SPECIAL REPAIR TO COOK HOUSE T-9A TO INCL T-37 AND PROVN OF JCO/OR TOILETS (OTM) IN ZONE A, B, C, D AND PROVN OF RAIN WATER HARVESTING IN CWE ADM BLOCK AND OTHER MINOR WORKS UNDER GE JHANSI

Amount

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Excavating in trenches, n exc1.5 m wide and exc 1.5 m in depth but not exc 3.0 m; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Excavating over areas, not exc 1.5m deep and getting out as in hard dense soil complete all as specified and directed.

Excavating over areas, exc 1.5m and not exc 3.0m deep and getting out as in hard dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in hard/dense soil complete all as specified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Removing excavated soil exc. 250m but not exc 500m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Surface Excavation not exceeding 30 cm deep and averaging 7.5 cm deep and getting out in soft/ loose soil complete all as specified and as directed.

M & L for hard core of broken stone or boulder of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick watered and rammed to a true surface complete including filling interstices with approved fine material like earth or grit etc. complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed.

M & L for Cement concrete 1:4:8 type D-2(40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M & L for brick work with fly ash bricks (old size) straight or curved on plan exc 6m mean radius in CM 1:6 complete as directed.

M & L for salt glazed stone ware drain pipes laid in trenches and jointed and tested for 150 mm bore of pipe complete all as specified and directed.

M & L for cement concrete bed 1:3:6 type C-2 using 40mm stone aggregate to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M & L for Cement concrete 1:2:4 type B-2 using 40 mm graded stone aggregate in surface channels and drains complete all as specified and directed.

M & L for Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in surface channels and drains complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

M & L for Providing Reinforced Cement concrete 1:2:4 (Nominal Mix) type B-1 using 20 mm graded stone aggregate in cover slab (for manholes etc) set in CM 1:4 complete all as specified and directed.

M & L for Providing Precast Cement concrete 1:2:4 (Nominal Mix) type B-1 using 20 mm graded stone aggregate in cover slab (for manholes etc) set in CM 1:4 complete all as specified and directed.

M & L for brick work with fly ash bricks (old size) straight or curved on plan to any radius in half brick thick walls built in CM 1.4 exc 6m mean radius complete as directed.

M & L for 40 mm thick Cement concrete 1:2:4 type B-0 using 12.5mm gradred stone aggregate as in Damp proof course to horizontal or vertical surfaces with using water proofing compound including necessary formwork complete all as specified and directed.

Formwork for rough finished surface of concrete finished surface fair square, rectangular or polygonal to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and directed.

Formwork to flat soffits of suspended slabs finished surface fair such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick complete all as specified and directed.

Formwork for Rough finished surface of concrete finished surface fair to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed.

Formwork for Rough finished surface of concrete finished fair to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M & L for Reinforced cement concrete (Nominal Mix) M-25 (20 mm graded stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed.

M & L for Reinforced cement concrete (Nominal Mix) M-25 (20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Reinforced cement concrete (Nominal Mix) M-25 (20 mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels complete all as specified and directed.

M&L for Reinforced Cement concrete 1:2:4 (nominal mix ) (20 mm graded aggregate ) as in slabs supported on walls beam and coloums in floors ,roofs ,landing balconies ,canopies,deck slabs and in shelves and the like..complete all as specified and directed.

M & L for Reinforced cement concrete (Nominal Mix) M-20 (20 mm graded stone aggregate) in on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 ) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over a layer of (JK/Birla) 3.0 mm thick wall care putty to get smooth and level finish, complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M & L for cutting and chaseing in brick wall for concealed GI tubing and making good in CM 1:4 n.exc 10 cm in girth complete all as specified and directed.

S & F Galvanized iron pipe, 20mm bore, medium grade, with all fittings & fixed complete to walls and ceiling or laid in floors all as specified and directed.(cutting chase for concealing of pipe shall be measured separately) all as specified and directed.

