REPAIRS TO STONE JAFRI WALL, PAVING TILES, INTER LOCKING PAVER BLOCKS, POINTING FALSE CEILING, POLISHING, SS RAILING AND B/R MISC ITEMS AT GRAND STAND AT 3 AFRU, CHANDAN UNDER GE (AF) JAISALMER

Amount

Dismantling wall and ceiling boards ( fibre, pulp, insulation etc or insulation boards/ slabs/ blankets any thickness including cover filletts.

S &F Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long (removing old hangers) complete all as specified

M & L for 6 to 9mm thick 595 x 595 mm eco board classic as in false ceiling complete all as specified and directed.

M&L Anodised aluminium snap grid frame work for false ceiling all as specified

M&L preparation of old Stainless railing in any pattern surfaces of any description washing of complete prepared railing with suitable liquid/powder Chemical to match the natural stainless steel colour of extg surfaces including welding, grinding, buffing, polishing all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, S & F buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including dismantling of extg railing in any shape and in any material complete all as spd and dir.

M & L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths)as in other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, complete

M&L for preparation of new steel surface of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of primer complete all as specified.

M&L for preparation of old painted wooden surface or wood based materials of any description, not otherwise described, over 10 cms widths or girth and applying one coat of synthetic enamel paint complete all as specified any colour as approved by GE

Description all as per Ser item No above but on steel surfaces.

S & F in repair Wall paper 3D pattern primum/fabric quality fixed in VVIP guest room etc fixed with chemical as manufacture instruction complete all as spd and dir by

Taking up or down steel water tubing 15mm bore and connections, including cleaning for refixing or removal to store

S & F GI tubing medium grade, with all fitting and fixed complete to walls and ceilings or laid in floor complete of size 15mm bore.

Taking up or down steel tubing 20mm bore and connections, including cleaning for refixing or removal to store

S & F GI tubing medium grade, with all fitting and fixed complete to walls and ceilings or laid in floor complete of size 20mm bore.

S & F Rotational moulded polyethylene water storage tanks capacity of 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specifiehoisted and fixed in position all as specified incl Dismantling water tanks and removing to store.

S & F Rotational moulded polyethylene water storage tanks capacity of 1000 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specifiehoisted and fixed in position all as specified incl Dismantling water tanks and removing to store.

S&F( Fixed in repair) bib taps, cast copper alloy, chromium plated,fency type ,long boady screwed for iron pipe15mm bore, FIXED IN REPAIRS complete all as specified of cat No CON-107 KN of Jaguar or equilent.

S&F( Fixed in repair) angle stop valves , cast copper alloy chromium plated screwed down , high pressure, crutchor butterfly handle screwed both ends or iron pipe or for unions suitable for 15mm bore tubes, FIXED IN REPAIRS complete all as specified of Cat No CON-053KN of jaguar or equivalent

S&F( Fixed in repair) brass chromium plated towel rack 24'' long, fixed in position with steel screws complete all as specified of Cat No AQN-7781A 600mm long of jaguar or equivalent.

S&F( Fixed in repair) cast copper alloy , chromium plated a recessed toilet paper holder , FIXED IN REPAIRS, complete all as specified of Cat No AKB-35751 of jaguar or equivalent.

S & F in repair soap Dish complete all as specified of Cat No AQN 7731of Jaguar or equivalent

S&F( Fixed in repair) hand jet heath faucet 15mm bore with all connected fitting . Make:- Jaguar/ Hindware/cera

Supplied and fixed in repair CP corner shelf as approved by user Make:- Jaguar

S & F CP Grating 150mm size ( minimum weight 100 gm ) fixed in repair

S&F( Fixed in repair) vitreous china wash down water closet pan ( padestal pattern ) with and including waste fitting, waste pipe, flushing cistern and seat cover etc. FIXED IN REPAIRS, complete all as specified ( complete set and fitting) JAQUAR Cat No SLS-WHT-6851S110PP

S & F in repaire coloured TABLE TOP wash hand basin with built up with cabinet Make Jaquar Cat No SLS-WHT-6901 or equivalent with stainless steel brackets all as specified & directed.

M&L Light shade double charged Vitrified ceramic tiles 10 mm thick (Square/rectangular) polished, area of each tiles exc 0.42 sqm but n exc 1.0 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to mach including over 15 mm thick screed bed in CM 1:6 make oriented Bell/Kajaria/Jhonson/Somany .

Ditto as item above but in skirting.

S & F VAYU SHAKTI Emblem having 4mm thick pvc sheet dia 60 cm with flux glow sign incl brackets of FI 20mmX3mm for electric pole/wall approx 100 to 150mm dia all as specified and directed.

