moulded HDPE water storage tank ,double layer ,ISI marked (cylendrical vertical type with closed top) of capacity 1000 ltrs in position incl float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

M&L for applying two or more coats ( over 1mm thick plaster paris wall care putty) of 100% premium acrylic emulsion paint having VOC less than 50gm /ltr and UV resistance as per IS 15489 :2004 , Alkali & Fungal resitance , dirt resitance exterior paint of required shade ( company depottinted) with silicon additives @ 1.43 litre /10 sqm over and including priming coat of exterior primer applied @ 0.90 litre /10 sqm over existing surfaces complete removal of existing treatment all as specified and as directed

E/M PART - II SCHEDULE Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, in PVC Casing capping on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately .

Description all as per Srl item No.119 above but for one bell point controled by one bell push .

Description all as per Srl item No.119 above but for socket outlet point 5 Amp on same board.

Description all as per Srl item No.119 above but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 119 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fix switch piano (ISI marked) Single pole 240 volts, 5Amps all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fix bell Push (ISI marked) Single pole 240 volts, 5Amps all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fix socket (ISI marked) 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed. Make- Havells/anchor/ Legrand.

Supply and fix switch socket combination (ISI marked) 2/3 pin and 5/15 Amps, flush type, 240 volts complete all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified. Make : Cona , Plaza, Anchor .

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fixing LED batten fittings 1x18 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable one complete all as specified and as directed

S & F wall mounted LED batten fittings with all accessories 1X 9 Watt LED / foot light 6000K , extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed including taking down old unserviceable light fittings

S & F wall light fittin (Florette) Alabaster glass for diffured light effect, recommended to use with energy saving lamp and synchonised design concept with 4 watt complete with necessary connection compelete all as specified and as directed Make- Havells Item code- LHFOAIC1TZ11010

Supply and fixing of hot water Geysers of 25 ltrs capacity 5 star rated vertical type includng fixing of bolts , nuts grouted into the wall , and necessary cement work , making good of disturbed surface of wall , giving electric and water connection and testing after installation. Make : Havells cat part no - GHWCAMTWH025 : /LG/Ronald.

S&F heat resistant PVC connection pipe for hot and cold water 450mm long 15mm dia. Make: Prayag or equivalent in Polytuf/ Havells/ Sona.

S & F Exhaust fan 230 volts , 250mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall complete all as specified and as directed Make Bajaj/Havell's/CG.

Supply and fixing LED security Building light LED 25 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and as directed.Make Make:- Bajaj Cat part No- 169821 LED/CG as perr vat No LSTO 25 CDL equivalent model as in Surya / havells .

Supply and fix in repairs MCCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified and as directed. (Note : MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable .

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

Supply and fix MCCB TPN, 240 Volts, 40 to 63 Amps, 10 kA rupturing capacity415 Volts complete all as specified and directed including taking down old one.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one. Make: Havells Cat part No - DHMCCDPF006-032 or equivalent in Schnieder/GE/C&S.

Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's.Make : Hager as per cat part- NCN106N, Schneider as per cat No : A9N4P32C or Indoasian as per cat No : 81195 .

M & L for sub main wiring with two runs of single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including PVC Casing / capping, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 6 sqmm as PVC cable and one run of 6 sqmm as earth wire cable and one run of PVC casing / capping shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

M & L for sub main wiring with two run single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including PVC Casing / capping ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 4 sqmm as PVC cable and one run of 4 sqmm as earth wire cable and one run of PVC casing / capping shall be measured as one RM.

Supply lay/spread in trenches , river sand ,clean ,including spreading ,levelling ,punning for laying /cushioning of cables all as specified and as directed.

Supply lay in trenches fly ash bricks, old size sub class “B” for cable protection complete all as specified and as directed

Supply, lay in trenches, floors ,fix on wall/pole, passing through pipes etc.,LT UG cable , 1100 volts grade, PVC/ XLPE insulated , with multistranded aluminium conductors, armoured with galvanised steel wire or tape ,gland, lugs etc , of size 16 Sq.mm 4 core , confirming to IS specifications complete all as specified and as directed

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as specified and as directed

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III Note (All chases will be cut by chase cutter only) AMke of Cable - KEI/ Havells / Kalinga

Description all as per Srl item No148 above but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 148 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fixing modular switch 1 way 6 A module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. Make : Cona , Plaza, Anchor, Vinay

Supply and fixing modular switch 1 way 16 A module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. Make : Cona , Plaza, Anchor .

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. ake : Cona , Plaza, Anchor, Vinay

Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. ake : Cona , Plaza, Anchor, Vinay

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type, warm white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete pre wired fixed to wall with 2 nos PVC block of suitable size complete all spcifided and directed.

S & F Mirror wall mounted LED batten fittings with all accessories 1X 12 Watt LED 6000K , warm white / white type extruded polycarbonate, integrated electronic driver and fixed to wall complete all as specified and as directed including taking down old unserviceable light fittings Make- Philips cat Part 31403 12-Watt LED picture Light (Gold)

S & F Wall bracket decorative LED fitting 2 light opal glass with chrome finishing warm white /white type with lamp 12 Watt complete with necessary connection complete Make- Jaquar Cat part KCH-CHR-MB160275532B

S & F Exhaust fan 230 volts , 300mm, heavy duty steel body including making all electric connection complete all as specified and as directed including cutting of hole on wall and making good disturbed surface of wall and outer wooden box for fan fix on wall including taking down old one Make Bajaj/Havell's/CG.

S&F lamp holder, insulated body, with back plate for batten fitting complete. Make- Havells/anchor/Legrand.

S&F bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F angle stop valve cast copper alloy, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixing of size 15mm.

S & F single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB complete all as specifided and as directed

M & L Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion including taking down old wiring etc complete all as directed. Note: (i) Two runs of 4 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

M & L Sub main wiring with two run single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM.

Supply and fixing Flexiable cable 6 Sqmm Weather proof single flat twin core cable including pvc pipe 20 mm dia clmple nut bolt fixing in tracnh/wall/sarface area etc. complete all as specified and directed

S & F Slim desingn LED recessed round/square type down lighter 12 watt warm white / white type flat panel PDC aluminium housing and PMMA diffuser including taking down old unserviceable one all as directed and specified Make- CG Cat Part No- LCDEP-12-WW

R K CONSTRUCTION

KB Singha and Associates

S K Construction

M/S K.B.VENTURES PVT LTD

M/s A L Traders

M/s Nishi Kumar Das