CERTAIN REPAIR TO OTM ACCN ALONG DEEPNAGAR ROAD INCL ALL OFFRS MESSES AND CE OFFICE, VAPPS, MR BAY, VSI, BOYS HOSTEL S AND T LINE AREA UNDER AGE B/R-II OF GE (EAST) JALANDHAR CANTT

Amount

Taking down cement plaster of any description thickness including raking out joints hacking for key scrubbing down with water all as specified and directed.

M&L for 15 mm thick cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement all as specified and directed

M&L 15mm thick cement plaster in cement mortar 1:4 with water proofing compound on external surface brick or concrete surface finished even and fair without using extra cement all as specified and directed (WPC shall be measured and paid seperately)

"Supply only" Integral waterproofing compound (ISI Marked).

M&L Plastering 5mm thick in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified and directed

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of ceiling surfaces all as specified and directed

M&L for preparing surfaces plastered or unplastered surfaces of walls by applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for prepration of new surfaces of walls including cornices, plasters etc (Plastered or unplastered surfaces) and applying two coats of cement base paint over a coat of primer.

M&L for prepration of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil bound distemper.

Complete removal of existing treatment on walls by scrapping washing rubbing down etc and applying two coat of cement base paint all as specified and directed and directed.

M&L for 25 mm thick cement concrete type B-1, 1:2:4 (20 mm graded aggregate) to receive the top layer of tiles

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified and directed

M&L for non-skid ceramic coloured tiles (Premium quality) 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry and pointed in while or colored cement to match over and incl 15mm thick bedding layer CM 1:6 in roughening of old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust inc brushing neat cement slurry with 3 kg/sqm complete all as specified and directed. Make;- Somani/Kajaria/Johnson as approved by GE.

All as per description of item No 13 above but in skirting and 10mm thick rendering as backing coat of CM 1:4

M&L for coloured glazed tiles (Premium quality) of size 300x450x6 - 7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4 Make:- Somani/Kajaria/Johnson as approved by GE.

M&L Vitrified ceramic coloured/designed tiles (Premium quality) light shade of size 10mm thick area of each tile not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointing in white and coloured cement to match colour tiles over and incl 15mm thick screed bed in CM 1:6 all as specified and directed. Make:- Somani/Kajaria/Johnson as approved by GE.

Ditto as per description of item No 16 here-in-before but in skirting and 10mm thick rendering as backing coat of CM 1:4

M&L for 18 to 20 mm thick machine cut kota stone slab flooring (550mm X 550 mm size) over and incl 15mm thick bedding layer CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and mirror/granite finish polishing complete all as specified and as directed.

All as per item No 18 above but on vertical surfaces such as skiting dodo, riser etc over and incl 10 mm thick cement plaster in CM 1:4 rough finished surface to receive tiles complete all as specified and as directed.

S&F 18 to 20 mm thick granite (of any type) tiles machine cut , in skirting/dado, pillars laid over cement screed 15 mm thick in CM 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

M&L for Dholpur stone as on wall clading with machine cut face work, pillers, arches, haxogonal roof pillar and all facing etc of 15 to 18 mm thick one side single length laid and jointed in cement and sand mortar 1:2 including araldite chemical and recess pointing pointed with an admixture of white cement and dholpur stone dust 1:1 and making edges, work in small patches, stone shall be of uniform colour of each stone and size not exceeding 0.20 Sqm each fixed, over & including 15 mm thick cement plaster in CM (1:4) on brick or concrete wall surfaces finished rough surfaces to reveive tiles incl dismantling of stone complete all as specified and directed and directed.

Demolition of reinforced cement concrete in ground floors and paving n. exc 15 cm thickness (reinforcement to cut as required to facilitate demolition) all as specified and directed.

M&L for reinfored cement concrete type B-1 1:2:4 (20 mm graded crushed stone aggregate) slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for MS TMT bars 10 mm and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for clos hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia.

M&L for form work to soffits of suspended slabs such roof slabs, floor slabs, shelves, landings and similar work, not exceeding 200mm thick (horizontal or slopping) rough finished surfaces of concrete flat or shelfs etc.

Formwork to edges of concrete flats, breaks in floors, window cills , concrete raillings, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding10cm but not exc 20 cm wide rough finished surfaces of concrete all as specified and directed.

