ADDITION ALTERATION AND SPECIAL REPAIRS TO CERTAIN MD ACCN AT DINJAN UNDER GE DINJAN

Amount

Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed.

M&L for PCC (1:4:8) Type D2 (Using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete (sunken floor) complete as specified and directed.

Dismantling of floor hearth and wall tilling including cement mortar beding removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove, dust complete all as specified and directed.

M&L for light shade vitrified tiles 9 to 10 mm thick(square/ rectagular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer of cement mortar for laying floor finishes in cement mortar (1:6) complete all as specified and directed.

M&L for light shade vitrified colour tiles 10 mm thick (square/ rectagular) area of each tile exceeding 0.36 sq m but not exceeding 0.42 sqm , as in vertical surfaces such as skirting/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for Non Skid ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer of cement mortar for laying floor finishes in cement mortar (1:6) complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, coloured tiles as in floor. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed beb or bedding layer in cement mortar (1:6) for receiving the wall tiles complete all as specified and directed.

M&L for Non Skid ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , as in vertical surfaces such as skirting/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, coloured tiles as in skirting. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM (1:4) for reciving the wall tiles complete all as specified and directed.

M&L for Granite (of any type) tiles 20-25 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types as in wash basin top including 15 mm thick cement screed in CM (1:6) complete all as specified and directed.

M&L for 450x300x7mm thick glazed ceramic colour tiles on vertical surface set in neat cement slurry and pointed in white or coloured cement including 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM (1:4) for reciving the wall tiles complete all as specified and directed.

M&L for Kota Stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15mm thick screed bed in CM (1:6) complete all as specified and directed

M&L for Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for Laquer coated Chequered cement concrete coloured tiles 30 cmx 30 cmx25 mm thick set jointed in neat cement slurry and pointed in grey cement mixed with pigment to match the shade of tiles including 15 mm thick cement screed in CM (1:6) complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified and directed.

M&L for half brick thick brick wall with sub class "B" bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on brick walls/ concrete surface including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for 15 mm thick rendering in CM (1:6) on fair faces of brick work including finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM (1:4) mixed with approved water proofing compound @ 3% by weight of cement or as per direction of manufacturer on fair faces of brick work including finished even and smooth without using extra cement complete all as specified and directed. Note: WPC shall be and paid paid separately as supply only ).

M&L 5 mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Supply only Integral water proofing compound ISI Marked

M&L for complete removal of exisiting treatment of wall and applying two coats of oil bound distemper over 1mm thick wall care putty and primer complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion over 1mm thick wall care putty and one coat of chalk whiting priming paint complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick putty complete all as specified and directed.

M&L for complete removal of existing treatment including preparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincluding 1mm thick putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator and acessories complete all as specified and directed.

M&L for preapration of old plastered surfaces including washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed

M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded crushed stone aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed.

M&L for providing precast cement concrete (1:3:6) , type C-0 using 12.50 mm graded crushed stone aggregate as in louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed.

Taking down chowkat or frame (without taking off shutter from the frame) not exceeding 1.5 sqm each complete all as directed

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) exceeding 1.5 sqm each but not exceeding 4 sqm complete all as directed.

S&F pressed steel frames for door 125mm X 60mm with one or more revates including necessary fittings lugs, hinges, lock strike plate complete all as specified and directed.

S&F pressed steel frames for door 105mm X 60mm with revates including necessary fittings lugs, hinges, lock strike plate complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be measured and paid separately under respective items)

S&F factory made 35 mm thick 2nd class hard wood panelled shutters (any number of panels) with panels 12 mm thick of veneered particle board medium density wood particle board with commercial faces both side (BWR type) complete all as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I, section-8, cluse 8.24 (a) complete all as specified and as directed.

S&F factory made PVC door shutter 30 mm thick (style) consisting of frame made out MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of Single Side Prelam PVC sheet 5mm thick used instead of Plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10 mm 90 degree bent edge. Stiles and rails and decorative PVC beading of 10 mm x 10 mm (90 degree ) used instead of exposed portion of PVC sheet beading complete all as specified and directed.

S&F factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded Prelam PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face as per manufacturer's drawing complete all as specified and directed.

S&F PVC moulded door frame of size 50 mm x 47 mm made out of single side prelam PVC sheet 5 mm thick used instead of Plain colour PVC sheet 5 mm thick reinforced with MS Square tube & edges will be painted to match with prelam sheet complete all as specified and as directed

S&F 75 mm size stainless steel butt hinges complete all as specified and directed.

