SPECIAL REPAIR OF SENTRY GUARD POST CUM REST

Amount

Taking down chowkaths or frames n.exc 1.5 sqm each (without taking off shutter from the frame) complete all as specified and directed.

All as per item No. 1.00 above area exc 1.5 Sqm but not exc 4.00 Sqm.

M&L pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in filling pressed steel frame /hold fast blocks etc complete all as specified and directed.

S&F 2nd class HW 35 mm thick factory made Plain framed, panelled shutter of rail and style (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick Glazed and skeleton shutters of 2nd class hardwood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); and fitted to chowkaths complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings n.exc 15 cm thick below or above ground level etc including removing outside MoD land in low lying area complete all as specified and as directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F Butt hinges, 100mm size stainless steel, bright polished and fixed complete all as specified and directed.

S&F 250mm size aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of syntheatic enammel paint over one coat of pink primer complete all as specified and directed.

Dismantling structural steel work including doors, railing/stair case gates but excluding framed truss etc. complete all as specified and directed.

S&F framed work such as grills, grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; stair railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F for Fe 290 (Gde E-165) steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F welded steel wire fabric supplied and fixed complete to steel members weight not exc. 4 kg/sqm complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel and fixed of 100 mm size complete all as specified and directed.

S&F mild steel sliding door bolts 200 mm length, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nut, four on bolt plate and two on staple plate complete all as specified and directed.

M&L for preparation of newly steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 25 mm dia PVC coated MS curtain rod with required brackets with teak finish apearance etc complete all as specified and directed.

S&F decorative type funnel on both end of curtain rod with teak wood finish appearance complete all as specified and directed.

Preparation of newly steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) including removing outside MoD land in low lying area complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub-base, finished fair and even for receiving tile complete all as specified and directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing rubbish off the premises etc including removing outside MoD land in low lying area complete all as specified and directed.

M&L non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match colour of tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed.

M&L for Glazed coloured designer ceramic tiles in vertical surface of size 450x300mmx7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles with including 10mm thick cement plaster on wall in CM 1:4 complete all as specified and directed.

M&L for demolition of stone slabs, old granite/Kota stone as in plateform and tiles/flooring of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar including removing outside MoD land in low lying area complete all specified and directed.

M&L 18-20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including, cutting, rubbing, grinding and mirror polishing and moulding with beveling half round edges of stones in steps upto desired satisfaction of Engineer-in-Charge complete all as specfied and directed.

M&L machine cut kota stone slab 18-20mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing and moulding with beveling half round edges of stones in steps complete all as specfied and directed. Note for item No 28 & 29 :- Full length kota stone slab should be used in stair steps (No pieces of kota stone to be used)

M&L for 16 to 18mm thick granite stone slab as in shelves, in steps, jambs, pillars, window cills, cooking platforms, flooring and like work ,machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding with moulding beveling half round edges of stones and polishing laid over 15 mm thick screed bed in CM 1:6 etc complete all as specified and directed.

M&L for 16 to 18mm thick granite stone slab on vertical surfaces such as skirting/dado including grinding and polishing etc set and jointed with grey cement slurry and pointed with white cement with admixtur of pigment to match the shade of granite stone and beveling half round edges of stones fixed over and including rendering 10 mm thick CM 1:3 etc complete all as specified and directed.

M&L cement concrete type D2 1:4:8 (40mm graded stone aggregate) in sub base, filling and mass-concrete complete all as specified and as directed.

M&L pre-polished coloured designer chequered cement concrete tiles of size 30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry in floors using with grey cement and pigment, over & including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

Material and labour for PCC (1:3:6) Type C-2 (20 mm graded stone aggregate) as in plinth protection / path 75 mm thick laid in bays incl finishing the concrete surface even and smooth w/o using extra cement complete all as specified and directed. Note: The unit rate quoted shall be deemed to include for providing the concrete in alternate bays n exc 3 mtr long with 12 mm wide and 50 mm deep joint between the bays which shall be filled with mastic filling with hot bitumen 85/25 and 1:2 mix by volume.

M&L factory made coloured designer PU moulded polished with coating material, concrete interlocking paver block with Grey cement and pigment, any shape and size, 60 mm thickness, M-35 grade complete all as specified and directed.

M&L for sand filling 40 mm thick under interlocking tiles watering and consolidation complete all as specified and directed.

S&F steel water tubing 40 mm bore, medium grade, galvanised with all fitting and fixed to walls and ceiling or laid in floors etc complete all as specified and as directed.

