CERTAIN MISC REPAIR TO FURNITURE UNDER GE NARANGI

Amount

REPAIRS TO BED HARD TOP STEEL [ DRG NO: (FD/MAP/E6/08(R) ]

Removing the unserviceable plywood from Bed Hard and tightening all legs ,long rails and short rails of Bed Hard top Steel complete all as directed.

Removing the old welding spots from broken welding joints and re-welding in the same place as required. Thereafter preparation of old surface by sand paper No 50 and wire brush and apply one coat of synthetic enamel paint in Black colour over a coat of red oxide primer complete all as specified and directed.

Removing the existing unserviceable /broken ply wood top and supply and fixing new 12 mm thick BWR plywood top alongwith 06 in Nos Countersunk screws and washers on three stiffeners all as shown on Drg and as specified and directed Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

Removing the existing unsv shoes and S&F new PVC shoes in legs of Bed Hard as per existing pattern.

REPAIRS TO CHAIR VERANDAH [ DRG NO: (FD-359 & 256) ]

Removing the existing unserviceable/ plastic cane, re-canning of chairs verandah with 4 mm wide 0.5mm thick plastic cane complete all as specified and shown on drg.

Preparing the existing steel surfaces and panting with two coats of white synthetic enamel paint and providing new plastic shoes for chair verandah inclidung taking down old shoes complete all as specified and shown on Drg.

REPAIRS TO CHARPOY GI PIPE PLYWOOD TOP [ DRG NO: FD-220 ]

Removing the existing unserviceable ply wood from GI charpoy and supply & fix 12mm thick plywood, BWR grade, ISI marked alongwith two angle iron stiffeners 900x25x3mm with 08 Nos Nut Bolt complete all as specified and directed. Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

Removing the existing unserviceable / broken long rail 32mm dia and supplying and fixing new long rail for charpoy GI Pipe of Make : TATA/JINDAL/ASIAN .

Preparing short rail from broken long rail obtained from Sl item No 3.02 above and fixing for charpoy GI pipe complete all as specified and shown on drawing including removing the existing broken/ unserviceable short rail.

Preparing leg of GI Charpoy made from old long/short rail obtained from item No 3.02, and 3.03 above and welding 3mm thick base plate to the bottom of the leg and preparing MNF clamp holes as per existing and all as specified

Supply and fixing GI 3 way elbow 32mm bore,ISI marked, length not less than 65mm in each way including dismantling of old GI elbow.

Supply and fixing GI checknut, 5mm thick suitable for 32mm GI pipe pe including dismantling of unserviceable checknut.

CHARPOY HARD TOP [DRG NO: (FD/MAP-II/01) ]

Removing the old welding spots from broken welding joints and re-welding in the same place as required & denting and straightning of MS Pipes. Thereafter preparation of old surface by sand paper No 50 and wire brush and apply one coat of synthetic enamel paint in Black colour over a coat of red oxide primer complete all as specified and directed.

Removing the existing unserviceable /broken ply wood top and supply and fixing new 12 mm thick BWR plywood top alongwith countersunk screws bolted on the stiffners 06 in Nos all as shown on Drg and as specified and directed . Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

Repairs Book Case Steel [DRG NO: (FD-1028) ]

Removing unserviceable glass from shutters & Supplying and fixing new sheet glass of 5mm thick, plain, ordinary glazing quality conforming to the requirement of IS – 1761 of size 870 X 380 mm all as shown on drawing complete all as specified and as directed. Make: Modi Guard /Saint Gobain/Swastic.

Removing unserviceable handle & Supplying and fixing new chromium plated handle 100 mm long as per existing pattern complete all as specified and as directed.

Removing unserviceable locks & Supplying and fixing new locks 04 Nos in each Book case with duplicate keys all as per existing complete all as specified and as directed.

Preparing the existing steel surfaces by scrapping with sand paper and panting with one coats of two colour synthetic enamel paint one blue on body and off white on the shutters old shoes complete all as specified and shown on Drg.

REPAIRS TO CHAIR VERANDAH [DRG NO: (FD/MAP-II/06) ]

S & F new PVC seat made of PPCP material 4mm thick (Make : AMKO/SWASTIC/HARMONY) of Chair Verandah MAP including taking down the old worn out /broken seat all as specified as shown on drg and directed by Engr-in-Charge.