S&F powder coated aluminium frame for ventilator of size 65 X 38 mm with anodized aluminium push/ pull glazed type shutter with glass and necessary jointing cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium handles, including supply and fixing of 4 mm thick frosted sheet glass panes complete all as specified and as directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening as per requirement complete all as specified and directed.

S&F factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + 0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 Nos, sliding sash (30 mm x 18 mm), sliding mesh sash (26 mm x 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, Hardware (Touch Lock of zinc alloyed white powder coated),steel roller system. Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) Area not exceeding 2.00 sqm each complete all specified and directed

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S&F 250 mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 Nos of bolt and nuts, four Nos on bolt plate and two Nos on staple plate complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and necessary welding work complete all as specified and directed.

S&F MS 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

M&L for rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging & guard bars also fastening etc. confirming to Fe 410-W (gde-E-250) quality-A and fixing complete all as specified and as directed.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

S&F in repairs rolled mild steel joist, channel, angle or tee section/hold fast/ wind ties fixed independently with connecting base plate etc complete all as specified and directed.

M&L for PCC (1:3:6), type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for inserting holdfast / filling of steel frame, etc including necessary form work complete as specified and directed.

M&L for preparation of new steel surfaces of any description exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

Taking up or down 15 mm dia steel tubing including fittings complete all as specified and directed.

Taking up or down 20 mm dia steel tubing including fittings complete all as specified and directed.

Supplying and laying of CPVC pipes 20 mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and directed.

Supplying and laying of CPVC pipes 25 mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided complete all as specified and directed .

M&L for providing RCC Shelves , deck slabs, canopies etc using concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) compleate all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 mm to 8 mm dia , cut to length , bent to shape required inluding cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as in reinforcement complete as specified and directed.

M&L for form work to soffits of suspended slabs, roofs slabs , landing covers and similar works not exc 200 mm thick complete all as specified and directed .

S&F PVC connection 15 mm bore with PTMT nuts of length 450 mm long complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without letter 'HOT' or 'COLD' with long screwed shanks &fly nuts, screwed for iron pipes of dia 15 mm complete all as specified and directed.

S&F in repair Bib taps, cast copper alloy with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferule, chromium plated fancy type for 15 mm bore pipes complete all as specified and directed

S&F in repair brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed.

S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S&F brass CP wall mounted/central hole basin mixer 15mm bore dia for mixing hot & cold water un telephonic screwed down for iron pipe and fixed complete all as specified and directed

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

S&F repair Gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions for 20 mm bore pipes complete all as specified and directed.

S&F in repair 50 mm bore ,high density polyethylene pipes (HDPE) of pressure rating 6 kgf/ Sqcm in waste pipe for WHB and sinks,complete all as specified and directed.

S&F waste coupling pipe (PTMT) 32 mm/ 40mm for wash basin and sink complete all as specified and directed

S&F in repair stop valves/angular stop cock, cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends fancy type for iron pipes or for unions for 15 mm bore pipes complete all as specified and directed.

S&F brass chromium plated tubular towel rail, 20 mm dia, D-type, 60 cm long between flanges complete all as specified and directed.

S&F PVC low level flushing cistern, white, 10 Ltrs capacity with all internal accessories & fixed to wall & making good to wall surfaces including taking down existing flushing cistern complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (Semi pedestal pattern Anglo Indian Type), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover, connection to drain or outlet complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size: 550 X 400 mm, excluding taps waste chain & plugs & porcelain stopper but including brackets, waste coupling including cutting for & pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repar sink made of stainless steel 1 mm thick kitchen or laboratory with plugs , washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe , overall size 495 mm x 420 mm and bowl size 410 mm x 330mm x 160mm complete all as specified and directed.

S&F in repair stainless steel plate rack, 1mm thick racks of standard qality 900x900x250 mm size complete all as specified and directed.

S&F in repair stop valves (Concealed type) fancy type chromium plated with long shank & cup for 15mm bore pipes complete all as specified and directed.

M&L for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement in plain cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate complete all as specified and directed.

