REPAIR WOODEN/ STEEL JOINERY IN MD/ OTM ACCN, REPAIR TO FLOORING, ROOFING, JOINERY, CEILING AND OTHER ALLIED WKS INCL SANITARY FITTINGS AND PERIODICAL SERVICES AND CERTAIN B/R REPAIR WORKS AT HAFT CHINAR UNDER GE 970 EWS

Amount

M&L for preparation of NEW surfaces of steel any description over 10 cm width or girth by scrubbing down, removing loose dirt or dust and applying two coats of synthetic enamel paint over prepared old surfaces of steel complete all as specified.

M&L for preparation of NEW wooden surfaces of any description not other wise decribed over 10 cm width or girth by scrubbing down, removing loose dirt or dust and applying two coats of synthetic enamel paint over prepared old wooden surfaces complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 15mm cement screed bed in CM (1:4) complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) as in skirting etc cut from tiles exc 0.11 but not exc 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick rendering in CM (1:4) complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.18 but not exc 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 15mm cement screed bed in CM (1:4) complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) as in skirting cut from tiles of size exc 0.18 but not exc 0.38 Sqm etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick rendering in CM (1:4) complete all as specified.

M&L for glazed coloured ceramic tiles in vertical surfaces such as skirting /dados and riser to steps area of tiles 450x300x7mm thick set and jointed and pointing in white or coloured cement to match over 10 mm thick plaster in CM 1:4 complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M & L for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate complete all as specified and as directed by the Engineer-in-Charge

M&L for providing cement concrete 1:2:4 Type B0 using 12.5 mm graded aggregate as in lintels upto 1.5m clear span,cills,steps; ceismic and other similar bands, plinth, string, lacing cources, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like incl weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by the Engr-in-Charge.

M&L johnson endura paving coloured tiles of technocommercial equivalent of size 300mmx300mmx10mm set and jointed in neat cement slurry pointed with white or coloured cement laid over and incl 15mm thick screed bed built in CM (1:4) after demolition old floor hearth or wall tiling complete all as specified & directed

M & L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) over and incl 20 mm thick screed bedding in CM 1:3, including pointing in white :cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and as directed.

S & F 605mm x 605mm anodised aluminium snap grid frame work for false ceiling, complete all as specified and as directed.

S & F for Hangers 6mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastener 12.5mm dia 40mm long, complete all as specified and as directed.

M & L for providing and fixing 12mm thick gypsum board in ceiling fixed with screw as per manufacturers instructions, complete all as specified and as directed.

M & L for 12mm thick medium density fibre board, exterior grade, fixed to timber framework with screws, complete all as specified and as directed.

Dismantling timber in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (Framed work), complete all as specified and as directed.

M & L for IInd class soft-wood clean sawn plain fillets, square, rectangular or triangular in section, and secured with nails or brads, sectional area exc 6 sq.cm and not exc 13 sq.cm , complete all as specified and as directed.

M & L for 4mm thick (3 ply) plywood, grade BWR, type BB, fixed with screws to timber frame work , complete all as specified and as directed.

S & F hollow PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on as per specifications and drawing complete all as specified and as directed by the Engineer-in-Charge

Taking down shutters of any description n exc 1 sq. m each , complete all as specified and as directed.

Taking down shutters of any description exc 1 sq. m and not exc 2 sq. m each , complete all as specified and as directed.

Refixing in same opening shutters of any description exc 1 sq. m and not exc 2 sq. m each , complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each , complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each, complete all as specified and as directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, one shop coat of zinc chromate primer paint (including reparation of surface) at Contractor’s workshop before fabricationquality conforming to GDE Fe 290, Gde E-165 , complete all as specified and as directed.

S & F 30mm thick, 2nd class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with comercial face veneers; fitted to chowkats complete all as specified and as directed by the Engineer-in-Charge

S & F 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); fitted to chowkats complete all as specified and as directed by the Engineer-in-Charge

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed.

S & F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed.

M&L for ACP board for fixing in aluminium partition and doors complete all as specified and as directed.

M & L for sheet glass 3.0mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq m in each pane, complete all as specified and as directed.

M & L for hacking out old broken glass exceeding 1.5 sq m (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads , complete all as specified and as directed.

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified and as directed.

