SPL REPAIR TO BLDG NO P-34 OF E ARTY REGT, BATH OF BLDG NO P-01 OF D ARTY REGT, PROVN OF FALSE CEILING AND NECESSARY ARRANGEMENT IN EXISTING SHED OF RELIGIOUS INSTT AND CONSTR OF 01 X PARKING SHED NEAR ADM BLOCK, HQ 24 RAPID AT MIL STN BIKANER

of 10mm dia rod fixed with and including standard aluminium frame of 'F' section of size 23.4x15.3x1.4 mm thick all as per manufacturer's instructions complete and as directed by Engineer in charge.

M&L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and directed.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 4 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete and as directed by Engineer in charge.

M&L for Preparing new plastered or unplastered surfaces of ceiling and applying two coats of white wash over 2mm wall putty , white or tinted complete and as directed by Enginner in charge.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick wall care putty on new surfaces including preparation and complete specified and as directed by Engineer in charge.

S & F MCB SPN, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

Earthing complete with galvanised perforated steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 6mm dia galvanised iron or steel wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -2 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement using integral liquid water proofing compound and complete and as directed by Enginner in charge. Note : WPC shall be measured and paid seperately.

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 2 mm thick putty complete and as directed by Engineer in charge.

Ditto all as per item No 12 above but on vertical surface over and including 10mm thick rendering in Cement mortar 1:4 complete all as specified and directed.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting on 15mm thick screeding in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

M & L for glazed ceramic tiles (coloured) 450x300x7mm thick on vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick rendering in Cement Mortars 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for demolition of sunken filling concrete, removal of loose concrete and cleaning the surface and after proper cleaning filling the cracks with polymer modified mortar using Dr fixit pidicrete URP and providing 50mmx50mm angle fillets on the vertical upstands, parapet wall junction corners, service units and properly dressed by preparing polymer modified mortar with DR Fixit pidicrete URP in the ratio of 1:3 by adding polymer 10% by weight of the cement, add the water little little unit the required consistency is achieved and thereafter providing and applying two coats of acrylic polymer modified cementitious coating Dr Fixit pidifin 2K of M/s Pidilite Industrieshaving elongation at break 50% 5 bar resistance to positive water pressure, Adhesive strength ASTM D 7234-1 N/mm sq, water vapour transmission as per ASTM E96 of 030 perms and crack bridging ability as per EN 1062-7 upto 1 mm. Apply two coats of Dr Fixit pidifin 2K slurry “ coverage of 0.55-0.58 Sqm/kg of mix slurry. Provide and lay 45 gsm glass fibre mesh over the angle fillet when the first coat is still wet. Allow the first coat to dry for 6-8 hours, then apply the second coat at a direction perpendicular to first coat. Allow the coating to air cure for 5 days before conducting water ponding test for 24 hrs etc or other equivalent product as approved by GE in sunken area complete all as per the manfactures instruction, including removing rubbish material from building and thrown in low lying empty area at any distance out side MD land complete all as specified and as directed by Engineer-in-Charge

M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand even and smooth with steel trowel on sunken surfaces using integral water proofing compound.( WPC shall be measured and paid separately)

S&F in repair vitreous china wash down water closet pan with fixing bolts, trap (pedestal pattern), white, (excluding flushing cistern and flush pipe) complete fixed in repairs as directed by engineer in charge.

Supply only liquid water proofing compound ISI marked @ 200ml per 50Kg of cement content complete and as directed by Engineer in charge.

Dismantling of floor hearth or existing terrazo dado /flooring or tilles in bath .WC and kitchen etc complete and as directed by Engineer in charge.

M&L light coloured Vitrified Ceramic tiles 10 mm thick (square /rectangular) area of each tile not exceeding 0.36 sqm, in floors over 15mm thick screeding in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete as specified and as directed by Engineer in charge. (Adhesive shall be measured and paid separately)

S & F in repair PVC valve less, symphonic action type, flushing cistern (10 liters capacity)

low level, white, with inlet, ball valve, float and handle including brackets complete and as directed by Engineer in charge.

S&F Vitreous china wash basin, white, flat back, size 550 x 400mm, including brackets and cutting for and pinning in ends of brackets, fixed in repairs complete and as directed by Engineer in charge.

S&F single lever central Hole Basin Mixer 15mm bore dia with letter marked for cold and hot complete and as directed by Engineer in charge.

S & F in repair brass chromium plated bib cock long Nose body Fancy type with capstan screwed down for iron pipe 15 mm bore complete and as directed by Engineer in charge.

