Construction of Multipurpose Hall at Jawahar Navodaya Vidyalaya, Sambalpur, Odisha.

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

3 2.25 not exceeding 20cm in depth,consolidating each 94.76 CUM 196.00 18572.96

deposited layer by ramming and watering, lead upto

50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors,

4 2.27 including watering, ramming,consolidating and 140.00 CUM 2123.75 297325.00

dressing complete.

Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

5 2.25a lead of 5km also including ramming and watering of 1050.00 CUM 700.50 735525.00

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

6 Anti termite treatment

Supplying chemical emulsion in sealed containers

including delivery as specified.

8 2.34.1 Chlorpyriphos emulsifiable concentrate of 20% 294.20 Litre 234.75 69063.45

Diluting and injecting chemical emulsion for POST-

9 2.35 CONSTRUCTIONAL anti-termite treatment (excluding

the cost of chemical emulsion) :

Along external wall where the apron is not provided

using chemical emulsion @ 7.5 litres / sqm of the

vertical surface of the substructure to a depth of

10 2.35.1.1 300mm including excavation channel along the wall 98.03 Metre 38.90 3813.44

& rodding etc. complete: With Chlorpyriphos/

Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart

11 2.35.3 including drilling 12 mm diameter holes and plugging

with cement mortar 1 :2 (1 cement : 2 Coarse sand)

to match the existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1%

13 Concrete Work

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level 1:4:8 (1

14 4.1.8 Cement : 4 coarse sand (zone-III) derived from 122.40 CUM 6518.60 797876.64

natural sources : 8 graded stone aggregate 40 mm

nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse

15 4.10 sand (zone-III) derived from natural sources : 4 61.23 SQM 410.85 25156.35

graded stone aggregate 12.5mm nominal size

derived from natural sources)

Extra for providing and mixing water proofing

material in cement concrete work in doses by weight per 50kg

of cement as per manufacturer's specification. cement

Providing & applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using

17 4.13 1.7kg per square metre on damp proof course after 61.23 SQM 146.15 8948.76

cleaning the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural

18 4.17 sources) over 75mm thick bed of dry brick ballast 40 127.94 SQM 749.30 95865.44

mm nominal size, well rammed and consolidated and

grouted with fine sand,including necessary

excavation,levelling & dressing & finishing the top

Brick edging in full brick width and half brick depth

including excavation, refilling and disposal of surplus

19 16.7.1 earth lead upto 50 metres. 170.58 RM 194.30 33143.69

With common burnt clay F.P.S. (non modular) bricks

of class designation 7.5

20 Reinforced Cement Concrete

Centering and shuttering including strutting,

21 propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for

23 5.9.3 Suspended floors, roofs, landings, balconies and 739.86 SQM 927.25 686035.19

access platform.

24 5.9.5 Lintels, beams, plinth beams, girders, bressumers 1289.50 RM 736.40 949590.01

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

25 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts. 676.08 SQM 961.30 649914.74

Small lintels not exceeding 1.5 m clear span,

26 5.9.15 moulding as in cornices, window sills, string courses, 247.69 SQM 307.95 76276.14

bands, copings, bed plates, anchor blocks and the

Extra for additional height in centering, shuttering

where ever required with adequate bracing, propping

etc., including cost of de-shuttering and decentering

27 5.11.1 at all levels, over a height of 3.5 m, for every 515.16 SQM 384.30 197975.99

additional height of 1 metre or part thereof (Plan

area to be measured).

Suspended floors, roofs, landing, beams and

balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

28 5.22.6 and binding all complete upto plinth level. Thermo- 15000.00 KG 107.85 1617750.00

Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

29 5.22.A.6 and binding all complete above plinth level. 23860.90 KG 107.85 2573398.07

Thermo-Mechanically Treated bars of grade Fe-500 D

Add for plaster drip course/ groove in plastered

surface or moulding to R.C.C. projections.

Providing and laying in position specified grade of

reinforced cement

30 5.10 concrete, excluding the cost of centering, shuttering,

reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III)

(I) 5.1.2 derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from natural

(i) R.C.C. work in Footing 86.78 CUM 9045.75 784990.19

(ii) R.C.C. work in Beam 40.71 CUM 9045.75 368252.48

Reinforced cement concrete work in beams,

suspended floors, roofs having slope up to 15°

landings, balconies, shelves, chajjas, lintels,

bands, plain window sills, staircases and spiral stair

5.3 cases above plinth level up to floor five level,

excluding the cost of centering, shuttering,

finishing and reinforcement with 1:1.5:3 (1 cement :

1.5 coarse sand(zone-III) derived from natural

sources : 3 graded stone aggregate 20 mm nominal

size derived from natural sources). 19.71 CUM 11505.50 226773.41

(iii) R.C.C. work in Columns

Concrete of M25 grade with minimum cement

content of 330 kg /cum

(i) R.C.C. work in Lintel 5.26 CUM 11505.50 60518.93

(ii) R.C.C. work in Beam 87.04 CUM 11505.50 1001381.19

(iv) R.C.C. work in Slab 120.99 CUM 11505.50 1392050.45

D Masonry Work

Half brick masonry with common burnt clay F.P.S.

(non modular) bricks of class designation 7.5 in

31 6.13.2 superstructure above plinth level up to floor V 171.57 Sqm 1123.80 192810.37

level.Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos

32 6.15 6mm dia. M.S. bars at every third course of half brick 171.57 SQM 104.80 17980.54

Brick work with non modular fly ash bricks

conforming to IS:12894, class designation 10

33 6.34.2 average compressive strength in superstructure 290.62 CUM 8752.55 2543666.08

above plinth level up to floor V level in : Cement

mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non

modular) bricks of class

34 6.1.2 designation 7.5 in foundation and plinth in: 94.88 CUM 7132.25 676707.88

Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in

foundation and plinth including levelling up with

35 7.1 cement concrete 1:6:12 (1 cement : 6 coarse sand :

12 graded stone aggregate 20 mm nominal size)

upto plinth level with :

7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 14.70 CUM 7311.25 107475.38

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required

size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at all

Providing edge moulding to 18mm thick marble stone

counters, Vanities etc. including machine polishing to

37 edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone over and above

38 8.4 corresponding basic item, in facia and drops of width 79.50 RM 568.55 45199.73

upto 150 mm with epoxy resin based adhesive

including cleaning etc. complete.

Extra for providing opening of required size & shape

for wash basins/ kitchen sink in kitchen platform,

39 8.5 vanity counters and similar location in 8.00 EACH 978.70 7829.60

marble/Granite/stone work including necessary holes

for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge,

40 8.31 in skirting, risers of steps and dados, over 12 mm 268.67 SQM 1267.95 340660.13

thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

(Size-300x450 )

Providing and Fixing of Acoustical Wall Panel with

square edges made of fibre glass substrate 25mm

thick, wrapped on the front side with an acoustically

transparent fabric as per the approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal,

Titanium, Flame, Peanut and Shell). The panel shall

be classified for Fire Class A, as per ASTM E-84. The

Acoustical Wall Panel shall be of sizes 600x600mm

(Nominal) or 600x1200mm (Nominal) and shall

achieve an NRC of 0.85 (Average value of Absorption

Co-efficient readings taken at 250 Hz, 500 Hz, 1000

Hz and 2000 Hz) with 50mm airgap as per ASTM

C423 to be fixed to wall on a framework of wooden

41 MR battens and using Wall panel Impalers (supplied by 95.00 sqm 13560.67 1288263.65

the manufacturer) or by using construction adhesives

(as per the instructions laid down by the

manufacturer). The fibre glass substrate shall have a

recycle content of 85%. Properties of Tile Relevant

Standards Base Material Fibre Glass

Panel Dimensions 600mm x 600/1200mm Panel

Panel Finish Acoustically transparent fabric as per the

approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal,

Titanium, Flame, Peanut and Shell).

Fire Properties Class A ASTM E-84

Noise Reduction Co-efficient 0.85 ASTM C423

(Average value of Absorption Coefficient

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Providing & fixing of 100% Natural Material-

Magnesite (Hygroscopic & biologically sound binding

agent) bonded woodwool Panel planks of

600Mm*1200Mm *25Mm thickness made out of

wood wool fibre of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with

open & smooth surface texture. A Completly

harmless Envirenment & Human Friendly & also a

disposable or recyclable Material & can last for long

span in building interiors As it has long lifespan &

suitable for Indoor conditions with relative air

42 MR humidity of upto 90%. Magnesite protects the wood 95.00 sqm 13085.71 1243142.45

cells against ageing & fungal attack. To achive upto

NRC=1.00 it should be a clear gap of 200Mm from

wall slab along with the backing of Mineral of

50kg/m3. Edge Detail : AK 01

Heradesign Woodwool - Acoustical Wall Mounting

System Solutions- Ecologically Sound

Material with high mechanical strength with Crash

test of 90Km/H with Ball Impact Test

DIN18032 & EN13964 with flying colors & A

sustainable material (PEFC & FSC Certified)

along with EPD Certified Acc. to EN ISO 14025 (AUB-

Environmental Product declaration).

G Wood and PVC Work

Providing and fixing panelling or panelling and

glazing in panelled or

panelled and glazed shutters for doors, windows and

43 9.7 clerestory windows (Area of opening for panel inserts

excluding portion inside grooves or rebates to be

measured). Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

9.7.7 Float glass panes

5.0 mm thick glass panes (weight not less than

Providing and fixing Fiber Glass Reinforced plastic

(FRP) Door Frames of cross-section 90 mm x 45 mm

having single rebate of 32 mm x 15 mm to receive

shutter of 30 mm thickness. The laminate shall be

moulded with fire resistant grade unsaturated

44 9.121 polyester resin and chopped mat. Door frame 76.05 RM 570.95 43420.75

laminate shall be 2mm thick and shall be filled with

suitable wooden block in all the three legs. The frame

shall be covered with fiber glass from all sides. M.S.

stay shall be provided at the bottom to steady

30 mm thick Fiberglass Reinforced Plastic (F.R.P.)

flush door shutter in different plain and wood finish

made with fire retardant grade unsaturated polyester

resin, moulded to 3 mm thick FRP laminate all

around, with suitable wooden blocks inside at

45 9.122.2 required places for fixing of fittings and polyurethane 24.86 SQM 4488.95 111595.30

foam (PUF)/Polystyrene foam to be used as

filler material throughout the hollow panel, casted

monolithically with testing parameters of F.R.P.

laminate conforming to table - 3 of IS: 14856,

complete as per direction of Engineer-in-charge.

