Construction of Govt. Primary School 1 and 2 Near Bus Station at Vanakbara-Diu (2nd Call)

Amount

Works

Earth Work Clearing and grubbing road land including uprooting rank vegetation. Grass bushes, Shrubs, saplings and trees girth up to 300mm removal of stumps of trees cut earlier and disposal of unserviceable and as directed by EIC. (C) By mechanical means in area of light jungle

Excavation for foundation upto 1.5m depth including sorting out and stacking of useful material and disposing off the excavated stuff upto 50 meter lead (A) Loose or soft soil

Excavation for foundation for depth from 1.5m to 3.0m including sorting out and stacking of useful material and disposing off the excavated stuff upto 50 meter lead (A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff up to 50 Meter lead and as directed by EIC. (E) Hard Rock

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff up to 50 Meter lead and as directed by EIC. (B) Dense or Hard Soil

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting out the soil and disposal of the surplus excavated soil as directed within a lead of 50m for following diameter of pipes (iii) 300mm including under reaming of bulb and as directed by EIC.

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each deposited layer by ramming (by manual or mechanical means) and watering and as directed by EIC.

Disposal of remaining excavated Earth after filling in foundations and plinth as per direction of Engineer in-charge including loading from site and unloading at disposal site for all lead and lift/depth etc. complete and as directed by EIC.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete etc and as directed by EIC.

Carrying out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistent with I.S.I specification. Using Chlordane and Chiorpurfiles 20 EC. As Per 6131_paret-II Concentration Weight one percent is recommended i.e. one litre 20 EC chemical emulsion with 19 litre give 1 % concentration inclusive of one litre chemical emulsion application at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S and as directed by EIC. Approved Makes for Anti-Termite Treatment: Pest Control India Ltd, Pest Con India,Pest Control Incorporated, or any other agency to be approved by the Engineer In-charge

Providing and filling rubbles including hand packing and filling voids with sand as directed including ramming and consolidating etc. complete and as directed by EIC.

Dewatering for work as original or extended including furnishing of pumps and other accessories all complete, as directed by the Engineer.

Rolling of earthwork in layers with power roller including filling in depression which occur duirng the process. Achieving proctor density of 95% at optimum moisture

PCC and RCC Works Providing and laying cement concrete 1:3:6 (1- Cement : 3- coarse sand : 6- hand broken stone aggregates 40 mm nominal size) and curing complete excluding cost of formwork in and as directed by EIC. (A) Foundation and Plinth

Providing and laying in position ready mixed M‐300 grade concrete for reinforced cement concrete work, using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of RMC from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including cost of admixtures in recommended proportions as per IS:9103 to accelerate/reatrd setting of concrete, improve workability without impairing strength and durability as per direction of the EIC without fly ash(min. cement level as per latest IS 456 shall be maintained) (Cement level 415Kg) , For Sub structure and super structure for all levels.

Providing formwork with sheathing steel sheets so as to give a fair finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4M and removal of the same for in situ reinforced concrete and plain concrete work in (A) Foundations, footings, bases of columns etc. and mass concrete and as directed by EIC.

Providing formwork with sheathing steel sheets so as to give a fair finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4M and removal of the same for in situ reinforced concrete and plain concrete work in (B) Flat surfaces such as soffits of suspended floors, slabs, landings and the like and as directed by EIC. (1) Floors etc. upto 200mm in thickness.

Providing formwork with sheathing steel sheets so as to give a fair finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4M and removal of the same for in situ reinforced concrete and plain concrete work in (C) Vertical surfaces such as walls (any thickness) partitions and the like including attached buttresses & string course & the like and as directed by EIC.

Providing formwork with sheathing steel sheets so as to give a fair finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4M and removal of the same for in situ reinforced concrete and plain concrete work in (H) (1) Sides and soffits of Beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1M in depth and as directed by EIC.

Providing formwork of ordinary timber / Plywood planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4M and removal of the same for in situ reinforced concrete and plain concrete work in (M) Staircase with sloping or stepped soffits including risers and stringers excluding landing and as directed by EIC.

Providing and laying damp proof course 25mm thick cement concrete 1:2:4 (1-cement : 2-coarse sand : 4-stone aggregate 10mm nominal size) and curing complete for plinth protection and as directed by EIC. Approved Makes of Cement: Larsen& Turbo,Gujarat Ambuja,Vikram,Binani or equivalent.

Providing and laying and fixing 50mm thick expansion joint by hydro cell semi rigid UV resistance with high performance laminated closed cell polythene foam joint filler in sheet foam as directed etc. complete and as directed by EIC.

52 mm thick cement concrete flooring (trimix) with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete and as directed by EIC.Approved Makes of Cement: Larsen& Turbo,Gujarat Ambuja,Vikram,Binani or equivalent.

Providing and fixing formwork for exposed concrete surface in desired pattern and size, using 18mm thick 120 micron film faced shuttering plywood, including neat cleaning the exposed concrete surface, rendering as directed by the consultant/site engineer, making drip moulds on the ledge & edges. Only the final exposed RCC surfaces shall be measured for payments. (Quality of the shuttering ply shall be approved by the engineer in charge prior to use). Rates shall be inclusive of shuttering for all shapes, sizes, fixing of drip mould patti, inserts, patterns in exposed form finish etc and for works at all levels using MS props for heights ranging from 4 to 16m and as directed by EIC.

Providing and laying cement concrete (IPS) flooring 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregates 20mm nominal size) laid in one layer and finished with a floating coat of neat cement and as directed by EIC. (B) 50mm thick and as directed by EIC.Approved Makes of Cement: Larsen& Turbo,Gujarat Ambuja,Vikram,Binani or equivalent.

Reinforcement Work Providing TMT Bars Fe500D reinforcement for RCC work including bending, binding and placing in position complete upto All floors level and as directed by EIC. Approved Makes of Reinforcement: SAIL, TISCO, RINL, VIZAG, Electrotherm or any other make as approved by the chief engineer.Including for additional lift And Placing in position of reinforcing steel for all RCC work above All floor level and as directed by EIC. Purchase certificate from the distributor to be provided.

Providing fusion bonded epoxy coating not less than 175 micron thickness and upto 300 micron to reinforecment bars as per IS‐13620‐1993/ASTM‐775 M including testing of coating at plant and all taxes All dia bars and as directed by EIC.Approved Makes of Reinforcement: SAIL,TISCO.RINL,VIZAG, Electrotherm or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Masonry Works White Stone Bela masonry work in partition walls upto 15cm thickness in cement mortar 1:4 (1 cement : 4 course sand) and as directed by EIC.

White Stone Bela Masonry block in course below plinth and in Supersctructure with stone of approved quality in lime mortar 1:6 (1 cement : 6 coarse Sand) including packing the joints complete and as directed by EIC.

Door Window Ventilatons Works Providing and fixing window having extruded aluminium color anodized section (20 Microns) frame main outer size 127mm x 38.10mm @wt. 1.7 kg/m, horizontal four track member size 121.6 mm x 47.7 mm @ wt 2.34 kg/m, vertical member of size 121.6 mm x 47.7 mm @ wt 2.34 kg/m with sliding shutters of horizontal member size 65 mm x 29 mm @ 0.849 kg/m, vertical member of size 65 mm x 29 mm @ 0.849 kg/m with 6mm thick transparent toughened float glass with anodized aluminium fittings and fixtures and all hardware (locks, handles, hinges, etc of Laval/ gessi make) and EPDM rubber/ neoprene gasket of ebco make for glass fixing to frame as per details etc. complete for window and as directed by EIC including necessary filling up the gaps at junctions with silicon sealant of approved color ( Wacker, Dow corning make). Approved Makes of Aluminium Extrusion: Jindal (cardinal series),Hindalco, Indal or any other make as approved by the chief engineer. Approved Makes of Float Glass: Modi guard, Saint gobain, Asahi, Atul or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Providing and fixing window having extruded aluminium color anodized section (20 Microns) frame main outer size 127mm x 38.10mm @wt. 1.7 kg/m, horizontal three track member size 85.8 mm x 47.7 mm @ wt 1.67 kg/m, vertical member of size 85.8 mm x 47.7 mm @ wt 1.67 kg/m with sliding shutters of horizontal member size 65 mm x 29 mm @ 0.849 kg/m, vertical member of size 65 mm x 29 mm @ 0.849 kg/m with 6mm thick transparent toughened float glass with anodized aluminium fittings and fixtures and all hardware (locks, handles, hinges, etc of Laval/ gessi make) and EPDM rubber/ neoprene gasket of ebco make for glass fixing to frame as per details etc. complete for window and as directed by EIC including necessary filling up the gaps at junctions with silicon sealant of approved color ( Wacker, Dow corning make). Approved Makes of Aluminium Extrusion: Jindal (cardinal series),Hindalco, Indal or any other make as approved by the chief engineer. Approved Makes of Float Glass: Modi guard, Saint gobain, Asahi, Atul or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Providing and fixing window having extruded aluminium color anodized section (20 Microns) frame main outer size 127mm x 38.10mm @wt. 1.7 kg/m, horizontal two track member size 50 mm x 47.7 mm @ wt 1.15 kg/m, vertical member of size 50 mm x 47.7 mm @ wt 1.15 kg/m with sliding shutters of horizontal member size 65 mm x 29 mm @ 0.849 kg/m, vertical member of size 65 mm x 29 mm @ 0.849 kg/m with 6mm thick transparent toughened float glass with anodized aluminium fittings and fixtures and all hardware (locks, handles, hinges, etc of Laval/ gessi make) and EPDM rubber/ neoprene gasket of ebco make for glass fixing to frame as per details etc. complete for window and as directed by EIC including necessary filling up the gaps at junctions with silicon sealant of approved color ( Wacker, Dow corning make). Approved Makes of Aluminium Extrusion: Jindal (cardinal series),Hindalco, Indal or any other make as approved by the chief engineer. Approved Makes of Float Glass: Modi guard, Saint gobain, Asahi, Atul or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Providing and fixing standard extruded of aluminium section of size 63.50mm x 38.10mm x 1.95mm @wt. 1.094 kg/m with color anodized (20 microns) aluminium frame with 5mm thick transparent bronze color tinted float glass with color anodized aluminium frame for ventilation with 6mm thick frosted glass as per details etc. complete for window and as directed by EIC.Approved Makes of Aluminium Extrusion: Jindal (cardinal series),Hindalco,Indal or any other make as approved by the chief engineer. Approved Makes of Float Glass: Modi guard,Saint gobain,Asahi,Atul or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Providing and fixing standard extruded of aluminium section of size 63.50mm x 38.10mm x 1.95mm @wt. 1.094 kg/m with color anodized (20 microns)aluminium frame with 6mm thick transparent toughned float glass as per details etc. complete for fix window and as directed by EIC.Approved Makes of Aluminium Extrusion: Jindal (cardinal series), Hindalco,Indal or any other make as approved by the chief engineer. Approved Makes of Float Glass: Modi guard, Saint gobain, Asahi, Atul or any other make as approved by the chief engineer. Purchase certificate from the distributor to be provided.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket (ebco make) etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer‐in‐charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to approved shade according to IS: 1868, Minimum anodic coating of 20 microns) and as directed by EIC. Purchase certificate from the distributor to be provided.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket (ebco make) required (Fittings shall be paid for separately) and as directed by EIC. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of 20 microns) and as directed by EIC. Approved Makes for Fasteners: Fischer,Hilti,Anchors or any other make as approved by the chief engineer.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer‐ in‐charge. Pre‐laminated particle board with decorative lamination on one side and balancing lamination on other side.Approved Makes for Fasteners: Fischer,Hilti,Anchors or any other make as approved by the chief engineer. Approved Makes of Prelaminated Particle Board: Novapan,Merino,Green lam,Archid lam or any other make as approved by the chief engineer.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer‐ in‐charge. Pre‐laminated particle board with decorative lamination on both sides. Approved Makes for Fasteners: Fischer,Hilti,Anchorsor any other make as approved by the chief engineer. Approved Makes of Prelaminated Particle Board: Novapan,Merino,Green lam,Archid lam or any other make as approved by the chief engineer.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket (ebco make) etc. complete as per the architectural drawings and the directions of engineer‐in‐charge . (Cost of aluminium snap beading shall be paid in basic item): With toughned float glass panes of 8 mm thickness (weight not less than 20 kg/sqm). Approved Makes for Fasteners: Fischer, Hilti, Anchors or any other make as approved by the chief engineer. Approved Makes of Prelaminated Particle Board: Novapan,Merino,Green lam,Archid lam or any other make as approved by the chief engineer.Approved Makes of Float Glass: Modi guard,Saint gobain,Asahi,Atul or any other make as approved by the chief engineer.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer‐in‐charge. With stainless steel cover plate minimum 1.25 mm thickness.Approved Makes for Floor Door Spring: Ozone/ Arl bihari make or any other make as approved by the chief engineer.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer‐in‐Charge. Anodized (20 microns) aluminium tubular handle bar. Approved Makes for Fasteners: Fischer,Hilti,Anchors or any other make as approved by the chief engineer. Approved Makes of Locks and Handles: Laval/ Gessi make or any other make as approved by the chief engineer.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately). Approved Makes for Floor Door Spring: Ozone/ Arl bihari or any other make as approved by the chief engineer.Approved Makes of Float Glass: Modi guard,Saint gobain,Asahi,Atul or any other make as approved by the chief engineer.

