Providing and Fixing of Canopy , Play Station and Open Gym in various Parks NIT -86 Constituency. (Recall)

1. FRP Moulded Canopy (Gazebo Hex. Shape) Double Finishing sheet in 18` Dia i) 6 No. Ornamental Design FRP Molded Pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 20mm drilled in the base with hold fasts and having B class vertical M.S. pipe of size 88 mm and height 2890mm, the central M.S. pipe holds FRP Molded taj 6no of size 260 x 260 x 210mm high suitably mounted at appropriate height complete as per design. Complete pillar suitably grinded and subsequently spray painted with two coats of P.0 Paints [Epoxy primer (Interseal 670 HS) and PU Finish (Interthane 990) paints (Protective coating division)] item with GST, Transportation, Installation with C.C and amp: labor at site.) in required shade. ii)12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two M.S. pillars as per the design. The spandrel (L-Bracket) having length 420mm and height 400mm the frieze (Top Panel) height 250mm and length as per the size of the gazebo. The frieze mounted on M.S. tabular pipe frame of size 50mm x 25mm, frieze properly welded to the column pillars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with [Epoxy primer (Interseal 670 HS) and PU Finish (Interthane 990) paints (Protective coating division) item with GST, Transportation, Installation with C.C and amp: labor at site]. iii) 3 No. cast iron/frp base panel railing with frame Floral and Ornate decorative design cast iron/frp side railing panel as per design having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 50 x 25 mm. The bottom mild steel pipe having 2 nos. of hold fasts in M.S. pipe of size 40 x 40mm and length 250mm welded at the base to hold the panel in the ground. Every panel length is as per the gap between the two pillars. The complete railing panel grinded for neat surface finishes with Epoxy primer (Interseal 670 HS) and PU Finish (Interthane 990) paints (Protective coating division) item with GST, Transportation, Installation with C.C and amp: labor at site. iv) One set of top frame with Double Finishing FRP Molded Plastic roof Top frame in MS tubular pipe of size 40 x 40mm properly with FRP molded sheet of 4mm thick with top and bottom good finishing (Double finishing sheet) to make it rust proof bent to profile of size 245mm width in -Z- section on either ends fixed horizontally along the length between column pillars. Also it contain FRP Moulded Ball of 14” Dia x 2mm thick at the central top for its beautification. Each sheet properly riveted to horizontal sheets complete with Epoxy primer (Interseal 670 HS) and PU Finish (Interthane 990) paints (Protective coating division) item with GST, Transportation, Installation with C.C and amp: labor at site. The complete item is fitting at site without C.C Floor and without sitting bench at site.

Bridge Ladder: 10’L x 2’W x 6’H. Horizontal ladder is of M.S. pipe 2”, ¾” andamp: vertical ladder is of same material of 12-gauge ISI mark with Epoxy primer (Interseal 670 HS) and PU Finish (Interthane 990) paints (Protective coating division). Complete item with GST, Transportation, Installation with C.C and amp: labor at site.

Installation charges all items

Providing and fixing of Knee Chair complete in all respect as per specification KNEE CHAIR Machine Part Description of Knee chair 1. Back Seat 2. Gripper 3. Arm 4. Seat 5. Connector Pipe 6. Oscillator pipe 7. Roller 8. Mounting Plate 9. Center Pillar 10. Cap 11. Round Plate 1 12. Round Plate 2 13. Seat pipe 14. Circlip 15. Pin 1 16.Bearing 17.Metal Cap 18.Rubber Washer 19.Pin 2 20.Locating Strip KNEE CHAIR MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE 1. A circular mounting plate of diameter 233mm and thickness 8mm. 4 eye holes made on this plate at 90 degree which is P.C.D 170mm, hole diameter is 20mm, length is 39.9mm. 2. On circular mounting plate ,a center pillar is welded diameter of center pillar is 114mm and height is 294mm.A round plate 1 is welded on the upper edge of the center pillar having diameter 104mm and thickness 5mm. 3. Seat pipe is welded on the round plate 1 along with the center pillar. It have three parts long straight edge length 366mm, 240mm radius and short length of 150mm bent at an angle of 100 degree from the base. The pipe used is of diameter 60mm and thickness 4mm.Center pillar is welded 239mm apart from the long straight edge of the seat pipe. 4. Locating strips are welded on the seat pipe 154.5mm and 265.5mm from the long straight edge of the seat pipe. Strips having length 55mm, breadth 35mmand thickness 3mm.A hole is made of diameter 13mm and 15mm apart towards the center pillar to locate seat well. Similar measurements for all the strips welded. A plastic seat is fixed on the holes made with the help of Allen bolts (poly drive head). 