M&L for special treatment of sunken portion of WCs/Bath & toilet executed in following stage:- Stage1:- Demolition of WC including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of WC or bath with wire brush to remove all loose dirts, oil grease including removing debries from site of work. Stage 2:- Providing 10 mm thick rendering in CM (1:3) mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity as per manufacturere`s instructions. Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) as per manufacturer`s instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coat shall be allowed to dry for 6 hrs before next coat) Stage 5:- Rendering 10 mm thick in CM (1:3) mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity as per manufacturere`s instructions. Stage 6:- All CI joints shall be filled with mixture of cement , fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP as per manufacturer`s instructions. Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:- Carryout ponding test for 48 hrs to ensure water tightness of repaired sunken portion and filling of sunken portion by cement concrete (1:5:10) type E2 using 40mm graded crushed stone aggregate as in lean concrete Note:- (a) only plan area shall be measured for payment under this items. (b) Depth of suken portion of WC`s/ bath shall be upto 35 cm which is to be taken into account while coating the rate against this item. (c) The rate shall be quoted by contractor shall deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths.

Dismantling asbestos cement plain building boards, any thickness including cover fillets from ceiling complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type-B-0 (using 12.50 mm graded drushed stone aggregate) mixed with approved WPC as per manufactures instruction as in roof padding/ Chajja, complete all as specified and directed. Note: WPC shall be measured and paid separately as supply only under respective item.

M&L for water proofing treatment to RCC roof slab, including parapet comprising of the following courses of treatment/specifications from bottom to top complete all as directed :- (a) Taking down existing roof treatment from roof and terrance, roughening old concrete surfaces by picking, sweeping, cleaning and washing down with water to remove dust to a distance exc 100 m and n. exc 250 m and Cutting out cracks to V-section in existing roof or terrace, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand (1:1) (By weight). (b) 20 mm thick screed bed or bedding layer in CM (1:4) mixed with and including water proofing compound as per manufacturers instruction on cleaned concrete surface of roof, finished the surfaces fair and even including curing the surfaces for 7 days by ponding of water. (c) Applying cold bituminous primer confirming to IS-3384-1986 @ 0.30 Litre per Sqm over the plastered surface. (d) Laying Atactic Polypropylene Polymer membrane 3 mm thick (minimum) weighing 3.50 Kg per Sqm reinforces with polyster non woven fabric weighing not less than 160 gms per Sqm by torch application as specified in SSR part-I clause No 11.44 (e) Applying one coat of aluminium paint @ 0.10 Litre per Sqm over APP membrane.

Dismantling of plain or corrugated steel sheeting any gauge any thickness including nainital or similar pattern roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of colour having tensile strength of 550 Mpa as roof covering/clading to wall , fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of an colour having tensile strength of 550 Mpa as roof covering/clading to wall , fixed with self tapping screws complete all as specified and directed.

Dismantling of frame work timber scantling 40 sqcm and over in section in any position complete all as directed.

S&F 2nd class hard wood timber scantling, clean sawn as in frame work, fixed with nails complete all as specified and directed.

S&F 6 mm thick HPSC non asbestos fibre cement Standard Ceiling board (decorative type) with powder coated exposed GI grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm/600 mm long and wall angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The main runners to be placed @ 1200 mm, The cross Tee 1200 mm will be inserted in the pre-cut slots of main runner at a regular interval of 600 mm to form a modular grid of 1200 mm x 600 mm. Additional cross Tee of 600 mm shall be placed perpendicular to the cross Tee 1200 mm long to finally form a grid of 600 mm x 600 mm. Grid of module size 600 mm x 600 mm shall be supported by 6 mm dia GI wire from purlins/soffit. 6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Standard Ceiling Board (Density > 1200 Kg/m3) of size 595 mm x 595 mm, conforming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8 should be placed in the Grid module complete all as specified and directed.

S&F 500 Ltrs capacity Rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position as specified in SSR Part-I including dismantling water tanks complete all as specified and diredcted.

S&F Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 210 gms) for 20 mm bore pipe complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110 mm bore single soketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75 mm bore single soketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius with out acces door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) reducers complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal, with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal, with access door complete all as specified and directed.

S&F in repair 18/19 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination and fixed with screws to timber frame work including teakwood lipping 6 mm thick fixed with nails (for modular kitchen) complete all as specified and directed.

S&F 75 mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised 40mm when flaps open complete all as specified and directed.

S&F 100 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Extruded brass handles, fabricated type polished 75mm long complete all as specified and directed.

