Construction of Nature Interpretation Centre (NIC) at Jambu Zoo, Nagrota, Jammu

Amount

Earth work in excavation by manual means over areas ((exceeding 30 cm and upto 1.50 mtr in depth, 1.50 mtr in width as well as 10 sqm on plan) incl. disposal of excavated earth upto 1 mtr from cutting edge, disposed earth to be levelled and neatly dressed. All kinds of soils.

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 2.9.1 All kinds of soil :

Filling available excavated earth (excluding rock) in trenches, plinth slides of foundations etc in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead up to 50 m and lift up to 1.5 m

Providing and Laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including all leads lift carriage complete job

Supplying and filling in plinth with fine sand under floors including watering, ramming, consolidating and dressing complete.

Providing and Laying damp proof course 40 mm thick with cement conc. 1:1.5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 12.5 mm nominal size) crushed including all leads lift carriage complete job

Making plinth protection 50 mm thick of cement conc. conc. 1:3:6(1 cement:3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed, consolidated and grouted with fine sand incl. Finishing the top smooth. including all leads lift carriage complete job

Providing and Laying in position specified grade of reinforced cement concrete excluding the cost of centring and shuttering-All work up to plinth level 1:1.5:3(1 cement;1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) crushed. including all leads lift carriage complete job

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string, courses, fillets, columns, pillars, piers, abutments, posts and struts etc up to floor five level excluding cost of centring, shuttering , finishing and reinforcement 1:1.5:3 including all leads lift carriage complete job

Providing and fixing 8 mm thick with angel frame 40x40x6mm toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge including Door handle, lock and stopper etc

Centring and shuttering including strutting , propping etc and removal of forms for Foundations, footings, bases of columns etc. For mass concrete.

Centring and shuttering including strutting, propping etc and removal of form for Columns, pillars, piers, abutments, posts, and struts.

Centring and shuttering including strutting, propping etc and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm Wide

Reinforcement for RCC work including straightening,cutting, bending, placing in position and binding all complete. Thermo mechanically treated bars.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanized Puff insulated roofing sheet (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing Ridges plain (500 - 600mm)

Providing and fixing Flashings/ Aprons.(Upto 600 mm)

Providing and fixing Barge board (Upto 300 mm)

Providing and fixing Gutter .(600 mm over all girth)

Brick work with F.P.S bricks of class designation 75 in foundation and plinth in cement mortar 1:6 (1 cement: 6 coarse sand) including all leads lift carriage complete job

brick work in superstructure above plinth level upto floor V level

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS 733 of IS: 1285, fixed including necessary filling up of gaps at junctionsi.e at top, bottom and sides with required EPDM rubber/ neoprene gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, CP Brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer Incharge (glazing, panelling and dash fasteners to be paid seperately). For fixed portion: Powder coated aluminium (minimum thickness of powder coated 50 microns)metre

For Shutters of doors, windows and ventilators including providing and fixing of hinges/pivots and making provision for fittings wherever required including the cost of EPDM rubber/neoprene gasket required (normal fittings shall form part of the item).Powder coated aluminium (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc with EPDM rubber/neoprene gasket etc. complete as per architectural drawings and directions of engineer-in- charge. (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5.00 mm thickness (weight not less than 13.50 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture, IS:6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floor, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M S sheet cover box with slide plate etc. complete as per directions of engineer-in-charge.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.00 mm thick, & 2100 mm long with S S screws etc. complete as per directions of engineer-in- charge. Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Nos

Providing and fixing aluminium round shape handle of outer dia. 100 mm with S S screws etc. as per directions of engineer-in-charge. Powder coated minimum thickness 50 micron aluminium

Providing and fixing 1st quality ceramic glazed tiles conforming to IS 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT, SOMANY KAJARIA or equivalent make in all colour, shades except burgundy, bottle green,black of any size as approved by Engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand) and jointing with grey cement slurry # 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. sqm

Providing and fixing ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming of Is: 13755 of NITCO, ORIENT, SOMANY, KAJARIA Or equivalent make incolour such as White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of cement mortar 1:4(1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc complete

12mm cement plaster of mix 1:6(1 cement:6 fine sand) including all leads lift carriage complete job

15mm cement plaster of mix 1:6(1 cement:6 fine sand) including all leads lift carriage complete job