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer‐in‐ charge complete, complying to ASTM C920, DIN 18540‐ F & ISO 11600. Upto 5 mm depth and 5 mm width.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete and as directed by EIC.Approved Makes for Fasteners: Fischer,Hilti,Anchors. Approved Makes of Locks and Handles: Laval/ Gessi or any other make as approved by the chief engineer.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete and as directed by EIC.Approved Makes of Door Fitings: Godrej,Doorset or any other make as approved by the chief engineer.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all members to be polished members including machine cutting, grinding and finished in line and level, no welding to be seen. including priming coat with approved steel primer all complete and as directed by EIC. Fixed to steel windows by welding. Approved Makes of paints: Berger, Asian paints or any other make as approved by the chief engineer.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all members to be polished members including machine cutting, grinding and finished in line and level, no welding to be seen including priming coat with approved steel primer all complete and as directed by EIC. Fixed to openings by welding. Approved Makes of paints: Berger, Asian paints or any other make as approved by the chief engineer.

Steel Works Providing and fixing M.S. PIVOT Gates of required pattern fixed to brick walls / Columns prepared with M.S. flats, angles, Square / round bars, square pipes, at required spacings with necessary hold fasts, Rollers and other fixtures and fittings as per detailed drawing and fixing brick walls / coping / columns etc. complete including one coat of primer and two coats of Epoxy Paint including cleaning and finishing the surface etc. complete and as directed by EIC. Approved Makes of paints: Berger, Asian paints or equivalent.

Structural Steel work (confirming to IS 4923-1997) riveted, bolted or welded in builtup for all type sections, in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per the structural designs and directions of EIC. Approved Makes for Steel : SAIL,TISCO,RINL,VIZAG or equivalent.Approved Makes for Fasteners: Fischer,Hilti,Anchors or equivalent.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works as per architecture drawing. Sample to be prepared for approval from architect.

Flooring Works Providing and laying river wash kota stone slab 25 mm thick flooring as per the drawings and directed by Engineer in Charge over 20 mm (Average ) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including, epoxy grout filling, rubbing and polishing etc. complete and as directed by EIC.Including groovs,Epoxy As per Architecture Drawing. The exposed edges to be of uniform thickness and polished

Providng and laying Vitrified tiles 8 to 10mm thick, 24" x 24" in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-Coarse sand) finishing with flush pointing in white cement and as directed by EIC.Including groovs,Epoxy As per Architecture Drawing.

Providng and laying Vitrified tiles 8 to 10mm thick, 24" x 24" in skirting, risers of steps and dado laid on a bed of 10mm thick cement plaster 1:3 (1-cement : 3-Coarse sand) and jointed with white cement slurry and as directed by EIC.Including groovs,Epoxy As per Architecture Drawing. For dado tile adhesive of Kerakol to be used.

P & L 24"x24" vitrified 8mm thick tile flooring over 20mm (average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finished with flush pointing & cleaning the surface etc. complete for anitskit and as directed by EIC.Including groovs,Epoxy As per Architecture Drawing.

Providng and laying mirror finish polished kota stone slab flooring and door window jambs over 20mm (average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or LM 1.1.5 (1-lime putty : 1.5-coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete and as directed by EIC. (A) 25mm thick.Including groovs,Epoxy As per Architecture Drawing. The exposed edges to be of uniform thickness and polished.

Providng and laying mirror finish polished kota stone slab flooring over 25mm thick in risers of steps, skirting, dado and pillars laid on 10mm thick cement mortar 1:3 (1-cement : 3-coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete and as directed by EIC.Including groovs,Epoxy As per Architecture Drawing. The exposed edges to be of uniform thickness and polished.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length, 30cm height and 15cm thick of M250 grade concrete as per approved design and including excavation for fixing in proper line and level, filling the joint with C:M 1:3 (1 cement: 3 fine sand) etc. complete and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent. Approved Makes of Kerb Stone: Dalal tiles,Unistone,Modern , Vyara or equivalent.

Providing and fixing pre-cast rubber dye / steel dye inter locking concrete block 60mm thick with grade of concrete M300 pneumatic compressed / vibrated mechanically and as per approved design confirming to IS 15658 : 2006 including 35mm sand layer for levelling and filling the joint with sand in proper line and level as per guidelines of IRC : SP 63-2018 etc. complete and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent. Approved Makes of Interlock Blocks: Dalal tiles,Unistone,Modern, Vyara or equivalent.

Providing and laying broken china mosaic flooring for terrace using 12mm to 20mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar crème out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall, clearing with water and oxalic acid etc. as directed and as directed by EIC.

40 mm thick Rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent.

Water Proofing Works Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry and as directed by EIC.Approved Makes of Water Proofing: Creations,Pidilite,Cico or equivalent.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage and as directed by EIC.Approved Makes of Water Proofing: Creations,Pidilite,Cico or equivalent. (a) For vertical surface two coats @ 0.70 kg per sqm

(b) For horizontal surface one coat @1.10 kg per sqm

Providing cement vata (10 cm x 10 cm size) quarter round in cement mortar 1:1 including neat cement finishing, watering, etc. and as directed by EIC.

Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).and as directed by EIC.

Wall and Ceiling Finishing Works Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately).Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent.

Providing 20mm thick cement plaster in single coat on single or half brick walls walls for interior plastering upto floor two level and finished even smooth in (i) Cement mortar 1:3 ( 1 cement : 3 sand) and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent.

Extra over above item for interior plastering above floor two level for every additional storey height. (1) Single coat plaster and as directed by EIC.

20mm thick sand faced cement plaster on walls upto height 10 meters above ground level consisting of 12mm thick backing coat of C.M 1:3 (1 cement : 3 sand) and 8mm thick finishing coat of C.M 1:1 (1 cement : 1 sand) etc. complete and as directed by EIC. Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent.

Providing 20mm thick double coat mala cement plaster on interior brick / concrete work for plastering comprising of base coat of 12mm thick cement plaster in cement mortar (1 cement : 4 coarse sand) in rough finishing and 8mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished with trovel including scaffolding, curing etc. complete and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani or equivalent.

Providing 20mm thick cement plaster by using ready mix mortar for plaster in single coat on single or half walls for interior plastering upto floor two level and finished even and smooth in cement mortar 1:6 (1 cement : 6 sand) and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani.

Finishing wall with water proofing cement paint of on wall surfaces (two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials and as directed by EIC.Approved Makes of cement: Larsen & Turbo, Gujarat, Vikram, Binani.Approved Makes of Water Proofing: Creations,Pidilite,Cico or equivalent.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth and as directed by EIC. makes: Asian or Dulux

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm and as directed by EIC. makes: Asian or Dulux

Applying priming coat over new steel and other metal surface after and including preparing the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter and scoured with brushes fine steel wood, scarpers and sand paper with ready mixed priming paint brushing red lead and as directed by EIC. makes: Asian or Dulux

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade inculding cleaning the surfcae of all dirt, dust and other foreign matter and as directed by EIC. makes: Asian or Dulux

Finsihing wall with weather proof exterior emulsion paint on wall surface (two coats) to give a required shape even shade after thoroughly brushing the surface to remove all dirt, and remians of loose powdered materials etc. complete and as directed by EIC. makes: Asian or Dulux

Applying two coats of cement base putty and two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth and as directed by EIC. makes: Birla or JK

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with afloating coat of neat cement on the Ceiling.CEMENT PLASTER IN SINGLE COATS

Other Items 25mm thick mirror Polished Kota Stone slabs on exposed face Stone work (machine cut edges in Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including grinding area hand grinder on joints rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) and as directed by EIC.

Providing and fixing of 8mm Calcium Silicate False ceiling/ 12.5mm tapered edge Gypsboard False ceiling consisting of tee/ angle sections/ box section, of approved make conforming to IS : 733 in frames of false ceiling including trap doors, aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer‐ in‐ charge (including level adjusting hangers, ceiling cleats and expansion hold fasteners) and as directed by EIC. Approved Makes of Saint gobain/ Gyproc/ Gyp Steel or any other make as approved by the chief engineer. Approved Makes of Aluminium Extrusion: Jindal, Hindalco, Indal or any other make as approved by the chief engineer. Approved Makes of Expansion and Fasteners: Fischer, Hilti, Anchors or any other make as approved by the chief engineer. The pattern to be as per drawing including matching with expose RCC wherever required.

Providing and fixing suspended open cell false ceiling of Hunter douglas make or Armstrong Cellio or equivalent - Metal/Aluminium Open Cell Ceiling-of 100x100mm cell size with all the accessories. Open Cell Ceiling :- Providing & Fixing Open cell type grid ceiling Providing and fixing in true horizontal level Open cell Aluminum lay- in ceiling tiles of size 600mmx600mmx38mm having Humidity Resistance of 100% RH, and having Fire Performance A2-s2, d0. The tile of ‘global white’ color with cell size options of 150mm (81% open area) /100mm (72% open area). The grid should be of “Armstrong” make with 15mm wide T - section flanges color white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 14 Kgs/M2. The T Sections have a Galvanizing of 90 grams per M2 & passed through 500 hrs of Salt test. The Tile & Grid system used together should carry a 15 year warrantee and as directed by EIC. INSTALLATION: To comprise main runner spaced at 1200mm centers 1975 securely fixed to the structural soffit using Armstrong or equivalent suspension system (specifications below) at 1200mm maximum centre. The First/Last Armstrong suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers. accessories manufactured and supplied by OEM consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanized steel of size 26 x 26 x 25 x 1.2mm with a Galvanized Thickness of 80gsm, A pre Straightened Hanger wire of dia – 2.68 mm of 1.83 m length., thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanized spring steel for 2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner.

Providing, Making, Fixing / Applying Glass Fiber Reinforced Pigmented Concrete GRC Fin, Jali , beam, gate & paragola of Various Sizes with perforation and as shown in drawing using well graded Approved fine quality aggregates, alkali resistant glass fibres, admixtures, water and cement including curing, Scaffolding, cleaning, preparing surfaces, junctions etc, prepare shop drawings showing fixing and methodlogy and arrangements, taking its approvals, modifying to suit site dimensions, taking approval of mock ups prior to installation/ fixing/ making of features and including all SS fittings, SS hardware, SS screws, SS fasteners, SS washers, SS clamps etc. complete and as directed by EIC. The item to be executed in line, level and plumb at all level. The item to be include all tools, tackles, scaffolds, hardware clamps and adhesive

Providing and applying Epoxy Grouting as per Architect's choice and as directed by EIC.

Box cutting the road surface to proper slope and camber for making a base of road work including removing the excavated stuff and depositing on the road side slope as directed upto50 mts, lead and as directed by EIC.

Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position and as directed by EIC. Including trap doors (a) Indian Teak Wood, the item to include french polishing

Providing and fixing of heavy duty bearing/ Top Bottom Pivot in pivot gates in main gates, Bearing should be rust free as should be of required capacity as per design given by architect or engineer in charge.