M & L for PVC flex n'exc 1.5mm thick of any shape and size fixed to existing aluminium /steel/acrylic/wooden frame with screws and appropriate fittings & fixtures with flex glow sign airforce monogram including required taxt as semple kept in 3 AFRU including sticking/ paste by pressure application including care to match the photo of monogram without any depreesion / undulation 6 Nos of monogram.

M & L for acrylic sheet 3 to 5 mm thick of any shape & size fixed to existing aluminium/steel / acrylic / wooden frame with screws and appropriate fittings & fixtures with flex sign Air Force monogram incl required text as semple kept in 3 AFRU incl sticking/paste etc. complete all as specified and directed.

Stone railing having both side carving of approved design and pattern (Jali pattern) Type "B" using yellow Jaisalmer stone) all as for type "B' and Sketch 'A' shown on drawings No.SKETCH/DRG/GE/(AF)/J/01/2021suitable for flat surfaces containing 30-40cm wide, 10cm thick base stone fixed in existing floor after cutting 50mm deep groove of width equal to base stone width and fixed to existing floor using proper adhesive as per manufacture's instructions. The stone railing to be fixed in base stone in groove 50mm deep (groove to be cut in base stone also) using adhesive with drilling holes in base stone and jalli balusters using non corrosive dowel pins) the hole should be filled with non-shrink or a polymer modified thin set grouted mechanically. The stone jali / railings are to be anchored by drilling holes in stones & bottom edge of Jali units. The holes should be slightly larger than the diameter of non-corrosive dowel pin. The dowel pin to be set in base stone using epoxy resin or high strength non shrink grout. Once the pins are set lower the jali unit on to the pins and into the morter/ adhesive bed. The horizontal joint between the Jalis should also be secured using small pins to be used horizontally to connect to adjacent Jalis units or baluster embedded with epoxy. The joint should be filled with as weather resistant non shrink mortar or grout that matches the color of Jaisalmer stone match the natural texture of stone all as specified and directed. Note: (i) Measurement will be taken from top of base stone to bottom of newel cap and gross measurement with post will be taken for all carving areas for payment purpose. (ii) Rates are included base stone, newel post, stone railing with all suitable fixing arrangements in position as directed. (iii) Sketch-1 of required design enclosed for ready references. (iv) Design and colour of stone shown on sketch for reference only. The same shall be approved by GE before execution of work/order by contractor.

M&L for stone railing/jalli having both side carving of approved design and pattern (Mehrav pattern using yellow Jaisalmer stone) all as for type "A' and Sketch 'A' shown on drawings No. SKETCH/DRG/GE/(AF)/J/01/2021 suitable for flat surfaces, containing base stone 30-40cm wide, 10cm thick, in existing floor after cutting 50mm deep groove of width equal to base stone width and fixed to existing floor using proper adhesive as per manufacture's instructions. The stone railing to be fixed in base stone in groove 50mm deep (groove to be cut in base stone also) using adhesive with drilling holes in base stone and jalli balusters using non corrosive dowel pins) the hole should be filled with non-shrink or a polymer modified thin set grouted mechanically. The stone jali / railings are to be anchored by drilling holes in stones & bottom edge of Jali units. The holes should be slightly larger than the diameter of non-corrosive dowel pin. The dowel pin to be set in base stone using epoxy resin or high strength non shrink grout. Once the pins are set lower the jali unit on to the pins and into the morter/ adhesive bed. The horizontal joint between the Jalis should also be secured using small pins to be used horizontally to connect to adjacent Jalis units or baluster embedded with epoxy. The joint should be filled with as weather resistant non shrink mortar or grout that matches the color of Jaisalmer stone to match the natural texture of stone all as specified and directed. Note :- (i) Measurement will be taken from exposed bottom of base stone to top of highest horizontal member of railing). No deduction for opening area to be made. (ii) Rate includes base stone, newel post, stone railing with all suitable fixing arrangements in position.(iii) Sketch shown on drawing is Schematic only.Detailing/ carving shall be done as per photograph/ image shown on the drawing.