Providing and fixing factory made uPVC white colour

casement/ Casement cum fixed glazed door comprising of

uPVC multi-chambered frame, sash and mullion (where

ever required) extruded profiles duly reinforced with 1.60

± 0.2 mm thick galvanized mild steel section made from

roll forming process of required length (shape & size

according to uPVC profile), uPVC extruded glazing beads of

appropriate dimension, EPDM

gasket, zinc alloy (white powder coated) 3D hinges and

one handle on each side of panels along with zinc plated

mild steel multi point lockinghaving transmission gear,

cylinder with keeps and one side key, G.I fasteners 100 x

8 mm size for fixing frame to finished wall and necessary

46 9.147C stainless steel screws, etc. Profile of frame & sash shall be

mitred cut and fusion welded at all corners, mullion (if

required) shall be also fusion welded including drilling of

holes for fixing hardware's and drainage of

water etc. After fixing frame the gap between frame and

adjacent finished wall shall be filled with weather proof

silicon sealent over backer rod of required size and of

approved quality, all complete as per approved drawing &

direction of Engineer-in-Charge. (Single / double glass

panes and silicon sealent shall be paid separately).

Variation in profile dimension

in higher side shall be accepted but no extra payment on

this account shall be made.

Note: For uPVC frame, sash and mullion extruded profiles

minus 5% tolerance in dimension i.e. in depth & width of

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Casement door with top hung ventilator with 3D and

friction hinges (400 x 19 x 1.9 mm) made of (big

frame 67 x 64 mm, sash 67 x 110 mm & mullion 67

mm all having wall thickness of 2.3 ±. 0.2 mm and

single glazing bead / double glazing bead of

dimension.(Area of door upto 2.50 sqm)

Providing and fixing fire resistant door frame of

section 50 x 60 mm on horizontal side & 35 x 60 mm

on vertical sides having built in rebate made out of

1.6 mm thick GI sheet ( Zinc coating not less than

120gm/m²) suitable for mounting 120 min Fire Rated

Glazed Door Shutters. The frame shall be filled with

Mineral wool Insulation having density min 96Kg/m³

. The frame will have a provision of G.I. Anchor

fastners 14 nos ( 5 each on vertical style & 4 on

horizontal style of size M10 x 80 ) suitable for fixing

in the opening along with Factory made Template for

SS Ball Bearing Hinges of Size 100x89x3mm for

fixing of fire rated glazed shutter . The frame shall be

finished with a approved fire resistant primer or

Powder coating of not less than 30 micron in desired

shade as per the directions of Engineer - in- charge .

(Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant

door shutters of 120 min Fire Rating confirming to

IS:3614 (Part II) or EN1634-1:1999,

tested and certified as per laboratory approved by

Engineer-in-charge, with suitable mounting on door

frame, consisting of vertical styles, top rail & side rail

60 mm x 60 mm wide and bottom rail of 110 mm x

60mm made out of 1.6mm thick G.I. sheet (zinc

48 9.162 coating not less than120gm/m²) duly filled mineral 25.60 SQM 12070.90 309015.04

wool insulation having density min 96 kg/m³ and

fixing with necessary stainless steel ball bearing

hinges of size100x89x3mm of approved make,

including applying a coat of approved fire resistant

primer or powder coating not less than 30 micron etc

all complete as per direction of Engineer-in-charge

(panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door

shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc

coating not less than 120 gm/m²) of size 20 x 33

mm screwed with M4 x 38 mm SS screws at distance

75 mm from the edges and150 mm c/c , including

applying a coat of approved fire resistant

primer/powder coating of not less than 30 micron on

G.I. beading, & special ceramic tape of 5 x 20 mm

size etc complete in all respect as per NBC 2016, IS

16231 (Part 3):2016 and as per direction of

Engineer-incharge with glass of required thickness

49 9.164 having 120 minutes of fire resistance both integrity & 2.16 SQM 43677.65 94343.72

radiation control (EW120) and minimum 20minutes

of insulation (EI20). The manufacturer have to give

test report/certification of fire glass and the glass

should have the stamp showing the value of E, EW &

EI. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body

which operates in accordance with ISO/IEC 17011

and accredits labs as per ISO/IEC 17025 for testing

and calibration scopes shall be eligible. The

maximum glazing size shall not be

more than 1100x2200 mm (w x h) or 2.42 sqm.

Note: Rate of hardware items deemed to be include

in above items. All Hardware required as per

approved shop drawing should pass European

certificate "CE" of conformity / UL with required fire

Providing and fixing bright /matt finished Stainless

50 9.165.1 Steel handles of approved quality & make with 26.00 NOS 119.20 3099.20

necessary screws etc all complete. (a) 125 mm.

Providing & fixing Stainless steel (grade SS-304 or

51 M.R. higher) sliding door bolt/aldrop of size 250x16mm on 13.00 NOS 719.00 9347.00

door shutter including all accessories as per direction

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Providing and fixing Stainless steel (grade SS-304 or

52 higher) tower bolt (barrel type) with necessary

screws etc. complete all work as per direction of E/I

Filling the gap in between aluminium frame &

adjacent RCC/ Brick/ Stone work by providing

53 21.8.1 weather silicon sealant over backer rod of approved 351.40 RM 96.75 33997.95

quality as per architectural drawings and direction of

Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Steel work in built up tubular (round, square or

rectangular hollow tubes

etc.) trusses etc., including cutting, hoisting, fixing in

54 10.16.1 applying a priming coat of approved steel primer, 3000.00 KG 194.40 583200.00

including welding and

bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Designing, Providing, installing and fixing factory

finished customed

design pregalvanized high tensile steel joists

manufactured from G350 Z275 confirming to IS:277-

55 26.62 1992, minimum coating of galvanizing 275 gm/sqm, 200.00 KG 182.05 36410.00

minimum yield stress 35 MPa & minimum tensile

strength of 380 MPa placed 1.23 metre apart to

support the load of slab etc as per the design &

directions of Engineer-in-Charge.

Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

56 10.25.2 using structural steel etc. as required. In gratings, 980.00 KG 172.60 169148.00

frames, guard bar, ladder, railings, brackets,

gates and similar works

Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts

57 10.28 complete, i/c fixing the railing with necessary 1300.00 KG 772.40 1004120.00

accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top

of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge.

Structural steel work riveted, bolted or welded in

built up sections, trusses and framed work, including

58 10.2 cutting, hoisting, fixing in position and applying a 500.00 KG 133.70 66850.00

priming coat of approved steel primer all complete.

Designing, providing, installing and fixing factory

finished custom

designed cold form Light Gauge Steel Framed super

comprising of steel wall panel, trusses, purlins etc

manufactured out of minimum 0.75 mm thick steel

sheet as per design requirements. The steel sheet

shall be galvanized (AZ-150gms Aluminium Zinc

Alloy coated steel having minimum yield strength

300-550 Mpa) conforming to AISI specifications and

IBC 2009 for cold formed steel framing and

construction and also as per IS: 875-1987, ISO 800-

1984 and IS:01-1975. The wind load shall be as per

#REF! 26.41 provisions of IS 875 (part -III). 1300.00 KG 285.90 371670.00

LGSFS frame shall be designed as per IS: 801 using

commercially available software such as Frame CAD

Pro-11.7/ STAAD PRO-V8i/ ArchitekV2.5.16/ Revit

architecture-2011 or equivalent. Proper usage

of Connection Accessories like Heavy Duty Tension

Ties, Light Duty Hold-ons, Twist Straps (to connect

truss with wall frames), Strong Tie, Tie Rod, H-

Brackets, Boxing Sections, L-Shaped Angles for

better structural stability. The framing section shall

be cold form C-type having minimum web depth 89

mm x 39mm flange x 11mm lip in required

length as per structural design requirement duly

punched with dimple/ slot at required locations as

per approved drawings. The slots will be along centre

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Chequerred precast cement concrete tiles 22 mm

thick in footpath & courtyard, jointed with neat

cement slurry mixed with pigment to match the

#REF! 11.20.2 shade of tiles, including rubbing and cleaning etc. 96.05 SQM 1328.35 127588.02

complete, on 20 mm thick bed of cement mortar 1:4

(1 cement: 4 coarse sand). Medium shade pigment

using 50% white cement 50%

Marble stone flooring with 18 mm thick marble stone,

of marble approved by Engineer-in-charge, over 20

11.23 mm (average) thick base of cement mortar 1:4 (1

cement : 4 coarse sand) laid and jointed with grey

cement slurry, including rubbing and polishing

complete with :

#REF! 11.23.2 Raj Nagar plain 21.75 SQM 2346.80 51042.90

52 mm thick cement concrete flooring with concrete

hardener topping, under layer 40 mm thick cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size) and top layer

12 mm thick cement hardener consisting of mix 1:2

#REF! 11.4 (1 cement hardener mix : 2 graded stone aggregate 681.25 SQM 978.45 666569.06

6 mm nominal size) by volume, hardening compound

mixed @ 2 litre per 50 kg of cement or as per

manufacturer's specifications. This includes cost of

cement slurry, but excluding the cost of nosing of

steps etc. complete.

Cement plaster skirting up to 30 cm height, with

#REF! 11.6 cement mortar 1:3

(1 cement : 3 coarse sand), finished with a floating

coat of neat cement.