Providing and fixing of handmade clay block jalis as per design approved by architect or engineer in charge including Kerakol chemical required to stick it to existing surface including SS 316 peripheral / internal framing of 8mm x 35mm , cleaning it and filling joints with required chemical and as directed by EIC. To be executed in line, level and plumb at all levels. The rate to include all tools, tackles, scaffolds, nuts bolts and adhesives. Sample to be made for approval of architect before final execution. Approved Makes of clay block jali: Clay club innovative or any other make as approved by the chief engineer.

Providing and laying Diamond Core cutting Required in RCC/ Bricks walls required for electric pipes/ Ac Ducts, Etc depth upto 380 mm. 2" Diameter and as directed by EIC.

Providing and laying Diamond Core cutting Required in RCC/ Bricks walls required for electric pipes/ Ac Ducts, Etc depth upto 380 mm. 3" Diameter and as directed by EIC.

Providing and laying Diamond Core cutting Required in RCC/ Bricks walls required for electric pipes/ Ac Ducts, Etc depth upto 380 mm. 4" Diameter and as directed by EIC.

Providing and laying Diamond Core cutting Required in RCC/ Bricks walls required for electric pipes/ Ac Ducts, Etc depth upto 380 mm. 5" Diameter and as directed by EIC.

Providing and laying Diamond Core cutting Required in RCC/ Bricks walls required for electric pipes/ Ac Ducts, Etc depth upto 380 mm. 6" Diameter and as directed by EIC.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 brick bats 40 + 50mm size ) inside plastering 15mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) inside size 900mm x 120mm x 1.5 m deep including CI cover and frame to be not less than 128 kgs (wt. of cover 64 kg and wt. of frame 64 kg). (A) with 230mm thick walls of brick masonry using brick having crushing strength not less than 35 kg/Sq cm. in cement mortar 1:5 ( 1 cement : 5 coarse sand) (1) A type depth 0.90 m and as directed by EIC. Approved Makes of Cement : LArsen and Turbo,Gujarat Ambuja,Vikram,Binani or equivalent.

Providing and fixing cover over expansion joint made with aluminium and material grade 6061-T6 having properties like water resistant and impact resitant and joint width 50-350mm with complete accessories and as directed by EIC.

Providing and fixing deodar shuttering and drip mould as per the design provided by the architect with complete accessories and as directed by EIC.

Providing and fixing mechanical anchor fastener of hilti,fischer,anchors or equivalent make for required fitting with hilti epoxy adhesive 100*10 mm and as directed by EIC.

Providing and fixing mechanical anchor fastener of hilti,fischer,anchors or equivalent make for required fitting with hilti epoxy adhesive 150*10 mm and as directed by EIC.

Providing and laying cinder filling in sunken floors and other locations with approved quality cinder inculding watering and light ramming etc. required for proper compaction/completion of the work complete in all respects as per drawings and as directed by EIC.

Providing and laying bentonite slurry for piling works including preparing, providing and re-circulating bentonite slurry in the trench as and when required for all depths, including agitating bentonite slurry during trenching etc., providing and fixing stop ends or form tubes, upto the required depth including extracting the same after casting, including chipping off the bentonite adulterated concrete or unsound concrete up to the cut off level for obtaining the sound concrete, dressing undulations on the exposed face of diaphragm wall after excavation by chipping / chiseling etc. including filling the depression/ cavities with sound concrete etc. complete and as directed by EIC.

Providing and laying of dry lean cement concrete with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 26.5 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting, finishing and curing and as directed by EIC.

Polishing with french polish on new wood and wood based surface to give an even surface including cleaning the surface of all dirt, dust and sand papering smooth and including a coat of wood filler and as directed by EIC.

Preparing plastered surface including cleaning and rendering the same using grey cement and white cement mortar and slurry using curing cloth and achieving an exposed concrete looking surface over pre-plastered surfaces and including making buttons resembling filled up holes of tir rod details of RCC walls. Rates shall be inclusive of all tools, tackles and scaffolding material and for works at all levels and as directed by EIC.

Supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. having thermobonding a draining core - HDPE geonet comprises of two sets of parallel overlayed ribs integrally connected to have a rhomboidal shape with a polyethylene film and a nonwoven geotextile having mass per unit area 130 gsm and tensile strength of 8.0 kN/m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 0.7 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength of 13.5 kN/m , with mass per unit area of 830 gsm, at easily accessible location including top and bottom, with all leads and lifts, manpower and machinery, materials, labour etc. complete and as directed by Engineer - In - Charge.

Providing and fixing formwork including centering, shuttering, strutting, staging, propping, bracing using tubular H frames, cuplocks, stirrup heads, adjustible acrow props, adjustible acorw spans, etc. complete and including its removal at all levels for all types structural and non-structural members. The rates shall be inclusive of all tools, tackles, plant, machinery, plywood (of appropriate thickness and density, but min of 12mm thickness), bracing, supporting and also making the shuttering water tight and in correct line, level, shaoes, making drip moulds, grooves, leaving inserts etc. as per the Consultant's designs and as per the direction of EIC. Thw works shall be carried out as per the designs of the consultants.

Extra for providing and fixing expanded metal mesh of size 20x60 mmand strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm forencasing of rolled steel sections in beams, columns and grillages,excluding cost of hangers. STEEL REINFORCEMENT

PART-A:- WATER SUPPLY PLUMBING & SANITARY FITTING:- Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing in Cement Mortar 1:3 (1-Cement : 3-coarse sand)a, pair of white vitreous China 250mm x 130mm x 30mm footrest to long pattern squatting pan water closet.

Providing and fixing 12.5 Litres low level flushing cistern with a pair, of C.I. or Mild brackets, complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with polythene float, C.P brass handle unions and couplings for connections, with inlet, outlet and overflow pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the same connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)(A) Vitreous China (I) In white colour

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia.

Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia.

Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia.

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni trap.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (ii) 20mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia. Prass Type

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing screw down bib taps of following size.(C) Gun metal screw down bib tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(C) Gun metal screw down bib tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (ii) 20mm dia.

Providing and fixing brass screw down stop tap.(A) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing brass screw down stop tap.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(A) 15mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40 mm dia.

Supply, instalation, testing & commissioning of C.I. Butterfly Valve D/F/. as per IS:13095 ISI mark -PN-1.0 including all taxes, transportation, freight charges, octroi, inspection, testing, ,loading, unloading etc to complete the job. ( Zoloto/ Audco/ R.B.)50mm dia.

Supply, instalation, testing & commissioning of C.I. Butterfly Valve D/F/. as per IS:13095 ISI mark -PN-1.0 including all taxes, transportation, freight charges, octroi, inspection, testing, ,loading, unloading etc to complete the job. ( Zoloto/ Audco/ R.B.)65mm dia.

Supply, instalation, testing & commissioning of C.I. Butterfly Valve D/F/. as per IS:13095 ISI mark -PN-1.0 including all taxes, transportation, freight charges, octroi, inspection, testing, ,loading, unloading etc to complete the job. ( Zoloto/ Audco/ R.B.)80mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(ii) 25mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(iii) 32mm dia.

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc. complete.(A) White earthenware flat back or corner type size 430mm x 260mm x 350mm.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (ii) 50mm dia.

Providing and fixing ball cock of approved. quality as directed.(B) Abonite (i) 25mm dia.

Providing and fixing ball cock of approved. quality as directed.(B) Abonite (ii) 50mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [F] 50mm.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge:- 65mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge:- 80mm dia.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing white vitreous china extended wall mounted water closet (European type) of size 370 x 535 x 405 mm of approved shape including providing and fixing white vitreous china cistern with dual flush fitting of flushing capacity 3 litter/ 6 litter, including seat and lid, fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved design complete, including chair brackets, nuts, rag bolts, painting of fittings and brackets, cutting and making good the walls and floors wherever required. Wall mounted water closet of Jaquar : CNS-WHT-959NN Coupled Closet Cistern: , Health Faucet ALD-CHR-573 or Equivalent approved Make . ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing & fixing of first quality white vitreous china Oval type Wash basin as per product detail, including specially fabricated C.I. brackets with studs painted with two or three coats of enamel paint of approved shade over a coat of primer complete including filling gap between counter and wash basin with approved sanitary grade material, cutting & making good the walls where required to the complete satisfaction of the Engineer in Charge. Oval Wash Basin of Jaquar - FLS-WHT-5701; Rag Bolts for Wash Basins, Bottle Trap: Jaquar ALD-769L300x190, Waste Coupling: Jaquar: Cat. No.: ALD-705, Prassmatic Pillar Cock: Jaquar PRS-031 or Equivalent approved Make . ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing & fixing of first quality white vitreous china Wash basin as per product detail, including specially fabricated C.I. brackets with studs painted with two or three coats of enamel paint of approved shade over a coat of primer complete including filling gap between counter and wash basin with approved sanitary grade material, cutting & making good the walls where required to the complete satisfaction of the Engineer in Charge. Wash Basin CNS-WHT-811; Rag Bolts for Wash Basins, Bottle Trap: Jaquar ALD- 769L300x190, Waste Coupling: Jaquar: Cat. No.: ALD-705, Prismatic Pillar Cock: Jaquar PRS-031 or Equivalent approved Make . ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing white vitreous china flat back urinal of approx. size 375 x 315 x 620mm having water inlet & outlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Urinal: Jaquar Make URS-WHT-13253O, Urinal Flush PRS-073 or Equivalent approved Make . ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing of Jaquar Urinal Partition (Model no.- 1810-UC /1810-US) made of 8mm colour chrome Toughened Glass & Frosted in Curved Shaped height 900 mm width 450mm or equivalent make including all necessary fitting to be fixed by drilling holes with Brass bracket in Chrome finish all Complete as per drawing and directed by engineer-In-Charge. ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing & fixing Single Lever concealed Diver with Over head wall Shower and Spout Assembly, ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing & fixing of Health faucet with Angular Cock Assembly( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Handicaped Toilet Providing and Fixing Handicap Toilet set including EWC, Cistern, Seat Cover, Fittings, Washbasin,, Hinged Rail, Grab Bar and Faucet with Spatula Lever including Cast Iron chair backed and necessary bolts and nuts complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required to the satisfaction of Engineer-In-Charge. Special Needs Toilet Set: Jaquar - CNS-WHT- 755SN + Cistern Set CNS-WHT-207, Wash Basin CNS-WHT-811 & Grab Bar 2 No. - WAC-WHT-BG0800 & WAC-WHC-BR0600 - 2 nos.+ or Equivalent approved Make ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing 2 Nos. support arms and backrest to mount at fixed height (Commander or equivalent) for handicap toilet complete as recommended by the E-I-C. ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing raised toilet seat with cover for handicap toilet (Commander or equivalent) as recommended by the E-I-C ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing brackets, tracks with flexible feed & waste pipes for adjustable type wash basin complete as recommended, for handicap toilet (Commander or equivalent) ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing and fixing white vitreous china extended wall mounted bidet pan (European type Wall Hung Bidet ) of size 550 x 370 x 340 mm of approved shape including providing and fixing hot and cold water mixer inbuilt assembly , including seat and lid, fittings & C.I.brackets, washout,drain arrangement with specials of standard make and mosquito proof coupling of approved design complete, including chair brackets, nuts, rag bolts, painting of fittings and brackets, cutting and making good the walls and floors wherever required. Wall mounted Bidet closet of Cera : 550 x 370 x 340 mm Cat. No. S5020101 Bidet white or Equivalent approved Make . ( Cera/ Jauar/Hindware/Parryware or Eq. Make)

Providing & fixing double layer PVC OH Tank (Sintex or equivelant make approved by Architect) with piping, valves and neccasary standard fixtures fittings and testing ect. Complete on terrace as directed by E.I.C.

Making holes upto 50mm dia. 300mm long in any RCC members by diamond Core Cutting machine of HILTI or equivalent including disposing the debries,all works refinishing of the GP-2 pipe grout complete with water proof testing etc completed as directed by E.T.C/PMC .

Making holes upto 100mm dia. 300mm long in any RCC members by diamond Core Cutting machine of HILTI or equivalent including disposing the debries,all works refinishing of the GP-2 pipe grout complete with water proof testing etc completed as directed by E.T.C/PMC ..

Making holes upto 150mm dia. 300mm long in any RCC members by diamond Core Cutting machine of HILTI or equivalent including disposing the debries all works refinishing of the GP-2 pipe grout complete with water proof testing etc completed as directed by E.T.C/PMC .