S & F in repair angle valve cock chromium plated fancy type half/full turn for iron pipe 15 mm bore screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete and as directed by Engineer in charge.

S & F in repairs for Brass chromium plated High flow diverter including upper part of diverter, spout, hand(mobile) shower 100mm with 1.5meter shoer faucet set complete and as directed by Engineer in charge.

S&F 32 mm bore stainless steel bottle trap set with waste outlet pipe for wash basin/Kitchen sink with coupling complete and as directed by Engineer in charge.

S & F repair PVC connection 15 mm size brass nuts of length 450 mm complete and as directed by Engineer in charge.

Taking up or down steel tubing and connections 15 mm bore complete all as specified and directed by Engineer in charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete and as directed by Engineer in charge.

Supplying and laying of CPVC pipes of 20 mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wall((100mm away from wall using sutaible clamps) complete and as directed by Engineer in charge.

Supplying and laying of CPVC pipes of 25 mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, walls(100mm away from wall using sutaible clamps) complete and as directed by Engineer in charge.

S&F CPVC 20/25mm male/female brass threaded adaptor(FTA/FBTA) complete and as directed by Engineer in charge.

Dismantling cast iron pipes of any description any dia all as specified and directed by Engineer in charge.

S&F 110mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint laid in trenches or in floors complete all as specified and as directed by Engr-in-Charge.

S&F 110mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint fixed to wall(100mm away from wall using sutaible clamps) complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint fixed to wall(100mm away from wall using sutaible clamps) complete all as specified and as directed by Engr-in-Charge.

S&F CPVC Union 20/25 mm complete and as directed by Engineer in charge.

S&F in repair triple layer Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, hoisted and fixed in position including connecting up pipes complete and as directed by Engineer in charge.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms) complete and as directed by Engineer in charge.

Taking down eaves gutters and rain water PVC pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc (measured overall as fixed along the centre line over fittings and accessories) complete and as directed by Engineer in charge.

S&F PVC(SWR) bends,110mm. Bore complete and as directed by Engineer in charge.

S&F 40 mm PVC single pipe socketed waste and vent pipe in any length including bend, reducer joint with solvent fixed to wall, in floor complete all as specified and as directed by Engr-in-Charge.

S&F 110mm. Bore PVC (SWR) junction single,(Single T) equal or unequal with access door complete and as directed by Engineer in charge.

M&L PVC(SWR) floor trap 75mm incl.CP grating jointing with solvent complete and as directed by Engineer in charge.

S&F PVC (SWR) 110mm to 75mm reducer complete and as directed by Engineer in charge.

S&F 75 mm PVC (SWR) vent cowl complete and as directed by Engineer in charge.

S& F chromium plated soap dish Holder with round flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer in charge.

S & F in repair gun metal glob or gate valve with iron wheel head , crewed for iron pipe of 20 mm dia fixed in repair complete and as directed by Engineer in charge.

S&F in repairs Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete and as directed by Engineer in charge.

S&F Tubular towel rail, 20mm dia, D type, 60cm long between flangess complete and as directed by Engineer in charge.

S&F Factory made Double extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 65 x 150 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, ater/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) skeleton door solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, ater/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Supply and fixing 100mm long stainless steel butt hinges heavy duty including steel screws for fixing complete all as specified and as directed by Engineer-in-charge.

S&F Corner glass shelf of size 300mmx200x150mm fancy type, toughned glass, with CP bracket and guard railing, fixed along wall with CP brass screws and PVC plug complete and as directed by Engineer in charge.

M&L for 25mm dia stainless steel chromium plated curtain rod incl bracket & knobs fixed in position complete and as directed by Engineer in charge.

Taking down window/chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each complete and as directed by Engineer in charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete and as directed by Engineer in charge.

S&F stainless steel sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed and complete and as directed by Engineer in charge.

S&F stainless steel barrel tower bolts of extruded section 200 mm long complete and as directed by Engineer in charge.

S&F stainless steel barrel tower bolts of extruded section 150 mm long complete and as directed by Engineer in charge.

S&F stainless steel handles cast type anodised, 125 mm size complete and as directed by Engineer in charge.

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete and as directed by Engineer in charge.

S&F 18 mm thick single side prelaminated wood grain solid PVC sheet suitable fxed in shelves, cupboards, partitions and shelves of built-up cupboards, for kitchen with 6 mm PVC beading support , washer, plug, Handles, Knob , magnets, locks etc complete all as specified and as directed by Engineer-in-Charge.