Providing and laying rectified Glazed Ceramic floor

tiles of size 300x300

mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in all colours, shades,

#REF! 11.40 except White, Ivory, Grey, Fume Red Brown, laid on 81.08 SQM 1439.40 116706.55

20 mm thick Cement Mortar 1:4 (1 Cement : 4

Coarse sand), jointing with grey cement slurry @ 3.3

kg/ sqm including pointing the joints with white

cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all

#REF! 11.41.2 colours and shades, laid on 20mm thick cement 91.22 SQM 1553.45 141705.71

mortar 1:4 (1 cement : 4 coarse sand), jointing with

grey cement slurry @ 3.3kg/sqm including grouting

the joints with white cement and matching pigments

etc., complete. (a) Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and

conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid

on 20 mm thick cement mortar 1:4 (1 cement: 4

coarse sand) jointing with grey cement slurry @3.3

#REF! 11.41A kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must

be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently

11.41A.1 Double charge vitrified tile polished finish of size

Providing and laying Vitrified tiles in different sizes

(thickness to be specified by manufacturer), with

water absorption less than 0.08 % and onforming to

I.S. 15622, of approved make, in all colours & shade,

#REF! 11.46.2 in skirting, riser of steps, over 12 mm thick bed of 13.29 SQM 1623.05 21570.33

cement mortar 1:3 (1 cement: 3 coarse sand),

jointing with grey cement slurry @ 3.3kg/sqm

including grouting the joint with white cement &

matching pigments etc. complete. Size of Tile

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Providing and laying flamed finish Granite stone

flooring in required design and patterns, in linear as

well as curvilinear portions of the building all

complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4coarse

#REF! 11.55.1 sand) laid and jointed with cement slurry and 40.39 SQM 3186.70 128710.81

pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing

and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :Flamed finish

granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring

in required design and patterns, in linear as well as

curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of

cement mortar 1:4 (1 cement : 4 coarse sand) laid

#REF! 11.56.1 and jointed with cement slurry and pointing with 60.07 SQM 4481.30 269191.69

white cement slurry admixed with pigment of

matching shade including rubbing, curing and

polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black,

Cherry/Ruby Red or equivalent

Providing and laying C.C. pavement of mix M-25 with

ready mixed concrete from batching plant. The ready

mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and

finally finished by floating, brooming with wire brush

etc. complete as per specifications and directions of

#REF! 16.75 Engineer-incharge. 30.17 CUM 9823.80 296384.05

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this item is @

Excess/less cement used as per design mix is

payable/ recoverable separately).

Providing and fixing false ceiling at all height

including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia

#REF! bolts, other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm

centre to centre, to which the ceiling section 0.5 mm

thick bottom wedge of 80 mm with tapered flanges

of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel

with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of

ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x

25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges

of the board with recommended jointing

compound , jointing tapes , finishing with jointing

layers covering upto 150 mm on both sides of joint

and two coats of

primer suitable for board, all as per manufacturer's

specification and

also including the cost of making openings for light

fittings, grills,

diffusers, cutouts made with frame of perimeter

channels suitably

fixed, all complete as per drawings, specification and

the Engineer in Charge but excluding the cost of

painting with :

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

12.5 mm thick tapered edge gypsum plain board

12.45.1 conforming to IS: 2095- (Part I) :2011 (Board with 275.62 SQM 1355.80 373691.02

BIS certification marks)

Providing and fixing tiled false ceiling of specified

materials of size 595x595 mm in true horizontal

level, suspended on inter locking metal grid of hot

dipped galvanized steel sections ( galvanized @

120 grams/ sqm, both side inclusive) consisting of

main "T" runner with suitably spaced joints to get

required length and of size 24x38 mm made from

0.30 mm thick (minimum) sheet, spaced at 1200

mm center to center and cross "T" of size 24x25 mm

made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to

center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size

#REF! 24x25 mm made of 0.30 mm thick (minimum) sheet

to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of

approved texture in the grid including, required

cutting/making, opening for services like diffusers,

grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using

GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed

to ceiling with 12.5 mm dia and 50 mm long dash

fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced

at 1200 mm center to center along main T, bottom

exposed width of 24 mm of all T-sections shall be

Metal Ceiling polyester

in plainpaint, all complete

white color tiles of size 595x595 mm, and 0.5 mm

thick with 8 mm drop; made of G I sheet having

12.52.1 galvanizing of 100 gms/sqm (both sides inclusive) 65.58 SQM 1902.95 124795.46

and electro statically polyester powder coated of

thickness 60 microns

(minimum), including factory painted after bending.

12mm cement plaster in single coat on fair side of

single or half brick wall for exterior plastering up to

floor two level including internal rounded angles

#REF! 13.4.2 chamfers, and/or rounded angles not exceeding 1189.66 SQM 343.65 408826.66

80mm in girth and finished even and smooth no

extra for mixing any additive. 1:6 (1 cement: 6

15 mm cement plaster on the rough side of single or

#REF! 13.5.2 half brick wall of mix : 1:6 (1 cement: 6 coarse 2367.85 SQM 395.35 936129.50

6 mm cement plaster on celling (a) 1:3(1 cement:3

Finishing walls with textured exterior paint of

required shade: New work (Two or more coats

#REF! 13.45.1 applied @ 3.28 ltr/10 sqm) over and including 1189.66 SQM 223.60 266007.98

priming coat of exterior primer applied @ 2.20kg/10

Finishing walls with 100% Premium acrylic emulsion

paint having VOC less than 50 gm/litre and UV

#REF! 13.48A resistance as per IS 15489:2004, Alkali & fungal

resistance, dirt resistance exterior paint of required

shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/

13.48A.1 10 sqm. Over and including priming coat of exterior 1705.91 SQM 181.25 309196.82

primer applied @ 0.90 litre/10 sqm.

13.50 Applying priming coat:

With ready mixed red oxide zink chromate primer of

#REF! 13.50.3 approved brand and manufacture on steel galvanised 905.99 SQM 67.40 61063.73

iron/steel works.

Painting with synthetic enamel paint of approved

#REF! 13.61 brand and manufacture to give an even shade:

13.61.1 Two or more coats on new work. 905.99 SQM 155.90 141243.84

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

#REF! 13.80 manufacturer, over the plastered wall surface to 1663.33 SQM 156.05 259562.65

prepare the surface even and smooth complete.

L ALUMINIUM WORK

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Providing and fixing aluminium work for doors,

windows, ventilators

and partitions with extruded built up standard tubular

appropriate Z sections and other sections of

conforming to IS: 733 and IS: 1285, fixing with dash

required dia and size, including necessary filling up

#REF! 21.1 junctions, i.e. at top, bottom and sides with required

neoprene gasket etc. Aluminium sections shall be

smooth, rust free,

straight, mitred and jointed mechanically wherever

required including

cleat angle, Aluminium snap beading for glazing /

brass / stainless steel screws, all complete as per

drawings and the directions of Engineer-in-charge.

(Glazing, paneling

21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed

21.1.1.1 to required shade according to IS: 1868, Minimum 277.44 KG 495.05 137346.67

anodic coating of grade

For shutters of doors, windows & ventilators

providing and fixing hinges/ pivots and making

21.1.2 for fixing of fittings wherever required including the

of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately)

Anodised aluminium (anodised transparent or dyed

21.1.2.1 to required shade according to IS: 1868, Minimum 647.36 KG 598.60 387509.70

anodic coating of grade

Providing and fixing glazing in aluminium door,

window, ventilator

shutters and partitions etc. with EPDM rubber /

neoprene gasket

#REF! 21.3 etc. complete as per the architectural drawings and

the directions of

engineer-in-charge . (Cost of aluminium snap

beading shall be paid

in basic item):

With float glass panes of 8 mm thickness (weight not

M Water Proofing

Providing and laying in situ seven course water

proofing treatment with APP (Atactic poly-propylene)

modified Polymeric memberane over roof consisting

of first coat of bitumen primer @ 0.40 litre per sqm,

2nd, 4th & 6th courses of bonding material @ 1.20

Kg/sqm, which shall consist of blown type bitumen of

grade 85/25 conforming to IS : 702, 3rd and 5th

layers of roofing membrane APP modified Polymeric

membrane 1.5 mm thick of 2.25 Kg/sqm weight

consisting of five layers prefabricated with centre

#REF! 14.86 core as 20 micron HMHDPE film sandwiched on both 58.67 SQM 730.55 42861.37

sides with polymeric mix and the polymeric

mix is protected on both side with 20 micron

HMHDPE film. 7th, the top most layer shall be

finished with brick tiles of class designation

10 grouted with cement mortar 1:3 (1cement : 3 fine

sand) mixed with 2% integral water proofing

compound by weight of cement over

a 12 mm layer of cement mortar 1:3 (1 cement : 3

fine sand) and finished neat (item of laying brick tiles

shall be paid for separately).

Providing and laying brick tiles over mumty roofs,

grouted with cement

mortar 1:3 (1 cement : 3 fine sand) mixed with 2%

#REF! of integral water

proofing compound by weight of cement, over 12

mm layer of cement

mortar 1:3 (1 cement : 3 fine sand) and finished

With common burnt clay F.P.S. (non modular) brick

of class designation 10

N Roof Sheeting

PROFLEX Roof System wuth 1.3 mm thick color

coated galvanised sheet

O Loft and Wardrobes

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

All works above plinth level upto floor V level

#REF! 5.9.3 Suspended floors, roofs, landings, balconies and 8.40 Sqm 927.25 7788.90

access platform.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

#REF! 5.22.A.6 and binding all complete above plinth level. Thermo- 63.00 Kg 107.85 6794.55

Mechanically Treated bars of grade Fe-500 D or

12mm cement plaster in single coat on fair side of

single or half brick wall for exterior plastering up to

floor two level including internal rounded angles

#REF! 13.4.2 chamfers, and/or rounded angles not exceeding 9.45 Sqm 343.65 3247.49

80mm in girth and finished even and smooth no

extra for mixing any additive. 1:6 (1 cement: 6

6 mm cement plaster on celling (a) 1:3 (1 cement:3

Wall painting with acrylic emulsion paint of approved

#REF! 13.60 brand and manufacture to give an even shade :

#REF! 13.60.1 Two or more coats on new work. 17.85 Sqm

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

#REF! 13.80 manufacturer, over the plastered wall surface to 17.85 Sqm 156.05 2785.49

prepare the surface even and smooth complete.

Providing wood work in frames of false ceiling,

#REF! 9.3 partitions etc. sawn and fixed in position with

necessary stainless steel screws etc.

Kiln seasoned and chemically treated hollock wood

Providing and fixing cup board shutters 25 mm thick,

with Pre-laminated flat pressed three layer particle

board or graded wood particle board IS: 12823

marked, exterior grade (Grade l Type ll), having one

#REF! 9.129 side decorative lamination and other side balancing 36.73 Sqm 2307.35 84742.04

lamination, including IInd class teak wood lipping of

25 mm wide x12 mm thick with necessary screws

and bright finished stainless steel piano hinges,

complete as per direction of the Engineer-in-Charge

Providing and fixing Pre-laminated medium density

fibre board IS: 14587:1998 marked, with one side

decorative lamination other side balancing lamination

9.157 Grade-I (exterior grade) in shelves with screws and

fittings wherever required, edges to be sealed with

PVC edge bending tape 2.00 mm thick of approved

brand (fittings to be paid separately).