S&F in repairs PVC soap tray, 350x100x60mm, fixed to wall with plugs with chromium plated screw complete all as specified and as directed

S&F in repair GI pipe 20mm dia medium grade with all fittings and fixed to walls ceiling, floor & trenches etc complete all as specified and directed.

S&F in repair GI pipe 15mm dia medium grade with all fittings and fixed complete to walls complete all as specified and directed.

Cutting chases, pinning in, for brick walls built in cement mortar, making good in cement mortar 1:3 or PCC M-15 (nominal mix) type B-0 (using 12.5 mm graded stone aggregate) and finish to match with the existing as required for inserting corrugated sheets and concealed water tubing etc cutting exceeding 10 cm girth but not exc. 20 cm complete all as specified and as directed.

S&F in repairs vitreous china, squtting pan water closet orissa pattern of size 580 mm x 440 mm white with integral foot rests (including flush pipe but excluding flushing cisterns) including connection to trap and flushing pipe, anti syphonage pipe etc and making good complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pedestal pattern white excluding fixing bolts, flushing cistern and flush pipe complete but including PVC seat cover with aluminium hinging devices & EWC Jet chromium plated with 1.00 mtr long PVC connection pipe etc complete all as specified and directed.

S&F in repairs PVC low level flushing cistern valveless syphonic action type 10 litres capacity with inlet ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC complete all as specified and as directed.

S&F in repair vitreous china urinal, Half stall type, white with grating, union for discharge pipe, PVC flush pipe and waste pipe, CP urinal Spreader fixed to water supply pipe etc complete all as specified and directed.

S&F PVC P or S Trap 100 mm dia etc complete all as specified and directed.

S&F grating dome 125 mm dia with waste hole of CP complete all as specified and as directed.

S&F in repairs CP brass bottle trap 32 mm dia including joining to waste fitting and waste pipe complete all as specified and as directed.

S&F Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 grams) complete all as specified and as directed.

S&F in repairs PVC connections 15mm dia 450 mm long with PTMT nut on both ends and washers complete all as specified and as directed.

S&F in repairs 15mm bore pillar taps fancy type, half turn CP brass with capastan heads, scewed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nut, screwed for iron pipes and fixed complete all as specified and directed.

S&F in repairs bib taps 15 mm bore chromium plated, long body fancy type, half turn cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair WHB vitreous china, white, flat back, size 550x400 mm incl brackets, waste coupling,waste pipes etc complete all as specified and as directed.

S&F in repairs stop valves/angle valves cast copper alloy CP concealed fancy type half turn screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 20mm dia complete all as specified and as directed.

S&F in repairs stop valves/angle valves cast copper alloy CP concealed fancy type half turn screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 15mm dia complete all as specified and as directed.

S&F PTMT ball valve high pressure with polylethylene float ball and fly nut complete screwed for iron pipe and fixed ,20 mm bore ,fixed in repairs complete all as specified and directed.

Dismentling of old unservicable PVC water tank of capacity 500 ltr to 1000 ltr complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank (Cylindrical vertical withclosed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples complete all as specified and as directed.

S&F tank Nipple suitable for HDPE water tank. (Minimum weight 20mm-45gms complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia ‘D’ type 60 cms long between flanges complete all as specified and directed. Make: CERA Cat part No. F5004103 or equivalent approved.

S&F in repair toilet paper holder Chromium Plated as approved & directed by Engr-in-charge etc complete all as specified and directed. Make: CERA Cat part No. F5003110 or equivalent approved.

S&F chromium plated soap dish fixed to wall with CP brass screws etc complete all as specified and directed. Make: CERA Cat part No. F5004106 or equivalent approved.

S&F in repair 75mm dia ivory gold over head shower rose with revolving joints & 150mm long swivel shower arm suitable for 15mm bore GI pipe etc complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipe in any length with rubber ring joints fixed to walls as in vent pipe including PVC cowl etc complete all as specified and directed.

All as per ser item No. 65.00 above but 110mm bore.

S&F in repair 110 mm bore PVC (SWR) bends complete all as specified and directed.

Demolition of brick work built in cement mortar of any description etc complete all as specified and directed.

M&L brick work with subclass 'B' bricks old size, in one brick thick wall, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster from brick or stone wall etc including racking out joint, hacking for key scrubing down with water etc complete all as specified and directed.