S&F Stainless steel telephonic `C` 450 mm long for drawers complete all as specified and directed

Cleaning the blockage of drain pipe (SGSW/hume pipe) upto 150 mm dia by rodding from manholes and well flushing with water after cleaning the same as required and including disposing off the deposited sludge inside pipes to a distance exc 50 m & n.exc 200 mtr burried under ground (minimum 30cm below ground level) including necessary excavating of pits in soft/ioose soil and returning filling in including sprinkling of bleaching powder @ .20 Kg/Sqm and dressing of surplus soil around slope complete as directed.

Cleaning of manholes including taking out accumulated Semi liquid, sludge and other deposits such as broken bricks, silt etc from manholes of depth n.exc. 1.5 mtr, cleaning as directed and removing the same to a distance n.exc 50 mtr and burried under ground(min 30 cm below ground level) including necessary excavation of pits in soft/loose soil and returning, filling in including , sprinkling of bleaching powder @ 0.20 Kg/Sqm and dressing of surplus soil around to slope complete all as directed.

Cleaning the blockage in nahani trap in bathroom kitchen or blocked gully trap by using rubber hand pump and opening the eye and making the line clear for smooth function complete all as directed.

Cleaning of open shaft of Md accn Bldg including gully trap, cleaning with wire brush including of grass, roots,bushes and taking out accumulated garbage from shaft and removing the same to a distance n. exc 50m complete all as directed.

M&L for applyiing 15 mm thick plaster with polymer modified mortar fortified with SBR (Nito Bond SBR 45) in proportion (1:3) by weight 5 litr Nitobond SBR 45 added to 50 kg of cement with 13 litr of water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like complete all as directed

M&L for preapration of old plastered surfaces including washing rubbing down and stopping of distempered and painted surface of wall and applying two coats of white wash on wall complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying three coats of white wash on wall complete all as specified and directed

M&L for preparation of old steel surfaces of any description exc. 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repair Vitreous water closet (EWC) , white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover, connection to drain or outlet complete all as specified and directed.

S&F 18 mm thick UV coating, HDHMR board exterior grade including acrylic high gloss sheet of 3 mm thick over HDHMR board anti-fungal, moisture resistance anti borer as per IS 14587 for frame and shutter of kitchen cabinets/cupboards etc complete all as specified and directed.

S&F 18mm thick UV coating MDF board both side laminated with any colour anti-fungal, moisture resistance anti borer as per IS 14587 for kitchen cabinets/cupboards shelves fixing with 1st class HW lipping/beading complete all as specified and directed.

S&F partial overlay/fully overlay hydraulic self-closing concealed hinges having size103 mm/64 mm finish silver/nickel complete all as specified and directed

S&F Stainless steel cabinet/drawers handles having a length of 250 mm and shape complete all as specified and directed.

S&F Stainless steel modular thali plate basket SS304 size 520 x 485 x 200 mm heavy duty and grade steel with finish of zinc corrosion resistance telescopic drawer channel having weighing capacity of 25 Kg complete all as specified and directed

S&F Stainless steel modular perforated cutlery basket SS304 size 520 x 485 x 200 mm heavy duty and grade steel with finish of zinc corrosion resistance telescopic drawer channel having weighing capacity of 25 Kg complete all as specified and directed

S&F Stainless steel triple cutlery inserts having of 500 mm corrosion resistance telephonic drawer channel having weight capacity 6 Kg complete all as specified and directed.

S&F Stainless steel glass tray plate having length of 610 mm corrosion resistance telephonic drawer channel complete all as specified and directed

S&F Stainless steel hanging spice rack having three shelf spaces having length of 500 mm corrosion resistance telephonic drawer channel complete all as specified and directed

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same with cement mortar (1:3) and painted with white or coloured paint complete all as specified and directed

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar (1:2) (1 cement: 2 coarse sand) to match the existing floors with Chloroparyphos 20EC complete all as specified and directed.

M&L for Marble work 18-20 mm thick (table rubbed and polished) (Colour- Green) in steps, jambs, pillars, window cills, cooking platforms and like in vertical surfaces in/over 10 mm thick screed bed of cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble of any shade other than white and black complete all as specified and directed.

Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

M&L for GI wire netting of 0.90 mm dia and 12 mm mesh lathing to wood or metal studding, joist, etc in walls, ceilings etc including all laps, cutting and waste fixed with tinned tacks of wire staples etc complete all as specified and directed.