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 13.88.1 1 mm thick

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) overand including priming coat with water thinnable cement primer

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 600mm x1200 mm (TILES SHOULD BE KAJARIA,SOMANY)

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 11.58.4 Size of tile 1000x1000 mm

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge

Providing and fixing of outer stone tile for exterior peripheryPERFORATED TILE

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : 11.66.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and Fixing of Wiring of Lighting Point /Fan Point /Bell Point/Exhaust fan Points in 2x1.5 Sq. mm FR PVC Insulated Multistand Copper wire of ISI Marked including,G I Boxes , Circuit Wiring & 6/ 10 amp Switch of modular series ISI Mark ( excluding Cost of Conduit/Channel ) ( Approved Before Installation ) .

Providing and Fixing of Wiring for heating Points in 3x4 Sq. mm FR copper wire Multistand of ISI Mark including G I Boxes ,circuit wiring & 16 /20 Amp Switch Modular series ISI Mark( excluding Cost of Conduit/Channel ) ( Approved Before Installation)

Providing and Fixing of Wiring for Computer Point in 3x2.5 Sq. mm in mm sq. FR PVC Insulated Multistand Copper wire of ISI Mark to be laid in existing surface /recessed medium class pvc conduit /channels ( excluding Cost of Conduit/Channel ) including G I Boxes ,circuit wiring & the cost of supplying and fixing of 3 No’s 6/10 Amp 5 pin Socket with 1 No 6/ 10 amp control switch of Modular Series ISI Mark with necessary Connections. ( Approved Before Installation )

Providing and Fixing of Wiring for 6 Amp Wall Plug Points Computer Points in 3x2.5 Sq. mm in mm sq. copper wire multistand of ISI Mark including G I Boxes, 6 Amp Switch & Socket of Modular Series ISI Mark ( exec Cost Conduit /Channel ) ( Approved Before Installation).

Supply and fixing of 2mm thick 25 mm dia PVC Conduit/Channel Double Locked of ISI Mark With its allied accessories Complete Recessed in Slab and/ in Walls ( Approved Before Installation )

Providing and Fixi.ng of 350 Watt Electronic Fan Dimmer of Modular Series ISI Mark With Necessary Connections ( Approved before installation )

Supply and Fixing of 1400 mm Sweep Celling Fan OF ISI Mark Complete With Necessary Connections. Complete Job ( Approved before installation )

Supply and Fixing of 250/300 mm Exhaust Fan Shutter Type Of ISI Mark Complete With Necessary Connections Complete Job ( Approved before installation )

Supply & Fixing of Fancy Type Angle holder/Batten holder including 15 Watt LED Bulb of ISI Mark Complete Job with Necessary Connection of Complete Job. ( Approved before installation )

Providing & Fixing of Double Door Distribution Board of ISI Mark Recessed In Walls including Refacing of Walls. Complete Job ( Approved before installation )

Supply and fixing of 6 – 32 amp Single pole MCB C – Cure OF ISI Mark With necessary Connections. ( Approved before installation )

Supply and fixing of 32 amp Double pole MCB C – Cure Of ISI Mark With necessary Connections. ( Approved before installation )

Supply and fixing of 40 - 63 amp Double pole MCB C – Cure Of ISI Mark With necessary Connections. ( Approved before installation )

Providing & Fixing of 10 sq. mm FR PVC Copper wire Multistand of ISI Mark Laid in PVC Conduit/ Channels ( Excluding Cost of Conduit/ Channel ) for heating Sub Main Connections ( Approved before installation )

Providing & Fixing of 6 sq. mm FR PVC Copper wire Multistand of ISI Mark Laid in PVC Conduit/ Channels ( Excluding Cost of Conduit/ Channel ) for heating Sub Main Connections ( Approved before installation )

Providing & Fixing of 4 sq. mm FR PVC Multistand Copper wire of ISI Mark Laid in PVC Conduit/ Channels ( Excluding Cost ofConduit/ Channel ) for Computer /Lighting Sub Main Connections ( Approved before installation )

Providing & Fixing of 2.5 sq. mm FR PVC Multistand Copper wire of ISI Mark Laid in PVC Conduit/ Channels ( Excluding Cost of Conduit/ Channel ) for Computer /Lighting Sub Main Connections ( Approved before installation

