PERIODICAL SERVICES OF OH TANK/UG SUMP AND PUMP HOUSES ALONGWITH OTHER MISC B/R MAINT WORKS IN THE AREA OF AGE E/M EXT (WS) UNDER GE E/M LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

M&L for brick work with fly ash bricks as per IS 12894 -2002 straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with fly ash bricks as per IS 12894 -2002 straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 40mm thick PCC type B-1 1:2:4 ( 20mm graded agg) finished even and smooth with using extra complete all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges, complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed.

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished the surface even and smooth without using extra cement mixed with WPC as per manufacturer instructions but not less than @ 3% by weight of cement complete all as specified and directed. (Note : Integral WPC shall be measured and paid seprately)

M&L for 15mm thick rendering on brick work or concrete surfaces in CM 1:6 and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 and finished the surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral WPC conforming to IS sepcification complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coat of oil bound distemper over one coat of oil base primer all as specified on walls surface including a thin layer wall care putty complete all as specified and directed.

M&L applying two coats of Apex ( Asian Paint) / Weather coat (Berger) over newly plastered surface including preparation of wall surface complete all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed.

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 15mm thick screed in CM 1:6 complete all as specified and directed.

M&L Vitrified ceramic tiles 10mm thick (square/ractangular) Coloured polished tiles, area of each tile exc 0.16 sqm but n.exc 0.38 sq m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match over and including 15 mm thick screeding in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 10mm thick screed in CM 1:3 complete all as specified and directed.

Dismantling stone slab and tiles of any description or and thickness in floors, aprons etc laid dry or laid bedded and pointed in any mortar complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over and including rendering 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick in cement mortor 1:4 complete all as specified and directed.

M&L for 75mm thick plain cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in floor or sub base, finishing the surface even and rough complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block ISI Marked of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L Chequered cement concrete coloured tiles 30 cmx30cmx20 mm thick with coloured cement and pigment , set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in CM 1:6 as in floors complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L Reinforced Cement concrete 1:2:4 Type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls and in shelves etc and the like complete all as specified and directed.

M&L Form work to soffits of suspended slabs, floor slabs, landings and similar work; not exceeding 200 mm thick fair finished flat complete all as specified and directed.

S&F TMT reinforcement bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed.

Demolition of existing roof treatment of any type, complete all as specified and directed.

M&L 15mm thick screed plaster on RCC slab CM 1:4 with using water proofing compound as per manufacturer instructions but not less than @ 3% by weight of cement complete all as specified and directed. (Note :- WPC to be measured and paid separately)

Water proofing treatment on roof surfaces to the following specification:- (a) Applying oil bound bitumen primer @ 0.40 lit / Sqm of density 0.87 - 0.89 Kg/lit of 25º C after preparation of the surfaces. (b) Supply and laying 3mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10cm and 15cm end lap weighing not less than 3.5 kg/sqm.

M&L for applying one coat of aluminium paint including preparation of any surfaces and primer, complete all as specified and directed.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar in 1:6 and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, complete all as specified and directed.

Taking down chowkats or frame , not exceeding 1.5 sqm in each shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame , exceeding 1.5 but n exc 4 Sqm in each shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

S&F well seasoned 2nd class hard wood plan, solid, straight chowkat and frames, wrought framed, rebate on the solid rounded or chamfered, put together with glue pinned at joint complete all as specified and directed.

S&F Pressed steel frames of size 125x60mm (PBI sheet 1.25 mm thick) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. supplied and fixed complete all as specified and directed.

S&F Pressed steel frames of size 105x60mm (PBI sheet 1.25 mm thick) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., supplied and fixed complete all as specified and directed.

S&F for Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in embedding holdfast, bed block, cills, filling of pressed steel frame etc including necessary formwork complete all as specified and directed.