Dismatnling plain or corrugated steel/asbestos sheeting any gauge, thickness, including Nainital or similar pattern roof coverings.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. Make:- TATA/JSW/Indian Ispat.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F in repair 4 mm thick fibre glass reinforced translucent plain sheeting fixed with coach screw and washer in roof, wall upto 8 meter height complete all as specified and directed and directed

S&F Rolled mild steel work roof trusses (framed),trussed, purlins, rafters,crane gantries and heavy brackets framing (beams,tee,angle,channel or flat section) including MS plates, nutt bolts etc complete conforming to Fe 410-W(GdeE-250) quality B

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area exc 1.5 Sqm and not exc 4 Sqm each.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each

S&F 35mm thick IInd class hard wood plain framed factory made paneled shutters with (2 panel ) of 9mm BWP commercial ply of 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I) kiln seasoned and chemically treated complete all as specified and directed.

S&F 40mm thick flush shutter factory made, solid core construction, with block board core and ply wood face pannel, commercial type both sides complete all as specified and directed.

S&F glazed and skelton shutters factory made 35mm thick open rebated and prepared to receive glass,gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I, Section 8, Clause 8.24(a) complete all as specified and as directed.

M&L for pressed steel frame of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges,lock strike plate etc as per IS specifications complete all as specified and directed and directed

M&L for pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges,lock strike plate etc as per IS specifications complete all as specified and directed and directed

S&F steel window 1.25 mm thick Box type (Primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed and gauzed skelton shutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWRR box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fittings welded to failed shutters (Hold fasts 150 mm long of 12 mm x 3 mm made to shape-04 nos per window. (b) Handle of Z sec 20 mm x 25 mm, 100 mm long-1 Nos of leaf (c) MS tower bolt 150 mm long 02 Nos per leaf. (d) Z sec 20 mm x 25 mm , 100 long of hollow square 15 mm x 20 mm x 63 mm welded to hinges – 01 Nos per leaf (f) MS pintal hinges of size 75mm x 12 mm -02 Nos per lear (g Fabrication and fixing arrangement as per drawing No CEJZ/TD -06/07 Make/manufacture by Tee Pee Enterprises Amritsar, M/s Ram fabricators Pvt Ltd PanchKula. Note Glass and painting shall be measured and paid separately under appropriate items.

Ditto as per description of item No 40 above but in ventilators

S&F mild steel framed work such as guard bars/grills, grating etc with end of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, railings etc and similar works including one shop coat of zinc chromate primer complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks.

Ditto as per description of item No 43 above but fixed in repair

Hacking out old broken glass (any thickness, size quality or description) from wooden or steel frame glazed with putty or fixed with beads.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty wooden beads in square mtr n.exc 0.50 sqm each pane complete

M&L for 3 mm thick plain figure glass, pin headed type and fixing and glazing with in oil putty in sqaure n exc .5 sqm in each pane.

Dismantling structural steel works as in grills, doors ,gates , purlin, rafter etc

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, suppling and fixing in opening as per specification and drawing.

S & F in repair floor spring door closer for aluminium door in any size brass and chromium plated body approved quality including carefully taking down the existing door and removing the damaged floor door closer and accessories etc and refixing the same door on the new door closer and making good the floor area and match the surface complete work all as specified and directed and directed by Engr-in-Charge

Repair to existing aluminium door/ window in any size including carefully taking down the existing door/ window and removing the damaged aluminium fittings and accessories etc and refixing the same door/ window with new fittings on same opening and making good the floor/ wall area and match the surface complete work all as specified and directed and directed by Engr-in-Charge

S&F in repair aluminium (extruded section body) door closer hydraulically regulated designation No 2 universal type suitable for door shutters of 701 to 850 mm in width and weight of between 36 to 60 kg and fixed complete all as specified and directed and directed

M&L Powder coated Aluminium door shutter having 150mm x 44mm x 2.85mm thick bottom rail,150 mm x 44mm x 3mm thick middle rail, 100mm x44mm x2.85 mm thick stile and top rail including necessary fitting joinery cleat, glazing packing snap beading 10 mm x 10 mm , powder coated aluminium handle 200 mm long (02 Nos) , 3 Nos 100 mm size chromium plated butt hinges, 2 Nos 200mm size Aluminium tower bolt and Aluminium body hydraulically door closer , designation No-3, universal type, weight between 61 to 80 kg etc inlcuding frame of section 100 mm x 44 mm x2.85 mm and door shutter, bottom portion covered with 9mm thick prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination (colour/design approved by Engr-in-Charge) fixed to powder coated Aluminium frame work and top portion covered with 5.00 mm thick tinted glass and pattern, one mortic lock (Make: Harrison ) with shutter and fixing including taking down of existing Chowkat with Shutter complete all as specifies and directed by Engineer-in-Charge Make of aluminium section Hindalco/Jindal

M&L Powder Coated Aluminium window/ ventilator shutter side hung having 75 mm x 44 mm x2.85 mm thick stiles bottom rail and top rail including necessary ftting joinery cleat glasing packing snap beading 10 mm x 10 mm , 2 nos of powder coated aluminium handle 150 mm size, 2 nos of chromium pated butt hinges 75 mm size and 2 nos of 100 mm long Alu tower bolt etc inlcuding frame of section 100 mm x 44 mm x 2.85 mm and including 5.00 mm thick tinted glass and including aluminium grill and fixing including taking down of existing Chowkat with Shutter complete all as specified and directed & directed by Engineer-in-Charge. Make of aluminium section Hindalco/Jindal

S&F 250mm long Aluminium alloy, anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy fixed complete all as specified and directed.