Pre-laminated with decorative lamination one side

#REF! 9.157.1 and other side balancing lamination exterior Grade - 30.71 Sqm 1415.70 43481.81

I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing magnetic catcher of approved

#REF! 9.114 quality in cupboard / ward robe shutters, including

fixing with necessary screws etc. complete.

9.114.2 Double strip (horizontal type) 26.00 Each 39.70 1032.20

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills, facias and similar locations of required

size, approved shade, colour and texture laid over 20

8.2 mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at all

#REF! 8.2.2 Granite of any colour and shade

8.2.2.2 Area of slab over 0.50 sqm 9.59 Sqm 5136.30 49277.66

Providing & Fixing decorative high pressure

laminated sheet of plain / wood grain in gloss / matt/

suede finish with high density protective surface

#REF! 9.127.1 layer and reverse side of adhesive bonding quality 27.96 Sqm 1045.95 29240.58

conforming to IS : 2046 Type S, including cost of

adhesive of approved quality 1 mm thick

Providing and fixing wooden moulded beading to

#REF! door and window frames with iron screws, plugs and

priming coat on unexposed surface etc. complete :

Kiln seasoned and chemically treated hollock wood

Providing and fixing special quality chromium plated

#REF! 9.90.2 brass cupboard locks with six levers of approved 13.00 Each 333.95 4341.35

quality including necessary screws etc. complete.

Providing and fixing chromium plated brass handles

#REF! 9.92.2 with necessary screws etc. complete: 100mm 26.00 Each 206.25 5362.50

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Badminton court line marking by acrylic paint of

#REF! MR approved make and as per direction of Engineer- 1.00 Job 69899.00 69899.00

Incharge (tentative area of hall 625 Sqm for 2

badmintan court)

DSR -17.2.1 Providing and Fixing white viterous china pedestal

type water closet ( European type WC Pan ) with

seat and lid , 10 litre low level White pvc flushing

cistern , including flush pipe with manually controlled

1 device ( handle lever ) , Conforming to IS : 7231 10.00 Each 6515.55 65155.50

with all fittings and fixtures complete including

cutting and making good the walls and floors

wherever required . WC Pan with ISI marked white

solid plastic seat and lid .

DSR -17.7 Providing and fixing wash basin with C.I. brackets,

15 mm C.P. brass pillar taps, 32 mm C.P. brass

2 waste of standard pattern, including painting of

fittings and brackets, cutting and making good the

walls wherever require :

White Vitreous China Wash basin size 630x450 mm 9.00 Each 2648.85 23839.65

17.7.1 with a pair of 15 mm C.P. brass pillar tap

DSR -17.31 Providing and fixing 600x450 mm beveled edge

mirror of superior glass ( of approved quality )

3 complete with 6 mm thick hard board ground fixed to 9.00 Each 1607.95 14471.55

wooden cleats with C.P brass screws and washers

17.5 Providing and fixing white vitreous china flat back

half stall urinal of size 580x380x350 mm with white

PVC automatic flushing cistern, with fittings, standard

size C.P. brass flush pipe, spreaders with unions and

clamps (all in C.P. brass) with waste fitting as per IS

: 2556, C.I. trap with outlet grating and other

couplings in C.P. brass, including painting of fittings

and cutting and making good the walls and floors

wherever required :

17.5.3 Range of three half stall urinals with 10 litre P.V.C.

automatic flushing cistern

DSR -8.10 Providing and fixing stone slab with table rubbed,

edges rounded and polished, of size 75x50 cm deep

and 1.8 cm thick, fixed in urinal partitions by cutting

a chase of appropriate width with chase cutter and

4 embedding the stone in the chase with epoxy grout

or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size)

as per direction of Engineer-in-charge and finished

4.1 8.10.2 Granite Stone of approved shade 3.00 Sqm 4051.85 12155.55

5 DSR -18.49 Providing & fixing C.P. brass bib cock of approved

quality conforming to IS :8931.

17.22A Providing and fixing CP Brass 32mm size bottle trap

of approved quality & make and as per the direction 8.00 Each 1034.80 8278.40

of engineer in charge.

DSR -18.53 Providing and fixing C.P. brass angle valve for basin

6 mixer and geyser points of approved quality

conforming to IS:8931

DSR -18.21 Providing and fixing unplasticised P.V.C. connection

7 pipe with PTMT Nuts, collar and bush of approved

quality and colour.

7.1 18.21.2.1 15 mm nominal bore with 45cm length 30.00 Each 97.75 2932.50

DSR -18.53A Providing and fixing CP Brass extension nipple ( size

8 15mm x 50 mm ) of approved make and quality as 30.00 Each 74.80 2244.00

per direction of engineer - in - charge .

DSR -17.28 Providing & fixing of Waste pipe for Wash basins &

Sinks including pvc waste fittings complete.

DSR -18.48 Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, ISI : 12701

10 marked, with cover and suitable locking arrangement 8000.00 Per Litre 11.00 88000.00

and making necessary holes for inlet, outlet and

overflow pipes but without fittings and the base

support for tank.

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

11 DSR -18.58 Providing and fixing PTMT grating of approved quality

Providing and fixing 8mm dia C.P./S.S. Jet with

flexible tube upto 1meter long with S.S. Triangular

plate to european type W.C. Of approved quality and 10.00 Each 349.15 3491.50

make as approved by engineer in charge.

NS-3 Providing and fixing vertical or horizontal storage

type hot water heater electrical operated fixed to wall

with anchor bolts & nuts, 15mm CP brass angle stop

1.00 cock and 15mm CP brass non-return valve complete

including making connections with 15mm dia CP

connecting pipes on inlet and outlet, suitable length

of power cable and 15 amps plug .

13.1 a) 15 Litre Capacity 4.00 Each 12081.00 48324.00

17.22B Providing and fixing CP Brass Single lever telephonic

quality & make as approved by Engineer in charge. 6.00 Each 6940.75 41644.50

(a) 15 mm nominal dia

17.34 Providing and fixing toilet paper holder :

17.71 Providing and fixing PTMT liquid soap container 109

mm wide, 125 mm high and 112 mm distance from

wall of standard shape with bracket of the same

materials with snap fittings of approved quality and 6.00 Each 168.35 1010.10

colour, weighing not less than 105 gms.

17.73 Providing and fixing PTMT towel rail complete with

brackets fixed to wooden cleats with CP brass screws

with concealed fittings arrangement of approved

quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm,

78 mm wide and effective height of 88 mm, weighing 6.00 Each 673.40 4040.40

not less than 170 gms

18.22 Providing and fixing C.P. brass shower rose with 15

18.52 Providing and fixing CP brass stop cock (concealed)

of standard design and approved make confirming

18.52.1 15mm nominal bore 12.00 Each 670.45 8045.40

NS Providing & Fixing of Grab bar size 600X600 mm

pipe O.D 32 mm , thiickness 2 mm of non slipping

grip as per standard specification of use in disabled 1.00 Each 15642.00 15642.00

toilet complete with brackets suitable for wall

installation as per approved sample complete in all

SUB HEAD-II- SOIL , WASTE VENT AND RAIN

DSR -12.22 Making khurras 45x45 cm with average minimum

thickness of 5 cm cement concrete 1:2:4 (1

cement:2 coarse sand:4 graded stone aggregate of

1 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 4.00 Each 298.25 1193.00

micron, finished 12 mm cement plaster 1:3 (1

cement:3 coarse sand) and a coat of neat cement

rounding the edges and making and finishing the

outlet complete

DSR -12.41 Providing and Fixing on wall unplasticised Rigid PVC

Rain water pipes conforming to IS : 13592 Type A ,

2 including jointing with seal ring conforming to IS :

5382 , leaving 10 mm gap for thermal expansion

2.1 12.41.2 Single Socketed pipes 110 mm diameter 96.00 Metre 377.40 36230.40

DSR -12.44 Providing and Fixing to the inlet mouth of rain water

3 pipe cast iron grating 15 cm diameter and weighing 8.00 Each 54.70 437.60

not less than 440 grams .

DSR -12.37 Providing and Fixing 100 mm diameter and 60 cm

4 long rain water spout in cement mortar 1:4 ( 1

Cement : 4 Fine Sand )

4.1 12.37.1 Stone Ware Spout 2.00 Each 164.20 328.40

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

DSR -12.42 Providing and Fixing on wall face Rigid Unplasticised

UPVC moulded fittings / accessories for unplasticised

5 Rigid PVC Rain water pipes conforming to IS : 13592

Type A including jointing with seal ring conforming to

IS : 5382 leaving 10 mm gap for thermal expansion .

12.42.1 Coupler

12.42.2 Single Push Fit Coupler

12.42.3 Single Tee with door

12.42.4 Single Tee without door

12.42.5 Bend 87.5 degree

12.42.6 Shoe ( Plain )

DSR -12.43 Providing and Fixing unplasticised PVC pipe clips of

approved design to unplasticised - PVC rain water

pipes by means of 50x50x50 mm hard wood plugs ,

6 screwed with MS screws of required length ,

including cutting brick work with fixing in cement

mortar 1:4 ( 1 Cement : 4 Coarse Sand ) and

making good the wall etc . complete

NS-4 Providing and fixing uPVC 6 Kg/cm2 Soil , Waste &

RWP pipes (IS: 13592 Class B) including all fittings

(plain or door) e.g. bends, junction, cowls, offsets,

7 access pieces, jointing with rubber ring/solvent

cement joints including cutting chase or holes in

walls and floors and making good wherever required.

NS-5 Providing & fixing in position upvc P"or S" trap of self

cleaning design of following sizes for the embedded

areas Making proper connection with chemical

sealent joint , cutting chase / hole in floors /slabs

8 and bringing the same in proper condition in cement

concrete 1:2:4 mix complete as required. including

cost of cutting and making good the walls and floors

where required.