M&L for Rough cast plaster including 15mm thick rendering in CM 1:3 on brick work or concrete surfaces complete as specifed in SSR Part-I clause 14.22 complete all as specified and directed. Note:- Rough cast finish to be as below :- After applying the under coat of cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generallly of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered.

M&L for 15mm thick rendering on brick work or concrete surfaces in CM 1:6 finished even and fair etc complete all as specified and directed.

M&L for 15 mm thick Rendering on brick work or concrete surfaces in CM 1:4 mixed with WPC@3% of cement weight or as per manufacture's instruction finished even and smooth without using extra cement complete all as specified. Note:- WPC shall be measured and paid separately.

M&L 5 mm thick cement plaster in CM 1:3 as in soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth w/o using extra cement etc complete all as specified and directed.

Supply only integral water proofing comound/liquid etc complete all as specified and directed.

Complete removal of existing treatment from internal / external plastered or unplastered surfaces of walls complete all as specified and directed.

M&L for applying two coat of wall care putty (min 1 mm thick of each coat) on wall including preparation of surfaces complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion on wall including preparation of surfaces etc complete all as specified and directed.

M&L for two coats of acrylic exterior emulsion paint (weather proof coat) of any tint including priming with alkali resistant primer paint on external cement plastered surfaces complete all specified and directed.

Complete removal of existing treatment from plastered or unplastered or concrete surfaces of ceiling complete all as specified and directed.

M&L for three coats of white lime wash on plastered surfaces of ceiling including preparation of surfaces etc complete all as specified and directed.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for chipping of spalled and loose concrete and cleaning rust from reinforement by sand blasting scrubbing down concrete surface with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bounding coat of approved epoxy adheisve on complete exposed surfaces of concrete to be gunited all as specified and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperature 75mm, total thickness of gunite n.exc 40mm thick (average thickness) in cement mortor (1:2) using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturer instructions and finally applying cement plaster over gunite surface of required thickness to give even uniform and smooth finish conforming to proper geometrics in cement mortar (1:3) to match the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias,parapets, lintels, columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 6 storey building including removing of small trees shrubs etc all as specified and as directed.

Roughening surfaces of old concrete floor/roof by taking down plaster , picking, sweeping clean and washing down with water to remove dust complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregates) as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, etc complete all as specified and as directed.

M&L for plaster 20mm thick in CM (1:3) on roof surfaces mixed with WPC@3% by weight of cement or as per manufacturer's instructions finished even and smooth without using extra cement including making groove in plaster complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for plain cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) as in roof kerbs, benching and the like, etc complete all as specified and as directed.

S&F for factory made steel ventilators/window box type glazed shutter made out of 16 gauge steel section for frames & shutters as per drawing No TD-A sheet No. 01/03 to 03/03 with openable glass shutters including pintel hinges 75mm long 12mm dia, 100mm long handle and tower bolt 150mm long, MS hooks & eye 150mm long all as applicable including one coat of red oxide primer complete all as specified and directed. Note:- Glass shall be measured and paid separetely.

S&F factory made steel window/ventilator box type made out of 16 gauge steel section for frames & shutters as per drawing No TD-A sheet No. 01/03 to 03/03 with openable both glass and guage shutters including pintel hinges 75mm long 12 mm dia, 100mm long handle and tower bolt 150mm long, MS hooks & eye 150mm long all as applicable including one coat of red oxide primer complete all as specified and directed. Note: GLass & wire mesh shall be measured & paid separetely.

Hacking out old broken glasses (any thickness) size quality or description from wooden/steel frame etc complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n-exc 0.50 sqm in each pane etc complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc complete all as specified and directed.

M&L for preparation of primed surface of steel of any description over 10 cm width of girth not otherwise described applying two coats of synthetic enamel paint complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.

All as per Item No. 94.00 above but including taking down.

S&F 4.5mm to 5.00mm thick tinted glass including with powder coated aluminium frame size 60x40x1.50mm including glazing clips rubber beading and aluminium beading for aluminium door /window area of each panes exc 0.5 sqm complete all as specified and directed.

S&F in repair 125mm to 175mm hat pegs of aluminium, solid body fixed with screws complete all as specified and as directed.