S&F 125mm Aluminium handles, cast type,anodised complete.

M&L for preparation of old interior surface of walls including complete removal of existing treatment by mechanical equipment like electric sander and applying two coats of oil bound distemper over 2 mm thick putty complete and as directed by Enginner in charge.

M&L for Preparing old ceiling including complete removal of existing treatment by mechanical equipment like electric sander and and applying two coats of white wash over 2mm wall putty , white or tinted complete and as directed by Enginner in charge.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including complete removal of of existing treatment complete specified and as directed by Enginner in charge.

Demolition of lime concrete of any description over roof slab complete and thrown away at specified location all as directed by Engineer-in-Charge.

M&L for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and complete and as directed by Engineer in charge.

Supply only 5mm thick Figured glass, pin head type and glazing with beads (either supplied with shutters or to be measured separately as supply only) in squares not exceeding 0.5 Sqm in each pane complete and as directed by Engineer in charge.

M&L for roof treatment in as specified below and as directed: (a) cleaning, washing of surface and removing any debris, Surface should be free from any loose paint, dust or grease (b) Applying one coat of Elastomeric PU based liquid membrane diluted with portable water in the ratio of 1:1 and apply @ 0.40kg/sqm (c) laying polyster reinforced fiber Net/50 Gsm Geotextile mese, upto 300 mm on walls. (d) Applying two coats of undiluted PU based liquid membrane, having elongation more than 400 %, tensile strength more than 2 N/mm2 and alkali & fungal resistant maintaining thickness of 1.5mm, with brush/roller upto 300mm on walls. (e) That complete treatment to be carried out by authrised applicator of waterproofing manufacturer. Make : Asian/fosroc/Dr fixit etc. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer-in-Charge.

Supply only 4.80mm thick Sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete and as directed by Engineer in charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with 40mm width of flaps (when open) and complete and as directed by Engineer in charge.

S&F 100mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete and as directed by Engineer in charge.

M&L Providing, cement concrete in roof Type B0 1:2:4 using 12.5 mm graded aggregates as in PCC Bed and complete and as directed by Engineer in charge.

M&L for 10 mm thick screed bed in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only) complete and as directed by Engineer in charge.

Demolition of brick work built in cement mortar including all quions arches pillars etc complete and as directed by Engineer in charge.

M&l for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6. complete and as directed by Engineer in charge.

Demolition of cement conc. Reinforced as in staircase , beams chhajas and similar suspended work reinforced cut required to facilitate demolition complete and as directed by Engineer in charge.

M&L RCC Design Mix of M-25 slab supported on walls beam and column in floor roof landing and like using 20 mm graded stone aggregates and complete and as directed by Engineer in charge.

Structural design for Existing Roof Slab, Beams, Chajja, staircase and other connected RCC members required to be re-constructed under this Schedule with & including vetting of structural design from approved Govt Engineering College/NITTTR/CBRI, complete all as specified and as directed. Notes : (i) Tenderer shall carryout the site visit to ascertain the size of slab, other RCC members, arrangement of rooms, etc required for design purpose.(ii) Four sets of Structural drawings shall be provided to GE by the contractor duly vetted as above as directed by Engineer in charge.

M&L RCC Design Mix of M-25 Grade for chajja and like using 20 mm graded stone aggregates and complete and as directed by Engineer in charge.

Form work to soffits of suspended slab such as roof slab not exc 200 mm thick to rough finished surface of concrete complete and as directed by Engineer in charge.

S&F for Special shaped design factory made tubular or square pipes, semi circular type factory made steel truss work, one side 5 mtr-6 mtr cantilever type and 2 sides 10 mitr-12 mtr cantilever type including centre gutter channel support work for water outlet,purlins,rafters,etc complete conforming to IS 1161-1979 grade St.-240 (Shed design to be provide by Engr in charge) prepare by as per design complete all as specified and directed by Engineer in Charge.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to GDE of Fe 410-W or Fe310-O, complete all as specified and as directed by Engineer in Charge.

S&F for mild Steel work confirming to Fe-290 Gde E-165 in wind ties fo

Form work to chullah hoods, chajjas, troughs and similar items including edges to rough finished surface and complete and as directed by Engineer in charge.

M&L for Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete and as directed by Engineer in charge.

r roof including securing bolts and necessry drilling, bolting or riveting etc. complete all as specified and as directed by Engineer in Charge.