PVC PIPE SLEEVE WORK DURING CONSTRUCTION PHASE:- Providing and fixting of the PVC -6kg. pipe sleeves of 75mm,100mm&150mm dia pipe during civil work casting works, the lenght of pipe should be 450mm and 300mm as per the requirments, the sleeve works must be coordinated with the civil agency, beam, sleeves, slab and RCC reating walls etc. complete as directed by EIC/Architect

SITC of Heavy duty PVC flexible pipe of 25mm dia with 15 meter length , the pipe shouble be included Gunmetal hose nozzel at the termination point. For gaden manual irrigation purpose. As per the site eng. incharge and as per the guide line o be execute. (Pipe:- Ashirvad, Kissan, Supreme, valve RB, Zoloto, Audco or Eq. Make)

Providing and fixing elecatrical ot water geyser of having capacity of 6 ltr. Storage with including necessary inlet, outlet connection, safety valve, elecatical necessary cabel requirments, including fastning and fixing in the clamp and other protection all complete works. ( AO Smith, Jaquar, Spearhot or eq. make)

APPROVAL WATER SUPPLY SERVICES CONNECTION FROM LOCAL AUTHORITY Getting of Water supply connection of nearest water point from Approval from local drainage & water authority with all other charges and documentations for getting No Objection Certificate.

PART-B:- DRAINAGE & SEWERAGE & RAIN DRAIN ITEM:- Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(A) 100mm dia. (upto 10 ton)

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. (166mm Ave. bed thickness)

Providing and laying lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. 300mm width (112 mm Ave.bed thickness)

Providing and laying lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. 450mm width (166mm Ave. bed thickness)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(i) Bends of required degree (any redious) of following nominal diameters. (A) 100mm dia. (upto 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(i) Bends of required degree (any redious) of following nominal diameters.(B) 150mm dia. (upto 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(ii) Taper bend of required degree of following internal diameters.(A) 100mm x 150mm (upto 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(iii) Single Junction of required angle of following internal diametrs. (A) 100mm. (upto 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(iii) Single Junction of required angle of following internal diametrs. (B) 150mm. (upto 10 ton)

Providing and laying jointing and pointing with stiff mixture of Cement Mortar 1:1 (1-Cement : 1-Fine sand) 150 mm internal diameter salt glazed stoneware half round channels. (upto 10 ton)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(C) 250mm (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton)

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (3) C type depth 2.25 Metre for 150mm diameter sewer.

(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (4) D type depth 3.15 Metre for 150mm diameter sewer.

(I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No.24.27 (I) for depth from 0.9M to 1.5M.

(II) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to 2.25M.

(III) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No. 24.27 (III) for depth from 2.25M to 3.15M.

(IV) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No. 24.27 (IV) for depth above 3.15M.

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-corrosive paint etc. complete.

Supplying and fixing C.I. cover 300mm x 300mm without frame for Gulley trap (Standard pattern) te weight of cover to be not less 4.53 Kg.) (upto 10 ton)

Providing and erecting at the site of work steel ventilating column of 150m internal diameter and 12.20 Metre High from G.L. to bottom of top grill including C.I. grill and base plate bolts and nuts etc. and excavation in foundation of size 120cm. x 120vcm. x 165cm. and filling the pit with first layer of cement concrete 1:3:6 mix (1-cement :3-coarse sand :6-graded stone aggregate 20mm nominal size) of 120cm. x 120cm. x 90cm. and remaining pit with B.B.C. 1:3:6 mix (1-cement :3-coarse sand:6-Brickbats 40+50mm size) and providing fillet in Cement concrete 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm. nominal size) at G.L. and 3 coats of silver paint etc. complete. (upto 10 ton)

Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm C.I. horizontal grating wih frame complete. (upto 10 ton)

Constructing Brick masonry road gully chamber 450mm x 450mm x 775mm with vertical gating complete.

Constructing brick masonry road gully chamber 1100mm x 775mm including 500mm x 450mm (C.I. horizontal grating with frame and vertical grating complete.) (upto 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. (upto 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x mm and 450mm deep for pipe lines with three or more inlets. (upto 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(iii) for 600mm x 850mm size.

(A) Providing sock pit of 2.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Constructing water tight brick masonry grease trap with second class bricks in cement mortar 1:4 (1 cement :4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement & FRP. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), two brick masonry baffle walls each of 500 mm depth & third one 600 mm deep each of 115 mm thickness, 1 No. cast iron double seal manhole cover with frame (internal size 455 x 610 mm & total weight of cover & frame to be not less than 38 kgs) & 2 Nos C.I. double seal medium duty covers each of 600 x 600 mm size including excavation, backfilling & disposal of surplus earth complete as per standard design.(Note : Cost shall include dewatering & water proofing of chambers as directed at site).Grease Trap (Size 1500 x 750 x 1200 mm lequid depth).

APPROVAL WASTE WATER DRAIN CONNECTION FROM LOCAL AUTHORITY Getting of waste water drain connection of nearest drain point from Approval from local drainage & water authority with all other charges and documentations for getting No Objection Certificate.

Providing & fixing of the FRP recessed type cover with frame size 600 x 600mm size total weight of cover and frame to be withstand up to 25 ton. with including Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) 25 ton Cap. Recessed type cover( Cover-600 x 600mm ) ( Frame:- 812 x 812mm)

Providing & fixing of the FRP recessed type cover with frame size 600 x 600mm size total weight of cover and frame to be withstand up to 25 ton. with including Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) 40 ton Cap. Recessed type cover( Cover-600 x 600mm ) ( Frame:- 812 x 812mm)

Excavation for pipes upto1.50 MT depth including sorting out and stacking of useful materials and disposing the excavated stuff up to 50 mt lead ( A ) loose or Soft Soil

Excavation for foundation up to 1.50 MT depth including sorting out and stacking of useful materials and disposing the excaveted stuff upto 50 mt lead (B) Dense or hard soil

PART-C:- PERCOLATION WELL :-3 nos Cobsideration. Boring and Sinking 30 cm. Diameter. Percolation well

Soak well around 2.0 m. dia. X 3.0 m. liquid depth as per the design and drawings.

Brick masonry collection cum filtration tank around soak well

15 cm. diameter strainer pipes (Johnson make) having slot size 1.5 mm x 57 mm (72 slots in one line) in the casing pipe

Supplying, fitting, fixing and lowering 30 cm. diameter strainer pipe 1.2 m long (Johnson make) having slot size 1.5 mm x 57 mm (72 slots in one line)

Providing and lowering 15 cm size M.S. (3 m long) bail plug to the bore hole.

Supplying, lowering, fitting, fixing and joining with Strainer, 15 cm. diameter M.S. Pipe of minimum 5.40 mm wall thickness

Cement ceiling the saline zone as per logging report and as directed by the employer.

Supplying, washing and shrouding with approved gravel, the annular gap between the casing pipe and the remaining annular space to be filled in with puddle clay (for which no measurement with be taken and paid for )

Hire and labour charges for necessary tools and plants for conducting proper tests for percolation water,

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

PART-D:- PUMPS & EQUIPMENTS :-HYDRO PNEUMATIC SYSTEM:-Supply, installation, testing & commissioning of VFD based Hydropneumatic system with FRP tank, pump-motor set, suction delivery valves & pipe, all instrumentation viz. Pressure switch, pressure gauge, level indicator, etc, starter panel (including one main pump & one trimmer pump shall have VFD), cables, etc. FRP Hydropneumatic Tank with inter connection and suitable connections such as inlet, drain, outlet, pressure gauge, union connection, isolation valve, outlet pipe (to be connected to the header pipe), pressure switch, outlet valves, mounting pads, etc. with all accessories. vertical booster pumps directly coupled with the motor with SS casing, SS impeller, SS shaft and driven by 415 V AC, 3 phase, 50 Hz.motor running at 2900 RPM speed and shall be supplied with all accessories viz. strainer / dry run protection/foot valve, base plate, coupling, etc.complete. The scope shall also include suction & delivery piping & valves.( Domestic UGT to OHT Feeder )( Grundfos, ITT Lowara, or Eq.Make)Domestic Water Supply System :15.0m3/hr x 2 Nos. main Pumps ( 1 Working + 1 Stand by Set)Head : 30 mtr.Booster Tank : 100 ltrs. x 1 nos.

FLUSHING :-HYDRO PNEUMATIC SYSTEM:-Supply, installation, testing & commissioning of VFD based Hydropneumatic system with FRP tank, pump-motor set, suction delivery valves & pipe, all instrumentation viz. Pressure switch, pressure gauge, level indicator, etc, starter panel (including one main pump & one trimmer pump shall have VFD), cables, etc. FRP Hydropneumatic Tank with inter connection and suitable connections such as inlet, drain, outlet, pressure gauge, union connection, isolation valve, outlet pipe (to be connected to the header pipe), pressure switch, outlet valves, mounting pads, etc. with all accessories. vertical booster pumps directly coupled with the motor with SS casing, SS impeller, SS shaft and driven by 415 V AC, 3 phase, 50 Hz.motor running at 2900 RPM speed and shall be supplied with all accessories viz. strainer / dry run protection/foot valve, base plate, coupling, etc.complete. The scope shall also include suction & delivery piping & valves.( Flushing UGT to OHT Feeder )( Grundfos, ITT Lowara, or Eq.Make)Flushing Water Supply System :15.0m3/hr x 2 Nos. main Pumps ( 1 Working + 1 Stand by Set)Head : 30 mtr.Booster Tank : 100 ltrs. x 1 nos.

Suppying, installing, testing and commissioing of centrifugal monoset submersible pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., base plate, coupling, motor, starter panel, cabling up to panel, earthing,delivery & header pipes & valves etc., complete. (Water Transfer)( Grundfos, ITT Lowara, or Eq.Make)Capacity : 15 mtr3/hr.2 Nos. pumps ( 1 Working + 1 Stand by Set) Head:-30mtr.

DRAIN PUMPS (DEWATERING PUMP) Supply, installation, testing & commissioning of Submersible type drain sump pump having CI casing & SS impleller. The scope shall also include necessary PVC piping with delivery isolation valve & NRV with starter panel, etc. complete. (for Water Body, Basement Wash Area Drain ) ( Grundfos, ITT Lowara, or Eq.Make)Capacity : 10 mtr3/hr. ( Solid Handling Capacity up to 32-50mm)( 1 W + 1 S)Head : 10 mtr.

TERRACE LVL. R.O PLANT ; Supply, installation, testing & commissioning of 1000 ltr. /hr. R.O.plant with including PVC RO. Water Tank of 2000 LTR. CAP. Sintex make 3 layer and Product water Tank also Included in 3 layser type, The R.O.plant including of primary & seconadary tratent with on line U.V. fultration along with built in booster pumps all intercnnectio piping, supports and valve and other electrical requirment ,safety valve, air valve, drain arrangement, all insturumentation, base frame, necessary electrification, etc. complete for Drinking Water supply. ( Pentair, Power H2O,Ion Exchange, Tharmex, Make) Capacity : 1000/hr. R.O.plant complete job. Inlet Water Quality :- ( Quality To Be Chq.)( As per Bore Water Test can be done by bidder.)Flow Rate of the System :- 1000 ltr/hr./ Feed Flow Rate : 2000 LPH/ Product Flow Rate : 1000 LPH/ Reject Flow Rate : 1000 LPH/ Operating Pressure : 12-13 kg/cm2/ Recovery : 50% to 70%

WATER COOLER ; Supply, installation, testing & commissioning of S.S. storage type water cooler with inbuilt with on line U.V. fultration along with built all intercnnectio piping, supports and valve and other electrical requirment ,along with inbuilt storage tank with nessesarry accessories, safety valve, air valve, drain arrangement, all insturumentation, base frame, necessary electrification, etc. complete for Drinking Water supply. ( Voltas, Blu star, Power H2o Make) Capacity : 50 storage capacity. Complete as directed by site eng. incharg.

WATER COOLER ; Supply, installation, testing & commissioning of S.S. storage type water cooler with inbuilt with on line U.V. fultration along with built all intercnnectio piping, supports and valve and other electrical requirment ,along with inbuilt storage tank with nessesarry accessories, safety valve, air valve, drain arrangement, all insturumentation, base frame, necessary electrification, etc. complete for Drinking Water supply. ( Voltas, Blu star, Power H2o Make) Capacity : 150 storage capacity. Complete as directed by site eng. incharg.