8.1 a) 110 mm inlet and 110 mm outlet 10.00 Each 734.00 7340.00

NS-6 Providing & fixing in position upvc floor drain

9 including cost of cutting and making good the walls

and floors wherever required.

9.1 a) 110 mm inlet and outlet 18.00 Each 451.00 8118.00

NS-7 Providing and fixing uPVC waste pipes for WB , SINK

, URINAL , FD (IS: 4985 ) 6 Kg / Sqcm including all

fittings (plain or door) e.g. bends, junction, cowls,

10 offsets, access pieces, jointing with rubber

ring/solvent cement joints including cutting chase or

holes in walls and floors and making good wherever

NS-13 Providing and fixing Cast bronze chrome plated

11 grating with ring and Stainless steel anti cockroach

basket and two SS screw including fixing to the floor

with cement mortar.

MR Providing and fixing UPVC inlet fitting with

maximum 3 inlets 32,40 or 50 mm size fabricated

12 from 110 mm dia UPVC pipes and fixed to upvc 7.00 Each 4682.00 32774.00

sockets,fixed to upvc trap with chemical sealent

joint and set in cement concrete as per standard

drawing complete.

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

NS-8 Providing and fixing upvc cleanout plug( Ceiling or

13 Floor) with suitable insert keys for opening, male

threaded joint with upvc socket fixed to uPVC pipe

complete in all respects.

13.1 a) 110 mm diameter Pipe 4.00 Each 538.00 2152.00

C. SUB HEAD- III - INTERNAL WATER SUPPLY

DSR -18.8 Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with

1 clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement

and the cost of cutting chases and making good the

same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making

good the walls etc.

1.1 18.8.1 15 mm nominal outer dia Pipes 35.00 Metre 497.80 17423.00

1.2 18.8.2 20 mm nominal outer dia Pipes 40.00 Metre 537.60 21504.00

1.3 18.8.3 25 mm nominal outer dia Pipes 40.00 Metre 627.25 25090.00

1.4 18.8.4 32 mm nominal outer dia Pipes 40.00 Metre 739.30 29572.00

DSR -18.7 Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of

Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25mm nominal bore 40.00 Metre 401.55 16062.00

18.7.4 32 mm nominal bore 40.00 Metre 518.75 20750.00

18.7.5 40mm nominal bore 50.00 Metre 702.95 35147.50

18.7.6 50mm nominal bore 120.00 Metre 934.15 112098.00

NS-9 Providing and fixing Thermoflex or Careflex thermal

insulation tubing, a elastomeric flexible material

having hermetic blister closed cell structure of

2 expanded synthetic rubber over pipes of following

nominal bores and thickness including all required

accessories complete as per specification.

9 mm thick ( Pipes in Chases)

2.1 a) For 15 mm dia Pipe 10.00 Metre 92.00 920.00

2.2 b) For 20 mm dia Pipe 50.00 Metre 101.00 5050.00

c) For 32 mm dia Pipe 20.00 Metre 120.00 2400.00

NS-10 Providing and Fixing full way lever operated forged

brass ball valve of brass body with forged brass hard

3 chromeplated steel ball tasted to a pressure not less

than 15 kg/sqcm with threaded / flanged joints

complete with nuts, bolts, gaskets, washers etc.

3.1 a) 15 mm dia nominal bore 2.00 Each 250.00 500.00

3.2 b) 20 mm dia nominal bore 5.00 Each 340.00 1700.00

3.3 c) 25 mm dia nominal bore 5.00 Each 512.00 2560.00

3.4 d) 32 mm dia nominal bore 4.00 Each 774.00 3096.00

3.5 e) 40 mm dia nominal bore 3.00 Each 1195.00 3585.00

NS-11 Providing, fixing, testing and commissioning of

motorised butterfly valve of following dia for filling of

overhead water tank complete with high and low

level control switches to control tanks. The level

controllers shall be installed in overhead tanks. The

4 level switch will close the valve when water level is

high in overhead tank and open the valve when

overhead water tank level is low. The system should

be complete in all respects with accessories 220 V AC

/ 24 V DC, IP67 electrical water level control unit,

copper control wiring in whether proof casing etc.

4.1 a) 40 mm dia nominal bore 1.00 Each 11393.00 11393.00

ELECTRICAL WORKS

SUBHEAD - I - CIRCUIT CUM POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

1 DSR 1.10 recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without

Independent switch etc.) with 1.5 sq. mm FRLS PVC

2 DSR-1.55 insulated copper conductor single core cable in

surface/ recessed PVC conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc as required. (Switch

Control Secondary Points)

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

3 DSR-1.3 recessed steel conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required. (Switch Control Primary

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

Independent switch etc.) with 1.5 sq. mm FRLS PVC

4 DSR-1.54 insulated copper conductor single core cable in

surface/ recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc as required. (Switch

Control Secondary Points)

MCB CONTROL LIGHT POINTS

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 2.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

5 NSI-1 recessed steel conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 2.5

sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required. (Switch Control Primary

5.1 NSI-1.1 Primary point controlled by one MCB. 12.00 Point 1535.50 18426.00

Same as item above but Secondary point. i.e. Points

5.2 NSI-1.2 to be looped with Primary point with 2.5 sqmm wire 12.00 Point 1365.90 16390.80

and Point wiring

Wiring for light/ power plug with 2X4 sq. mm FRLS

PVC insulated copper conductor single core cable in

6 DSR 1.5 surface/ recessed steel conduit alongwith 1 No. 4 sq. 300.00 Metre 433.00 129900.00

mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth

7 DSR 1.7 wire with the following sizes of FRLS PVC insulated

copper conductor, single core cable in surface/

recessed steel conduit as required.

7.1 DSR 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 50.00 Metre 327.00 16350.00

7.3 DSR 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 100.00 Metre 589.00 58900.00

7.4 DSR 1.7.5 2 x 10 sq. mm + 1 x 6 sq.mm earth wire 150.00 Metre 710.00 106500.00

7.6 DSR 1.7.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 60.00 Metre 1645.00 98700.00

Supplying and fixing suitable size GI box with

modular plate and

cover in front on surface or in recess, including

8 DSR 1.31 providing and 16.00 Each 477.00 7632.00

fixing 3 pin 5/6 A modular socket outlet and 5/6 A

switch, connections etc. as required.

Supply and Wiring for 250 volts single phase and

neutral 2 Nos 6 amps socket outlate with control by 1

No switched with 2.5 sq.mm PVC insulated copper

conductor 1100 volts grade stranded flexible FRLS

wires in concealed or surface mounted 25 mm dia

2mm thick PVC conduit including providing and

9 NSI-2 fixing of 6 amps 3 pin switch socket outlet of 14.00 Each 1796.31 25148.34

aprpoved make and design in 2 mm thick GI box

with grid plate and earthing of third pin of the

socket with 2.5 Sq. mm PVC insulated copper

conductor stranded flexible FRLS wire.(maximum

four no. of switches socket shall be connected on

Supplying and fixing suitable size GI box with

modular plate and

cover in front on surface or in recess, including

10 DSR 1.32 providing and 15.00 Each 586.00 8790.00

fixing 6 pin 5/6 & 15/16 A modular socket outlet and

modular switch, connections etc. as required.

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Supplying and fixing 3 pin, 5 A ceiling rose on the

11 DSR-1.33 existing junction box/ wooden block including 2.00 Each 87.00 174.00

connections etc. as required.

Supplying & fixing suitable size GI box wih modular

plate and cover in front on surface or in recess i/c

12 DSR-1.57 providing and fixing 25 amp modular socket outlet 2.00 Each 727.00 1454.00

and 25 Amps modular SP MCB, “ C ” curve including

connection, painting etc. as required. (AC's &

Supplying and fixing following modular switch/ socket

13 DSR 1.24 existing modular plate & switch box including

connections but

excluding modular plate etc. as required.

13.1 DSR 1.24.6 Telephone socket outlet 4.00 Nos 148.00 592.00

Supplying and fixing following size/ modules, GI box

14 DSR 1.27 modular base & cover plate for modular switches in

Supplying and fixing following size/ modules, GI box

15 DSR 1.24 modular base & cover plate for modular switches in

15.1 DSR 1.24.4 3 pin , 5/6 amps socket outlet 2.00 Each 122.00 244.00

Supplying and fixing following size/ modules, GI box

16 DSR 1.27 modular base & cover plate for modular switches in

Supplying and fixing of following sizes of medium

conduit along with accessories in surface/recess

17 DSR 1.21 including

cutting the wall and making good the same in case of

conduit as required.

Supplying and drawing following pair 0.5 mm dia

18.1 1.18 FRLS PVC insulated annealed copper conductor,

unarmored telephone cable in the existing surface/

recessed steel/ PVC conduit as required.

SUBHEAD - II - FITTINGS & FIXTURES

1 NSI-1 Supply, Installation, Testing and Commissioning of 9 6.00 Each 1778.35 10670.10

W Bulk head Light.

Supply, Installation, Testing and Commissioning of

5W Mirror Light.

Supply, Installation, Testing and Commissioning of

3 NSI-3 18W Recessed/Surface Mounted LED circular 76.00 Each 1975.94 150171.44

Supply, Installation, Testing and Commissioning of

20W Wall/Surface mouted 4 ft. LED

Supply, Installation, Testing and Commissioning of

65W Surface mounted LED Bay light.

Supply, Installation, Testing and Commissioning of

12W Recessed mounted LED circular Downlighter

6 NSI-6 (Cat no-Bajaj Lighting BGSLO SLEEK SURFACE 12W 40.00 Each 1167.60 46704.00

WH RD or equivalent as specified in the approved list

Supply, Installation, Testing and Commissioning of

7 NSI-7 150W highway with 150LPW Ceiling mounted LED 5.00 Each 7469.82 37349.10

Supply, Installation, Testing and Commissioning of

8 NSI-8 250W Highway with 130LPW ceiling mounted LED 12.00 Each 11204.73 134456.76

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Supply, Installation, Testing and Commissioning of

BEE 5 star rated, ceiling fan with Brush Less Direct

Motor, class of insulation: B, 3 nos. blades, 30 cm

long down rod, 2

nos. canopies, shackle kit, safety rope, copper

9 NSI-9 winding, Power Factor not less than 0.9, Service 8.00 Each 2730.00 21840.00

Value (CM/M/W) minimum 6.00, Air delivery

minimum 210 Cum/Min , 350 RPM (tolerance as per

IS : 374-2019), THD less than 10%, remote or

electronic regulator unit for speed control and all

remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 degree C (max.),

insulation resistance more than 2 mega ohm,

suitable for 230 V, 50 Hz, single phase AC Supply,

Supplying and fixing two module stepped type

electronic fan regulator on the existing modular plate

10 DSR 1.25 switch box including 8.00 Each 369.00 2952.00

connections but excluding modular plate etc. as

Installation, testing and commissioning of ceiling fan,

wiring the down rods of standard length (upto 30

sq. mm FRLS PVC insulated, copper conductor, single

etc. as required.