5. Back seat is located on the short length of the seat pipe with the help of strips welded 5mm above on the center face of the seat pipe and another one is welded 82mm from the seat pipe edge. 6. Arm have five parts length1 189mm,radius 104.4mm,straight length 166.9mm,radius 74mm bent at angle 130 degree,length2 160.8mm. Arm’s length1 edge is welded 205mm from the center of the center pillar and height 318.1mm on both the faces of seat pipe. Grippers are gripped on the length2 of the arm. Grippers used are either of plastic or rubber. 7. On the edge of the long straight edge a pipe of diameter 60mm, length 65mm and thickness 4mm is welded. A pipe of diameter 60mm, length 65mm and thickness 4mm is welded on both the edges of the oscillator pipe. Round plate 2 having thickness 4mm is welded on both sides 13.5mm inwards on edges of the pipe welded on the long straight edge of seat pipe. Round plate 2 have a hole of diameter 28mm. 8. On the upper welded pipe of the oscillator pipe having two bearing fitted, first on the edge and other one is fitted 29mm inwards from the edge of the pipe. Two oscillator pipe having similar mechanism discussed above attached on both sides. A pin having diameter 28mm and length 166mm is welded with the round plates and attached throughout both pipe with the help of bearing, welded along the oscillator pipe. A circlip slot(1.5x2) is made 5mm inwards from both the edges of the pin. Cap is fixed on both the edges of the pin. 9. A round plate is welded 41mm inwards in lower edge pipe of the oscillator pipe. A pin of diameter 28mm and length 227.6mm is welded with the round plate outwards .Plastic Cap is tightly fixed inward. A roller is fitted with the pin having inner diameter 25mm.A washer having diameter 60mm and thickness 5.5mm is fixed in between the roller and the circlip to avoid wearness and maintain the gap along .A circlip slot (1.5x2) is made 6.5mm from the face of the pin and self locking metal cap is fitted on the edge to avoid displacement of the roller. Since metal cap is self locking so that it cannot be detached untill it will not be broken. 10. Short length of the seat pipe has a cap fixed on the open edge .

Providing and fixing of Double Skier complete in all respect as per specification Double skier Machine Part description of double skier • Circular mounting plate (1and2) • Center pillar 1 and 2 • Standing base rectangular pipe • Standing pads • Main pipe • Holding Arms • Connecting pipe 1 • Connecting pipe 2 • Bearing hosing pipe 1 • Bearing hosing pipe 2 • Pendulum pipe MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE 1. Two circular mounting plates of diameter 233m and thickness 8mm. 4 eye holes are made on the plate at 90 degree which is P.C.D 170mm, hole diameter is 20mm, length is 40mm. 2. On circular mounting plates a center pillar is welded of diameter of center pillar is 114mm and length is 955mm having thickness 3mm. 3. Main pipe of diameter 114mm,thickness 2.5mm and length 600mm welded on both the pillars and the distance between the pillars is 320mm. Both the edges of the main pipe are welded with connecting pipes. 