AUGMENTATION / CLEANING / REPAIR TO SEWAGE SYSTEM, MANHOLE, SEPTIC TANK AND SOAKAGE WELL ETC IN ZONE A AT DAMANA UNDER GE JAMMU

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc and not exceeding 10 Sqm on plan and not exceeding 1.5 metre in depth and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

Demolition by breaking up drain pipes (salt glazed stoneware or AC / RCC) 150mm dia jointed in cement mortar and taking out of trenches and removing the debris including concrete bed and haunching from the trenches complete all as specified and as directed.

Material and labour for 150mm bore / inner dia double wall corrugated HDPE pipes (SN-4) with integral socket and necessary fittings, laid in trenches jointed as per manufacturer's instructions complete all as specified and as directed at site.

Material and labour for 150mm internal dia salt glazed stone ware drain pipe Class 'A' laid in trenches on concrete bedding jointed in cement mortar (1:1) complete all as specified and as directed.

Material and labour for concrete bed to drain pipes of bore 150mm dia including packing under haunching against the sides of pipe after they are laid tested in cement concrete (1:4:8) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and as directed.

Demolition by breaking up drain pipes (salt glazed stoneware or AC / RCC) 200mm dia jointed in cement mortar and taking out of trenches and removing the debris including concrete bed and haunching from the trenches complete all as specified and as directed.

Material and labour for 200mm internal dia salt glazed stone ware drain pipe Class 'A' laid in trenches on concrete bedding jointed in cement mortar (1:1) complete all as specified and as directed.

Material and labour for concrete bed to drain pipes of bore 200mm dia including packing under haunching against the sides of pipe after they are laid tested in cement concrete (1:4:8) type C-2 (using 40mm graded crushed stone aggregates) complete all as specified and as directed.

Demolition of brick works built in cement mortar including all quoins, pillars, arches etc including PCC benching / coping etc complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar (1:4) complete all as specified and as directed.

Description all as per Ser item No 12.00 here-in-before but except bricks complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in benching, coping etc including necessary form work complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside cantonment area all as specified and directed by Engineer-in-Charge. Note: - Plaster work may be in patches upto triple storey.

Material and labour for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surface finished even and smooth without using extra cement including mixing of integral water proofing compound in the proportion as per manufacturer's instructions complete all as specified and as directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 Cu.m, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

Material and labour for plain cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Supply and fixing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire; flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Grade 'E'-165 complete all as specified and as directed.

Material and labour for mild steel rag or lewis bolts 12 mm dia and nuts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, not exceeding 15 cm complete all as specified and as directed.

Material and labour for mild steel round bars 8 mm dia and over of Fe-410 W quality 'A' or Fe 290 quality-A, bent to shape required, including crancking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips in chain link fencing complete all as specified and as directed.

Material and labour for mild steel in flat, round or square bars, in available length 40 x 6 mm FI strip fixed to chain link fencing complete all as specified and as directed.

Dismantling fencing wire mesh any type complete all as specified and as directed.

Supply and fixing chain link fencing of 3.5 mm dia galvanised iron wires and 100 x 100mm mesh size including rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Supply and fixing in repairs 600 mm dia concertina coil complete all as specified and as directed.

Supply and fixing in repairs galvanized two strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanized mild steel wire staples or steel pins etc complete all as specified and as directed. Note: - Each line wire to be measured.

Restraining and resecuring including making good staples etc galvanized two strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanized mild steel wire staples or steel pins etc complete all as specified and as directed. Note: - Each line wire to be measured.

Material and labour for applying two coats of cement based paint over a coat of primer including preparation of new plastered surface of wall complete all as specified and as directed.

Material and labour for preparation of old plastered or unplastered surfaces of walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efflorescent salts and trading oil and greasy spot by using suitable chemical and removing nails, making good holes with chalk whiting, filling cracks and brooming to remove all dirt etc and applying one coat of cement based paint on old prepared surfaces of walls complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint on new steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface complete all as specified and as directed.

Cleaning and clearing the blockage of sewage lines of any dia, type and any depth, removing any type of blockage by roding from manholes or by flushing water with pressure pump complete all as specified and as directed.