M&L for stone railing of approved design and pattern suitable for slant profile as in stair all as for type 'C' and Sketch 'C' shown on drawings No. SKETCH/DRG/GE/(AF)/J/01/2021 containing base stone 30-40cm wide, 10cm thick fixed in existing floor after cutting 50mm deep groove of width equal to base stone width and fixed to existing floor using proper adhesive as per manufacture's instructions. The stone railing to be fixed in base stone in groove 50mm deep (groove to be cut in base stone also) using adhesive with drilling holes in base stone and jalli balusters using non corrosive dowel pins) the hole should be filled with non-shrink or a polymer modified thin set grouted mechanically. The stone jali / railings are to be anchored by drilling holes in stones & bottom edge of Jali units. The holes should be slightly larger than the diameter of non-corrosive dowel pin. The dowel pin to be set in base stone using epoxy resin or high strength non shrink grout. Once the pins are set lower the jali unit on to the pins and into the morter/ adhesive bed. The horizontal joint between the Jalis should also be secured using small pins to be used horizontally to connect to adjacent Jalis units or baluster embedded with epoxy. The joint should be filled with as weather resistant non shrink mortar or grout that matches the color of Jaisalmer stone to match the natural texture of stone all as specified and directed. Note :- (i) Measurement will be taken along slant/slopping length for paymnet. (ii) Rate includes base stone, newel post, stone railing intermediate post with all suitable fixing arrangements in position.(iii) Sketch shown on drawing is Schematic only.Detailing/ carving shall be done as per photograph/ image shown on the drawing.

M&L preparation of old jaisalmer stone/ Granite/Marble in any pattern surfaces of any description washing of complete prepared railing/floor etc with mixture of water and acid followed by coloured cement polishing with pigment to match the natural texture of stone/extg surfaces all as specified and directed.

Coloured Johnson endura tiles size 300mmx300mmx10mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over 15mm thick screed bed in CM 1:4 complete all as spd and dir.

M&L for chequered cement concrete tiles 300mm X 300mm x 25mm thick, set, jointed and pointed in near cement slurry in floor with grey cement and pigment including 20mm thick screed bed in CM (1:6) complete all as specified and directed.

M & L for machine pressed precast concrete interlocking paver block rubber moulding any shape and size with grey cement and pigment cnfirming to IS-15658-2006 of 60 mm thickness, M-35 grade over and 25mm thick sand/stone dust complete all as spfd & directed by Engr-in-Charge. (Sand cusion paid separetely)

Demolition of Stone slabs and tiles laid dry and pointed of any description or thickness in floors, aprons etc complete all as specified and directed

M&L Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L mirror polishing on marble / granite / kota stone / stone work where ever required to give high glass finish complete.

M & L in repair 12mm thick plain/froasted toughened glass door including stainless steel door handle 300mm long decorative type incl all necessary connected fittings and fixtures for door all as specified and directed.

M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixe incl necessary connection incl taking down old u/s floor spring all as specified and directed.

M & L for 12mm thick plain / froasted toughned glass with aluminium frame supplied and fixed at site in aluminium snap bedding fittings for glass all as specified and directed.

M & L for tinted/froasted film over toughned glass with Airforce logo all as specified and directed.

M&L for Standard aluminum anodised section frame work for chowkats /doors / windows shutters with style and rails or for fixed glazed partition wall frame made to shape required fixed with 150mm long screw and rawl plug incl necessary joining cleats,glazing clips,rubber packing ,anodised aluminium snap beading ,screws etc complet incl taking down old one all as specified and directed.

S&F 200 mm size aluminium anodised, barrel tower bolts of extruded section and fixed to aluminium frame incl Taking down old one.

S&F extruded aluminium alloy handles, fabricated type, anodised 150 size fixed to aluminium frame incl taking down old one.

S&F brass 4 lever Mortice lock, vertical type, size 100 mm fixed to aluminium door and frame incl taking down old one complete all as specified and directed make Harrison/Godrej.

S&F Aluminium (extruded section) body Door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed incl taking down old one.

S/F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm incl taking down old one.

M&L tinted Sheet glass 4.8mm thick , ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

S&F 150 mm size aluminium anodised, barrel tower bolts of extruded section and fixed to aluminium frame incl taking down old one.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm all as specified and directed.

S & F in repairs PVC connections 15mm size with PTMT nuts of length 600mm.

M&L Welding in repairs n.exc 2.5 cm in length, thickness of mild steel members to be welded not exc 6 mm complete all as specified and directed.

M&L Welding in repairs exc 2.5 cm but n. exc 5 cm in length, thickness of mild steel members to be welded not exc 6 mm complete all as specified and directed.

S&F in repairs stainless steel curtain rod 25 mm dia fancy type (SS-304) including Fency bracket & fittings including dismantling

M/s Ramesh & Company (BID ID -3483344)

M/s Fateh Enterprises (BID ID -3483271)

M/S MAYA CONSTRUCTION COMPANY (BID ID -3477962)

KHUSBU CONSTRUCTION COMPANY (BID ID -3477986)