S&F in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staple complete all as specified

S & F 150mm aluminium handles, cast type, anodised , complete all as specified and as directed.

S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed , complete all as specified and as directed.

Supply and fixing for ISI marked 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter, complete all as specified and as directed.

S & F butt hinges 100mm size, type B-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, complete all as specified and as directed.

M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete incl demolition all as specified and as directed by the Engineer-in-Charge

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with decorative brackets & finials at the end etc complete all as specified.

Supply and fixing for ISI Marked 300mm long mild steel ordinary rat tail rod pattern springs for doors including roller and roller plate, complete all as specified and as directed.

Taking down cement plaster or brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

M&L 15 mm thick cement plaster on fair faces of bricks or concrete walls in CM 1:6 finished even and smooth with out using extra cement on brick work or concrete surfaces, complete all as specified and directed.

M&L 15 mm thick cement plaster on fair faces of bricks or concrete walls in CM 1:4 finished even and smooth with out using extra cement on brick work or concrete surfaces, complete all as specified and directed.

M&L for preparation of new/ old plastered surfaces of wall and applying two coats of oil bound distemper using painting roller over one coat of chalk whitening , complete all as specified and directed.

M & L for two coats of wall care putty (2mm thick)on old/new wall surface, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resisitant primer , complete all as specified and directed.

M&L for preparation of old plastered /unplastered surface of brick/concrete wall and applying two coats of oil bound distemper over recently prepared old painted surfaces of wall, complete all as specified and directed.

M&L for preparation of existing plastered/ unplastered surface of brick/concrete wall and applying one coat of cement based paint, complete all as specified and directed.

M & L for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20mm thick screed bed in cm 1:3 , complete all as specified and directed.

M&L Lagging to pipe of internal dia 15mm pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum Extra over if provided with chicken mesh wire netting 25 gauge, 20mm mesh conforming to IS 9842 complete all as specified and as directed .

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S & F for Pre-painted galvalume aluminum zinc coating GI based corrugated (sinusoidal pattern) steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as in ridge,eaves boards, hips, velly gutter drip and straight flushing of reuired machine moulded shape and size , complete all as specified and directed.

M&L for 25mm thick PCC type B1 1:2:4 (using 20mm graded aggregate as in sub base to floor, complete all as specified and directed.

S&F in repair 15 mm dia PVC connections, 600 mm long with PTMT nuts of suitable size at two end complete all as specified and directed .

M & L for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors including taking down existing tubing, complete all as specified and directed.

M & L for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors including taking down existing tubing, complete all as specified and directed.

S&F bib taps 15mm dia fancy type brass Chromium Plated with long body screwed down for iron pipe and fixed Iin repairs, complete all as specified and directed.

S & F of ISI marked fancy type Pillar Tap FIXED IN REPAIR of 15mm bore dia, chromium plated, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repair single/multi PVC (SWR) floor trap 75mm to 110mm dia, palin with grating including joining to waster pipe, fixed in cement concrete type B-1 (1:2:4) using 20mm graded broken stone aggregate, complete all as specified and directed.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges , complete all as specified and directed.

S&F in repair for 15 mm dia stop valves fancy type ,chromium plated screwed down high pressure with crutch or butterfly handle, complete all as specified and directed.

S&F in repair vitrious china white wash hand basin flat back white in colour ISI marked of size 550mm x 400mm with chromium plated waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 type , complete all as specified and directed.

S&F in repairs viterous china squatting pan Orrisa pattern size 580 x 440mm white with "P" and "S" trap front or back inlet etc including connectipon to trap and to flishing to pipe , anti syphonage pipe etc incl provisioning of lime concrete, complete all as specified and directed.

S&F in repairs 10 ltr PVC valveless syphonic action type flushing cistern with brackets flush pipe etc complete including inlet ball valve float and handle including brackets of approved make including all connections & flush pipes for WC , complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan ( pedestal pattern) white including connection to out going pipe and to flushing pipe and antysyphonic pipe etc including seat cover , complete all as specified and directed.

S&F for Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F for stainless steel sink with draining board made of stainless steel 1 mm thick sheet for kitchen with waste coupling waste pipe , washer and including all necessary item including fixing to brackets and connected union to pipe complete of overall size 915x460 mm with bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in rep plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device , complete all as specified and directed.