Taking out of solid / semi solid sludge from existing manholes of any size and any depth and burying the entire sludge / sludge water into excavated pit of adequate size including excavating and covering with earth or disposing off into covered vehicles outside the peripherry of defence land to a distance exceeding 1 KM including taking off RCC / iron manholes covers and refixing the same after cleaning complete all as specified and as directed.

Cleaning of blockage of EWC / IWC / urinal / bathroom / kitchen and gully trap and removing of sludge / soil / waste to distance exceeding 100 metre and testing of water closet block for proper working after cleaning complete all as specified and as directed.

Notes: - For Ser item No 32.00, 33.00 and 34.00 provide two sweepers on daily basis for attending day to day complaints and clear blockage in all respects whether in water closet, Bathroom, kitchen, gully trap, sewage lines and manholes at any place upto septic tank and soakage well complete. Both the sweepers will report to the complaint cell at 9:00 AM daily except Sundays and Gazetted Holidays and will leave the cantt premises after 5:00 PM. In case the persons are not provided, Rs 400 per day per person will be recovered. The attendance of the sweepers will be marked at 9:00 AM and 5:00 PM. The sweepers will be issued complaints by the complaint cell and they will submit the complaints on completion on the same day otherwise Rs 100 per complaint per day will be charged for delay in completion. No T&P will be issued by the department to the sweepers. It will be the responsibility of the contractor to provide adequate T&P including uniform to the sweepers.

Removing the manhole cover (CI or RCC), any type of manhole rectangular / circular and de-watering of septic tanks and soakage wells of any size and depth by means of hydraulic jet pressure machine by plugging inlets as required, making it fully functional to the entire satisfaction of Engineer-in-Charge including carrying the effluent outside the defence land in closed containers and reinstating the manhole cover to its original position complete all as specified and directed by Engineer-in-Charge. Note: - The quoted rates includes for keeping the particular septic tank and soakage well undertaken once for desludging / de-watering functional for full contract period.

Removing the manhole cover (CI or RCC), any type of manhole rectangular / circular and de-sluding of septic tanks and soakage wells of any size and depth by means of hydraulic jet pressure machine by plugging inlets as required, making it fully functional to the entire satisfaction of Engineer-in-Charge including carrying the effluent outside the defence land in closed containers and reinstating the manhole cover to its original position complete all as specified and directed by Engineer-in-Charge. Note: - The quoted rates includes for keeping the particular septic tank and soakage well undertaken once for desludging / de-watering functional for full contract period.

Notes: - For Ser Item No 32.00, 33.00, 34.00, 36.00 and 37.00: - (i) The sewage line is required to be cleaned by using water jetting machine as directed by Engineer-in-Charge. The unit rate quoted by the contractor shall deem to be included of this provision and no extra claim on this account shall be entertained by the department. Jetting machine will be compulsory minimum three times a week otherwise one day recovery of Rs. 10,000/- will be deducted from the payment due to the Contractor. (ii) Contractor during the mechanized operation shall be equipped with gas monitor, nylon rope ladder, torch light and compressor blower etc along with the sewage cleaning truck mounted suction / jetting machine. (iii) Manual cleaning operation / Scavenging is prohibited. (iv) The unit rate quoted by the contractor shall interalia deemed into the cost of providing skilled driver and operator and supervising engineer including provn of water for jetting and removal of sludge / silt / liquid / mud and sand (in foul position) etc complete all as specified. (v) Contractor shall engage the above mentioned T&P and intimate to Engr-in-Charge in writing with machine No / Vehicle No etc for their record and prior approval. (vi) The T&P as and when brought by the contractor based on site requirement, the concerned site executive shall take a photograph of machine along with the supervising staff i.e. JE's and contractor's representatives etc and same shall be kept in record with date. (vii) Pucca bound register shall be maintained showing the machine no / vehicle no and their deployment at site mentioning time and date duly signed by concerned JE, Engr-in-Charge and contractor and the same register shall be produced while claiming the payment by the contractor.

Dismantling of PVC cast iron 110mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

Supply and fixing PVC (SWR) pipe single socketed of 110mm dia in any length with rubber washer ring joint fixed to wall complete all as specified and as directed.

