AS-16-95 Balance work of Construction of road from Tamulipara to MPK Road

Amount

Clearing and grubbing of Road land including up rooting rank vegetation grass, bush, shrubs saplings and trees of girth upto 300mm removal of stumps of trees cut earlier and disposal of unseviceable materials & stacking of serviceable material to be used or auctioned, upto a lead of 1000m including removal & disposal of top organic soil not exceeding 150mm in thickness as per Technical Specifications Clause 201. (I) By Manual Means- (a) In area of non thormy jungle

Cutting of trees, including cutting of trunks, branches and removal of stumps & roots, refilling, compaction of backfilling and stacking of serviceable material by manual means with all lifts as per Technical Specification Clause 201. (i) Girth above 300 mm to 600 mm

Cutting of trees, including cutting of trunks, branches and removal of stumps & roots, refilling, compaction of backfilling and stacking of serviceable material by manual means with all lifts as per Technical Specification Clause 201. (iI) Girth above 600 mm to 900 mm

Construction of embankment with material obtained from borrow pits,Construction of embankment with approved materials obtained from borrow pits with a lift up to 1.5m, transporating to site, spreading, grading to required slope and compacting to meet required of Tables 300.1 and 300.2 with a lead upto 1000m as per technical specification clause 301.5. (a) Private land

Construction of sub-grade and earthen shoulders Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of Table 300.2 with lead upto 1000m as per technical specification clause 303.1. (a) Private land

Construction of Granular sub-base (A) By mix in Place Method, Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (II) For Grading Material (Gr - II )

Water Bound Mecadam Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. Using Stone Screening: 3) Grading-III (A) By manual means

Prime-Coat (i) Low porosity Providing and applying primmer coat with bitumin emultion (SS-1) on prepared surcafe of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical Clause 502.

Tack-coat (III) Providing and applying tack coat with bitumin emultion (RS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface tresated with primer & cleaned with hydraulic broom as per technical specification clause 503.

20mm thick open graded Premix carpet using bituminous (penetration grade/ modified bitumen) Binder Providing , laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2 mm to 5.6mm aggregate eithe rusing penetration grade bitumen or emultion to required line, grade and level to surfe as wearing course on a previously prepared base, including mixing in a suitable plan, laying and rolling with a three wheeler 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical specification clause. Case-II By Mechanical Means (i) Bitumen (S-90)

Seal-Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause B) By mechanical means. Case II Type-B (i) Bitumen (S-90)

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801 (ii) 60cm equilateral triangle

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801 (iii) 60cm circular

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703 (ii)Ordinary Kilometer Stone (precast)

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703 (iii) 200 m Stone (precast)

Providing and Fixing 'Logo' of PMGSY Project Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing. Three MS plates of 1.6mm thick, top and middle plate will be welded with MS flat iron 25mm x 5mm x size on back on edge. The lower plate will be welded with MS angle iron 25mm x 25mm x 5mm. The anfle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The topmost dimond plate will be welded to middle plate by 47mm X 47mm of 12 SWG steel plate tube. All MS will be stove enameled on both sides. Lettering and printing arrows, borders etc. will be painted with ready mixed synthetic emnamel paint of superior quality in required shade and colour. All sections of framed posts and steel tuube will be painted and two coats of epoxypaint as per specification clause 1701 and Annexure 1700.1

Providing and fixing of typical Citizens Information Board with Logo as per MORD specifications and drawing. Two nos. 1.6mm thick MS sheet duly welded with 5mm thick steel plate on back on edges. The 4 nos. steel plate will be welded horizontally with 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. The 2 nos. steel plate will be welded vertically to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly welded to vertical tubes. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloue. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Construction of RCC guide posts of 250 mm dia M15 grade cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC posts not to exceed 1 in 500 as per drawing and Technical Specification Clause 1608.2

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. (a) Upto 600mm dia

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. (C) above 900 mm dia Hume pipe

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of brick masonry including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 metres as per technical specification clause 202 (B) Cement mortar

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.(I) In ordinary soil

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawings & Technical Specification Clause 1109. (A)(I) Nominal mix(hand mixing)

Bedding of pipe (ii) Type B(First Class) Bedding Laying (First Class) bedding on well compacted sand moorum as per Clause 1105(ii) (i) Sand Filling

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. II. In 1:4 cement mortar

Plastering with cement mortar (1:4), 15mm thick on brickwork in substructure as per Techical specification clauses 613, 614 &1204

Routine Maintenance for 1st Year (Enter the exact value (28108.00) mentioned in estimated rate)

Routine Maintenance for 2nd Year (Enter the exact value (32202.00) mentioned in estimated rate)

Routine Maintenance for 3 rd Year (Enter the exact value (129158.00) mentioned in estimated rate)

Routine Maintenance for 4th Year (Enter the exact value (161590.00) mentioned in estimated rate)

Routine Maintenance for 5th Year (Enter the exact value (230941.00) mentioned in estimated rate)