4. Two connecting pipes having diameter 114mm,length 100mm and thickness 2.5mm.The midpoint of the connecting pipe is welded from both the edges with the main pipe. 5. Connecting pipe have metal plates welded of thickness 4mm, outer radius of the pipe is according to the inner radius of the pipe. A hole is made on the metal plate of diameter 28mm, welded with a rod by maintaining 87mm rod outside the plate having diameter 25mm. 6. Two bearings are fixed on the rod of the diameter 25mm having inner diameter 25mm and outer diameter 60mm with the help of a circlip groove. The distance of the first bearing is 125mm from the metallic plate welded and the distance between the two bearings is 38mm. 7. The bearing hosing pipe 1 is fixed on the both the bearings having length of 90mm, diameter of 70mm and thickness 5mm. 8. An arm pipe of diameter 32mm is welded vertically on the bearing hosing having five parts straight length 1149mm, radius 60mm tilted at 27 degree, tilted length is 120mm, radius 60mm straight length of 142mm parallel to the top of the arm pipe. 9. A pendulum pipe of diameter 50mm, thickness 2.5mm and bending radius 1516mm,length is 750mm. One edge of the pendulum pipe is welded with the bearing hosing pipe 1 and the other edge is also welded with the bearing hosing pipe 2.The bearing hosing pipe 2 have arod fixed of diameter 28mm and length is 90mm. 10. Two bearing having inner diameter 25mm and outer diameter 52mm. The distance between the bearings is 28mm and the in between diameter of rod is 26mm. After fixing the bearing the remaining rod have diameter 25mm is maintained and both the ends of the bearings are screwed with the help of nuts. 11. There are four similar rod mechanism fitted with the machine. Two attached with one connecting pipe on both of its ends. Similarly with the other connecting pipe as they are of the mirror image of each other. 12. Standing base rectangular pipe having dimensions 1600mm*60mm*30mm and wall thickness2.5mm and rubber pads are fixed on both the ends. Two u-shaped brackets are welded 600mm apart from each other ,each rod having wall thickness 3mm.Brackets height is 100mm from the top of the standing base rectangular pipe. Holes are made of 26mm from that face too and is connected with the bearing hosing pipe 2 along with the pendulum pipe. 13. Standing pads of 324mm*134mm*40mm and of wall thickness 2.5mm are welded on each edge of the standing base rectangular pipe. The distance between the two standing pipes is 972mm welded on a rectangular pipe. Plastic caps are fixed on the open edge of the each bearing hosing pipes to prevent dust

Providing and fixing of Shoulder Wheel complete in all respect as per specification SHOULDER WHEEL Machine Part Description of Shoulder Wheel 1. Mounting Plate 2. Center Pillar 3. Jointer pipe 4. U-Arm 5. Actuator 6. Wheel support 7. Wheel 8. Knob 9. Cap MACHANICAL DIMENSION AND MEASUREMENT OF MACHINE 1. A circular mounting plate of diameter 233mm and thickness 8mm. 4 holes on this plate at 90 degree which is P.C.D 170mm, hole diameter is 20mm. 2. On circular mounting plate ,a center pillar is welded diameter of center pillar is 114mm and height is 118mm. 3. Cap is fixed on the top of the center pillar with the help of groube screw. 4. 2 Jointer pipes are welded with the center pillar whose diameter is 60mm and length 107mm. 5. Jointer 1st is welded at the height 889mm and Jointer 2nd is at height 989mm. 6. U-arm band is welded on the edge of the jointer and midpoint of the band, pipe used whose diameter is 60mm and band radius 403mm having a short length extended is 90mm straight on both the edges. Band radius is bent at 180 degree. Both U-arm are welded with the jointer at an angle of 45degree from the base. 7. A dart having thickness 5mm is also welded below the Jointers which provides support to the Uarm bands. 8. Wheel is made of the pipe having diameter 32mm and it is bent at 360 degree whose outside diameter is 482mm.3 Wheel supports are welded with the inner side of the wheel. One edge of the wheel support is welded with the wheel and the other one is with actuator at the responding angle of 5 degree .There are 3 wheel supports welded adjacent to each other at angle of 120 degree. 9. Actuator is made up of pipe having diameter 60mm and length is 60mm.Actuator is coupled with the extended edge of the U-arm band with bearing and pin in between whereas the other end is fixed by the Allen (polydrive head) bolt having plastic cap fixed on the top. 10. A knob is fixed parallel to the straight short length of the U-arm on the wheel as it can swing on its own axis individually and with the wheel, both clockwise or anticlockwise direction .This knob is made up of either plastic or rubber.