Taking down carefully unserviceable point wiring (light, fan and power socket etc.) complete including fittings such as switches, ceiling roses,pandent ,regulators, sockets etc and making good of distrubed surface complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm copper conductor FRLSH (Multi stranded) ISI Marked PVC insulated unsheathed cable in and including concealed type PVC conduits, medium grade, ISI marked not less than 20mm dia with all fittings/accessories with and including FRLSH PVC insulated ISI Marked unsheathed cable 1.5 Sqmm copper multistranded conductor FRLSH as earth wire and connected to common earth dolly and including GI terminal boxes and joint boxes of suitable size made of 1.6mm thick sheet (for mounting switches sockets, light fittings etc) covered with modular cover plate for one light point or fan point or one bell/point controlled by one switch complete all as specified and directed including making good the disturbed surface and matching with existing surfaces.

All as per ser item No 99.00 above but one 3 pin socket outlet 5 Amps independent.

All as per ser item No 99.00 above but one 3 pin socket outlet 5 Amps on same board.

All as per ser item No 99.00 above but with size of cable 4 Sqmm for power point, 2 in 1, 5 pin socket outlet 15 Amps independent control by one switch.

M&L for taking down of ceiling fan 1200/1400mm sweep, metal body type single phase 240 volts AC, keeping aside for general servicing i.e. greasing/oiling including cleaning, painting with synthetic enamel paint by spray machine & including marking of MES No, etc and hanging the same in position including making all electric connections & testing complete all as specified and directed.

All as per ser item No 103.00 above but exhaust fan any size/type.

S&F modular switch single pole one way 6 Amps 1 module complete all as specified and directed.

S&F modular switch single pole one way 16 Amps 1 module complete all as specified and directed.

S&F modular socket 6 Amp 2 in 1, 5 pin combined 2 module complete all as specified and directed.

S&F modular socket 6 A/16 amp -2/3 pin combined 2 module complete all as specified and directed.

S&F in repair SPN DB 8 ways with 200 amps rated busbar 230 volt double door complete all as specified and directed.

S&F in repair SPN DB 12 ways with 200 amps rated busbar 230 volt double door complete all as specified and directed.

S&F in repair MCB SP, C-curve, 230 volts 40 Amps 10 KA complete all as specified and directed.

S&F in repair MCB SPN, C-curve, 230 volts 40 Amps 10 KA complete all as specified and directed.

S&F metal flush box 4 module complete all as specified and directed.

S&F metal flush box 3 module complete all as specified and directed.

S&F metal flush box 6 module complete all as specified and directed.

S&F metal flush box 12 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 3 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 4 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 6 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 12 module complete all as specified and directed.

S&F Wall mounted 22 watt, 6000K (4 Feet) LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver including taking down of unserviceable fittings complete all as specified and directed. Make:-Havells Cat part No. LHEXBTP7IN1S022 or equivalent make of philips/C&S.

S&F in replacement of energy saving new generation 9W LED linear and compact mirror light fitting 6000K complete all as specified and directed. Make:-Havells Cat Part No. LHEXBXP7PN1W009 or equivalent make of philips/C&S.

S&F in replacement of slim surface mounted square LED panel 12Watt, 6000K al. die cast body with premium diffuser to ensure glare free and even distribution of light. Including provision 2 core wire for making connection from ceiling rose or connector to light complete all as specified and directed. Make-Havells cat part No. LHEAAWP5IL1W012 or equivalent make of phillips/C&S.

M&L for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised earthwire 4mm dia by means of nuts bolts, check nut and washers of galvanised iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40 cm x 40 cm x 50mm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifting made out of 8 mm dia MS bar, funnel, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal, and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I.

Excavation in treches in soft/loose soil not exceeding 1.5m depth & not exceeding 1.5m in width over energised LT cables for carrying out brick work for preparation of cable duct including for taking out complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm thick as in soft/loose soil complete all as specified and as directed.

Removing excavated/surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed.

Supply & lying dry fine sand for cushioning of underground cable laid in trenches/duct complete all as specified and as directed.

M&L for sub class 'B' burnt brick flat across the cable, for protection of cable laid in trenches complete all as specified and directed.

Supply, lying, connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 core including taking down old unserviceable cable complete all as specified and directed.

S&F MCB TPN DB 4 way with 200 amps rated busbar 415 volt double door complete all as specified and as directed.

S&F wiring for circuit/submain wiring along with earth wire of FRLSH PVC insulated copper conductor single core cable in surface/recessed of size 2x6 sqmm+1x6 sqmm earth wire including 20 mm dia PVC conduit and lugs/thimble with nuts, botls and washers etc complete.

S&F MCB isolator TPN 63 Amps C-Curve 415 volt with breaking capacity 10 KA all as specified and as directed

V.V CONSTRUCTIONS

JM enterprises

R.K ENGINEERS & CONTRACTORS