STP PLANT :-Supply, installation, testing & commissioning of Sewage Treatment Plant with all electromechanical equipments, interconnected piping, valves, pumps, instaruments, gauges, electrification like panel, starter, cabling, earthing, etc. & all accessories required as per specifications. Design & Construction of RCC tanks including collection & treated waste water tank min 1 day storage req. with manhole cover & all accessories required to complete the job ,Operation & maintennace of Sewage Treatment Plant with all spares, tools, consumables, hardwares, testing, man power, etc. Connection underground sewage line to STP with required civil works of collection tank of 25m3 other civil structure of the pump room of the plant, equilization tank, areation tank etc all included in the scope., piping work & accessories,Connection of Treated waste water overflow to the nearest drain with required civil, piping work & accessories,Connection of Treated waste water overflow to the nearest drain with required civil, piping work & accessories,Bypass connection of STP to required drain point with required civil, piping work & accessories (Envisol/ Ion Exchange, Sintex & Power H2o Make)Capacity : 135 cu. mtr./ per day ( OUT Put Perameter as Per Flushing & Irrigation Reuse water req. quality , Pollution Control board Laws)

SEPTIC TANK SYSTEM:-Constructing water tight brick masonry Septic Tank with second class bricks in cement mortar 1:4 (1 cement :4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside and out side plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement & FRP. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), two brick masonry baffle walls each of 1200 mm depth & third one 1200 mm deep each of 115 mm thickness, 3 No. FRP heavy duty double seal manhole cover with frame (internal size 600 x 600 mm & total weight of cover & frame to be not less than 38 kgs) including excavation, backfilling & disposal of surplus earth complete as per standard design.( The Size of the Septic Tank :- 7.00mtr x 2.00mtr x 1.20mtr liquied depth the over all depth will be 3.20mtr.)

SOAK WELL SYSTEM:-Constructing honey comp brick masonry Soak well with second class bricks in cement mortar 1:4 (1 cement :4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), FRP. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), 1 No. FRP heavy duty double seal manhole cover with frame (internal size 600 x 600 mm & total weight of cover & frame to be not less than 38 kgs) including excavation, backfilling & disposal of surplus earth complete as per standard design.( The Size of the Soak well :- 3.00mtr x 7 to 9.00mtr liquied depth.)

BORE WELL:-Supply installation, testing, commissioning of Bore well submersible pump to be installed in the tube well of required indicated capacity and head as per relevant IS for Bore water lifting with suitable submersible vet type, water cooled, squirrel case motor conforming to IS 9283, working of 3-phase, 50Hz +/- 3% 415 VAT +/- 10%, AC supply 2900 RPM synchronous speed with 10mtr. copper conductor flat cable from pump to starter panel with cables and termination ( all supports clamps pipe fittings mechanical seal, bearing, bush, strainer, etc. comp., Casing C.I., S.S. CF8M impeller, bronze casing, wearing and bearing bush, TC mechanical seal, S.S. bearing, S.S. shaft with sleeve, S.S. strainer, and M.S. morter along with water guard, single phase preventor with all cables of appropriate size control and instrumentations, switches, testing, and installation along with testing. The scope shall also include delivery isolation valve & NRV with PVC piping (400 dia Drill well @200mm dia MS. heavy class pipe : BORE WELL) Assume 225 TO 250 mtr depth) ( 20 TO 25 MTR CU. PER HR. OUT PUT FLOW RATE with potable water quality ) (15 TO 20HP PUMP.)

PUDDLE SLEEVES:-Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. 200 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,150 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,100 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,80 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,50 mm pipe dia x 450mm length

PART-E:- GAS PIPING : -Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor.(A) 15mm (upto 10 ton)

Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor.(B) 20mm (upto 10 ton)

Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor.(C) 25mm (upto 10 ton)

Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor.(D) 32mm (upto 10 ton)

Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor.(E) 40mm (upto 10 ton)

Providing and fixing Gun metal check fullway wheel valve.(A) 15mm dia.

Providing and fixing Gun metal check fullway wheel valve(B) 20mm dia.

Providing and fixing Gun metal check fullway wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check fullway wheel valve(D) 32mm dia.

Providing and fixing Gun metal check fullway wheel valve.(E) 40 mm dia.

Providian’s Escape Sigane:- Photoluminescent rigid plastic, 2mm thickness, printed on high quality glass paint with UV resistance, 5 year warranty, material used-non radioactive, non-phophorous, non toxic and lead free. Available in different types & sizes, time after removing the light source (in minutes):- 60 minutes, luminescent intensity(milicandelas*per square meter-mcd/sqm):30 mcd/sqm. Luminescent intensity greater than 0.32 mcd/sqm, period of light decay* (in minutes) :3100 (1) “Fire Exits” ( Size 365 x 119 x 84 mm or nearest )

(2)Fire exit signs of standard size ( Size 450 x 200 x 84 mm or nearest ) (photoluminous type.(glowing in dark type)Providing and fixing portable fire extinguishers of approved make ISI marked of following Capacity at the places shown on Drawing & mentioned in CFO letter

Providing, fixing, testing and commissioning of below Auto Glow Signages. In Case of Fire do not use Lift ,Use Staircase 8"x 8"

(1) Providing and fixing 2kg. Stored pressure type, pressure gauge, gross weight 4.9kg, empty weight 2.9kg, can height 440mm, diameter 140mm, discharge time less than 9 sec., controllable discharge mechanism (squeeze grip with easy snap safety seal), range minimum 4 meters, applicable on class A,B and electrically started fire, very effective on class B fire, B Rating 144B, can construction: deep drawn & co., Mig welded , valve construction: Forging and Mechining, Internal coating of powder coating, sheet metal thickness: 1.60mm, 5 years warranty. with installer system with superior quality EPDM rubber hosepipe etc., complete. ( 2kg. Monnex Powder)

(2) Providing & fixing 4kg. Stored pressure type, pressure gauge, gross weight 7.4kg, empty weight 3.4kg, can height 480mm, diameter 160mm, discharge time less than 13 sec., controllable discharge mechanism (squeeze grip with easy snap safety seal), range minimum 4 meters, applicable on class A,B and electrically started fire, very effective on class B fire, B Rating 144B, can construction: deep drawn & co., Mig welded , valve construction: Forging and Mechining, Internal coating of powder coating, sheet metal thickness: 1.60mm, 5 years warranty. with installer system with superior quality EPDM rubber hosepipe etc., complete. ( 4kg. Monnex Powder)

(8) Providing & Fixing four bucket stand along with bucket compete.

Providing and fixing Trolley type foam fire extinguishers cap. 50 liters. capacity

Providing and fixing Trolley type Co2 gas fire extinguishers cap. 9 liters will be provided for transformer area.

FIRE WET RISER SYSTEM :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., Note : The piping installation has to be put to hydraulic test to1.5 times Working pressure before applying paint or pipe coating and wrapping etc. Complete. (1) 150mm (Wet Riser hydrant )

FIRE WET RISER SYSTEM :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., Note : The piping installation has to be put to hydraulic test to1.5 times Working pressure before applying paint or pipe coating and wrapping etc. Complete. (2) 100mm

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve, check valve, strainers etc. (1) 150 mm diameter

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve, check valve, strainers etc.(2) 100 mm diameter

Fire hydrant system supplying installing, testing and commissioning of 63 mm diameter (2.1/2”) N.B. hydrant Single outlet gun metal hydrant valve with flange, inlet, stop valve, spindle and cast iron han wheel. It has a female instantaneous outlet with blank cap and is hydrostatically tested to 21kgf./cm2 pressure having a flow rate of 900 LPM at 7 kgf/cm2 of pressure with blank cap and wheel as per IS 5290 etc. complete.

Supplying installing , testing and commissioning of reinforced rubber lined RRL fire hose of 63mm diameter 15 m length as per IS 8423 binded with one set of male and female instantaneous gunmetal coupling as per IS 903 .

Supplying installing, testing and commissioning of 19mm diameter 36.50m length hose with rubber lining smooth borre, reinforced of natural/ synthetic fibers, a rubber cover finish shall be smooth , fluted or fabric marked with minimum thickness of 1.50mm and to with stand a working pressure of 10kg.sqcm. conforming & tested as per IS 444.

Supplying and fixing 2 way Fire Brigade service inlet of size 150 mm dia. with 2 No. 63mm (2.1/2") size GM male outlets (bronze male coupling) including metallic cover of mild steel and glass front, indicator plates, 150mm BFV and schematic mimic diagrams on metallic plate for easy operation as directed by Architect etc.complete to system.

Providing and fixing heavy quality Drain pipe & valves approved by site eng. In cherge etc. complete. For draining of sprinkler riser. (1) Ball Valve : 50 mm diameter, PN 1.0

Providing and fixing heavy quality Drain pipe & valves approved by site eng. In cherge etc. complete. For draining of sprinkler riser. (2) Drain pipe : 50 mm M.S.pipe & Fittings (class-C heavy duty : IS 1239)

Supplying Installing , testing and commissioning of Hose Cabinet made out 18gauge M.S. Sheet with double glass door with locking arrangement and painted with two coats of fire red enamel paint at outer ise of the Box and two coats of white enamel paint at inner side of the box is to accommodated 2 nos., of fire hose box 20" x 24" x 10" complete.

Providing, fixing, testing and commissioning of MS air cushion tank on top of each riser fabricated from 6mm thick MS plate, 200mm in diameter and 1200mm in height and dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock.

Supplying Installing , testing and commissioning of Gun metal branch pipe size of 63mm diameter x 19mm diameter as per IS 903 complete

Supplying and fixing specially designed gunmetal orifice plates on hydrant outlets of landing valves including distant pieces of suitable size for adjustment of delivery pressure of 3.5 kg/ sq.cm as required by LPA complete with necessary companion flanges, nuts, bolts, gaskets etc. complete.

Flow Switch on 80 mm Diameter pipe

Supplying Installing, testing and commission of Hose reel cabin M.S. Pressed reel 600mm diameter swinging type motion which allows a 180deg. Swing and conforms to IS: 884/85.

Supplying Installing, testing and commission of reinforced Rubber line RRL Fire hose of 63mm diameter 15m. Length aas per IS 8423 binded with one set of male and female instantaneous Genmetal coupling as per IS 903.

Wrapping and Galing of U/G pipe line work includes one coat of anti corrosion paint ( Black) and two coats of Bituminous cloth. (1) 150mm

Wrapping and Galing of U/G pipe line work includes one coat of anti corrosion paint ( Black) and two coats of Bituminous cloth. For M.S.pipe & Fittings (2) 100mm

Supplying and fixing specially designed gunmetal orifice plates on hydrant outlets of landing valves including distant pieces of suitable size for adjustment of delivery pressure of 3.5 kg/ sq.cm as required by LPA complete with necessary companion flanges, nuts, bolts, gaskets etc. complete.

MAIN FIRE PUMP ROOM ,TANK AND ACCESSORIES :- Supplying installing testing and commissioning approved make centrifugal pump end suction type couple to eclectic mortar of suitable HP, Fitted on a common base frame and rated for fire duty, Including 2 nos. pressure gauge fitted on suction & delivery side of the pump. the pump shall run on 400/440V, 3ph, 50 hz electric supply, duty of pump 2280 LPM, @ 55 mtr head, control panel shall be specification . ( cost of control panel is not included)

Supplying installing testing and commissioning of fire hydrant multistage pump capable of delivering 2280 LPM, @ 55 mtr head coupled to water cooled diesel engine of adequate HP. It shall be fitted with radiator on a common base from which complete ancillary units such as cooling system, non return valve, Y strainer, fuel tank of adequate capacity, pressure gauge , pressure switch, control panel shall be as per specification ( cost of control panel is not included)

Supplying installing testing and commissioning electrically driven jockey pump of capacity 180 LPM at 55mtr head with all the necessary accessories viz., pressure gauges etc, operating on 3PH 50 hz, 400/440 VAC supply including foundation, bolts etc. complete control panel shall be per specification ( cost of control panel is not included )

Providing, fixing, testing and commissioning of precharged air vessel (size 450 mm diameter & 2000 mm height) for pressurization of hydrant / sprinkler system complete with adequate pressure switches (as per design / requirement) with valve.