S & F new PVC Back made of PPCP material 4mm thick (Make : AMKO/SWASTIC/HARMONY) of Chair Verandah MAP including taking down the old worn out /broken Back all as specified as shown on drg and directed by Engr-in-Charge.

Preparing the existing steel surfaces and panting with two coats of white synthetic enamel paint and providing new plastic shoes for chair verandah & inclidung taking down old shoes complete all as specified and shown on Drg.

TABLE COMPUTER [DRG NO: (FD/E6/MAP/03) ]

Removing the existing TOP of table computer 3'x2' and S&F new top of size 900mmx600mm 18 mm thick prelaminated MDF board exterior grade both side decorative with standard PVC edging around and all as shown on drg.

Removing the existing any kind of unserviceable MDF Board Shelf and S&F new shelf of size 725x300mm made out of 18 mm thick Both side prelaminated MDF board exterior grade both side beich colour as per existing with standard PVC edging around and all as shown on drg.

Removing the existing any kind of unserviceable MDF Board Shelf and S&F new shelf of size 480x300mm made out of 18 mm thick Both side prelaminated MDF board exterior grade both side beich colour as per existing with standard PVC edging around and all as shown on drg.

Removing unsv existing keyboard tray of table computer and Supply and Fix new key board tray of size 480mmx450mm duly covered with PVC edging and one set of telescopic channel of size 300mm as per drg and as specified.

Removing unsv drawers of table computer and S&F new drawer of size as following:- (a) Front made of PLMDF Board Ext Gde of size 230x130mm (b) Sides made of PLMDF Board Ext Gde 300mmx90mm (c) Telescopic channels two in nos 300mm long (d) Bottom made of computer PLMDF Board Ext Gde 300mmx175 (d) Drawer End of size 140mmx90mm PLMDF Board Ext Gde

M&L for welding of thickness n.exc 6mm and length n.exc 2.5cm on frame of Table computer by gas welding wherever required complete all as specified and directed.

Repairs to Trestle store room Iron [DRG NO: (FD-86M)]

M&L for welding of thickness n.exc 6mm and length n.exc 2.5cm on frame of Trestle store room Iron by arc welding wherever required complete all as specified and directed.

Preparation of old painted surfaces of trestle No 50 sand paper and wire brush. Applying putty on the patch and rubbing with sand paper No 150 to make surface even. Thereafter applying one coat of red oxide primer and applying one coat synthetic enamel paint by spray painting of approved colour all as specified and shown on drawing.

REPAIRS TO CHAIR COMPUTER [DRG NO: (FD/E6/MAP/01) ]

Dismantling existing unserviceable PVC arm rest and S & F new PVC arm rest of best quality one Nos, one piece arm rest of size 24 cm x 6.4 cm x 3.3 cm shall be made out of polyurethane 76-85 shore ‘A’ Hardness and reinforced with MS insert scratch and weather resistant all as specified and directed.

Dismantling existing unserviceable seat of chair computer and S & F new seat 75 mm thick polyurethane foam moulded with density 50-55 kg per cubic mtr thick and hardness duly covered with tapesry cloth not less than 250/- per RM all as specified and as directed.

Dismantling existing unserviceable back of chair computer and S & F new seat 50 mm thick polyurethane foam moulded with density 50-55 kg per cubic mtr thick and hardness duly covered with tapesry cloth not less than 250/- per RM all as specified and as directed.

Removing of unsv pedestial assy of chair computer and S & F of new pedestial assy of 600mm pitch centre dia.

Removing unserviceable caster wheels of chair computer and S&F new caster wheels of chair computer complete all as specified and directed.

Removing unserviceable hydrolic shocker and S & F new hydrolic shocker of chair computer complete all as specified and directed.

REPAIR TO TABLE 900x600x760 MM W/O DRAWER [DRG NO: (FD 42/284) ]

Removal of unserviceable leg and S&F new leg made of 1st class hard wood for table Size complete all as specified & shown on drg.