S & F Galvanized iron pipe, 15mm bore, medium grade, with all fittings & fixed complete to walls and ceiling or laid in floors all as specified and directed.(cutting chase for concealing of pipe shall be measured separately) all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

M & L for 75 mm thick cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) with finishing cement concrete even and smooth as in plinth protection complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for joint free, Vitrified Ceramic tiles of light shed 10 mm thick (square/rectangular) polished , area of each tile exc 0.42 but n.exc 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering in CM 1:4,complete all as specified and as directed.

M & L for Coloured Non -Skid Ceramic tiles 7 to 8 mm thick, area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry & pointed in coloured cement to match the surface over and including 15 mm thick screed bed in cement morter (1:6) complete all as specified and directed.

M&L for non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M&L for 18-20 mm thick granite slab of any type , tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like and over 10mm thick backing coat rough finish/ screed bed in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate bedding of tiles/Kota stone all as specified and ditedted at site complete all as specified and directed. Note : Padding will be provide where require as directed by Engg-in-Charge

M&L for 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.)

S & F PVC (SWR) 'P’ trap (110/110mm ) complete all as specified and directed.

S & F 110mm PVC SWR pipes single socketed in any length with cement joints, laid in trenches or in floor complete all as specified and directed.

S & F PVC (SWR) junction single, (Single T) 110 mm dia equal or unequal complete all as specified and directed.

S & F 75mm PVC (SWR) pipes single socketed in any length with cement joints, fixed to wall complete all as specified and directed.

S & F PVC (SWR) cowel 75mm dia all as specified and directed.

S & F 75mm dia pvc Floor trap incl grating fixed in floor with cement all as specified and directed at site all as specified and directed.

S & F in repairs 75mm dia pvc Floor trap incl grating fixed in floor with cement all as specified and directed at site all as specified and directed.

S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) bends any 75 mm dia with access door complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawingcomplete all as specified and directed.

Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed.

M & L for providing cement concrete 1:2:4 Type B1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs complete all as specified and directed.

S & F Steel ventilator with top hung shutter in two parts, bottom portion for glazing and top portion for wiremesh, including hinges, steel peg stay, complete all as specified and directed.

S & F 100 mm size Butt hinges,stainless steel "medium weight". complete all as specified and directed.

S & F alumunium handle fabricated type anodised 150mm long as directed.

S & F 200mm long alumunium anodised barrel tower bolts of extructed section as directed.

S & F Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L 15 mm thick rendering in CM (1:6 ) on fair faces of brick wall or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L 10 mm thick rendering in CM (1:3 ) on fair faces of brick or concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for forming drip course in CM 1:4 of section/size exc 10 sqcm but n.exc 25sqcm complete all as specified and directed.

M & L for 15mm thick rendering on other than fair faces of brick work in CM 1:4 including using integral water proofing compound finished even and smooth without using extra cement complete all as specified and directed. NOTE-WPC shall be measured & paid separetly.

Supply only integral water proofing coumpound conform to the requirements of IS 2645: 2003 complete all as specified and directed.

S & F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of bedding with PCC type B-I 1:2:4, using 20mm graded crushed stone aggregate complete all as specified and directed.

S & F vitreous china Water closet pedestal pattern with seat cover white and flushing pipe 32mm dia for low level flushing cistern (excluding fixing bolts, flushing cistern and flush pipe) including Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc complete all as specified and directed.

S & F 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed .

S & F Vitreous China wash basin, white, flat back, size 600x480mm excluding ditto but including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S & F Vitreous chinal urinal half stall type of size 355 x 345 x 535mm complete including provision and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal in back of cement including connecting to flushing pipe and outgoing pipe complete all as specified and directed.

S & F cast copper alloy fancy type bib taps chromium plated 15mm bore pipe with capstan head complete all as specified and directed.

S & F Pillar taps, cast copper alloy, with fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15 mm bore and fixed complete all as specified and directed.

S & F 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F stop valve 15mm bore cast copper alloy screwed down high pressure chromium plated with long shunk and cup concealed type complete all as specified and directed.

S & F Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S & F stainless steel peg sets consist 06 Nos of pegs of approved quality complete all as specified and directed.

M & L for 100 mm thick cement concrete 1:2:4 type B1(20mm graded stone aggregate) at roof top for bed of water tank complete all as specified and directed.