Supplying and fixing 4 way Fire Brigade service inlet of size 150 mm dia. with 4 No. 63mm (2.1/2") size GM male outlets ( bronze male coupling) including metallic cover of mild steel and glass front, indicator plates,150mm BFV and schematic mimic diagrams on metallic plate for easy operation as directed by Architect etc.complete to UGR.

Supplying, installation testing and commissioning of approved quality ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc.,Note : The piping installation has to be put to hydraulic test to 1.5 times Working pressure before applying paint or pipe coating and wrapping etc. Complete (1) 150mm (Suction and discharge header)

Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc.,Note : The piping installation has to be put to hydraulic test to 1.5 times Working pressure before applying paint or pipe coating and wrapping etc. Complete (3) 80 mm

Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc.,Note : The piping installation has to be put to hydraulic test to 1.5 times Working pressure before applying paint or pipe coating and wrapping etc. Complete (4) 50 mm

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (4) 80 mm size

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (4) 50 mm size

Supply, installation testing and commissioning pressure switch assembly with following components (1) Approved pressure switches with required cable

Supply, installation testing and commissioning pressure switch assembly with following components (2) Ball Valve 50 mm diameter

Supply, installation testing and commissioning pressure switch assembly with following components (3) Ball Valve 20 mm diameter

Supply, installation testing and commissioning pressure switch assembly with following components (4) 20 mm diameter pipe as per specification, Providing and fixing of M.S/ G.I. Pipe.

Supply, installation testing and commissioning pressure switch assembly with following components (5) 50 mm diameter pipe as per specification, Providing and fixing of M.S./ G.I. Pipe.

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 95 sq.mm

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 10 sq.mm (cable from pump room to terrace for booster pump)

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 16 sq.mm (cable for jockey pump)

Providing and fixing in position copper cable end termination glands for above mentioned cables 3 core x 95 sq.mm

Providing and fixing in position copper cable end termination glands for above mentioned cables 3 core x 10 sq.mm (cable from Booster Pump to terrace Remort Panel )

Providing and fixing in position copper cable end termination glands for above mentioned cables 3 core x 16 sq.mm (cable for jockey pump)

Providing, installation, testing, & commissioning of Remote Panel for fire fighting terrace pump with push buttons for manual operation (the remote panel shall be located at ground level) all complete.

Supplying, laying and connecting of following size 1.1 kV grade copper conductor armoured control cable on wall or on existing cable tray with clamping, dressing or drawn in existing ducts all as required (For remote panel for fire fighting terrace pump). 3 core x 6 sq.mm

Providing and fixing fire retardent / extinguishing electrical insulated synthetic mat of 5mm thick ±10% conforming to latest BIS doc no.-ET-02(5440) meeting requirements of IS 3043 / IS 5216 (Part I, II & III), IS 8437 & IEC 479 suitable for all voltages not exceeding 3.3 KV AC supply and having minimum width of 1000mm ± 20mm and including supply of required quantity of adhsive / compound and fixing the same at site as per site requirement.

Fabricating and installing following size of perforated G.I.cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders including painting, etc., as required. 150mm width x 50mm depth x 1.6 mm thickness.

Providing & fixing 25 mm x 5 mm G.I. Strip in on surface or in recess for connections etc as required.

Providing & fixing 25 mm x 5 mm G.I. Strip in 40 mm dia GI pipe from earth electrode as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

TERRACE (BOOSTER) PUMPS ,TANK ,PIPING AND ACCESSORIES :- Supplying installing testing and commissioning electrically driven terrace pump of capacity 900 lpm, at 35 mtr head with all the necessary accessories viz., pressure gauges etc., operating on 3ph 50 hz, 400/440V ac supply including foundation, bolt etc., and complete control panel shall be as per the specification 87.

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc. (1) Size 100 mm size(for jockey pump suction)

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc. (2) 80 mm size

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc. (4) 50 mm size

Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (1) 100mm

Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (2) 65mm

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (1) 150 mm dia.

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (2) 100 mm diameter

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (3) 80 mm dia.

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (4) 65 mm diameter

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (5) 50 mm diameter

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (6) 40 mm dia.

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (7) 32 mm diameter

SPRINKLER PROTECTION (Suppression system) :- Supplying, installation testing and commissioning of approved quality G.I..pipe & Fittings ( class-B) conforming to as per IS 1239 such as tee, elbows, check nuts, flangeer, nipples etc., including cutting welding, trending fixing on walls, ceiling (using 41- tech pipe/ M.S. Angle supports work includes two coats of metal primer and two coats of red enamel paint etc., (8) 25 mm diameter

Supplying Installing , testing and commissioning of approved make 15mm diameter sprinkler bulb pendent/ wall mounted type designed to operated 68 degrees centegrad make Tyco/HD Fire complete ( color code of bulb liquid inside glass bulb type pendent as per IS 9972: 57 deg. C. orage , 68 deg. - Red, 79de. C. -Yellow, 93 deg.C.- Green, 141deg. C. - Blue, !82deg. C - Mauve, 227/260 deg.C.- Black)Make and quality to operate at 68 degrees c.etc. complete. Note : If space between slab & false ceiling is 800 mm & more, upright sprinklers to be provided by Contractor

Providing ,fixing, testing ,commissioning approved make flow switche on 80 mm supply line for connecting to main fire alarm panel operating at 24-V at BMS room/security room including 2 core 1.5 sq.mm cabling,

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (1) 25mm diameter (Drain Valve)

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (2) 100mm diameter Gate Valve

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (3) Ball Valve 20 mm diameter ( test drain)

Supply and installation, testing and commissioning of hydraulic allying operated sprinkler cabit valve with water meter gong bell and trims as required, pressure gauges, drain valve, ball valve , check valve, strainers etc., (4) 150 mm ALARM VALVE with all accessories like motor gong test valve etc

Rossete Plate:-Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1200mm

Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-15 / sq. cm.

Providing & fixing 25mm dia gunmetal inspecting & testing assembly with ball valve(3 nos.), gunmetal sight glass, by pass valve & connected to drain line.

Supplying, Installation, Testing and commissioning of 2 C X 1.5 Sqmm Copper Armoured for Flow Switch Cabling from Announciation panel

Supplying, Installation, Testing and commissioning of Annunciator panel for flow control switch, providing Audio/Visual indicating of actuation of automatic sprinkler system for each zone complete as per specifications with provision for 3 zones (2 working and 1 spare for future). 'Indication of zone fire, 'Indication of zone fault, 'Fire/Fault hooter, 'Alarm cancel for fire/fault, 'Battery for emergency

Manual Fire Alram System. Providing, fixing, testing and commissioning of Manual Call Point.

Providing, fixing, testing and commissioning of Hooter

Providing, fixing, testing and commissioning of Conventional Fire Alarm Panel 12 Zone

Providing, fixing, testing and commissioning of 2 Core X 1.5 Sqmm Flexible copper Cable with PVC Conduit.

Providing, fixing, testing and commissioning of 3 Core X 1.5 Sqmm flexible copper Cable with PVC Condiut.

On - Off Pump Trigger System. :- Providing, fixing, testing and commissioning of On -Off Switch.

Fire Resistant Door Double Leaf Hinge Type (2 Hour Fire Rated) 1.00 mm thick GI Sheet cladded 40mm thick shutter complete with GI frame (Single Ribet – Frame Profile 100 x 57mm) made from 1.20mm thick GI Sheet & Fixing arrangements AS PER BS 476 PART- 20 & 22 & IS: 3614 Part - II for Integrity, Stability.Door Size: 2000mm (W) x 2100mm (H) Including below Accessories S.S. Ball Bearing Hinges- 6 Nos Vision Panel with Fire Glass of Size: 200 x 300mm - 2 Nos Heavy Duty Door Closer - 2 Nos Heavy Duty Door Closer - 2 Nos Panic Exit Device for Double Leaf Door - 1 No. External Trim Bar (Panic Latch) - 1 No.

ADDITIONAL WORK:- Core Cutting in RCC wall, beam, columns and roof as required locations of required size & depth and repairing , making it goods complete . Size 40mm to 80mm dia ( avarge depth 200)

Core Cutting in RCC wall, beam, columns and roof as required locations of required size & depth and repairing , making it goods complete :- Size 100mm to 200mm dia ( avarge depth 200)

Providing and fixing cast iron following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 200mm dia y strainer in main suction header

Charges for liasoning with CFO and getting all approvals and permissions & NOC 's required for fire fighting at various stages & after completion of the project.(All official and receipted payments would be submitted and Reembursed)

Point Wiring Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. with medium class Rigid PVC pipe and accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. with medium class 25 MM DIA Rigid PVC pipe and accessories

Primary light point controlled by one SP MCB ( Same as above item but controlling with SP MCB )

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire

Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 4.0 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make with concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Providing & erecting Switch board for Computer or electric apparatus consisting of following items in single board erected on PVC / Metal board with 3 mm thick PC (Polycarbonate) / Acrylic sheet erected as directed 1 no. 6A/16A universal plug-switch combined. 4 nos. 6A Switch 4 nos. 6A 5 pin Plug For Modular Type Accessories

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness

MAINS : ( not for Point wiring ) Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. Supplying and Laying of 4 nos. of 10 sq mm Cu. FRLS flexible wires with 2 nos 4 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 4 nos. of 6 sq mm Cu. FRLS flexible wires with 2 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 4 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS flexible wires

Distribution Board Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 43 of specified make. Distribution Board-VTPN Supply, Erecting, testing and commissioning of only VTPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 TPMCB as outgoing per phase (i.e. 8 way VTPN D.B.)

Supply, Erecting, testing and commissioning of only VTPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 4 TPMCB as outgoing per phase (i.e. 4 way VTPN D.B.)

Distribution Board-TPN Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 SPMCB as outgoing per phase (i.e. 12 way per phase D.B.)

Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.)

Distribution Board-SPN Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 8 SPMCB as outgoing per phase (i.e. 12 way D.B.)

Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 4 SPMCB as outgoing per phase (i.e. 8 way D.B.)

MCB providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Miniature circuit breaker single pole suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 6 to 25 A SP MCB

40Amp SP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 A DP MCB

40 A DP MCB

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 to 32A / 30mA/100 mA DP ELMCB

40 A / 100 mA DP ELMCB

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32A FP MCB

40 A FP MCB

63 A FP MCB

Approved make four pole moulded case circuit breaker having breaking Capacity ICU of 35KA. At 415 V, having normal current rating up to 125A. With fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all iternal connections & complete erected in existing 16 G.M.S. housing. ICS= 100% of ICU only.

Approved make four pole moulded case circuit breaker having breaking Capacity ICU of 35KA. At 415 V, having normal current rating up to 200A. With fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all iternal connections & complete erected in existing 16 G.M.S. housing. ICS= 100% of ICU only.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.

25 Amp DP Dinrail Mounted Contactor

SITC of 40 Amp DP Dinrail Mounted Contactor

SITC of IP65 Polycarbonate enclosure for DP MCB

SITC of IP65 Polycarbonate enclosure for FP MCB

SITC of IP65 Polycarbonate enclosure for FP MCCB

SITC Of 32A x 250 Volt single phase Power socket outlet point having IP rating of IP:65 at convenient location with MCB.for outdoor duty.

SITC Of 32A x 415 Volt three phase Power socket outlet point having IP rating of IP:65 at convenient location with MCB.for outdoor duty.

Cable Trench Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface proper. Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge. The width shall be as per requirement

Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks shall be provided.

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm stone metal duly plastered with necessary curing for pole muffing or any other purpose.