Supply and fixing PVC (SWR) bend of 110mm dia complete all as specified and as directed.

Dismantling of PVC cast iron 75mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

Supply and fixing PVC (SWR) pipe single socketed of 75mm dia in any length with rubber washer ring joint fixed to wall complete all as specified and as directed.

Supply and fixing PVC (SWR) bend of 75mm dia complete all as specified and as directed.

Cutting into existing manholes for connecting new drain 150mm dia making good to pipe and rendering cutting out existing for and forming branch channel (½ round or 3/4 round section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required complete all as specified and as directed.

Cutting into existing manholes for connecting new drain 200mm dia making good to pipe and rendering cutting out existing for and forming branch channel (½ round or 3/4 round section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required complete all as specified and as directed.

Dismantling floors, hearth or wall tiling including cement mortar bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Material and labour for precast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab fixed in position including necessary form work and set in cement mortar (1:6) complete all as specified and as directed. Note: - Reinforcement will be measured and paid separately.

Material and labour mild steel TMT 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Supply and fixing in repair Vitreous china squatting pan 'Orissa' pattern size 580x440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe, anti-syphonage pipe, etc. complete making good to floor as existing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flush pipe and joints complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Vitreous china bowl urinal flat back, size of 465 x 355 x 265mm white including waste pipe 32mm dia galkvanised iron pipe, grating and brass union for discharge pipe complete including providing and fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug with and including 60mm long brass screw pointing around urinal back in cement etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC low level flushing cistern valveless, syphonic action type of 10 litres capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, PVC connection (15 x 450 mm) long complete all as specified and as directed.

Supply and fixing in repair Vitreous china wash hand basin white flat back end of size 550 x 400mm including brackets, cutting for and pinning in ends for brackets, erecting stand complete including brass chromium plated waste coupling and PVC 32mm bore waste pipe with chain and plug and porcelain stopper complete all as specified and directed.

Supply and fixing in repairs pillar tap fancy type chromium plated with capstan head, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipes 15 mm bore dia complete all as specified and as directed.

Supply and fixing PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed.

Supply and fixing in repairs 15mm bore long body bib tap cast copper alloy fancy type chromium plated with capstan handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fixing PVC waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as speciifed and as directed.

Supply and fixing in repairs bib taps, cast copper alloy fancy type chromium plated (long body) with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15mm dia bore complete all as specified and directed.

Supply and fixing in repairs chromium plated angular stop cock PTMT, cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe of size 15mm dia bore complete all as specified and directed.

Supply and fixing in repair grating doom 100mm dia without hole chromium plated complete all as specified and as directed.

Supply and fixing in repair grating doom 100mm dia with hole, chromium plated complete all as specified and directed.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles 300 x 450 x 7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including taking down old plaster and 10 mm thick screed in cement mortar (1:4) complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 15mm complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm complete all as specified and directed.

Supply and fixing steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm complete all as specified and as directed.

Supply and fixing steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20mm complete all as specified and directed.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

Complete removal of vegetations, roots and shurbs from wall and making good the wall with PCC (1:2:4) type B-0 not exceeding 1 Sqm including necessary arrangement of all scaffolding upto 12 metre height of building complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area complete all as specified and directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggrregate) as in plinth, path etc surface finished even and fair finish complete all as specified and as directed.

Material and labour for machine pressed precast conctete interlocking paver block with grey cement and pigment, any shape and size confirming to IS : 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and as directed.

Material and labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Supply and fixing chequered coloured cement concrete tiles 30cm x 30cm x 25mm thick set, jointed and pointed in cement slurry in floors with grey pigment cement and pigments including and over 15mm thick screed bed or bedding layer of cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles finish complete all as specified and as directed.

Material and labour for cement concrete (1:5:10) in type E-2 (using 40 mm graded crushed stone aggregate) as in foundation, sub base etc complete all as specified and directed.

Material and labour for plain cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels and drains including formwork complete all as specified and as directed.

M/s Koul & Sons

bushan kumar

ASHFAQ AHMED MANHAS

Bidder Name

ASHFAQ AHMED MANHAS

M/s Koul & Sons

bushan kumar

M/S LANGER CONSTRUCTION CO