S & F Gun-metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe all as specified .

S & F rotational moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I complete all as specified and directed.

S & F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball & fixed complete all as specified and directed.

M & L for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M & L for preparation of New plastered surface of walls and applying two coat of cement based paint over a coat of white cement primer. complete all as specified and directed.

M & L for provision of roof treatment with polymeric water proofing membrane all as given below :- (a) M & L for plastering 10mm thick in CM 1:3 using 100% coarse sand on roof including water proofing compound as per manufacturers instruction and as directed by Engr-in-Charge. (b) Applying a coat of bituminous primer conforming to IS : 3384-1986 @ 0.40 Iitres/sqm. (c) Applying and laying 3mm thick APP membrane having non oven polyester Matt at core and covered with high quality polymeric asphaltic protected with thermo fusible HMHDPE film on both side and over laps 10cm and 15 cm longitudinal and transverse respectively and sealed by flame, sealing all overlap complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar. (d) M & L for two coats of aluminium paint over bituminous surface all as specified and directed.

Labour only for soil filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed.

All as per item No. 99 here-in-above but not exc 1.5 sqm each complete all as specified and as directed.

Supply and fixing factory made uPVC white colour fixed glazed ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, including 6 mm thick full length toughned glass, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be cceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. including 6 mm toughned full length fancy type glass and wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners incl in this item of required dia and length complete as per direction of Engineer-in-Charge.

S&F of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with beads , complete all as specified and directed.

M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

S&F in replacement PVC (PTMT) connection 15 mm dia and 600 mm long complete all as specified and directed.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe)

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore, jointing to waste pipe, complete all as specified and directed.

M & L 25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

M & L 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

Dismantling timber scantlings any size and section, in any position complete all as specified and directed.

M&L for second class hard wood plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

Supply only continuous (piano) hinges, mild steel bright finish or electro galvanized , width of flaps (when open) 40 mm, complete all as specified and directed.

S & F brass drawer/shutter handles fancy type , projection drop (50mm to 65mm) on screwed platey complete all as specified and directed

Supply and fix glass sliding shutter for Showcase /Bar using 5.5 mm transparent thoughned glass , aluminium two track rail all around the glass fixed with SS screw, including S S roller assembly for movement of glass shutter , including all necessary accessorries required for horizontal movement of two track glass shutter complete all as specified and directed

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, ISI, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed.

S&F in replacement of premium quality corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed.

M&L in repair for stainless steel curtain rod 25mm dia with fancy caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed by Eng-In-Charge Note: Bracket and end caps/lobs are included in quoted rate.

S & F in repair chromium plated shower rose 150 mm size fancy type with or without swivel joints, any size, including fixing to steel pipe or union

S&F in replacement of 1st quality handshower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed.

S&F in replacement of CP towel rail 600 mm long fancy type with wall bracket made of cast copper alloy, chromium plated, complete all as directed.

S&F SS grating of round shape dome type 4" to 5", floor trap traps etc, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion and plastering to edges is included in quoted rate.)

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for wind ties as in Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engrr-in-Charge.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern complete all as specified and as directed.

S & F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws inclu dismantling of old existing sheet of any description complete all as sepcified and directed.

Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets etc, complete all as specified and directed.

M&L 4mm th Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equalflanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, duly fixed in ceiling frame work, complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

M & L for Filleting in any position and to any shape in cement mortar 1:4 including all mitres, stops, etc. exc 50 but n.exc 100 sqcm in section including excavation and earth work complete.

M&L for cutting and screwing of existing steel tubing for alterations or addition of size 40mm or 50mm done in position without taking down and inserting tee branch connection complete all as specified and directed.

M&L for brickwork with sub clas 'B' bricks (old size) straight or curved on plan exc 6.00 m mean radius built in CM 1:6 complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, removing materials for taking credit and making good disturbed surfaces of walls, floors, etc with cement plaster, putty and paint to match with the existing surface complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG / with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated sheet fixed with brass/GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points :-

One light / ceiling fan / exhaust fan point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per item No. 154.00 here-in-before but one 16A socket point controlled by one 16A switch on independent board with 2.5 sqmm FRLS copper wires.