M&L for rendering 15 mm thick on one side of lathing in cement mortar (1:6) and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 20 mm thick on other side of lathing in cement mortar (1:4) mixing with WPC @ 3% by weight of cement consumed and finished the surfaces even and smooth without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid as supply only under respective item of BOQ.

Taking down carefully old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box, DBs etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed.

Disconnecting electric connections and taking down carefully ceiling fan / Exhaust fan, sealing cable end, dismantling blades and removing fan to keep in safe custody or to deposite in MES store and material and labour for painting fans with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing same after minor repair on completion of work complete all as specified and directed..

Material and labour for point wiring with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one light/ceiling fan/exhaust fan point controlled by one oneway switch complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one 3 pin scoket outlet of 5 amps on independent board point controlled by one oneway switch complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one 3 pin scoket outlet of 5 amps on Same board point controlled by one oneway switch complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one bell point point controlled by one oneway switch complete all as specified and directed.

Material and labour for power point wiring with 2.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 2.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one 15 Amp scoket outlet on independent board point controlled by one oneway switch complete all as specified and directed.

Material and labour for power point wiring with 4 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing caping and necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 4 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth for connection of one 15 Amp scoket outlet on independent board point controlled by one oneway switch complete all as specified and directed.

Supply and fixing modular switch one way 6 amps 1 module 240 Volts complete all as specifed and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps 240 volts 2 module complete all as specifed and directed.

Supply and fixing modular switch one way 16 Amps 1 module 240 Volts complete all as specifed and directed.

Supply and fixing modular socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

Supply and fixing modular bell push switch 6A, 1 module all complete all as specifed and directed.

Supply and fixing ceiling fan step modular step regulator ,120W, 2 module complete all as specifed and directed.

Supply and fixing ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified/directed.

Supply and fixing modular metal flush box 1/2 module complete all as specified and directed.

Supply and fixing modular metal flush box 3 module complete all as specified and directed.

Supply and fixing modular metal flush box 4 module complete all as specified and directed.

Supply and fixing modular metal flush box 6 module complete all as specified and directed.

Supply and fixing modular metal flush box 8 module complete all as specified and directed.

Supply and fixing surface mounting PVC modular box 1/2 module for surface point wiring complete all as specified and directed.

Supply and fixing surface mounting PVC modular box 3 module for surface point wiring complete all as specified and directed.

Supply and fixing surface mounting PVC modular box 4 module for surface point wiring complete all as specified and directed.

Supply and fixing surface mounting PVC modular box 6 module for surface point wiring complete all as specified and directed.

Supply and fixing surface mounting PVC modular box 8 module for surface point wiring complete all as specified and directed.

Supply and fixing modular white cover plate with frame 1/2 module suitable for modular metal flux box / or for surface mounting PVC modular box as per site requirement complete all as specifed and directed.

Supply and fixing modular white cover plate with frame 3 module suitable for modular metal flux box / or for surface mounting PVC modular box as per site requirement complete all as specifed and directed.

Supply and fixing modular white cover plate with frame 4 module suitable for modular metal flux box / or for surface mounting PVC modular box as per site requirement complete all as specifed and directed.

Supply and fixing modular white cover plate with frame 6 module suitable for modular metal flux box / or for surface mounting PVC modular box as per site requirement complete all as specifed and directed.

Supply and fixing modular white cover plate with frame 8 module suitable for modular metal flux box / or for surface mounting PVC modular box as per site requirement complete all as specifed and directed.

Supply and fixing modular blanking plate. Note: Make of modular switches, sockets, regulators, bell push, modular boxes flush type/surface type, cover plate and frame shall be of same make.

Supply and fixing exhaust fan of high grade plastic or ABS for corrosion resistance, single phase capacitor start 150 mm sweep with insulation class B/F having IP 44/IP 55 protection class and noise level <60 dB having totally enclosed fan cooled (TEFC) motor with power consumption not more than 30 Watt including hole cutting and supply and fixing of louver and making good.the disturbed surface, with 1400 rpm complete all as specified and directed.

Supply and fixing bell electric, ding dong type 240 Volts, single pole complete all as specified and directed.

Supply and fixing in repair ETPN MCB Distribution board double door 4 Way (8+12 Module) for mounting SPN/ SP/TPN/TP MCBs/RCBOs/SPDs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply and fixing in repair ETPN MCB Distribution board double door 6 Way (8+18 Module) for mounting SPN/ SP/TPN/TP MCBs/RCBOs/SPDs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply and fixing in repair MCB Distribution board SPN 12 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply and fixing in repair MCB Distribution board SPN 16 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply and fixing in repair MCB Distribution board SPN 8 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply and fixing MCB TPN 415 Volts, 10 KA , curve "C" complete of capacity 40 to 100 Amps complete all as specified and directed.