M&L for preparing surfaces of wood and woodbased marterial, steel and iron works new or old of any description and girth treating ends of post back of chowkats etc, area tarred exc 0.1 sqm but n exc 0.5 sqm each with tar or coal tar black paint complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 30 mm thick second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc , divided in to square with plain chamferef or rounded mitred and rebate sash bars, any numbers edges of framing plain, chamfered or rounded, size / section of members of shutters shall be as specified in SSR Part I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 30 mm thick second class hardwood glazed shutters as in windows/vertilators open rebateed and prepared to received mitred aand secured sash bars any numbers edges of fsdraming plain chamfered of rounded in SSR Part I Section 8 caluse 8.24 (b) complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise desceribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F for anodised aluminium frame for doors, windows, ventilators, partition section not less than 2mm thick with one or more rebates including joining cleat for fixing etc. including taking down complete all as specified and directed.

S&F for anodised aluminium work for doors, windows any type sliding or fixed, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including taking down complete as per architectural drawings complete all as specified and directed. (Note :- Thickness of aluminium section not less than 2mm thick)

S&F in repairs aluminium anodized grill with suitable aluminium anodized frame of F/H section with suitable fixing screws/attachment etc complete all as per M/S Deco Grill Design No DG -102 , 7.5mm size grill i.e. made out of 75mm thick aluminium plate all as per manufacturer's specifications, complete all as specified and directed.

S&F for PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F for factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F 50 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 75 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 100 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs, 300 mm long, mild steel, rat tail rod pattern springs including roller and roller plates complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise desceribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or bricks round, glazed with putty or fixed with bedds complete all as specified and directed.

S&F 3 mm thick sheet glass , ordinary quality and glzing with oil putty/timber bedds in square n. exc. 0.50 sqm in each pane complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane, complete all as specified and directed.

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections of 20 mm bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking down existing PVC water tank capacity exc 250 & n.exc 500 ltr and S&F Rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed (Minimum weight 20mm-210gms) complete all as specified and directed.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair CP Angle stop cock (one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs PTMT( Polytetra Methyllene Terephthalate ) Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified and directed.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified and directed.

S&F in repairs VC WHITE Squatting pan ,'Orissa' pattern size 580x440mm with integral footrests water closet) with 'P' or 'S' trap front or back inlet complete including lime concrete for bedding, connection to drain pipe and to flushing pipe, anti syphon, complete all as specified and directed.

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. embedded in red lead cement, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe), complete all as specified and directed.

Taking down pipes (any sizes) incl all fittings, complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall, complete all as specified and directed.

Dismantling post or struts (wood/steel or RCC) any section incl taking out embedded portion and making good distrubed on normal ground in concrete, brick works masonary complete all as specified and directed.

S&F for angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing ire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S&F for M S work as framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc complete all as specified and directed.

M&L for preparing new steel steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs complete all as specified and directed.

S&F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed. (Note :- Each line wire to be measured)

Restraining/resecuring including making good staplesgalvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed. (Note: Each line wire to be measured.)

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

All as per item No. 103 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed.

All as per item No 105 above but two coats

M&L for complete removal existing treatment and distempering walls with Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade (upto 25 mtrs height) complete all as specified and directed.

M&L applying one coats of Apex ( Asian Paint) / Weather coat (Berger) over old painted surface including preparation of wall surface complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed.

All as per item No 109 above but two coats

All as per item No 109 above but on ceiling.

Complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a thin layer of Birla or JK white wall care putty on old plastered surface including washing floors, cleaning glass, joinery,electrical fittings, wiring etc of drops and splashes complete all as specified and directed.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint (upto 25 mtrs height) complete all as specified and directed.

M&L for writing letters or figures (Block, Roman Italic or Indian) n exc 30 cm high with a thick coat of synthetic enamel paint without showing signs of brushes mark complete all as specified and directed.

M&L for stops.commas, short lines, dashes, hyphens, brackets etc complete all as specified and directed.

Removing debris (old concrete) exc. 1.50 Km but n exc. 15 Km and depositing where complete all as specified and directed.

M/S SWATI CONSTRUCTION

Abode Artisan Enterprises

M/s Sachkhand Traders

NEW BHARAT ENGINEERING AND CONSTRUCTION CO