M&L for Mild steel TMT bars8- 10mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete and as directed by Engineer in charge.

Excavation in post holes (or similar holes) in soft/loose soil, each not exceeding 0.50 cum and getting out, returning, filling in and well ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, including watering and removing surplus soil to a distance not exceeding 50m away from the starting point and making good surfaces complete and as directed by Engineer in charge.

Material and labour for PCC (1:2:4) type C-2, (using 40mm graded stone aggregate) as in foundation, mass fillings for posts/struts etc. complete and as directed by Engineer in charge.

S&F Mild steel screw bolts (machine made) any dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete and as directed by Engineer in charge.

M&L for preparation of new steel surfaces exceeding 10 cm with or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer in Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel roof sheet 0.50 mm thick of any colour having tensile strength of 550mpa as in roof sheet/covering/ridge /gutter/cladding to wall etc, fixed with self drilling screws complete all as specified and as directed by Engineer in Charge.(Sheet to be use in cantilever type parking shed) complete and as directed by Engineer in charge.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete and as directed by Engineer in charge.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete and as directed by Engineer in charge.

Hardcore of broken stone or boulders of gauge n exc 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete and as directed by Engineer in charge..

M&L for 25mm thick sand filling under floors, cushning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm thick PCC(1:4:8) type D-2 using 40 mm graded stone gregate as in sub base of floor finished even and rough complete and as directed by Engineer in charge.

M&L 60 mm thick factory made coloured mixed with pigment precast concrete interlocking paver block of grade M-35 confirming to IS 15658-2006 manufactured by vibratory process laid over sand cushioning complete and as directed by Engineer in charge.

M&L preperation of new decorative concrete, plastered/ un-plastered surface and applying two coat of cement based paint of any tint complete all as specified and directed by engineer in charge .

M&L for cement concrete 1:2:4 type B-0 using 12mm graded stone aggregate in coping, plinth course, parapets or roof kerbs ,rounded or chamfered on edges and ramp concrete including necessary form work complete and as directed by Engineer in charge.

S & F 10mm thick Plain PVC sheet fixed with screws in false ceiling grid made of G.I including joint filling material complete all as specified and directed by Engineer-in-Charge

M&L for rendering 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface in ceiling finishing the surfaces even & smooth without using extra cement using integral liquid water proofing compound complete all as specifie and directed.NOTE: WPC shall be measured and paid seperately.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in radius built in CM(1:6) complete and as directed by Engineer in charge..

M&L for Preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of primer with roller , white or tinted complete all as specified and as directed by Engineer-in-Charge.

M&L for 15 mm thick cement rendering in CM(1:4) finished even and smooth without using extra cement complete and as directed by Engineer in charge.

S&F pre-painted galvalume aluminium zinc coating GI bared corrugated steel roof sheet 0.50 mm thick of an column having tensile strength of 550mpa fixed with self drilling screws complete all as specified and as directed by Engineer in Charge.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete and as directed by Engineer in charge..

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete and as directed by Engineer in charge.

(b) One pin 5 amps socket point on the same board with other switches complete and as directed by Engineer in charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,hinges, handles, sliding bolts & tower bolts all complete as per architectural drawings complete and as directed by Engineer in charge.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6m mean radius built in Cement and Sand Mortar (1:4) complete and as directed by Engineer in charge.

S&F Mild steel Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc Fe 410-W(Gde E- 250) quality A complete and as directed by Engineer in charge.

S&F Powder Coated aluminium grill of design DG-104 pattern, made out

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F Sheet glass, ordinary quality and glazing with oil putty in each panel of thickness 4.8 mm but exc 0.5 sqm complete all as specified and directed.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F of bell push, modular type 5 Amps 1 module complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engr-in-Charge.

S&F LED Bulb 9W, operating voltage- 220-240 volts, starting time < 0.5s, color temperature-6500K, lumens: min 825 complete all as specified and directed by Engineer-in-charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-Charge.

Supply and fixing LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-charge.

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Supply and hanging/fixing ceiling fan 1200mm sweep AC supply (input voltage range 120 to 280v), BLDC type, 5 star rated BEE and ISI marked, super enameled copper winding of 'B' class insulation, single phase 20 watt (+ 10%), PF 0.90 (MIN), air delivery of 220 CUM per min (CMM), 350 RPM (+ 10%), TEMP RISE 40 DEGREE MAX, without remote, with electronic regulator, 3 blades, down rod length of 60/72 inch including accessories, total harmonic less than 10%, 5 speed, hanging in position, including making connection wih and including flexible cord twin core twisted copper conductor of size 23/0.0076 from cealing rose to fan complete all as specified and as directed. Note :- (i) Sl No of cealing fan and GE office name shall also be writing on fan with red colour permanant marker. Cost for the same shall deemed to be included in quoted unit rate. Nothing shall be paid extra on this account.

Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50 Cycle per second, size 300 mm sweep with blades and frame including new GI wire mesh heavy duty with wooden frame protection against birds etc including provision of cutting of existing wall for suitable opening as per fan, including electric connection with and including new 1 Sqmm, 2 core flexible copper conductor cable from ceiling rose to fan, fan hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB 12 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SPN 40 to 63 Amps, 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S&F in of sheet metal enclosures with socket, plug top complete with one single pole MCB -240 Volt- 20 AMP complete all as specified and as dircted by Engr-in-charge.

S&F Electric bell Ding Dong AC 230 volts single pole complete all as specified and directed by Engr-In-Charge.

S & F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve,thermostate,NRV ,TOP PLUG 20AMP with valve flange suitable for 15mm bore pipe for water supply connection complete. Make : Havells (Model -Monza EC) Cat part No GHWAMFSWH025/Bajaj calenta storage/Cromton solarium Qube

Supply and fixing LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-charge.

s per electrical plate No -2 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

S&F MCCB TPN DB, 4 WAY verticle type, 440 volts, 3 phase with rated bus bar 200 amps, double door type suitable for MCCB as a incomer and MCBs as outgoing double door type, grouted in walls with fixxing arrangements complete all as specified and as directed by engr-in-charge.Make:ABB/Legrand/C&S

Per Point

S & F MCCB 63 Amps,4 pole, 415 volts,overload and short circuit adjustable type breaking capacity 25KA complete all as specified and as dircted by Engr-in-charge.MAKE : ABB/Legrand/C&S

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m wide for laying of UG cable / pole etc and getting out including forming bottom surface to required level and gradient in soft/dense soil complete all as specified and as directed.

S7F in replacement of LED decorative post top lantern light fittings for 360 degree indirect light with IP 65 protection, resistant to impact and corrosion, glare free and better uniformity. MAKE CG Model LPTO-40-CDL or equivalent make. Phillips/Bajaj.

Returning filling in, excavated soil including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified.

Removing excavated materials/soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.

Supply and fixing GI Pipe light grade of Size 40 mm bore with all fittings for passing of cables fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable all as specified and directed. Make: Jindal/ Bansl/Tata

S&F in replacement Recessed mounting LED 2x2 luminaire type BCTBLR 36W ZTN NW in make BAJAJ or equivalent in CG/Phillips/GE/Wipro/Havelles.

S&F in repairs PVC (SWR) junction single, (single T) equal or unequal any radius, 110 mm bore complete all as specified.

S&F PVC (SWR) vent cowl any radious 75 mm bore complete all as specified.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with head moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rain & bottom rail paneling of plain gap insert for top rail & bottom rail paneling of plain color PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement all as specified

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube suppling & fixing in opening all as specified and as directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S&F 250 mm long sliding door bolt, plate type, mild steel, stove enamelled black with bright bolt of not less than 12 mm dia with & including a minimum of six bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

S&F 100 mm long, Butt hinges, stainless steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing 20 mm dia and connections and stacking neatly for offering credit.

M& L GI Tubing, medium grade galvanised, 15 mm bore with all fittings and fixed to walls and ceilings or laid in floors

M& L GI Tubing, medium grade galvanised, 20 mm bore with all fittings and fixed to walls and ceilings or laid in floors

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 04 core x 25 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells/Finolex Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame or stone concrete or brick surrounds glazed with putty or fixed with beads.

3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not execeeding 0.5 sqm in each pane for metal frames complete all as specified

Dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises.

M&L Non skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

Glazed ceremic tiles coloured 450X300mmX7mm/350x250x7 mm thick coloured, set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.

Dismantling of stone slabs and tiles of any description or thickness in floors/dado etc laid bedded 10 and pointed in any mortar

M & L for Granite (of any type) work 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl edge moulding and machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engineer in Charge.

Demolition of cement conc. In any description and inc any position not otherwise specially provided complete all as specified and directed

M & L PCC 25 mm thick 1:2:4 type B0 (12.50 mm graded aggregate) in any position in ground floor/roof complete all as specified and as directed by engr-in-charge.