Supply and fixing RCBO four pole 30mA, nominal rating 25 KA, and cpacity 40/63 Amps, for earth leakage, overload and short circuit protection and to be housed in DBS complete including necessry connection complete all as specified and directed. Note: In case of tripping of RCBOs contractor shall be responsible for rectifying the wiring defect or replace wiring without any extra cost.

Supply and fixing RCBO double pole 30mA, nominal rating 25 KA, and cpacity 32 Amps, for earth leakage, overload and short circuit protection and to be housed in DBS complete including necessry connection complete all as specified and directed by Engr-in-charge. Note: In case of tripping of RCBOs contractor shall be responsible for rectifying the wiring defect or replace wiring without any extra cost

Supply and fixing Surge Protection Device (SPD) 4 module, 25 KA, 3Ph+N Right, T1+T2, limp 8 KA per pole, T2-60KA, fixed in Essential DB and making connections by using necessary thimble/washersetc of copper/brass material complete all as specified and directed. (For Officer Qtrs DB)

Supply and fixing Surge Protection Device (SPD) Single Phase and neutral, T2 -limb, Imax 20 KA per pole fixed in distribution board and making connections complete all as specified and directed. (for SPN DB 12/16 Way)

Supply and fixing in repair MCB SPN 32 Amps 'C' Series 10 KA, 240 volts complete all as specified and directed.

Supply and fixing in repair MCB SP 6-32 Amps 'C' Series 10 KA, 240 volts complete all as specified and directed.

Supply and fixing angular/batten holder PVC/Polycarbonate suitable for batten fittings including one LED Lamp of 9W complete all as specified and directed.

Supply and fixing LED Surface mounted Downlighter having dia of 153mm(± 3mm) & height of 60mm(± 3mm) delivering minimum system lumen output of 1500 lumens (±5%) and system wattage of 15W (±5%) & with a minimum system efficacy of 110 lm/W. The luminaire should have a color temperature of 6500°K, CRI≥80 and SDCM≤5. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminum. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The the successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with Technical bid. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire complete all as specified and directed.

Supply and fixing inverter type LED 4 ft luminaire polycarbonate with PC diffuser. The luminaire should have a 20 Watt LED and working temperature 10 degree centrigrate to 45 Degree centigrate luminate shall be designed to emit at least 2000 nominal lumen. The electronic driver used shall have power factor >0.90 and THD ≤25% suitable for and operating volatge range 160V to 360V, surge protection should be ≥ 4KV electric insulation should be ingress protection of IP-20 rated and compliance to IS-10322-5,1 and battery type Li-ion capacity 2600 mAH with power backup upto 4 hrs with at least 500 lm. The LED luminaire and its driver both should be BS registered complete all as specified and directed. Note: Only One light fitting shall be used for one house.

Supply, Installation, testing & comissioning of intregral LED 4ft luminaire of CRCA housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a 18Watt LED with colour consistency SDCM< 5,CRI> 80 and colour temperature - 4000 to 6500K, Luminaire shall be designed to emit at least 2000 nominal lumens at a system efficacy of at-least 120 lumen/watt, power consumption should not be more than 20W (+5%). the life of fixture (including Driver): 50000 burning Hrs.@ L70B50 Lumen maintenance @ design ambient temp 50 deg C. The electronic driver used shall have a power factor >0.95 and THD < 10% suitable for an operating voltage range of 150-270V AC current Ripple<5% internal surge protection should be minimum 2.5KV, electrical insulation class should be Class I &driver should be of class B serviceablility. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have in house NABL accredited lab conduct LM79, type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accredition certificate for luminaire manufacturer along along with technical bid. the LED Luminaire & It's driver both should be BIS registered contractor shall submit the following reports before supply of material for approvals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer type test certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver complete all as specified and directed.