Removal of u/s long stiffner under the top and S&F new long stifner made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s top and S&F new top made out of 18 mm thick prelaminated MDF board of size 900x600mm Exterior Grade both side laminated with teakwood beading 6mm thick half round all around, complete all as specified.

M&L for french polishing of complete table exposed to view except laminated portion complete all as per specified and directed.

REPAIR TO TABLE 900x600x760 MM WITH DRAWER [DRG NO: (FD-41,224,283) ]

Removal of unserviceable leg and S&F new leg made of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s top long rail and S&F new front top long rail made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s long stiffner under the top and S&F new long stifner made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of unserviceable drawer and S&F new drawer front and sides made out of prelaminated MDF board, 6mm thick (BWR Gde)plywood at the bottom of drawer with aluminium anodised knob of approved quality all as per drg and complete all as per speciation and directed.

Removal of unserviceable stiffner and S&F new stiffner to accommodate drawer made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s top and S&F new top made out of 18 mm thick MDF Board exterior grade of 18mm thick both side laminated duly covered with teakwood beading 6mm thick half round all around, complete all as specified.

M&L for french polishing of complete table exposed to view except laminated portion complete all as per specified and directed.

REPAIR TO TABLE 900x900x760 MM W/O DRAWER [DRG NO: (FD-88M) ]

Removal of unserviceable leg and S&F new leg made of 1st class hard wood (teak wood) for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s top long rail and S&F new front top long rail made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

S&F extra H type stiffner made out of 1st class hard wood (teak wood) of size 30X30 mm complete all as specified and directed.

Removal of u/s top and S&F new top made out of 18 mm thick MDF Board exterior grade one side laminated duly covered with teakwood beading 6mm thick half round all around, complete all as specified.

M&L for french polishing of complete table exposed to view except laminated portion complete all as per specified and directed.

REPAIR TO CHAIR EASY [DRG NO: (FD-17(M),202 & 229)]

Removing the existing unsv/broken rear leg and supplying and fixing 1st class hard wood rear leg complete all as specified and shown on drags (Each leg measured separately).

Removing the existing unsv/ broken front leg and supplying and fixing 1st class hard wood front leg complete all as specified and shown on drgs (Each leg measured separately).

Removing the existing unsv/ broken arms rest and supplying and fixing 1st class hard wood arms rest complete all as specified and shown on drgs (Each arms rest measured separately).

French polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs.

REPAIR TO CHAIR DINNING [DRG NO: (FD-16,FD-228 & FD- 279)]

Removing the existing unserviceable/Broken rear leg and supplying and fixing 1st class hard wood rear leg complete alla s specified and shown on drgs (Each leg measured separately)

Removing the existing unserviceable/ broken front leg and sjupplying and fixing 1st class hard wood front leg complete all as specified and shown on drgs (Each leg measured spearately).

Removing the existing unserviceable/ broken fillet of canning and supplying and fixing 1st class hard wood fillet for canning including drilling holes at 12.5 mm cc complete all as specified and shown on drgs.

Removal of unserviceable back rest batten and S&F new back rest batten made out of 1st class hard wood of size as per drg complete all as specified and directed.

French polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs).

REPAIR TO CHAIR WOODEN BOTTOM [DRG NO: (FD-56,FD-225 & FD-285) )]

Removing the existing unsv/ broken seat ply and supplying and fixing new seat made out of 6 mm ply wood commercial face veneer of both sides including drilling holes complete all as specified and shown on drgs (Complete seat of one chair measured separately)

French polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs.

COMMON ITEMS FOR CHAIRS [DRG NO: (FD-17,20,250 & 280) (FD-16,228 & FD- 279) (FD-202, 229)]

Removing the existing unsv/ broken plastic cane suplying and canning with new plastic cane 2 mm wide and 4 mm for borders for canning of chair of all types including couch with detachable chair, bin soied linen, stool dressing complete as per Godrej pattern.

Supply & fix stiffeners for chairs made out of 25 X 25 mm 1st class hard wood after removing the existing unserviceable stiffeners complete all as specified and as shown on drgs.

