REPAIR TO ROAD INCLUDING ROAD FURNITURE IN HALDIGHATI LINES, MGs ENCLAVE IN ZONE-III AREAUNDER GE (S) JAIPUR

Amount

Repair to pot holes depth exceeding 30mm, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, but making good by applying tack coat at 5 Kg per 10 sqm putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 sqm blinded with 0.09 cum of stone chippering, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings) etc complete all as specified and directed

S&F in replacement solar cat eyes (studs) made of aluminium di-casted body, 100% waterproof, both side reflectors, designed according to IP 65 of size 125mm x 125mm x 25mm with shank not less than 60mm length, high efficiency mono crystalline solar panel (2.5 V/0.3 watt), one Ni-Mh or Ni-cd rechargeable battery (1.2 V/1600 MA) having six super bright LEDs with 10000 to 18000 mcd (millicandela) view distance upto 1000 metre and flush road bearing capacity 10 MT, fixing in road by drilling a hole and with epoxy hardener etc as per manufacturer’s instructions at the location etc complete all as specified and directed. Model:- “DHRUV in dark eye or equivalent in TATA BP/Gogia Plastic/Red Safe/Froniter/ Tata VPI as approved by GE.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 Sqm and depth exceeding 50 mm but not exceeding 100mm deep etc complete all as specified and directed.

M&L for preparing surfaces of road by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 5 kg per 10 sq metre complete all as specified and directed.

M&L for premix bituminous macadam mixed laid with mechanical paver and 8 to 12 tonne power roller and compacted to required gradient and camber (Consolidated thickness 75mm or less) with paving bitumen 4% binder (viscosity grade VG-30) contents complete all as specified and directed. NOTE:- (i) Work shall be executed as per designed mix (job mix formula) approved by GE. (ii) If the bitumen content as per design mix found to be less than 4%, it shall be recovered at the rate of Rs 50/- per Kg for short of bitumen. If bitumen content found to be more than 4% as per design mix same shall be provided without any extra cost to the Govt.

M&L M&L for preparing black top surfaces of road by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 5 kg per 10 sq metre complete all as specified and directed.

M&L for preparing black top surfaces of road by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc, applying priming/tack coat with bituminous primer (VG-10) viscosity grade @ 5 Kg per 10 Sqm etc and laying bituminous premix asphaltic semi dense concrete 30 mm thick (consolidated thickness) with mechanical paver, mixed at hot mix plant transported to site in tippers, chipping mixed with 5.5% of paving binder (VG-30) viscosity grade, rolled to uniform smooth surface with 8 to 12 tonne power roller and compacted to required camber and gradient complete all as specified and directed. NOTE:- (i) Work shall be executed as per job mix formula approved by Accepting Officer. (ii) Bitumen content as per design mix is found to be less than 5.5%, the short of bitumen shall be recovered at the rate of Rs 50/- per Kg and no adjustment shall be made if the bitumen content as per design mix found to be more than 5.5% same shall be provided without any extra cost to the Govt.

S&F in repair delineator with two high performance 100mm Dia reflectors and two rectangular reflectors of 70mmx23mm are fixed on both sides of Guide Post. The body of Guide Post is moulded in ABS plastic and it is fixed on powder coated steel pipe of 1010 mm long embedded in PCC (1:2:4) type B-1 using 20mm graded stone aggregate( Size of block 30cmx 30cmx30cm) complete all as specified and directed. Make: Dark eye or equivalent in TATA BP/Gogia Plastic/Red Safe/Froniter/Tata VPI as approved by AGE(I) /GE

Supply and fixing in repair convex mirror 800mm to 1000 mm Polycarbonate Traffic mirror unbreakable round wide angle driveway mirror, with adjustable brackets and nuts bolts for installation and mounted on 60/75 mm dia mild steel pipe of 1000 mm height duly powder coated including embedding in PCC 1:2:4 ( 300x300x300mm) type B1 etc complete all as specified ad directed. Make: ABS Industry or equivalent in Dark eye/TATA BP/Gogia Plastic/Red Safe/Froniter/Tata VPI as approved

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thickness below or above ground level and remove the same outside of MD land complete all as specified and directed.

M&L for cleaning and preparing the road surfaces for road marking with reflective thermoplastic white 2.00mm thick road marking paint conforming to BIS 3262, laid through road marking machine in a layer painting lines, dashes, arrows, letters etc, width exceeding 10cm wide on roads, pavements with road marking paint, white or golden yellow of CRYSTALEX, using 5 Kg material per square meter by incorporating the white glass beads for reflectivity in 100 mm width etc, complete all as specified & directed.

M&L for 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base etc, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar and removal of same from outside MOD land complete all as specified and as directed by Engineer-in-Charge.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thick M-35 grade with grey cement and no pigment etc complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Manufacturing, supplying and fixing retro reflective Overhead informatory road signage and boards, made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTMD- 4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).

M&L for preparing of new concrete/plastered surfaces of any description over 10cm girth or width, not otherwise specified and applying one coat of synthetic enamel paint etc, complete all as specified and directed.

M&L for preparing of old concrete/plastered surfaces of any description over 10cm girth or width, not otherwise specified and applying one coat of synthetic enamel paint etc, complete all as specified and directed.

Schedule of Credit

Satish kumar and company

AMIT RISHABH BUILDERS PVT LTD

M/S Anil Enterprises

J.J.ENGINEERING