Providing burnt brick masonry with 1:6 cement concrete duly plastered including watering, stacking joint on exposed faces, rocking at joints on exposed faces and watering complete

Construction of brick masonry pulling chamber 450 mm x 450 mm inside clear size and depth up to 0.6 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 600 mm x 600 mm inside clear size and depth up to 0.60 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The Rate shall be inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 750 mm x 750 mm inside clear size and depth up to 0.75 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The Rate shall be inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 1000 mm x 1000 mm inside clear size and depth up to 1.0 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The Rate shall be inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Providing & fixing of the FRP recessed type cover with frame size 600 x 600mm size total weight of cover and frame to be withstand up to 25 ton. with including Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) 25 ton Cap. Recessed type cover( Cover-600 x 600mm ) ( Frame:- 812 x 812mm)

Providing & fixing of the FRP recessed type cover with frame size 600 x 600mm size total weight of cover and frame to be withstand up to 25 ton. with including Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) 40 ton Cap. Recessed type cover( Cover-600 x 600mm ) ( Frame:- 812 x 812mm)

Cable Tray Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray should be bended as per IS 2062/1079 shall be fabricated of double bended channel section longitudinal members with single bended Channel section. Rungs of members welded to the base of tha longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. 900 X 100 X 2 mm Thick

600 X 100 X 2 mm Thick

400 X 100 X 2 mm Thick

Providing and fixing approved make Perforated C type cable tray. Made from CR sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. (2) 100 X 50 X 1.6 mm Thick

(5) 300 X 50 X 2 mm Thick

(6) 450 X 50 X 2 mm Thick

(7) 600 X 50 X 2 mm Thick

Fabrication Supplying , fabricating and installation of various sizes MS race way / junction boxes/clamps/hangers for Cable Tray, Light Fixture made out of specified size sheet/Angle/Flat/rod/ channel etc as per design with all necessary accessories like bend, junction boxes, coupler, Anchor fastener, Bolt Nuts, etc.. & work from MS structure for other work with anchor fastener of Hilti make and necessary hardware with necessary welding has to be done to complete the job from ISA / ISMC / PLATE. The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant. Complete in all respect to be installed at any height with all necessary arrangements. Contractor has to complete the work up to satisfaction of Consultant

Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 400 sq.mm x 3.5c Al. XLPE Arm. Cable

300 sq.mm x 3.5c Al. XLPE Arm. Cable

240 sq.mm x 3.5c Al. XLPE Arm. Cable

185 sq.mm x 3.5c Al. XLPE Arm. Cable

150 sq.mm x 3.5c Al. XLPE Arm. Cable

120 sq.mm x 3.5c Al. XLPE Arm. Cable

95 sq.mm x 3.5c Al. XLPE Arm. Cable

70 sq.mm x 3.5c Al. XLPE Arm. Cable

50 sq.mm x 3.5c Al. XLPE Arm. Cable

35 sq.mm x 3.5c Al. XLPE Arm. Cable

25 sq.mm x 4 c Al. XLPE Arm. Cable

16 sq.mm x 4 c Al. XLPE Arm. Cable

10 sq.mm x 4 c Al. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 6 sq.mm x 4 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 4 sq.mm x 4 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 6 sq.mm x 3 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 4 sq.mm x 3 c cu. XLPE Arm. Cable

Supplying & erecting XLPE (IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size 3 core 2.5 Sq.mm.

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 400 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 300 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 240 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 185 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 150 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 120 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 95 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 70 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 50 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 35 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 25 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 16 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 10 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 6 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 4 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 6 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 4 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 3 core 2.5 Sq.mm.

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor unarmored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass IP65 glands with earthing. 10 sq.mm x 4c Al. XLPE Un.Arm. Cable MV Switchgear & Power Panels (TTA as per IEC 61439) Supply, Unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning main L.T. panel board, fabricated from M.S. sheet & folded channel totally enclosed cubical type compartmentalized. Scope Covers Unloading at Site, Store in Weather Proof Condition, Shift to the Location Basement / GF / FF, Grouting, Installation, Testing & Commissioning complete in all respect & As per the instruction of Architect / Consultant / Engineer Incharge. Scope also covers Co ordination with Panel Manufacturer. Design, fabrication, assembling, supply, installation , testing of Panels for 415 V, 3 phase, 50 Hz, 4 wire power supply system. Panels shall be fabricated out of 2 mm thick CRCA sheet steel in cubical formation, compartmentalized in Form 4b Construction, floor mounted, free standing and shall be dust and vermin proof. 3 mm thick cable gland plate, shall be provided both at the top and the bottom of the panel. All large panels shall be provided with lifting hooks. Distribution panels shall be fabricated in accordance with the specifications.Note : Panel vendor has to provide Surge Protection at every stage of the Distribution. 1) Supporting rigid steel framework. 2) Cubicle type, 14 gauge CRCA sheet steel enclosed. 3) Complete with interconnections and distribution bus bars. 4) Proper bonding to earth. 5) Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram. 6) Providing cable clamps / supports within distribution boards cable alley.7) TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link. 8) All MCB’s shall be of minimum 10 KA breaking capacity. 9) The breaking capacity of MCCB’s are mentioned panel wise. 10) All motor feeders MCCBs shall be of motor duty. 11) Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5. 12) Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. a) IP 52 for indoor panels. b) IP 54 for Service area panels. c) IP 65 for outdoor panels.13) All MCCB’s shall be provided with operating mechanism for door interlock & with the roraty handle.14) Current density of aluminium shall be 1 sq mm for 0.8 amps for rated current of bus bars and current density of copper shall be 1 sq.mm for 1 amps for rated current of bus bars. 15) Tinned copper earth bus as specified in the BOQ / SLD shall be provided through out the length of each board. 16) All measuring instruments (Meters) shall be of digital electronic with LED of approved make and compatible with BAS. 17) All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire. 18) All panels shall have provision of the following: a) IP 55 for outdoor panels. b) Pad locking of MCCB’s handles in “OFF” Position. 19) Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided for BAS including space required for various transducers in Main Switch Board sections. Only transducers shall be supplied by BAS contractor.20) All the C.T.s should be auto short link type.21) All the MCCB's should be with rotary handle. 22) All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. 23) All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. 24) All PTs / control transformer shall be provided with centre tap earth secondary. 25) If Any descripancy found in SLD & BOQ, it should be brought in the notice of the Client / Consultant, Client / Consultant's decision will be final in case of any descripancy. 26) All outdoor panles should be provided with minimum 600mm height fabrication stand with all side 2mm thick M.S. powder coated sheet. 26) G.A. Drawing should be checked & Finalised by consultant before fabrication.

Light Fixture SITC of Any kind of Light Fixture with Basic Rate of Rs. 1000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 2000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 3000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 4000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 5000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 10000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 15000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 25000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 30000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 40000

Exhaust Fans : Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [A] 305 mm dia 900 RPM

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium blades with , canopy & 30 cms. down rod erected with 24/ 0.2, 3 core flexible wire with earthing.(fan colour shoud be Gray)

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Street Light Pole Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made by CNC filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than 10% of the length of pole for the given load“? Pole should be generally made as per the dimensional data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D 4923/01 . The size of pole and type of installation are as below (1) Suitable for base plate mounting single arm Bracket. [H] Overall length of 6 Mtr. Average Thickness: 7.5mm Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight of Pole 32 kg approx. (Without Base) Anchor Base (Size 300X300 & 18mm Th.) 1) 4 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping with foundation bolt with base plate with stiffener. 5) Spiral/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height & Pole Numbering as per Client / Consultant's instruction 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

Providing and fixing approved make Conical Poles (Medium Duty ) Made from CR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/4759. with required base plate as erected on existing foundation. The length of poles are as below. (F) 8 Mtr. Long 70 mm Top X 190 mm bottom dia, 3 mm thickness. 1) 4 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping with foundation bolt with base plate with stiffener. 5) Spiral/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height & Pole Numbering as per Client / Consultant's instruction 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

Providing and fixing approved make Conical Poles (Medium Duty ) Made from CR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/4759. with required base plate as erected on existing foundation. The length of poles are as below. (F) 9 Mtr. Long 70 mm Top X 205 mm bottom dia, 3 mm thickness. 1) 4 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping with foundation bolt with base plate with stiffener. 5) Spiral/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height & Pole Numbering as per Client / Consultant's instruction 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

High Mast Supplying, erecting, testing, commissioning approved make M.S. Polygonal High Mast Pole having following general Specification. (a) Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 & Hot deep galvanized minimum 65/86 micron (as per IS 2629 /1985) Lantern carriage with ring and rubber lines for erection of luminaries of suitable site. (b) Maximum telescopic section not more than four (c) Double drum gear pipe motorized winch with 6mm dia S.S. Rod (For 16 mtr and above size) (d) Approved make L.E.D. aviation light = 1 No. Lightening arrestor = 1 No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable Unarmoured. (e) Bottom most section suitable for mounting reversible motor and switchgears having door not more than 1400mm x 300mm with waterproof gasket & hinges & locking arrangement. (f) Pole structure comprises suitable size of reversible motor, cable and necessary switchgears with control panel. (g) bottom section shall have suitable size of thickness supports ribs foundation bolts nuts etc. (h) Item not comprises the cost of lanterns. (i) Necessary Cement Concrete foundation as per IS including testing & commissioning of the entire structure for following size of High Mast poles [9] High Mast 25 Mtr. TOP A/F 170 Mm, BOTTOM A/F 450 Mm, No. of Sec. No. - 3, Bottom Thickness - 4 mm, Middle Base Sec.mm - 3, Top Sec. - 3 mm, Size Base Plate -dia. 680 mm x 35 mm thick, Foundation Bolt Size M30 x 1000 mm, Qty - 12 Nos., Suitable for mounting Fitting of Light - 12 Nos.

H.T. Supply, Unloading, Shifting at site, installation, testing and commissioning of 11 / 0.433 KV compact package sub station comprising 11 KV 630 A, 350 MVA SF6 breaker as incomer & 1 nos. of 11 KV 630 A SF6 breaker outgoing with dual core CT & PT of appropriate rating for metering and protection, with 150 KVA, 11 / 0.433 KV Oil type transformer +/- 10 % off load tape change & LT panel consisting of 1 no. 630A 4 Pole MCCB of 50 KA breaking capacity with MCCB and Capacitor as per Specification as outgoing. All MCCB shall have Microprocessor based release unit with all kind of communicable accessories with metering as shown in the SLD . Package sub-station shall be complete as per specification. Metering must be as per the SLD. All Load Managers must be with communication Port & Vendor has to provide the software for the same.

SITC following size 11 KV grade XLPE aluminium conductor armored cables laid over MS supports in existing trenches. 3 C x 240 sq.mm 11 KV XLPE cable (between metering panel room to HT panel and HT panel to transformers).

Supplying and making cable end terminations for the following size of 11 KV grade, XLPE aluminium conductor armored cable including termination kit complete heat shrinkable sleeve etc. 3 C x 240 sq.mm 11 KV XLPE cable (Outdoor)

SITC of following 1100 volts grade PVC insulated sheathed copper conductor armored control cables in existing trenches cables trays, clamped on wall with suitable saddles, fixing bolts, including testing and commissioning. 12 Core 4.0 sq mm PVC insulated copper conductor armored control cables

SITC of Cable end termination of the following PVC insulated sheathed aluminium conductor armored cables of 1100 volt grade including supplying and fixing of crimping lugs. Double compression glands with earthing provision and cable sockets 12 Core 4.0 sq.mm Control cable

AMF Panel Providing & erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below: 1) Power module: A pair of electromechanically interlocked contactors (for mains & generator) Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs. 3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V belt failure. 4) Indicators with alarm Load on generator. 5) Indicators Load on mains Engine fails to start . Emergency stop battery charger. The AMF Panel of following capacity (D)AMF Control Panel for200 KVA/250 KVA3 phase DG Set

UPS Supplying and erecting approved make online Un-interruptible Power Supply system with IGBT Based rectifer and Inverter & sealed maintenance free batteries. Three phase Input and Three Phase output with Inbuilt Isolation transformer with 0.9 load power factor with battery, over under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following capacity & with Following size of batteries for 30 Min Backup (Minimum 8160 VAh) 10 KVA UPS with 34 AH, 20 Nos. Battery Certification : BIS (Including Five year free maintenance with guarantee)

Lightning Arrestor Lightning Air Terminal with adopter : Supply of New Generation Advanced External Lighting wide area protection Air Terminal working as per Latest IS, IEC and NFA. minimum radius 65 mtr. The lightning air terminal shall be configured as a spheroid surrounding an earthed central finial. The central finial shall be elevated above the spheroid and it should be sharp pointed. The lightning air terminal must not have separate panel isolated by rubber or plastic material. It should be maintenance free type and made of non-corrosive materials including lightning counter.