S&F in repairs Vitreous China wash down water closet pan (Pedestal p

attern) white complete incl seat and cover, flush pipe incl all joints complete.

S&F health faucet with 1 mtr long tube and hook and knab all as specified and directed by E Engineer-in-Charge

S & F in repair PVC valveless syphonic action type flushing cistern, 10 ltr capacity low level, white with inlet, ball valve, float and handle including brackets fixed in repairs. Cat Part No Cera B1010102.

Supply and fix in repair vitreous china wash hand basin Oval size 560x400x205 mm including cutting for and pinning in ends of brackets or erecting stand etc incl waste fittings complete. Cat Part Cera S2030102.

S&F in repair Stainless steel tubular towel rail, 20 mm dia D type 60 cm long between flanges. Cera Cat Part No F5002103.

M&L in repair Bib tap 15 mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe and fixed in repairs Cat Part No Cera F1005152

M&L in repair Pillar taps, 15mm dia, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, long screwed shanks and fly nuts, screwed for iron pipe and fixed in repairs Cera CAT Part No F1003104

S&F in Brass Soap Dish fancy type complete all as specified and directed by Engineer-in-charge. Cera Cat Part No F5012116CH

S&F in repair angle valve cast copper alloy fancy type CP with long shank and cup and screwed for 15 mm iron pipe fixed as directed by Engineer in charge. Cera Cat Part No F1018201

Vitreous China urinals, size 375x390x590 mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. CERA Cat Part No S 4020112

S&F in repair Urinal Spreader cast copper alloy fancy type CP screwed for 15 mm iron pipe or PVC connection and fixed as directed by Engineer in charge. Cera Cat Part No F8070201

S&F in repair towel ring with material brass with glossy finish with fitting all as specified and as directed by engineer in charge. Cat Part Cera F5015115CH

S&F stainless steel Peg Set of Six of standard size (not less than 300mm long) fixed to wall with two rawl plugs and chromium plated brass screws complete all as specified & as directed. Make - Cat Part No BEA-30 of make - Prayag or equivalent in makes mentioned in Appendix 'B' here-in-after.

S & F in repair glass corner of size 300mmx300mm with 5.5 mm thick glass and stainless steel clip and stainless steel railing all round the shelf complete all as specified and as directed by Engineer in Charge. Cara Cat Part No F5005103.

M&L rendering 5 mm thick in CM 1:3 in ceiling finished even and smooth (without using extra cement)

M&L for preparation on newly plastered surface of ceiling for painting and applying 3 mm thick wall care putty on plastered wall surfaces and applying two coat of oil bound distemper all as specified and directed by Engr-in-Charge.

M & L for preparing surfaces of ceiling by complete removal of existing treatment and applying two coats of oil bound distemper over 3mm thick wall care putty on ceiling all as specified and directed by Engr-in-Charge

M&L rendering 15 mm thick in CM 1:6 on concrete solid block wall surface finished even and smooth without using extra cement.

M & L for preparing surfaces of walls by complete removal of existing treatment and applying two coats of oil bound distemper over 3mm thick wall care putty in two coats (smooth bodied opaque finish surface) on walls all as specified and directed by Engr-in-Charge

M&L for preparation on newly plastered surface of wall for painting and applying 3 mm thick wall care putty on plastered wall surfaces and applying two coat of oil bound distemper all as specified and directed by Engr-in-Charge.

Preparation of newly plastered surfaces of wall including cornices, pillasters etc and applying two coats of cement based paint, white or tinted over a coat of alkali resistant priming paint complete all as specified.

Dismantling cast iron pipes of any description any dia jointed in cement mortar all as specified and as directed by Engineer-in-charge.

M&L for complete removal of existing treatment of wall including cornices, pilasters etc by scraping down and applying two coats of cement based paint, white or tinted complete all as specified and as directed by Engineer-in-Charge.

S&F in repair PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement diametr of outlet 75mm bore complete all as specified.

M&L PVC (SWR) bends any radious 75 mm bore complete all as specified.

S&F in repair gun metal glob or gate valve with iron wheel head, screwed for iron pipe of 20mm dia complete all as specified & directed.

M & L for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified & directed.

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH

Supply & Fixing Exhaust fan (Heavy Duty) Steel body AC Single phase 230 Volt,50 Hz,900RPM,size 300 mm sweep with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar complete all as specified and as directed by Engineer-in-charge. Note : (i) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.