12 NSI-9 Supply of 300 mm dia Domestic Exhaust Fan 4.00 Each 2155.58 8622.32

13 NSI-10 Supply of heavy duty 450mm Wall Fan 10.00 each 6848.44 68484.40

Supply of heavy duty 600mm metal body industrial

SUBHEAD - III - MAIN BOARDS

Supplying, installing, testing & commissioning of

following type compartmentalised wall mounted /

floor mounted cubicle board made from 2mm thick

CRCA sheet dust & vermin proof duly phosphatized &

1 powder coated inclusive of suitable size 4 strip Al.

Busbar complete with interconnection providing Lugs,

inter-earthing, painting etc. i/c providing & fixing

below noted accessories:

Receiving,unloading,storing, handling, installation,

testing and commissioning of following MV

Switchboards complete as required and as per site

condition and dimension of all panels shall be carried

out as per the attachad sld

1 NSI-1 MAIN LT PANEL ( FOR BUILDING ) 1.00 Set 150808.00 150808.00

2 NSI-2 FIRE FIGHTING PANEL 1.00 Set 39705.00 39705.00

FEEDER PILLER FORMAIN HALL (OUTDOOR TYPE- IP

1 Nos. 100 amps 4P MCCB(15 KA)

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3

1 No. (0-100A) Ammeter with ASS with 3 nos.

1 Set of 200A TPN Aluminium Bus Bar with colour

coded PVC Sleeves

OUTGOINGS SECTION

1 Nos. 100A 4P MCCB (25 KA)

2 Nos. 63A 4P MCB (10 KA)

4 Nos. 40A 4P MCB (10 KA)

2 Nos. 32A DP MCB (10 KA)

Feeder Piller for main hallas described above

Supply and laying (including excavation, sand

cushioning, protective covering and refilling the

trench etc as required) of PVC sheathed PVC/XLPE

4 NSI-4 insulated Aluminium conductor/copper conductor 140.00 meter 1542.00 215880.00

power/ multicore control armoured cable of 1.1 KV

grade. 3 ½ C - 95 sq mm Aluminium cable

SUBHEAD - IV - DISTRIBUTION BOARDS

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240 V,

on surface/ recess, complete with tinned copper bus

1 DSR 2.3 bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

1.2 DSR 2.3.2 8 way, Double door 1.00 Each 2573.00 2573.00

1.3 DSR 2.3.3 12 way, Double door 2.00 Each 2315.00 4630.00

Supplying and fixing following way, three pole and

neutral, sheet steel, MCB distribution board, 415

volts, on surface/ recess complete with tinned copper

2 DSR 2.4 busbar, neutral busbar, earth bar, din bar,

detachable gland plate, interconnections,

phosphatized and powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing of following ways surface/

recess mounting, vertical type, 415 V, TPN MCB

distribution board of sheet steel, dust protected, duly

powder painted, inclusive of 200 A tinned copper bus

3 DSR 2.5 bar, common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer) as

required . (Note :Vertical type MCB TPDB is normally

used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V,

10 kA, "C" curve, miniature circuit breaker suitable

4 DSR 2.10 for inductive load of following poles in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole,

5 DSR 2.12 240 V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as

Supplying and fixing following rating, four pole, 415

6 DSR 2.13 V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as

Supplying and fixing following rating, double pole,

(single phase and neutral), 240 V, residual current

7 DSR 2.14 circuit breaker (RCCB), having a sensitivity current

30 mA in the existing MCB DB complete with

connections, testing and commissioning etc.

Supplying and fixing DP sheet steel enclosure on

8 DSR-2.16 surface/ recess along with 25/32 A 240 V "C" curve 3.00 Each 1169.00 3507.00

DP MCB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing single pole blanking plate in the

existing MCB DB complete etc. as required.

FIRE FIGHTING WORKS

A. SUB HEAD - A : PUMPS & EQUIPMENTS

1 18.4 Supplying , Installation , Testing and Commissioning

of Electric Driven Terrace Pump Suitable for

Automatic operation and Consisting of Following

Complete in all Respect as Required ( Terrace Fire

1.1 a) Horizontal Type Multistage , Centrifugal Pump of Cast

Iron Body and Bronze Impeller with Stainless Steel

Shaft Mechanical Seal Conforming to IS : 1520

1.2 b) Suitable HP Squirrel cage Induction motor , TEFC ,

synchronous speed 1500 RPM , Suitable for operation

on 415 Volts 3 Phase 50 Hz AC Supply with IP 68

protection for enclosure Horizontal Foot Mounted

type with class F insulation Conforming to IS : 325

with Energy Efficiency class IE-3

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

1.3 c) MS Fabricated Common Base Plate Coupling ,

Coupling Guard Foundation bolts etc as Required

1.4 d) Suitable Cement Concrete Foundation duly Plastered

with anti vibration Pads

The Head of the Pump is Selected in a manner so as

to give a minimum 3.5 kg/sqcm pressure at the

highest / farthest point

2 18.20 Supplying and Fixing Air Vessel made of 450 mm dia

8 mm thick ms sheet 2000 mm in height with air

release valve on top and flanged connection to riser

drain arrangement with 25 mm dia gunmetal wheel 2.00 Set 18244.00 36488.00

valve with required accessories pressure gauge and

painting with synthetic enamel paint of approved

shade as required

B. PIPING, HYDRANT , AND ACCESSORIES SYSTEM

1 18.7 Providing Laying Testing and Commissioning of C

class Heavy duty MS Pipe Conforming to IS : 1239 /

3589 including Fittings like elbows , tees , flanges ,

tapers , nuts , bolts , gaskets etc in ground including

welding excavation and Providing cement concrete

blocks as supports anticorrosive treatment with

coaltar / asphalts tape as per IS :10221 refilling the

trench etc of following sizes complete as required .

2 18.11 Supplying Fixing Testing and Commissioning of

butterfly valve of PN 1.6 Rating with Bronze

Gunmetal Sheet duly ISI marked complete with nuts

, bolts , washers , gaskets conforming to IS : 13095

of following sizes as required .

3 18.14 Providing Installation Testing and Commissioning of

Non Return Valve of following sizes conforming to IS

: 5312 complete with rubber gasket , GI Bolts , Nuts

, washers etc as required .

4 18.15 Providing Installation Testing and Commissioning of

Stainless Steel Y Strainer fabricated out of 1.6 mm

thick stainless steel , Grade 304 , Sheet with 3 mm

dia holes with stainless steel flange .

5 18.9 Supplying and Fixing Single Headed Internal Hydrant

Valve with instantaneous gunmetal material coupling

of 63 mm dia with cast iron wheel ISI marked

conforming to IS : 5290 ( Type A ) with blank

Gunmetal material cap and chain as required .

5.1 18.9.1 Single Headed Gunmetal Material 3.00 Set 7646.00 22938.00

6 18.13 Supplying and Fixing orifice plate made out of 6 mm

thick stainless steel ( Grade 304 ) with orifice of

required size to be fitted between flange and landing 4.00 Each 1321.00 5284.00

valve of external and internal hydrants to reduce

pressure at the outlet to the level of 3.5 kg / sqcm

complete as required .

7 18.16 Supplying and Fixing 63 mm dia 15 m Long RRL Hose

pipe with 63 mm dia male and female coupling duly

bound with GI wire , rivet etc . Conforming to IS :

636 ( Type A ) as Required .

7.1 18.16.1 Gunmetal Material 3.00 Set 5202.00 15606.00

8 18.17 Supplying and Fixing First aid hose reel with MS

Construction Spray painted in Post office red

conforming to IS : 884 complete with the following

20 mm nominal internal dia water hose thermoplastic

( Textile Reinforced ) Type - 2 as per IS : 12585

20 mm nominal internal dia gunmetal globe valve

Drum and Brackets for fixing the equipments on wall

Connections from Riser with 25 mm dia stop

gunmetal valve and MS Pipe and socket

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

9 18.18 Supplying and Fixing 63 mm dia Gunmetal Short

Branch Pipe with 20 mm nominal internal diameter

size nozzle conforming to IS : 903 suitable for

instantaneous connection to interconnect hose pipe

coupling as required .

9.1 18.18.1 Gunmetal Material 6.00 Set 2416.00 14496.00

10 18.22 Providing and Fixing of Pressure Switch in MS Pipe

Line including connection etc as required

11 NS-1 Providing and fixing of Fire Hose Cabinet size not less

than 2.1 x 1.2 x 0.90 mtr made out of M.S. sheet

not less than 1.5 mm thick having central opening

and 4 mm thick glazed glass doors (Two nos.)

suitably marked on the outside 'with the letters

"FIRE HOSE" including necessary locking 3.00 Each 30495.00 91485.00

arrangement and painting in PO red colour suitable

to accommodate, internal hydrant valve, 2 nos 15

mtr long Hose pipe, branch pipe, nozzle and fire

man's axe. It shall be fixed inside the FHC Cabinet

Complete as required .

12 NS-2 Providing and fixing weather proof Fire Hose Cabinet

of size not less than 0.75 x 0.6 x 0.25 mtr made out

of M.S. sheet not less than 1.5 mm thick having

central opening and 4 mm thick glazed glass doors

(Two nos.) suitably marked on the outside 'with

the letters "FIRE HOSE" including necessary locking 3.00 Each 11854.00 35562.00

arrangement and painting in PO red colour suitable

to accommodate, external yard hydrant valve, 2 nos

15 mtr long Hose pipe, branch pipe, nozzle and fire

man's axe. It shall be mounted on boundary wall

complete as required.