Earthing Supplying & erecting funnel type earthing having earth plate of following size burred in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per drawing) with following specification with 60 x 60x 0.315 cms. Copper earth Plate

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For pole)

Earth wire/strips : Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. Supplying and Laying mains with 1 no. of 6 sq mm Cu. PVC insulated FRLS flexible wire ( Green Color Only )

SITC of Water Tight Junction Box With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight Glands only )

Telephone Distribution Providing and installing of all conduiting and structured cabling for telephone system including providing and fixing of the following: 1) All necessary specials and fittings 2) Approved cover plates for inspection, junction and outlet boxes. 3) 2 mm thick outlet boxes (MDF) and junction boxes. 4) All fixing accessories such as clips, nails, screws etc. 5) Providing and fixing approved saddles, hooks and grouting the same as required, in the case of all exposed conduit work. 6) Embedding conduits and accessories in wall, floors etc. during construction and / or cutting chases and making good as necessary in the case of all concealed conduit work. Supply and installation, testing and commissioning following size telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 20 pair Krone type tag block

10 pair Krone type tag block

5 pair Krone type tag block

PVC & HDPE Conduits Supply & laying of 25 mm dia. rigid PVC conduit of 2.0-2.2 mm thick heavy gauge with all accessories.

Supply & laying of 40 mm dia. rigid PVC conduit of 2.1 -2.3 mm thick medium gauge with all accessories.

EPABX SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP program me through Analog telephone digital key from Ethernet, public address cord, shall have unrestricted simultaneous dialing facility, QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit dialing of any two external number, Once only ring device, Boss/Secretary-Do not disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing with following capacities [C] No of Extension 48, No of Junctions 9, 8 Port IP Resource in-built, 4 Port Web base Video Conferencing, No of expandable ports : 128, Operators Console - 01 Compatible : ISDN

Supplying & erecting push button type telephone instrument having speaker phone Caller ID & hands free dialling system & 30 memories with display system

providing and erecting IP Phone with display with all IP system supported

Telephone Point Wiring Supply and laying of specified make 0.51 mm dia Tinned copper telephone wire of specified make to be done in prelaid PVC pipe of 25 mm dia/raceway of specified make, but without the cost of pipe or raceway. (the wire is to be drawn from Krone connector of respective area to outlet point ) 5 pair telephone wire

10 Pair Telephone Wire

Supply, Installation, Testing And Commissioning of Solid Cable Cat 6, 4 pair, UTP.

Telephone Outlet Point SITC OF PowerCat 6 DataGate Jack, 568A/B - Yellow with Dust Cover / Blank/ One Telephone Point to be done with Cat -6 Information outlet Socket, Back Box, Face Plate for all telephone point. Average Length to be considered as 50 Meter. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost. 20 Years of Certification is required. Test reports of Level-4 Scanners only.

SITC OF DG+ Jack (Diecast)Cat6A 568A/B, Shtd- Black (Information Outlet for Data) with Faceplate, back box CAT-6A standards. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost. 20 Years of Certification is required. Test Reports of Level-4 Fluke Scanners Only.

SITC OF 24 Port Layer 2 Fully Managed Network Switch with 24 10/100/1000Base T Ports and 4 GE SFP Ports. Include Limited Lifetime Warranty.

Supply, installation, testing and commissioning of 24 Port loaded Patch Panel

Supply, installation, testing and commissioning of Patch Cord-1m

Supply, Installation, Testing and Commissioning of Equipment rack / Console as per requirement

CCTV Supply, Installation, Testing & Commissioning of Network TDN IR Mini Dome Camera, 1/2.9" CMOS, 5 MP @ 25fps, Triple stream, Min. Illumination required 0.25 lux @ color, WDR 120dB, Min. Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/5; Adavance Video Compression technology such as H.265 / H.264 / MJPEG, 3mm~8mm, MFZ lens, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Camera Tampering, Intrusion/Object enter area; 4 nos Privacy Mask, Smart IR with upto 30m IR distance, AES-128/256, PCI Data Security Standard compliance, 128GB SD card support, DC12V, PoE (IEEE 802.3af) (Class 2), IP 66, IK10, Having Operating temp range : –10°C to 50° C. Certifications: ONVIF Profile S, G compliant, UL, CE/EN, FCC Part 15 & RoHS compliant along with mounting brackets suitable for Cieling / Wall mounting & required accesories as per site requirement.

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN IR Bullet Camera, 1/2.8" CMOS, 5 MP @ 25fps, Triple stream, Min. Illumination required 0.05 lux @ F1.4 (color), WDR>120dB, Min. Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/30; Adavance Video Compression technology such as H.265 HEVC / H.264 / MJPEG, Smart Codec, 2.7-13.5 mm 5X motorized focus & zoom lens, P-IRIS, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Video Tampering, Intrusion, Loiter, Line crossing, Unattended object, Missing object, Face detection; 5 nos Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Stream encryption, AES-128/256, PCI Data Security Standard compliance, FIPS Chipset Built-In, 256GB SD card support with SD card encryption, Dual channel Audio G.711a / G.711 Mu / G.726, Alarm: 2 In/ 1out, In-built Heater; PoE+ (802.3 at) and 12V DC/24V AV; IP 66 / IP 67 / NEMA 4X, IK10, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, G compliant, UL, CE (EN 50130-4 & EN 55032) , FCC Part 15 & RoHS compliant along with mounting Brackets suitable for Pole / Wall mounting & required accesories.

Supply, Installation, Testing and Commissioning of Number Plate Recognition Camera with Ultra-low illumination technology, 1/1.8" Progressive Scan CMOS, 0.004 lux color @ F1.53, 0 lux B/W with IR LEDs on @ F1.53, Slow shutter, 6 MP 25/30fps, 4.1 to 16.4 mm/F1.4 Motorized VF lens with Smart Focus, H.265 and H.264/MPEG4, Triple-Stream, Support SD/SDXC Card up to 128GB, IP67, IK10, DC12V/PoE, up to 50m IR range, Bracket & junction box included, Smart Feature-setAudio/Alarm IO UL, CE, FCC & RoHS compliant and Cyber Security Complient.

Supply Installation Testing & Commissioning of Network Storage Manager(NSM) supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec. System proposed shall have scalability of 4 to 120 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF, Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity.

Supply, Installation, Testing & Commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's licenses upto 100 cameras & 3 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall support iLIDS certified Analytics like Licence plate recognition and intrusion/LoiteTrace.

Intel® Core™ i7-12th generation, 4.0 GHz or better, Xeon 11th Generation 4.4 GHz or higher, Minimum 32GB RAM, Minimum 512 GB separate SSD hard drive for OS, DVD-R/W, 6 GB/s SAS/SATA RAID Card, RAID 1, 5, 10. 2 NIC cards supporting network throughput of 256 Mbps/425 Mbps for Incoming/outgoing, Graphics Adapter - Intel®IRIS XE Graphics or equivalent for local client GPU rendering support, Windows Server 2019 (64-bit OS versions recommended), Microsoft SQL Express 2012. Video rated or Enterprise drive, 7200 RPM SATA/SAS recommended, Video Monitor Resolution- 1280x1024 pixels, 32 bit with keyboard and mouse. The NSM shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items, as required.

Supply, Installation & Commissioning of NVMS workstation/PC with minimum Intel Core i7-12th Generation, 3.4GHz, 8GB RAM, Windows 10 Professional (64 Bit) OS, DVD R/W, Integrated Intel HD graphics 530 and NVIDIA Quadro NVS 315 1 GB PCIE x 16 LP supporting 4 Monitors. The NVMMS shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, storage, accessories etc., civil, electrical works & peripheral items, as required as per specification in Annexure A at site of work inline with the Engineer in Charge instructions..

Supply, Installation, Testing And Commissioning of 55" 4k UHD resolution Monitor - 120 HZ for viewing the cameras

Supply, Installation, Testing and Commissioning of Equipment rack / Console as per requirement

SITC of HP 2530-48G-PoE+ Switch, 48 10/100/1000 PoE+ ports, 4 SFP ports 382W PoE+ (J9772A) + 1 number of SFP Module of Transceiver, MM, 850nm, 550m (J4858C)

Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 24 # 10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port.

Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 48 # 10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port.

Supply, installation, testing and commissioning of 24 Port loaded Patch Panel

Supply, installation, testing and commissioning of 48 Port loaded Patch Panel

Supply, installation, testing and commissioning of Patch Cord-1m

Supply and laying of PowerCat 6A U/FTP CM 4 Pair Cable, LSZH Sheath - Violet of specified make to be done in prelaid PVC pipe of 25 mm dia / raceway of specified make, but without the cost of raceway or pipe ( the wire is to be drawn from HUB \ Switch of respective area to outlet point ) with the cost of the crimping with material.

Supply and laying of Cat-6 STP LSZH UV outdoor cable in PVC conduit with termination as per TIA

Supply installation testing and commissioning of power amplifier 480 W power amplifier in a 3U high 19” housing, 70 V / 100 V and 8 Ohm outputs, 100 V input for slave operation on 100 V speaker line. Bosch LBD1938/00

Supply installation testing and commissioning of Voice Alarm Controller Built-in message manager and 240 W amplifier, Six‑zone outputs, 6 emergency and 6 business triggers, internal 16 MB flash ROM, Two BGM inputs,Two RC station connectors. Bosch LBB 1990

Supply installation testing and commissioning of Wall mount volume controller . Bosch LM1V36P

Supply installation testing and commissioning of High- End Low Noise Copper Speaker Cable 1.5 Sqm. PVC jacket Krystal

Supply installation and commissioning of Equipment Rack – 28U Designed As Per Site Requirement Elixer

Fire Detection System Supply, Installation, Testing And Commissioning of UL864, 10th Edition Microprocessor based 4 loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 250 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be compatible with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers.

Supplying, Installation, Testing and Commissioning of Network Repeater Panel with minimum 10" Color Touch Screen display with QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation.

Supply, Installation, Testing And Commissioning of UL Listed Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supply, Installation, Testing And Commissioning of Automatic printer capable for interface with NCS and provided with RS 232/RS 485 protocol port. It shall be standard cartage with 80 characters per line as per all requirements of technical specifications & contracts works.

Supply, Installation, Testing And Commissioning of UL268, 7th Edition Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL Listed Addressable Rate of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL listed Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device.

Supply, Installation, Testing And Commissioning of UL Listed Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

Supply, Installation, Testing And Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing And Commissioning of UL Listed Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installation, testing & Commissioning of Battery pack suitable for back up of 4 hours with charger in case of Alarm condition.

Supply, installation, testing & Commissioning of response indicator

Supply, installation, testing & Commissioning Fire Exit Signage boards with 3hrs battery backup

Supply & laying of 2 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Supply & laying of 4 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Miscellaneous Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. For 4.5 Kg Capacity, including maintaining/ renewal validity of all Co2 fire extinguisers up to the completion of O&M period

Supplying rubber matting of following thickness as per IS : 15652/IEC61111 4mm

Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be erected as per IS.

Providing printed instruction chart both in English and Gujarati and duly framed with front glasses, for treatment of person suffering from Electric shock

Providing the A0 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A1 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A2 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A3 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth for laying of cable. below ground / road surface for enclosing cable and back filling the same to make ground as per original. (A)50 mm dia

(B)90 mm dia

(B)120 mm dia

Liason / Follow UP with Supply Co. Filling the necessary application to supply co. following up and getting the supply filling the necessary test report to the supply co. inclusive. All official fees including security deposits will be paid by the client and out of pocket expenses shall be of contractor. 1. To get temporary power supply 2. To get the H.T. Connection 3. To get all approval from CEIG and supply company 4. To get Lift approval

Salvage Value to be paid to the government for the materials obtained from the demolition and dismantalling of existing delapidated building including sub-structure and super-structure and disposing off the dismantalled serviceable / unserviceable materials up to 5 km and above including all lead and lift and transportation etc. The demolition and dismantalling work shall be the responsibility and in the scope of work of contractor and cost what so ever shall be borne by then and materials obtained from it shall be the property of obtained by paying it salvage value. The work of demolition and dismantalling to be carried out and make ground level plain and clean without causing any damages to the existing utilities, services, near by govt. and private structure/ building and keeping all human safety etc. (The contractor shall quote salvage rate not below the Rs. 34,20,095 /-)

Jyoti Infratech Company