REPAIR TO CHAIR DINNING CUSHIONED [DRG NO: (FD/MAP-11/04)]

Removing the existing worn out seat cushion and S&F new PU foam seat foam of size 450X450X75mm thick, with 12 mm thick plywood BWR grade phenol bonded covered with tapestry cloth for chair dining cushioned complete all as specified and shown on drawing. (Tapestry cloth shall be approved by GE)

Preparation of surfaces and french polishing to wooden surfaces for repaired chairs and applying two or more coat French polish on new surfaces and one coat on old surfaces to match uniform shade complete all as specified and shown on drg.

REPAIR TO TABLE CENTRE/PEG TABLE/TEAPOY [DRG NO: (FD-274, FD-277, 384, FD-382)]

Removing the existing unserviceable top table centre and S&F new top made out of 18 mm thick pre laminated MDF board exterior grade duly edging with 6mm thick beading including French polishing to wooden surface to match the existing surfaces of repaired table centre apply one coat French polish on new surfaces and one coat on old surfaces to match uniform shade complete all as specified and shown on drawing.

All as per item Ser No 18.01 above but top of Peg Table.

All as per item Ser No 18.01 above but top of Teapoy

REPAIRS TO TRESTLE WOODEN [DRG NO: (FD-96M)]

Removing existing unsv legs of trestle store room wooden and S&F new legs made out of second class hard wood of size 300x100x100mm as per drg .

M&L for smoothening surface with sand paper of Trestle wooden and repainting the old painted surface with one coat of synthetic enamel paint black colour complete all as specified and directed.

REPAIRS TO SOFA SET 4/5 SEATER SEAT [DRG NO: (FD-281)]

Replacement of existing foam cushions of Sofa set 04/05 seater including existing tapestry cloth of sofa set 4/5 seater, and supply & fix new PU Moulded Foam 50-55 kg per cubic meter density of size 560 x 535 x 100mm thick, duly stitched with tapestry cloth and closed with valcrow of suitable size complete all as directed and shown on drg . Make: Sleepwell, Kurlon Note: (Tapestry cloth shall not be less than Rs. 350.00 Per RM).

Replacement of tapestry cloth of cushions of sofa set 4/5 seater, seat and back and supply & fix new tapestry cloth size 560 x 535 x 100mm thick on existing foam cushion with valcrow on one edge of best quality. The cost of tapestry cloth to be not less than Rs 350/- per meter.

Removing unsv long rail of front or back side of three seater sofa set and supply and fix new long rail made out of first class Hard Wood of size 1590x100x35mm duly french polished complete all as specified and as shown on drgs.

Removing unsv short rail of any side of sofa set 4/5 seater and supply and fix new short rail made out of first class Hard Wood of size 525x100x35mm duly french polished complete all as specified and as shown on drgs.

Removing unsv wooden bearers of any side of sofa set 4/5 seater and supply and fix new wooden bearers made out of first class Hard Wood of size 525x40x40mm duly french polished complete all as specified and as shown on drgs.

Removing unsv wooden Arms of any side of sofa set 4/5 seater and supply and fix new wooden Arms made out of first class Hard Wood of size 525x40x40mm duly french polished complete all as specified and as shown on drgs.

M&L for smoothening surface with sand paper of Sofa set five seater for repolshing the old polished surface or unpolished surface of sofa with one coat of french polish both above and below the sofa complete all as specified and directed.

M&L for smoothening surface with sand paper of Sofa set four seater for repolshing the old polished surface with one coat of french polish complete all as specified and directed.

PVC MOULDED CUSHIONED CHAIRS WITH ARMS

Removing unsv Seat of chair PVC moulded cushioned and Supply and Fix new Seat 75mm thick polyurethane foam(PU) moulded with density 50-55kg per cubic mtr thick and hardness duly covered with tapesry cloth not less than 250/- per RM all as specified and directed.

Removing unsv back of chair PVC moulded cushioned and Supply and Fix new back 75 mm thick (PU) polyurethane foam moulded with density 50-55kg per cubic mtr thick and hardness duly covered with tapestry cloth not less than 250/- per RM all as per drg and as specified.

VENUS TRADING CORPORATION

LAXMI & GANESH ENTERPRISE

M/S NARAYAN ENTERPRISE