Providing and fixing of Back Shaper complete in all respect as per specification BACK SHAPER MACHINE PART DESCRIPTION OF ROWER MACHINE 1. RECTANGULAR PIPE 2. BRACKET 3. PIPE-1 4. PIPE-2 5. PIPE-3 6. STOPER BAND 7. RUBBER PAD 8. ANGULAR SEAT BASE PIPE 9. FOOT RESTER JOINT 10. FOOT RESTER 11. BENDING ARMS 12. GRIPPER 13. SEAT 14. BRACKET 15. FOOT RESTER SUPPORT PIPE MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE ARE FOLLOWING 1. A rectangular base pipe having length 1010 mm breath 78 mm and height 40 mm. Three bracket are welded on the rectangular base pipe. 1ST bracket 50 mm ,2nd bracket 65 mm and 3rd bracked 760 mm from the edge of the base pipe. 2. Pipe 1 is arranged with the bracket 1 and having length 342mm and diameter 48mm. 2 bushes are welded on both edges of the pipe1, pipe 2 is also arranged with the bracket 2 and length 349mm and diameter 48mm and bushes are welded with it on both edeges. Similarly 3 brackets are also holding pipe 3having length 342mm and diameter 48mm with bushes welded on both edges. 3. Bending arm pipe welded with the bracket box on both its sides .This arm pipe haves parts, short length 91mm, radius1 121mm, angular length 517mm,radius2 96mm, extended length 140mm.The bending arm are 258mm from the base pipe towards upward. 4. Grippers are studded at the edge of last short straight pipe having material plastic or rubber. 5. Angular seat pipe having parts straight length 1119mm, and angular length 363mm,and having dimensions breadth 78m, above length bracket 1st is welded 88mm form the straight edge of the angular seat base pipe whereas bracket 2nd is welded 528mm from the straight edge of the angular seat base pipe. Each bracket is welded opposite to it. 6. Seat are fixed on the angular seat base pipe with the help of steel Allen bolt (polydrive head). It is of either plastic or metal. 7. Stopper band is also welded with the angular base pipe 334mm from the straight edge of base pipe. Rubber pad is tightened at the ending edge of the stopper band and to avoid shock. 8. Centre of the foot rest pipe is welded with the straight edge of the angular seat base pipe equally. And foot rester is also welded angularly on the foot rester pipe .The diameter of the foot rester pipe 32mm and length 160mm. 9. Foot rester jointers are welded on the foot rester pipe having length 315mm breadth60mmon the either sides of the rester joints, apart 432mm from the edges of the foot rester pipe .Foot rester is joined on the foot rester pipe with the help of polydrive head Allen bolt. 10. Pipe 1 is connected with the bracket 1st of the rectangular base pipe and angular seat base pipe, pipe 2 is connected with the bracket 2nd of the rectangular base pipe and angular seat base pipe, pipe 3 is connected with the bracket 3rd of the rectangular base pipe and another bracket welded on the edge of the (straight) of the angular seat base pipe ,Bushes of all the pipes are joined with the brackets having bearing and pin in between , tightened with Allen bolt polydrive head bolt having plastic caps on the ends. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Abs Shaper complete in all respect as per specification MACHINE PART DESCRIPTION OF THE ABBS SHAPE a. Circular mounting plate b. Center pillar c. Main pipe d. Square mounting plate e. Frame base pipe f. Frame supporter g. frame h. foot rest i. bending support pipe j. PVC Pad k. Cap 1. A circular mounting plate which has diameter 233mm and thickness 8mm. also has 4 holes at 90 degrees which PCD is 170mm. the diameter of the hole is 20mm 2. In this circular mounting plate , a center pillar is welded. Diameter of the center pillar is 114mm and the height is 568mm. 3. Cap is fixed on the top of the center pillar with rivets. 4. Two main pipes are welded opposite to each other with the center pillar having length 266mm, height from the bottom edge is 174mm and diameter 48mm. 5. Two square mounting plates are welded on the main pipes, apart from the edges of the mounting main pipes 91mm. these plates are of length 190mm, breath 150mm and thickness 5mm 6. A frame base pipe is welded with the square mounting plate at a distance of 14mm from the one of the edge of base pipe having 2 parts, first length straight pipe 108mm and radius 119mm. therefore we have four base pipes welded on the 2 square mounting plate (2x2). Towards the welding, the distance between the two base pipes is 218mm. 7. A foot rest pipe is welded on the radial edge of the 2 base pipes of one square mounting plate. Rest pipes are extended equally from the center. 8. A frame support is welded on the frame base pipe having length 385 mm and diameter 38mm, from the straight edge of the frame base pipe is 84mm. this support pipes are welded on 4 base pipes. 9. A curved frame having a curved radius 2384mm and fliet radius 74mm is welded with the straight edge of the frame base pipe and 2nd side is with the foot rest pipe. Fliet radius is on the four corners of the curved frame. The pipe used to make the curved frame have diameter 32mm. 10. A PVC pad is mounted on the curved frame having same dimensions as of the curved frame, with the help of the mushroom head screws (steel). 