13 NS-3 Providing & fixing Controlled Percolating (CP) Hose

ISI marked (IS:8423) 63 mm dia x 15 m long

complete with instantaneous type Stainless steel 63

mm dia ISI marked Male & Female couplings 6.00 Each 5081.00 30486.00

(IS:903) bound and riveted to hose pipe with copper

rivets and 1.5 mm copper wire.brusting pressure not

less than 22 Kg/Sqcm. ( Two nos. for each

14 NS-4 Providing and fixing standard firemans axe with

heavy rubber handle.

15 NS-5 Providing and fixing dial type pressure gauge with

isolation cock and copper pipe on main header Dial 12.00 Each 3458.00 41496.00

diameter 100 mm celebration 0-16 / sq. cm.

16 NS-6 Providing and fixing Fire Extinguishers (CO2 type

powder ) 4 Kg Capacity complete with all 1.00 Each 5647.00 5647.00

accessories as per manufacturers specifications.

17 NS-7 Providing and fixing Fire Extinguishers (A, B, C type

powder ) 5 Kg Capacity complete with all 14.00 Each 4518.00 63252.00

accessories as per manufacturers specifications.

FIRE ALARM CONVENTIONAL SYSTEM

Supplying, installation, testing & commissioning

sector panel suitable for following zones, complete

with visual indications for short circuit fault, open

1 DSR 17.1.9 circuit fault, fire condition and all other standard

facilities as per IS:2189 with mimic diagram for all

area/zone covered, complete with all connections,

interconnections as required

Supplying, installation, testing & commissioning of

conventional beam detector with short circuit isolator

2 NS-1 (inbuilt or seperate) complete with emitter and 2.00 Nos. 43644.00 87288.00

receiver including connections with remote test

features etc complete as

Supplying, installation, testing & commissioning of

3 DSR 17.1.2 smoke detector with builtin LED and mounting base 10.00 Nos. 1153.00 11530.00

complete with all connections etc. as required

Supplying, installation, testing & commissioning of

manual call boxes of MS construction in

4 DSR 17.1.3 surface/recess with stainless steel chain & hammer 4.00 Nos. 474.00 1896.00

assembly complete with glass and push button etc.

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Supplying, installation, testing & commissioning fire

alarm sounder with facility to make announcement,

5 DSR 17.1.6 mounted in M.S. box (16 SWG) with hinged cover 4.00 Nos. 557.00 2228.00

plate & suitable for operation with amplifier i/c line

matching transformer etc. complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm

armoured cable, 600/1000V rated with annealed

6 DSR 17.5.2 copper conductor having XLPE insulation, steel wire 160.00 Mtrs 173.00 27680.00

armouring & FRLS outer sheath complete as

Supplying and fixing of following sizes of steel

conduit along with accessories in surface/recess

7 DSR 1.20 including painting in case of surface conduit, or

cutting the wall and making good the same in case of

recessed conduit as required.

Supply, Installation, Testing & Commissioning of

Speaker with below Specifications:-

Transducer Size : 15" LF Driver + 1 x 1" Horn-loaded

Compression Driver

Power Handling : 300 Watts Continuous, 1200W Peak

Dispersion : 90 x 40

Sensitivity : 101 dB

Max SPL : 124dB continuous, 130 dB peak

Approved Makes: OHM, British Acoustics, JBL, Bose,

Supply, Installation, Testing & Commissioning of

Subwoofer with below Specifications:-

Transducer Size : 18" Low Frequency Driver

Power Handling : 600 Watts Continuous, 2400W Peak

Freq. Range : 45 Hz - 300 kHz

2 NS Dispersion : Omni-directional, 2.00 Nos 115000.00 230000.00

Sensitivity : 101 dB

Max SPL : 129dB continuous, 135 dB peak"

Approved Makes:OHM /British Acoustics/ Bose/

British Acoustics

Supply, Installation, Testing & Commissioning of

Class-D Power Amplifier with below Specifications:-

Number of Channels : 2

Power at 4 Ohms per channel : 1000W

Power at 8 Ohms per channel : 500W

NS Class-D with LCD Display for critical factors, dual 2.00 Nos 90000.00 180000.00

step power factor correction, built in crossover to set

HPF & LPF Filters

Approved Makes: OHM /British Acoustics/ Bose/

British Acoustics

Supply, Installation, Testing & Commissioning of

Software Controlled Digital DSP with below

Specifications:-

Number of Inputs - 4,

Number of Outputs - 8,

Input Impedance - 12k Ω unbalanced, 24 k Ω

Adjustable Delay - 1 second / input & 1 second /

Approved Makes: OHM /British Acoustics/ Bose/

British Acoustics

3 NS Supply of Flying bar for above speakers 2.00 Nos 20000.00 40000.00

Supply of Stage Monitor Supply of Stage monitor 2-

way, bi-amp. bass reflex design, 400+100W rms ,

4 NS 75Hz-16KHz freq resp, 12" woofer, 1"HF driver, 2.00 Nos 46000.00 92000.00

130dB SPL max, Disp 90 ° , polyprop molded

enclosure . Approved Makes: OHM /British Acoustics/

Bose/ British Acoustics

Supply of Audio mixer 24 mono mic inputs 4 line

inputs Freely assignable faders and patching Pre/Post

selection per input per bus AES in and out Global

mode encoders FaderGlow ™ GEQ on every bus 20

sub-group / aux busses 4 FX busses 8 Matrix busses

5 NS LR and C Mix busses 4 Stereo Lexicon Effects 1.00 No. 86000.00 86000.00

engines Delay on inputs and outputs 4 Mute Groups

Freely assignable insert loops Harman HiQnet

integration Colour touch screen interface Approved

Makes: (Si Expersion-2)(Allen Heath QU 24)/ (OSL

Supply of Corded microphone (Shure-

SM58/OSL/sennheiser)

Supply of Instrument Microphone(Shure-

57/OSL/sennheiser)

8 NS Supply of Podium Microphone (Shure/OSL/AKG) 2.00 Nos 28411.00 56822.00

9 NS Supply of Microphone Stand Big(GS) 2.00 Nos 1124.00 2248.00

10 NS Supply of Microphone Stand Small(GS) 2.00 Nos 843.00 1686.00

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Supply of microphone cable from stage to control

11 NS room for microphone points with conduit pipe etc. 300.00 Mtr 80.00 24000.00

(Belden/Klotz/Netmas)

Supply of Speaker 2.5sqmm x3core

(Belden/Klotz/Netmas)

Supply of microphone connecting box made out

from CRC sheet metal box duly powder coated

13 NS paint,with 6 nos XLR panel mounting socket & phono 4.00 Nos 6322.00 25288.00

socket having the facility to connect the 6nos

microphone channel.

Supply of Professional Head phone(German

Meastro/Sennheiser/OSL)

Supply of Microphone cable XLR to XLR up to 10 Mtr

(Belden/Klotz/Netmas)

Supply of Microphone cable XLR to XLR up to 15 Mtr

(Belden/Klotz/Netmas)

Supply of Speaker connectin connector & MCB Box

for Speaker etc

18 NS Installation charges 1.00 Job. 80000.00 80000.00

SUB TOTAL 1219768.00

EXTERNAL DEVELOPMENT WORK

A PQC ROAD FOR 3.5 MTR WIDE & 10.0 MTR LONG ROAD

Preparation and consolidation of sub grade with

power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm depth,

1 16.1 dressing to camber and consolidating with road roller 75.00 Sqm 218.90 16417.50

including making good the undulations etc. and re-

rolling the sub grade and disposal of surplus

earthwith lead upto 50 metres.

Construction of granular sub-base by providing close

graded Material conforming to specifications, mixing

in a mechanical mix plant at OMC, carriage of mixed

material by tippers to work site, for all leads & lifts,

2 16.78 spreading in uniform layers of specified thickness cum

with motor grader on prepared surface and

compacting with vibratory power roller to achieve the

desired density, complete as per specifications and

directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75

mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base

over a prepared sub-grade with coarse and fine

aggregate conforming to IS:383, the size of coarse

aggregate not exceeding 25 mm, aggregate cement

ratio not to exceed 15:1, aggregate gradation after

blending to be as per specifications, cement content

not to be less than 150 Kg/cum, optimum moisture

content to be determined during trial length

construction, concrete strength not to be less than

10 Mpa at 7 days, mixed in a batching plant,

transported to site, for all leads & lifts, laid with a

mechanical paver, compacting with 8-10 tonne

vibratory roller, finishing and curing etc. complete as

per direction of Engineer in- charge.

Providing and laying C.C. pavement of mix M-25 with

ready mixed concrete from batching plant. The ready

mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and

finally finished by floating, brooming with wire brush

etc. complete as per specifications and directions of

5 16.75 Engineer-incharge. 4.38 cum 9823.80 42979.13

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this item is @

Excess/less cement used as per design mix is

payable/ recoverable separately).

Providing and filling in position rubberized bitumen Per cm

hot sealing compound for sealing of expansion joints width

in roads / pavements all complete as per direction of per

6 16.46.1 the Engineer-in-Charge. 131.25 cm 8.65 1135.31

Using grade 'A' sealing compound conforming to IS: depth

Providing and laying at or near ground level factory

made kerb stone of M-25 grade cement concrete in

position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or without

grooves (thickness of joints except at sharp curve

7 16.69 shall not to more than 5mm), including making 0.81 Cum 10117.60 8195.26

drainage opening wherever required complete etc. as

per direction of Engineer-in-charge (length of

finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved

by Engineer-in-charge).

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

8 2.25a lead of 5km also including ramming and watering of 8.50 cum 700.50 5954.25

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

Painting with synthetic enamel paint of approved

brand and manufacture of required colour to give an

Two or more coats on new work over an under coat

9 13.62.1 of suitable shade with ordinary paint of approved 9.00 sQM 226.25 2036.25

brand and manufacture

FOOTPATH 2.00 MT. WIDE(FOR 10.00 X 2.00 =

1. Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth. 1.5 m in width as well as

10 sqm on plan) including disposal of excavated

earth, lead upto 50m and lift upto 1.5m, disposed

earth to be levelled and neatly dressed.

2.6.1 all kinds of soil 10.63 Cum 177.50 1887.05

2 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering. All work upto plinth level.