Supply & Fixing 100mm size butt hinges medium weight cold rolled mild steel all as specified and directed.

S&F100mm size stainless steel butt hinges for fixing to PVC doors all as specified and directed.

S&F 200mm long mild steel tower bolt stove enamelled black with bright bolt all as specified and directed.

S&F 150 mm mild steel pressed handles oval type, stove enamelled black all as specified and directed.

Preparation of new wood and wood based surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel surface of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

S&F aluminium anodised barrel tower bolt of extruded section 200 mm long fixed with machine screws.

S&F aluminium anodised bow handle 150 mm long fixed with machine screws.

S&F in repair mild steel 300 mm ordinary rat rail rod pattern springs including roller and roller plate complete.

Dismantling wall and ceiling boards any type, any thickness and any shape including cover fillets and frame work.

M&L 6mm thick asbestos fibre cement plain building boards fixed to frame work with screws as in flat ceiling

S&F hollow PVC Wall Lining consisting of 7mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site all as per specified and directed.

Supply & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 6mm thickness (as per IS: 14862) of size 595x595 mm and any one of the desin (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length, and 15x32mm made from 0.30 mm thick sheet, and cross "T" of size 15x32mm made of 0.30 mm sheet, spaced between main "T" at 600mm c/c to form a grid of 600X600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixures,smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin,etc with dash fasteners,GI adjustable rods of 3mm dia with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-Charge.

Taking up of or down GI tubing and connections 15mm bore complete all as specified and directed and directed.

Taking up of or down GI tubing and connections 20mm bore complete all as specified and directed and directed.

S&F 15mm bore galvanized iron tubes medium grade with all fitting and fixed complete to walls, ceiling or laid in floor complete all as specified and directed.

S&F 20mm bore galvanized iron tubes medium grade with all fitting and fixed complete to walls, ceiling or laid in floor complete all as specified and directed.

S&F Stop valve,15 mm cast copper alloy chromium plated fancy type with long shank &cup(concealed type) with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 15mm bore iron fixed in repair complete

S&F Stop valve,20 mm cast copper alloy with long shank &cup with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 20mm bore iron fixed in repair complete

S&F 15mm angle stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed in repair .

Supply and fixing in repair Bib tap chromium plated, cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete all as specified and directed and directed. Make:- Jaquar/Cera/ESS ESS as per approved by GE.

S&F 15mm dia CP Pillar tap ,brass, fancy type chromium plated , screwed down high pressure with long screwed for 15mm bore iron pipe and fixed in repair complete all as specified and directed & directed. Make:- Jaquar/Cera/ESS ESS as per approved by GE.

S&F in repair for Vitreous china wash hand basin, white flat, size 550 x400 mm incl brackets waste coupling and waste pipe all as specified and directed and directed by Engineer - in - Charge. Make:- Parryware/Hindware/Cera

S&F Brass CP Wash hand basin Mixture with capstan heads, chromium plated,screwd down high pressure,with lettered "hot' or 'cold' with long screwed shanks and fly-nuts, screwed for iron pipes and fixed in repair.for mixing hot &cold water screwed down for iron pipe and fixed. Make:- Parryware/Hindware/Cera

S&F Hot and cold wall mixer fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe suitable for 15mm bore pipe fixed to wall complete all as specified and directed. Make:- Parryware/Hindware/Cera

S&F in repair squatting pan WC orissa pattern size 580 x 440 mm white with integral foor rest with P or S trap incl provn of lime concrete bedding incl breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor complete all as specifed. Make:- Parryware/Hindware/Cera

S&F in repairs Vitreous china wash down water closet pan (padestal pattern), white (excluding fixing bolts,flushing cistern) incl seat cover and flushung pipe for pedestal pipe etc. Make:- Parryware/Hindware/Cera

S&F coloured vitreous china wash down one piece water closet with seat cover , hinges, Accessories set, size 625x350x730mm fitting with twin flush fitting with inlet ball valve float and handle, incl fixing bolt, with bottom and cover and mild steel chromimum plated hinging device with complete fixed in repairs all as specified and directed and directed by Engr-in-Charge. Make:- Parryware/Hindware/Cera