Supply ,installation and commissioning of Main Control Panel board 415 Volt Duly maid of 16 SWG Protected and Vermin proof with Gas ket led Lockable doors complete with inner connections crimping legs bounding to earth terminals with following Controlling Equipment 1 No 250 amp TPN MCCB Of ISI Mark 200 Amp Bus bar Alum TPN 2 set and 12 No’s MCB 40-63 Amp DP C - Cure of ISI Mark including 125 AMP 4 Pole Change over ISI Mark , Volt /Amp Meter Complete Job . ( Approved before installation )

Supply and fixing of Main Service Line in 70 Sq. mm 3.5.Core Aluminiumarmed Cableof ISI Mark . ( Approved before installation

Supply, Installation and Commissioning of 10 KVA, 3Phase, 415V LT unbalanced AVR of ISI Mark . The servo voltage stabilizer shall operate from input voltage (L-N) =90-270V (L-L 155- 470V) thereby producing the corresponding output voltage of 415V ±5% (Phase to Phase) the servo stabilizer should further have inbuilt protections of over voltage, under voltage and overloading with TDR. The stabilizer shall be servo controlled automatic, ONAN cooled and provided with first filling of fresh filtered transformer oil having required di electric strength, the stabilizer shall further be capable of smooth operation upto 10% unbalanced in the load currents. The supplier has to give guarantee for any manufacturing defect with three servicing of equipment for 1 year reckoned after commissioning. ( Approved before installation )

"Providing of Maintenance Free Earthing System using copper bounded earthing steel rods 2 inches in dia and 2 Mts long placed vertically in a bore well of 4 Inch in dia dully bored manually with 250 micron copper molecular bonding along with 2 bags ( 11.5 Kg each) of Ground Enhancement Material (GEM) or Equivalent with each rod to reduce the soil resistivity to a considerable value.

Providing anf fixing Split AC 6 No. of 2 ton with Stabilizer of standard make like Bluestar,Voltas,Lg ,Hiterchi etc.complete job

Providing anf fixing Invertor of 5KVA with 6 no 150 Ah Batteries of standard make like luminous,SuKam etc complete job

Providing anf fixing Servo Stabilizer 20 Kw of standard make of ISI brand ,input-110 , 3 Phase with complete fitting

Providing anf fixing Stainless Steel Turbo Ventilator Roof Fan

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:White Vitreous China Wash basin size630x450 mm with a pair of 15 mm C.P. brass pillar taps Jacquar

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception ,, of pipes and fittings. Jacqurar,somany

Mirror with white plastic moulded frame oval shape 450x350 mm (Outer dimensions)

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete

Providing and fixing PVC waste pipe including PVC waste fittings complete 32mm dia

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap.

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 1 02mm, heigth of 75mm with concealed fitting arrangements, weighing not less than 1 06gms.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x41 Ox265mm sizes respectivelly with all complete fitting anmf fixtures Jacquar

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931.Jacqurar

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore Jacqurar,somamy,cera

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:15 mm dia. nominal bore medium

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:20 mm dia. nominal bore medium

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.

Providing and installation of Jet of approved brand

Providing and fixing toilet paper holder C.P. brass

Providing and fixing PVC /supreme brand heavy pipes 100mm

Providing and fixing PVC/supreme brand heavy pipes 75mm

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter Jacquar,Somany

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 a) 15 mm nominal bore Jacquar,Somany

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 a) 15 mm nominal bore Jacquar,Somany

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete15 mm nominal bore Jacquar ,Somany

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with divertor,seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied: W.C. pan with lSI marked white solid plastic seat and lid. Jacquar,SOmany

Providing and fixing Ornamental Railing as per the direction of incharge engineer at site Height of the railing 3 feet

Providing and fixing of Washbasin mixture Jacquar,Somany

Providing and fixing of Hand Dryer Jacquar

Providing and fixing of Soap Dispensor of jacquar

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and laying 80mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality. Square shape 350mm internal dimensions

Construction of RCC Uderground Water Tank of 12'x7'x6' in Size

Construction of RCC Septic Tank of 12'x8'x6' in Size

PROVISION FOR ARCHITECTURAL APPEARANCE @ 0.50% of advt. cost

Anil Gandotra

SALEEM ALAM, GOVT CONTRACTOR