Supply and fixing Integral / batten LED 2ft, 10 watt 220 V, luminaire made of CRCA housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit at least minimum 1200 system lumens at a system efficacy of at-least 120 lumen/watt. Power consumption should not be more than 10W (± 5%). The Life of fixture (Including Driver):50000 burning Hrs. @ L70B50 Lumen maintenance @ design ambient temp 45 deg C. The electronic driver used shall have a power factor 0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤ 5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I & driver should be of Class B serviceability. The luminaire shall be IP20 & IK02 compliant. The minimum dimensions (± 5mm) of the batten shall be 63mm(±5mm) X 63mm (±5mm)X 610mm(±5mm). The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with Technical bid. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Drivercomplete all as specified and directed.

Supply and fixing LED type wall mounted light fitting sutable for LED lamp 9-20 W , housing- glass, frosted type, metallic frame and including one LED lamp 12 watt complete all as specified and directed.

Supply and fixing Bldg security light fittings high-quality group control enabled integrated LED Building security Light with a minimum system lumen of 3000 lm and system wattage not exceeding 25W with a nominal system efficacy of 110 lumen/watt. The LED used shall have CCT of 5700K, SDCM ≤ 5 and CRI≥70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” & shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved & should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. The product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 & impact resistance shall be IK10. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 20 KV/10KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 10KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only & shall be from either Lumileds, Osram, Nichia, Cree & APT Electronics make or equivalent. The Driver should be asphalt potted & should be a BIS approved driver. The driver shall have operating voltage of 120V to 270V, PF≥0.95 @ full load, THD≤10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547 & IEC 61000-3-2. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & it's driver both should be BIS registered. contractor shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test report for luminaire as issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver and including 1.2m long 32mm dia GI pipe light grade bend to shape and fixed using two nos clamps fabricated using MS Flat iron 40x5mm including necessary nut bolts and washers and making electrical connection using 1.5 Sqmm, 3 core multi-stranded copper conductor PVC insulated and over all PVC sheathed cable form light fitting complete all as specified and directed

Supply and fixing LED light fitting 1x 10 Watt blukhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit with minimum 20 mm dia medium grade fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through casing capping and connected to common earth dolly including taking out the old existing sub main wiring and casing capping / conduit / batten complete all as specified and directed. Note:- Two runs of 6 Sqmm cable and one run of 6 Sqmm earth wire and one run of PVC conduit shall be measured as one unit length.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLS PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing caping of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old existing sub main wiring and casing capping / conduit / batten complete all as specified and directed. Note:- Two runs of 6 Sqmm cable and one run of 6 Sqmm earth wire and one run of PVC casing caping shall be measured as one unit length.

Material & labour for Sub main wiring with four runs of single core 10 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit with min 25 mm dia medium grade fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 10 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old existing sub main wiring and casing capping / conduit / batten complete all as specified and directed. Note:- Two runs of 10 Sqmm cable and one run of 10 Sqmm earth wire and one run of PVC conduit shall be measured as one unit length.

Supply and Laying in repair XLPE insulated, Armoured, Electric Power UG Cable (Heavy Duty) with Aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 35 sqmm 3.5 core and Testing, including Brass Compression Cable Gland, Terminal Lug complete all as specified and as directed.

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated with all accessories such as safety valve, thermostate, NRV, connection piece complete all as specified and directed.

Supply and fixing GI pipe `Light grade', 32 mm Bore including all fitting; laid in trenches or fixed on wall commplete as specified and directed.

Excavating in Trenches not exceeding 1.50 m wide and not exceeding 1.50 m in depth for taking out and Laying of cables, and getting out in Soft/ Loose soil, complete all as specified and directed.

Returning and filling in, including spreading, levelling, watering and well ramming in layers not exc. 250 mm in Soft/Loose Soil, complete all as specified and directed.

Removing excavated materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the starting point complete all as specified and as directed.

M&L for sand cushioning, with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified. (Note:- Punned thickness shall be considered for payment purpose)

S&F Sub-Class B brick, well burnt, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and directed.

Boring under without disturbing the top surface of the road for passing and including GI protection pipe 50 mm bore medium grade , not exceeding 10 m in single length complete all as specified and directed. Note: Necessary infrastructure required for boring shall be arranged by the contractor at his own cost.

M P KHAITAN (BID ID -3422681)

NARSINGH DEVELOPERS LLP (BID ID -3425933)

DNS CONSTRUCTION COMPANY (BID ID -3425256)

Brahma Infra (BID ID -3425967)

Hariom Projects Pvt Ltd (BID ID -3424500)

BHOWMICK ENTERPRISES INDIA (BID ID -3425653)

MAA BHAGWATI ASSOCIATES (BID ID -3425666)