1:5:10 (1 cement : 5 course bound: 10 graded stone

4.1.10 aggregate 40mm nominal size)

3 16.68 Providing and laying 60mm thick faciory made

cement concrete interlocking paver block of M -30

grade made by block making machine with strong

vibratory compaction, of approved s;ze, design &

shape, laid in required colour and pattern over and 686.00 Sqm 972.00 666792.00

including 50mm thick compacted bed of coarse sand,

filling the joints with line sand etc. all complete as

per the direction of Engineer-in-charge.

4 Providing and laying at or near ground level factory

made kerb stone of M-25 grade cement concrete in

position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), ncluding making joints with or without

grooves (thickness of joints except at sharp curve

shall not to more than 5mm), including making

drainage opening wherever required complete etc. as

per direction of Engineer-in-charge (length of

finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by

16.69 Engineer-in-charge).

5 Painting with synthetic enamel paint of approved

brand and manufacture of required colour to give an

Two or more coats on new work over an under coat

of suitable shade with ordinary paint of approved 16.88 Sqm 226.25 3817.97

13.62.1 brand and manufacture

6 Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

lead of 5km also including ramming and watering of 30.38 Cum 700.50 21277.69

the earth in layers not exceeding 20 cm in trenches,

sides of foundation etc. complete.

7 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of oundations etc. in layers

not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

8 Centering and shuttering including strutting,

propping etc. and removal of form for all heights :

a Foundations, footings, bases of columns, etc. for

5.9.1 mass concrete.

SUB HEAD- V EXTERNAL WATER SUPPLY

MR Supplying, installing, testing and commissioning

vertical on line multi stage centrifugal pumping set

with mechanical seal, C.I. volute and SS impeller &

SS shaft connected to a TEFC induction motor of

suitable HP for 415 volts, 3 phase, 50 cycles A.C.

supply with 150 mm dia pressure gauge with

SS/gunmetal isolation cock, vibration eliminating

pads, base plate wiring upto panel and equipment for

water level controller to start and stop the pump

automatically at predecided levels of the water in the

tank with provision of protection for dry run etc.

complete in all respect (The shop drawing or the

pumps along with its characteristics curves, model

and technical data etc. are to be submitted for

approval before purchase of pump).

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Domestic water pumps (Treated water transfer pump

to terrace tank) (1W+1S)

Capacity 50 lpm

18.10 Providing and fixing G.I. pipes complete with G.I.

fittings and clamps, i/c cutting and making good the

Internal work - Exposed on wall

18.10.6 50 mm dia nominal bore 21.00 RMT 1048.35 22015.35

18.12 Providing and fixing G.I. pipes complete with G.I.

fittings including trenching and refilling etc.

SUB HEAD- IV EXTERNAL SEWARAGE LINE

2.1 Excavating trenches of required width for pipes,

cables, etc including excavation for sockets,

anddressing of sides, ramming of bottoms, depth up

to 1.5 m, including getting out the excavated soil,

and then returning the soil as required, in layers not

exceeding 20 cm in depth, including consolidating

each deposited layer by ramming, watering, etc. and

disposing of surplus excavated soil as directed,within

a lead of 50 m :

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but not

exceeding 300 mm dia

19.4.1.1 Providing and fixing square-mouth S.W. gully trap

class SP-1 complete with C.I. grating brick masonry

chamber with water tight C.I. cover with frame of

300x300 mm size (inside) the weight of cover to be

not less than 4.50 kg and frame to be not less than 7.00 EACH 2707.65 18953.55

2.70 kg as per standard design: 100x100 mm size P

type. With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

19.7 Constructing brick masonry manhole in cement

mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C.

top slab with 1:2:4 mix (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size),

foundation concrete 1:4:8 mix (1 cement : 4 coarse

sand : 8 graded stone aggregate 40 mm nominal

size), inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished with

floating coat of neat cement and making channels in

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size)

finished with a floating coat of neat cement complete

as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455x610 mm internal

dimensions,total weight of cover and frame to be not

less than 38 kg (weight of cover 23 kg and weight of

19.7.1.1 With common burnt clay F.P.S.(non modular) bricks

of class designation 7.5 8.00 EACH 12770.55 102164.40

19.28 Constructing brick masonry road gully chamber

45x45x77.5 cm with bricks in cement mortar 1:4 (1

cement : 4 coarse sand ) with precast R.C.C. vertical

grating complete as per standard design :

19.28.1 with common burnt clay F.P.S.(non module) brick of

class designation 7.5

19.1 Providing, laying and jointing glazed stoneware pipes

class SP-1 with stiff mixture of cement mortar in the

proportion of 1:1 (1 cement : 1 fine sand) including

testing of joints etc. complete :

19.2 Providing and laying cement concrete 1:5:10 (1

cement : 5 coarse sand : 10 graded stone aggregate

40 mm nominal size) all-round S.W. pipes including

bed concrete as per standard design :

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

19.21 Making connection of drain or sewer line with existing

manhole including breaking into and making good

the walls, floors with cement concrete 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate

20 mm nominal size) cement plastered on both sides

with cement mortar 1:3 (1 cement : 3 coarse sand),

finished with a floating coat of neat cement and

making necessary channels for the drain etc.

19.21.1 For pipes 100 to 250 mm diameter

19.9 Constructing brick masonry circular type manhole

0.91 m internal

dia at bottom and 0.56m dia at top in cement mortar

: 4 coarse sand), inside cement plaster 12 mm thick

mortar 1:3 (1 cement : 3 coarse sand) finished with

a floating coat

of neat cement, foundation concrete 1:3:6 mix (1

cement : 3 coarse

sand : 6 graded stone aggregate 40 mm nominal

size), and making

necessary channel in cement concrete 1:2:4 (1

cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal

with a floating coat of neat cement, all complete as

19.9.1 0.91 m deep with SFRC cover and frame (heavy

20 grade designation) 560 mm internal diameter

to I.S. 12592, total weight of cover and frame to be

less than 182 kg., fixed in cement concrete 1:2:4 (1

: 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including centering, shuttering all

(Excavation, foot rests and 12mm thick cement

the external surface shall be paid for separately) :

19.9.1.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

SURFACE DRAIN (250X150 MM)

1 Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m,

as directed by Engineer-in-charge.

2.6.1 all kinds of soil 43.00 cum 177.50 7632.50

2 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

not exceeding 20cm in depth: consolidating each 11.00 cum 196.00 2156.00

deposited layer by ramming and watering, lead up to

50 m and lift up to 1.5 m.

Qty. = 25% of them no 1

3 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

4.1 shttering - All work up to plinth level

1:5:10 (1 cement : 5 coarse sand (zone-III): 10

graded stone aggregate 40 mm nominal size). 9.00 cum 6518.60 58667.40

4 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived

from natural sources : 4 graded stone aggregate 40 3.00 cum 7780.30 23340.90

mm nominal size derived from natural sources)

5 Centering and shuttering including strutting,

propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for

5.9.1 mass concrete

6 Brick work with F.P.S. bricks of class designation 75

in foundation and plinth in :

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 7.00 Cum 7132.25 49925.75

7 12 mm cement plaster finished with a floating coat of

13.7 neat cement of mix :

External Electrification

DSR /NSI Description RATE AMOUNT

ITEM CODE DSR MR MR

Earthing with G.I. earth plate 600 mm X 600 mm X 6

mm thick including accessories, and providing

1 DSR 5.4 masonary enclosure with cover plate having locking 1.00 Sets 7472.00 7472.00

arrangement and watering watering pipe 2.7 metre

long etc. with charcoal/ coke and salt as required.

Earthing with Cu. earth Plate 600mm x 600mm x

3mm thick including accesssories, and providing

2 DSR 5.6 masonary enclosure with cover plate (CI heavy 1.00 Sets 13838.00 13838.00

duty) having locking arrangement and watering pipe

pipe of 2.7 mtr long etc. with charcoal or coke and

salt) as required.

Supplying and laying 25 mm X 5 mm G.I. strip in 40

3 DSR 5.11 mm dia G.I. pipe from earth electrode, including 20.00 Mtr 706.00 14120.00

connection with G.I. nut, bolt, spring, washer

excavation and refilling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on

4 DSR-5.14 surface or in recess for connections etc. as required. 20.00 Mtr 1162.00 23240.00

2 nos used for 50 x 5 for the Neutral earthing of

Providing and fixing 25 mm X 5 mm G.I. strip on

5 DSR 5.15 surface or in recess for connections etc. as required. 20.00 Mtr 244.00 4880.00

Providing and fixing 6 SWG dia G.I. wire on surface

6 DSR 5.16 or in recess for loop earthing etc. as required. 20.00 Mtr 70.00 1400.00

Supplying, fixing, testing and commissioning of

7 NSI-1 following bare Copper/ GI flat including all necessary

fixing accessories and effecting connections.

Supply and laying medium class GI pipe under

8 NSI-2 road/paved areas/wall crossing etc. including earth

excavations refilling, ramming and making good as

8.1 NSI-2.1 150 mm dia GI pipe Class B 10.00 Metre 1600.00 16000.00

SUPPLYING & LAYING OF CABLE

Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

1 DSR 7.1 following size direct in ground including excavation,

sand cushioning, protective covering and refilling the

Laying of one number additional PVC insulated and

PVC sheathed / XLPE power cable of 1.1 KV grade of

2 DSR 7.2 following size direct in ground in the same trench in

one tier horizontal formation including excavation,

sand cushioning, protective covering and refilling the

trench etc. as required.

Supply of following sizes of XLPE insulated

Aluminum conductor strip/ wire Armoured, overall

3 NSI PVC sheathed 1.1 KV grade cables conforming to

relevant IS-7098 Code and technical specifications.

Supplying and making end termination with brass

compression gland and aluminium lugs for following

4 DSR 9.1 size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade

Supplying, installation, testing and commissioning of

65W LED Street Light IP66 LED with High

performance having system lumen output of

minimum 9900 lumens, contemporary designed

1 NSI-1 housing made of die-cast aluminium, with street 4.00 Nos 7634.33 30537.32

optic LENS for uniform light distribution. PF better

than 0.9, CRI better than 70 complete with all

accessories. Wipro Cat No.: LR 02-102-XXX-57-G2

SITC of 6m ht. GI pole alongwith control box,6A MCB

etc. as required for St. height

GRAND TOTAL 40068890.26

GRAND TOTAL 40068890.26