11. Bending support is welded on the either side of the center pillar having 3 parts short length 34mm radius 150mm and long straight length 179mm. the bending support is welded 322mm from the center pillar on the main pipe whereas other edge (towards short length) welded with center pillar. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Shoulder Shaper complete in all respect as per specification THE SHOULDER SHAPER MACHINE PARTS DESCRIPTION OF SHOULDER SHAPPER • Mounting plate • Centre pillar • 2 hinge holding pipe • 2 bending pipe • Cap • 2 u shapped pipes • Handles • 2 straight pipe(no.-1) • Straight pipe (no-2) • Straight pipe (no-3) • Seat base pipe • Seat bending pipe • Seat • Back seat • Hinge box • Bracket holder 1. A circular mounting plate of diameter 233mm and thickness 8mm. there are 4 holes on this plate at 90 degrees which is P.C.D. 17mm, hole diameter is 20mm. 2. On circular mounting plate a centre pillar is welded. Diameter of the centre pillar is 119mm and height is 1838mm. 3. Cap is fixed on the top of the pillar with rivets. 4. At 1528 mm vertical distance – 2 hinges holding pipes are welded in opposite directions. Hinge holding pipes have clear hole for screw at 177mm distance. 5. Bending pipes are welded to the Hinge holding pipes and the centre pillar to provide mechanical strength to the hinge holding pipe. 6. Hinge box is fitted to the hinge holding pipes with a steel screw and bush. Hinge Box has a clear hole at the base. 7. U shaped pipes are welded at the upper part of the hinge box. 8. At the opening end of the U shaped pipe, handles are fitted with steel screw. 9. Straight pipe no.1 is fitted to the hinge box at the base with Pin bearing. 10. Lower end of the straight pipe no.1 is fitted to straight pipe with a pin bearing. 11. Straight pipe no.2 and no.3 are joined to the centre pillar and seat base pipe one over the other respectively with a gap of 490mm, through bracket jointers, which are welded to the centre pillar and seat base pipe also. 12. Seat base pipe is connected with straight pipe no.2 and no.3 with pin bearings. 13. Over seat base pipe a seat bending pipe is welded. 14. Seat and back seat are fitted on the seat bending pipe with Pin bearing. These seats may be of plastic or steel made. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Parallel Bars complete in all respect as per specification PARALLEL BARS Machine Part Description of Parallel Bars 1. Cap 2. Stopper pipe 3. Bar 4. Center Pillar 5. Mounting Plate 6. Bolt Cap PARALLEL BARS MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE CHANICAL 1. A circular mounting plate of diameter 233mm and thickness 8mm. plate at 90 degree which is P.C.D 170mm, hole diameter is 20mm, length is 39.9mm. 2. On circular mounting plate , a center pillar is welded diameter of center pillar is 114mm and height is 1537.5mm. 3. Cap is fixed on the top of the center pillar having diameter 120mm,height 69mm. 4. Two holes are made on the front face of the center pillar. One is made 383mm vertically from the mounting plate and other is made 443mm from the mounting plate. Other two holes are made similarly but on the either perpendicular face of the center pillar ,one is 1138mm vertically from the mounting plate and other hole is made 1363mm vertically above from the mounting plate. 5. Bar having diameter 38mm, thickness 4mm is welded with the stopper pipe whose diameter is 127mm , length is 350mm and thickness is 6.5mm by initial edge 100mm downwards , bar pipe is straight 126.5mm and then radius 123.3mm bent at an angle of 90degree horizontally outwards further straight length 700mm, there comes a radius of 119mm bent at angle of 52 degree downwards further extends a straight length 1000mm then bend towards the center pillar with the help of radius 120mm and the remaining straight length 106mm is welded with the stopper strip. 6. Two bars are welded, since one edge of the bar is welded with the stopper pipe 25mm from the upper edge of the stopper pipe and other is welded with the stopper strip simitrically. The distance between the two bars is 542mm inwards. 7. Another two bars are welded, since one center edge of the bar is welded 249.5mm from the upper edge of the stopper pipe and other is welded with the stopper strip at 175mm downwards from the stopper strip. 8. Stopper strip plate have two holes linearly made on either side from the center, hole diameter 15mm.Holes are concentric to the holes of the center pillar and stopper strip plate is fixed with the help of Allen bolt(poly drive head) tightened throughout on both sides. 9. At the height of 1088mm fromthe mounting plate, stopper pipe is slidefit fixed. Holes are made concentric to the holes made on the center pillar, one at the height 1138mm and other 1363mm from the mounting plate. Stopper pipe is fixed with the help of Allen bolt (poly drive head) tightened throughout on both sides. All bolts are covered with the help of plastic caps.