S & F in repair seat cover for water closet pedestal pattern all as specified and directed

S&F PVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle, 10 ltr capacity including brakets fixed in repairs. Make:- Parryware/Hindware/Cera

S& in repair PVC connection fiber, reinforced 45cm long with brass check nut and PVC washers at both ends complete fixed in repair

Supply and fixing in repair health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed and directed. Make:- Parryware/Hindware/Cera

S&F in repair Chromium plaged jet for EWC 600mm long tube superior quality all as specified and directed

S&F Soap dish stainless steel chromium plated fixed with brass screws and rawl plug complete all as specified and directed .

S&F in repair Acrylic corner set of 3 pieces as per sample approved by Engr -in-charge all as specifed and directed

S&F in repair 500 ltr UV protected, antimicrobial rotational moulded polythylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position incl 20mm for ball valve PVC high pressure, with polythene float and fly nut complete all as specified and directed. Make:- Sintex (Pure)/Sheetal/Polycon

S & F in repair 1000 ltr UV protected, antimicrobial rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) Triple layer hosted and fixed in position incl 20mm for ball valve PVC high pressure, with polythene float and fly nut complete all as specified and directed. Make:- Sintex (Pure)/Sheetal/Polycon

S&F in repair 20mm for ball valve PVC high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed. Make:-Jaquar/Cera/ESS-ESS

S&F brass chromium plated shower rose of 125mm size, with or without swivel joints including fixing to steel pipe or union in repair.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers including cantilever cast iron brackets, connecting union ,waste coupling and waste pipe over all size 915 mm x 460mm with bowl size 410 mm x 330 x 160 mm. Make:- Nirali/Jayna/Blue Star

S&F in repair vitreous china Urinal, flat back , white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass secews, pointing around urinal back in cement, including and fixing of flush pipe, grating with waste coupline, and union for discharge pipe, waste pipe ,spreader etc, size of urinal 59cm x 39 cm x 37.5 cm all as specified and directed and approved quality and directed by Engr-in-Charge. .

M&L for mild steel pipe 25 mm dia curtain road with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade as approved by GE all as specified and directed.

M&L for PVC (SWR) floor trap with grating including jointing to waste pipe fixed with solvent cement. Diameter of outlet in 75 mm) complete all as specified and directed including taking out damaged floor trap in any type and position.

Cleaning of floor trap and applying of cement around the floor trap with sealant compound for arresting the seepage at any circumstances (Kitchen, Bathroom and Toilet ) all as specified and directed and directed by Engr-in-Charge.

Demolition and braking up drain pipes AC/PVC pipe in event n.exc 150 mm dia including all fittings.

S&F for 110 mm PVC (SWR) Rain water pipes single socketed in any length with rubber ring joints fixed to walls and floors.

Ditto as per description of item no 104 above bbut 75 mm dia

PVC (SWR) bends 110 mm with access door

Ditto but 75 mm with access door

S&F for 110mm PVC (SWR) vent cowl

S&F Brass chromium plated tubular tower rail 20mm dia , D type, 60cm long between flanges in repairs

S&F in repair CP grating 125mm dia with centre hole all as specified and directed and directed by Engr-in-Charge

Repair to steel rolling shutterr gear operated type with gear box and crank handle including carefully taking down the existing shutters and replacing all damaged part / fittings and accessories etc and refixing the same shutter with new fittings on same opening and making good the floor/ wall area and match the surface complete work including greasing complete all as specified and directed and directed.

S&F in repair safety lever locks mild steel with 4 lever for rolling shutter complete all as specified and directed and directed.

S&F in repair ball bearing for rolling shutter complete all as specified and directed and directed

M&L for welding in repairs exc 2.5cm but n exc 5cm in length for thickness of metal to be welded exc 6mm but n exc 9mm complete all as specified and directed and directed.

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excludding precast concrete articles, all as specified and directed.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6 M mean radius built in CM (1:6), all as specified and directed.

Ditto as per description of item No 116 but except bricks

Dismantling of brick tiles single layer as in roof covering complete all as specified and directed

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified and directed.

M&L for PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in benching, roof padding, roof kerbs or mud stops, coping etc rounded or chamfered on edges.

M&L Painting the roof surface with a coat of hot blown paving industrial bitumen 85/25 as a bonding material in two coats one on primed surface & 2nd on APP based polymeric membrane at the rate of 1.20 kg/sqm complete all as specified and directed and directed

M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick rainforced with five layer polyster non wove fabric ( wt. Not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and directed

M&L for 40 mm thick brick tiles with 15 mm thick bedded layer of 1:6 CM laid on 2nd bitumen coated surface and joints grouted flush mortar 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified and directed .