S&F for 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc, complete all as specified and directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including dismantling of existing pipes, complete all as specified and directed.

S & F 110mm bore PVC (SWR) bends of any radius,, complete all as specified and directed.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including dismantling of existing pipes , complete all as specified and directed.

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

Dismantling wrought iron or mild steel work (used in framework for stageing of water tank) of any description not otherwise provided for complete all as specified and directed.

S & F rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., quality 'A' conforming to Fe 410-S Gde E-250 including one shop coat of zinc chromate primer complete all as specified and as directed .

S&F rotational moulded polythene water storage tank 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I with and including dismantling existing water tank and including 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule & nipple suitable for HDPE water tank (Min weight 15mm-38 gms/20mm-45gms/25mm-65gms) complete all as specified and directed

S&F rotational moulded polythene water storage tank 1000 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I with and including dismantling existing water tank and including 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule & nipple suitable for HDPE water tank (Min weight 15mm-38 gms/20mm-45gms/25mm-65gms) complete all as specified and directed

M&L for rendering cement plaster 5 mm thick in cement mortar 1:3 on fair faces of concrete in ceiling, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

Preparation of new plastered or un-plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of old decorated plastered surfaces of walls and applying two coats of cement based paint complete all as specified and directed.

Preparation of old plastered or un-plastered surfaces of wall and applying two coats of white/ clour wash on wall complete all as specified and as directed.

Preparation of old decorated surfaces of wall and applying one coat of oil bound distemper complete all as specified and as directed.

Preparation of old painted steel surfaces of any description not otherwise described exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

Preparation of old wooden or wooden based surfaces exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Supply only integral water proofing compound , complete all as specified and directed.

M & L for complete removal of existing treatment on wall/roof projection incl facia, cornices etc by scraping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, paint etc by skilled labour with mechanical sander having RPM of 1500-2700 rpm, with internal dust extraction system for clean environment, and preparation of old plasterd/scraped surfaces of wall/ceiling by cracks by external wall putty/crack fill paste and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm to 2mm over the prepared wall/ceiling surfaces, one or more coats and grinding the puttied surface with mechanical grinder for make the surface even and smooth for recieving primer and applying two or more coats iof 100% Premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resisitance exterior paint of required shade (Company depot Tinted) with silicon additives & color stay technology, Excellent dirt pickup resistance @ 1.79 litre/10 sqm diluted with water as per manufacturers instructions over and including priming coat of exterior primer applied @ 0.9 litre (Undiluted)/ 10 sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:- Paint using Airless spray technology with max working pressure of 3300 PSI and capable of single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed.

M & L for preparation of newely plasterd surfaces on wall/roof projection incl facia, cornices etc and applying exterior water proof wall care putty @ 1 Kg(Undiluted) per sqm mtr. of thickness 1mm to 2mm over the plasterd wall/ceiling surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium arylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistace, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/ 10 sqm diluted with water as per manufacturers instructions over and incl primer coat of exterior primer applied @ 0.9 litre (Undiluted) / 10 sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:- Paint to be applying with using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed.

Note for Sl item No 93 and 94:- The work for periodical services shall include the following and the rates quoted by the bidders shall include the same:- (a) The work pertaining to periodical services shall be executed by the contractor as per MOU from authorised applicator through manufacture of the materials like Exterior Emulsion paint putty etc after approval by the GE. (b) The contractor shall upload with the documents under cover I "Memoradum of understanding" (MOU) with at least one of the manufacturers mentioned in the contract, failing which the bid shall be laible to be rejected. (c) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures. (d) Removing of Nails, making good holes, cracks etc. (e) Work in patches and in narrow/widths, bands, cornices, pilasters etc and cutting in edge of line where necessary. (f) Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes. (g) Washing floors, cleaning glass, joinery, electric fitting, wiring etc Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-Charge. (h) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work. (j) The work shall be carried out up to 4th storey.(k) incl.removal of vegetation on walls incl roots on wall surfaces.

Notes :- The amount of credit schedule against Schedule 'A' Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/s Bhat & Co (BID ID -3466017)

M/s Nasir Rasool Dar (BID ID -3466000)

M/S Sultan Enterprises (BID ID -3466083)