All as per srl item No. 154.00 here-in-before but with 4 sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

M&L for sub main wiring along with earth wire with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 25mm concealed in wall/ floor etc complete all as specified and directed for the following sizes:- (Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length)

2runs x 4 sqmm(Ph & N) + 1run x 4 sqmm(earth wire)

2runs x 6 sqmm(Ph & N) + 1run x 6 sqmm(earth wire)

Notes for item No. 154 to 157.03 (i) Quoted rate shall deemed to include the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & capping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing capping may be used in that portion.

S&F of Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F of Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.

S&F of electronic fan regulator in 5 steps, 240V, 50Hz complete all as specified and directed.

S&F of Socket 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

S&F of Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

Supply and fix of Lamp holder, angle type with metal ring, PVC/Polycarbonate body including taking down existing unserviceable lamp holder of any description complete all as specified and directed.

S&F of Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix of integrated LED batten 10 watt, 2 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix of modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 20A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board including taking down existing unserviceable plug & socket board of any description and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fix of integrated LED batten 20 watt, 4 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling (Cool and warm white) including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed by Engineer-in-Charge.

Supply and fix of LED street/security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver and surge protection upto 10 Kv complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including provision of GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable of size 0.5 sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and as directed.

Supply and fix of electric water heater, storage type steel body with glass lined inner tank and heating element 2 KW of capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.complete all as specified and as directed.

Supply and fix of ceiling fans complete with blades, down rods, 230 V, 1200 mm sweep. ( with remote) Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

All as per item No. 172 here-in-before but SPN, 12 way, 230 V, 1 phase, AC complete all as specified and as directed. Note: MCBs shall be measured and paid separately.

All as per item No. 172 here-in-before but SPN, 8 way, 230 V, 1 phase, AC complete all as specified and as directed. Note: MCBs shall be measured and paid separately.

All as per item No. 172 here-in-before but SPN, 4way, 230 V, 1 phase, AC complete all as specified and as directed. Note: MCBs shall be measured and paid separately.

Supply and fix of MCCB 100A, 16 KA, 4 Pole, 415 V, 50 Hz with fixed thermal magnetic release complete all as specified and directed.

Supply and fix of MCB 63A, 10 KA, TPN, 415 V, 50 Hz complete all as specified and directed.

Supply and fix of MCB 40A, 10 KA, SPN, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply and fix of MCB 6 - 32A, 10 KA, single Pole, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply & fix ventilating fan plastic body with louvers 250mm sweep single phase 230 volts 50 Hz complete all as specified and directed.

Supply & fix of wall mounting fan 400mm sweep, 230 Volts single phase suitable for wall mounting with twin cord for speed regulation and oscilting the fan complete all as specified and directed.

Supply ,laying , fixing or passing through pipe 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire of strip and overall PVC sheathed in service connections 2 core cable flat or circular of size 10 sqmm as per IS 7098 (Part 1) including connecting on LT OH line / LT panel / DB with suitable lugs, glands, binding wire etc including taking down existing unserviceable service cables of any description complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Design, supply, instalation of rain water harvesting system with PVC underground water storage tank of 6000 ltrs capacity having following arrangements complete all as specified and directed :- (i) First flush system - 01 Set (ii) Gravity Filter - 01 Set (iii) PC delivery pipes 25mm size - 15 mtr (iv) Down take pipes 100mm size - 15 mtr Note :- Contractor shall submit technical design date and drgs duly vetted by auth vendor for approval of GE prior to commencement of work.

M/S Kharya Associates (BID ID -3336219)

FTH TRADERS (BID ID -3336353)

m/s ramesh saran agarwal (BID ID -3336227)

M/S Kumar Contractors (BID ID -3335483)

HARNAM SINGH ANIL SINGH (BID ID -3336833)

VIJAY BUILDERS (BID ID -3335957)

ADARSH ENTERPRISES (BID ID -3335474)