All as per item No 123 above but except tiles

M&L Cutting out cracks to V-section in existing RCC roof slabs or terracing , cleaning out & filling solidly with a hot mixture of bitumen and clean dry sand 1:1 ( by weight) complete all as specified and directed and directed

Flush pointing in cement mortar 1:3 on brick tiles laid flat on roof and wall surfaces complete all as specified and directed and directed

Racking out joints/pointing hacking for Key, scrubbing down with water complete all as specified and directed and directed .

M&L 10mm thick cement plaster with WPC in cement mortar (1:3) on concrete roof surfaces finished even and fair, including cleaning the roof top by water etc all as specified and directed and directed by Engr in charge

Cleaning the surface and made free of dirt, foreign particle, laitance followed by grinding all all protrusion to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expiation contraction. Cutting the grooves with suitable cutter machine in V groove filled with repairs mortar/ microconcrate / general purpose grout as recommended proportionally as per recommendation of manufacture. Making of Gollas at all the corners with polymer modified mortar (1:4) cement sand with 3.5% acylic of cement weight

supply and applying high build elastomeric waterproofing coating based on pure hydrophobic polyurethane cold appliId of spray/brush applied, membrane with an elongation of 280% and tensile strength of 2.7N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88% solid content. The system includes final base preparation, epoxy primer 1:1 (Resin; harder) application with 100% water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 kg per Sqm. Application should be done with Graco sprayer by a company authorised applicator ”

M&L for repairing of R.C.C projections, chajjias, roofs, facia etc by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.C.C surfaces with cement concreat (1:1.5:3) using 12.5mm graded crushed stone aggrigates and reinforcement with welded mesh of weight exc 2 kg per sqm but n.exc 3kg/sqm (if reqd) with or without facia and finished with cement and sand motar (1:3) using coarse sand and work in patches area n.exc 5 sqm each and thickness of R.C.C member n.exc 70mm incl necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed and directed by Engr-in-charge.

M&L for cement concrete type E-2 1:5:10 (using 40mm graded brick aggregate ) as in sunken flooring/sub base fdn complete all as specified and directed and directed

Material and labour for cleaning of cracks & filling of cracks with SIKA latex SBR 100 putty/ Dr fixit 302 SBR latex/ Perma latex SBR/ FORSROC Nitabond SBR latex/ Asian Paints latex as required. Apply one coat of Acrylic modified cementitious coating of SIKA top Seal-107/Brush Bond FOSROC/ Dr Fixit/ STP/ CICO as per manufacturers instructions. Apply glass fabric sheet of SIKA fab 1/ FOROC/ Dr Fixit/ STP while the first coat is wet. Providing and applying a protection screed of 50mm thick in CM (1:4) mixed with Sika platocretere over the applied water proofing coating on horizontal surface. All the corners and joints should be pretreated with elastic waterproofing sealing tape with woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/ FOSROC/ Dr Fixit/ STP. Note : Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturers and approved by GE

Material and labour for 15mm thick cement screed in CM (1:3) admixed with integral water proofing compound on wall and sunken floor including PCC (1:1.5:3) (using 12.5mm thick graded aggregate) in fillet at corners shall be provided complete all as specified and directed and directed

Demolition of cement concrete in ground floors and paving n. exc 15 cm thickness (below or above the ground level) all as specified and directed.

M&L for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75mm thick as in sub base of flooring.

M&L for 50mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth with using extra cement all as specified and directed

M&L for 40mm thick PCC (1:2:4) type B1 using 20mm graded aggregate as in floor topping; concrete surface finished even & smooth without using extra cement complete all as specified and directed.

S&F glass dividing strips, 38mm width 3mm thick and inserted in position to conforming to design.

M&L for 60mm thick pre-cast factory made machine pressed coloured cement concrete (M-40 design Mix) inter-locking coloured blocks /tiles ,shape and pattern as directed, and filling of joints with sand including compaction with plate vibrator before and after laying of paver blocks incl dismantling of old paver block complete all as specified and directed.

All as per Ser item No 140 above but except precast concrete interlocking paver block

M&L PCC (1;2:4) type B-1 using 20mm graded stone agregete as in sides of rounded or chamfered on edges of interlocking/ chequered tiles, bed block concrete.

SANMATI UDYOG (BID ID -3076537)

B.P CONSTRUCTION CO (BID ID -3086002)

NATIONAL BUILDERS (BID ID -3075369)