Augmentation of Raw Water S...

Amount

Designing, constructing, Erecting, Commissioning, testing and Trial Run of 08 MLD net capacity Automated PLC controlled Water Treatment Plant including SCADA automation system with SCADA Room, 01 nos split Air Conditioner 2.0 ton, RAW water pumping station (Including Inlet pipe and Rising Main) Rapid Gravity Filter bed with media from Ghaggar or other approved mining, Pipe Gallery, Chemical /Lab Building (50 M^2),Electrical Building(60 m^2), Administrative Building (30m^2), 02 nos toilet, Kota stone flooring in all covered area, all windows and doors of UPVC Pannel and glass, Filtered water 08 MLD Approved pipe from filter house to CWR, waste water sumps, sludge thickener, supernatant rate Tank and recycling pump, Sludge Drying Beds including drainage system,6 Nos Chlorine toner duly filled,Chlorinators,3 MT EOT for toners and alum handling, all electrical control panel, internal electrical fitting and lighting, DI pipes, valves, Gates, Special Flow meter, instrumentation and all other contingent works likes distempering painting and other finishing works there to require for completion and commissioned the WTP as per DNIT. A) Complete Civil Work: B) Complete Mechanical Work: C) Complete Instrumentation Work:

Supplying erection, testing of fully automatic electric control panel board for Pump Chamber consisting of MS sheet of thickness 14 gauge duly painted box type floor mounted made of angle Frame containing 1 no. fully automatic air brake starter suitable for Motor of the following capacity, Min switch of suitable range with HRC fuse, 1 no. volt meter (0 to 500 volts), 1 No. Amp. Meter of 0 to 100 amp. 3 sets of indicating lamp capacitor of suitable capacity and 1 no. single phase preventers with the timer switch including wiring in panel board and suitable electric energy meter wiring in Electric Control Panel Board complete in all respect as per specification given in Schedule No. II, complete in all respect. =for raw water lifting pump set 11000 LPM X 15 Mtr Head

Supplying, erection, testing and commissioning of Horizontal spilt casing pump set for for raw water having head 15.00 m as per the indicated requirements of discharge in LPM and power capacity in BHP as per IS marked including all accessories (like SS Pipes, SS Chain (Shackle Chain) ,SS Foundation Bolt, complete base frame, Monorail, Chain Guide Line, Auto Compiling, Duct Foot Bend (D/F Bend) etc complete in all respect. 11000 LPM X 15 Mtr Head (for raw water lifting in S and S tank)..

Supplying, erection, testing and commissioning of Horizontal spilt casing Non-clog pump set for for raw water having head 15.00 m as per the indicated requirements of discharge in LPM and power capacity in BHP as per IS marked including all accessories (like SS Pipes, SS Chain (Shackle Chain) ,SS Foundation Bolt, complete base frame, Monorail, Chain Guide Line, Auto Compiling, Duct Foot Bend (D/F Bend) etc complete in all respect. 6200 LPM X 12 Mtr Head (Raw water filling in WTP)

Supplying erection, testing of fully automatic electric control panel board for Pump Chamber consisting of MS sheet of thickness 14 gauge duly painted box type floor mounted made of angle Frame containing 1 no. fully automatic air brake starter suitable for Motor of the following capacity, Min switch of suitable range with HRC fuse, 1 no. volt meter (0 to 500 volts), 1 No. Amp. Meter of 0 to 100 amp. 3 sets of indicating lamp capacitor of suitable capacity and 1 no. single phase preventers with the timer switch including wiring in panel board and suitable electric energy meter wiring in Electric Control Panel Board complete in all respect as per specification given in Schedule No. II, Including MCB, suitable, Capacitor, Wooden Box etc as per site requirement complete in all respect. for 6200 LPM 12 mtr head.

Supply and fixing of Gantry with motor rise machine (tested for 1.5 times the rated capacity) including travelling trolley of appropriate lifting capacity I section as per IS code 3177:1999 with up to date amendments for handling of pumping sets capable of moving along the girders including cost of suitable sized RCC pillars to be provided in pump house complete in all respects as per directions of Engineer in charge 3 ton capacity

Designing, Supply and erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 plus (-)1% volts AC alternator coupled directly through a set of flexible coupling = 700 KVA The DG set should be according to CPCB IV plus draft notification effective from 1 july 2023 norms or any other upto date norms according to CPCB/Govt. complete in all respect. 700 KVA (BS-VI compliance)

Supplying, erection, testing and commissioning of horizontal motor pumping set for clear water having head 45.00 m as per the indicated requirements of discharge in LPM and power capacity in BHP as per IS marked. BHP 70 LPM 4050 x 45 m head

Supplying erection, testing of fully automatic electric control panel board for Pump Chamber consisting of MS sheet of thickness 14 gauge duly painted box type floor mounted made of angle Frame containing 1 no. fully automatic air brake starter suitable for Motor of the following capacity, Min switch of suitable range with HRC fuse, 1 no. volt meter (0 to 500 volts), 1 No. Amp. Meter of 0 to 100 amp. 3 sets of indicating lamp capacitor of suitable capacity and 1 no. single phase preventers with the timer switch including wiring in panel board and suitable electric energy meter wiring in Electric Control Panel Board complete in all respect as per specification given in Schedule No. II, complete in all respect. for 4050 LPM X 45 Mtr Head

(-) Less Credit of surplus earth

Providing and fixing C.I. AIR valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately): 500 mm i/d

Providing and fixing Cast Iron Detachable Joints class-15 marked with IS: 8794 for use with asbestos cement pressure pipes complete with 2 Nos. rubber rings marked with 15:5382 and IS:10292 and appropriate number of nut and bolts marked with 15:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (Excavation will be paid separately) 500 mm i/d

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately): 500 mm i/d as per approved vendor / material list

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately): 400mm i/d as per approved vendor / material list

Providing and fixing Cast Iron Detachable Joints class-15 marked with IS: 8794 for use with asbestos cement pressure pipes complete with 2 Nos. rubber rings marked with 15:5382 and IS:10292 and appropriate number of nut and bolts marked with 15:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (Excavation will be paid separately) 400 mm i/d

Providing and fixing of Stainless-steel cover 3` x 3` for sluice valve hodi, cover made of SS-304 grade sheet in 16 gauge and frame of SS-304 angle including cutting, bending, fitting charge complete in all respect as per satisfaction of Engineer-in-Charge.

Supply and Fixing of Dismantling Joints/ Expension Joint, between the pump and Sluice valve PN 1.6 complete in all respect. 250 mm

Supply and Fixing of Dismantling Joints/ Expansion Joint, between the pump and Sluice valve PN 1.6 complete in all respect. 300mm i/d

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately): 400mm i/d as per approved vendor / material list

Providing and Fixing of the GI reverse guage stripe in the clear water tank complete in all respect as per satisfaction of Engineer-in Charge

Providing and Fixing of S.S. cover and frame for V.notch hodi, CWT opening, Clear Water Sump Well opening cover of size 0.800 x 0.800 m made out of stainless steel grad 304 sheet of SS frame cover and fitting charge complete in all respect as per satisfaction of Engineer-in-Charge (for Clear water tank)

Providing Fixing Led light of 50watt (Syska, Havells, Philips make)

Providing Fixing Led light of 9 watt (Syska, Havells, Philips make)

wall fan of size Sweep 40 cm (400 mm) Speed 1280 rpm Power Input 55 W

Operation and maintenance of 8 MLD WTP and complete scope of work under this contract as per Operation and maintenance Manual of NIT (Attached in additional Documents) for a period of 5 years after 12 month defect liability period and 3 months trial run period. (charged to A/Mtc estimate year wise) complete in all respect. Operation and maintenance during defect liability period (Operation only) after 3 months trial run period

Operation and maintenance during 2nd year.

Operation and maintenance during 1st year after DLP

Operation and maintenance during 3rd year

Operation and maintenance during 4th year

Operation and maintenance during 5th year

Bidder Name

Amount

Bansal Construction Co, Gurgaon (GSTN-06AAFFB1840G1ZW) BID ID -1326445

M/S SHREE BALAJI BUILDERS (GSTN-NA) BID ID -1327914

Rakesh Yadav Contractor (GSTN-NA) BID ID -1326271

ANAND KUMAR CONT (GSTN-NA) BID ID -1327626

M/s Sourabh Construction Pvt. Ltd. (GSTN-NA) BID ID -1327896

VISHNU PRAKASH R PUNGLIA LIMITED (GSTN-NA) BID ID -1328169

Bansal Construction Co, Gurgaon (BID ID -1326445)

ANAND KUMAR CONT (BID ID -1327626)

VISHNU PRAKASH R PUNGLIA LIMITED (BID ID -1328169)

M/S SHREE BALAJI BUILDERS (BID ID -1327914)

Rakesh Yadav Contractor (BID ID -1326271)

M/S SHREE BALAJI BUILDERS (BID ID -1327914)

M/s Sourabh Construction Pvt. Ltd. (BID ID -1327896)

VISHNU PRAKASH R PUNGLIA LIMITED (BID ID -1328169)

ANAND KUMAR CONT (BID ID -1327626)

Rakesh Yadav Contractor (BID ID -1326271)