Construction of Tehsil Office at Barbugh Shopian

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.(All kinds of soil :)

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts,wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Providing and laying stone soling tightly hand packed under foundations, footings ,floors etc. including carriages of materials from source to site of work complete in all respects.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering all works upto plinth level.:-1:4:8 ( 1 cement: 4 coarse sand: 8 graded stone agg/ 40mm nominal size) Crushed aggregate)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement.:-1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) All works upto plinth level.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement.:-1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) All works above plinth level upto floor V level

Reinforcement for R. C. C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars .( All work at all levels complete.)

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering all works upto plinth level :-1:2: 4( 1 cement: 2 coarse sand: 4 graded stone agg/ 20mm nominal size) crushed aggregate) for mass concrete works.

Structural steel work in welded in built up sections trusses and framed work, including cutting, hoisting, fixing in position and applying of priming coat of approved steel primer complete in all respects..(All work at all levels complete.)

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing form work including Centering ,shuttering , strutting, propping etc. using ply wood sheeting with water proofing ply board and removal of the same for ( All works at all levels complete.).-Foundations, footings, bases of columns etc. for mass concrete.

Providing form work including Centering ,shuttering , strutting, propping etc. using ply wood sheeting with water proofing ply board and removal of the same for ( All works at all levels complete.).-Floor beams, plinth beams, girders, bressumers and cantilevers. Etc

Suspended floors, roofs, landings, balconies and access platform with waterproofing ply 12 mm thick

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc linner walls

Edges of slabs and breaks in floors and walls (Under 20 cm wide)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing and fixing Colour Coated High Rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness )

Providing ridges or hips of width 60cm overall width plain Coloured fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.:-(0.50 mm thick with zinc coating not less than 275 gram/m2

Brick masonry with FPS bricks of class designation 75 in super structure up to floor V level in cement mortar 1:6 (1cement: 6 cement coarse sand). complete in all respects

Providing wood work in frames for doors, windows, clerestory windows and other frames Wrought framed and fixed in positions (Ist class Imported K.D wood ).

Providing and fixing 35 mm thick paneled door shutters (Ist class Kail Wood). With 25-30 mm thick Ornamentals Kail Wood panels including necessary stainless Steel Butt hinges /screws etc. Design of shutter and panels as per the instructions of Engineer incharge complete in all respects.

Providing and fixing glazed shutters for windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.(2nd Class kail wood) 30 mm thick shutters (Ist class Imported K.D wood )

Providing and fixing paneling or paneling/ glazing in paneled or paneled & glazed shutters for windows and clerestory windows (Area of opening for panel inserts excluding portion in side grooves or rebates to be measured). Paneling for paneled or paneled glazed shutters.(Fixed Glasses 4 mm thick in Glazed Portions)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : ( class kail wood.)

Providing and fixing Providing and fixing G.I Coloured Soffits fixed on steel frames/trusses of required size readily available with necessary screws/ fitiings complete as per the directions and designs approved by Engineer Incharge -

Providing and fixing G.I Coloured sheet Eaves boarding readily available of 200 mm/ or of required size with necessary screws/ fitiings complete as per the directions and designs approved by Engineer Incharge -

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand:4 graded stone agg.) finished with a floating coat of neat cement including cement slurry but excl. the cost of nosing of steps etc. complete. (40mm thick with 20mm nominal size crushed stone aggregate)

Providing & fixing glass strips in joints of terrazzo/cement conc. floating (40mm wide and 4mm thick).

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(600 x 600 mmm)

Providing and laying Ceramic glazed floor tiles 300x300/450 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. (In colour such as White, Ivory, Grey, Fume Red Brown)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (Complete as per Sample approved by Engineer )

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding tubes channels, plates etc. including welding ,grinding, buffing, polishingand making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slabwith suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Extra for Providing & fixing of stainless steel navel post (Ornamental) including top ball of 304 grade of required height duly anchored to floor with dash fasteners Complete as per the directions of Engineer incharge.

12 mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand)

6 mm cement plaster to ceiling ,soffits etc of mix 1 : 3 (1 cement : 3 fine sand) . Upto floor V level complete

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (2mm thick)

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work and wooden based surfaces complete.(including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new work)

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.(Two coats)

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) .(Two coats)

Providing and fixing 15 mm thick T&G planks made of imported wood (New zealand pine or equivalent) on wood work in false ceiling, wall/wall partitions sawn and put up in position ( budloo wood Ceiling Joists of 50 mm x 65 mm in sections placed @ 600 mm C/C both ways or as required at site). including cost of necessary Cornices/beadings of Kail wood of required sizes (wherever required) / adhesive & cost of nails etc. all complete upto floor 5 level as per the directions of Consultant / Engineer-in-charge .(For panelling /Ceilings etc.) including painting two coats

Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of necessary frame work /cornices etc. which is to be paid for separately (Paanch Murabah)

Providing and fixing 12 mm thick Commercial ply of approved brand and manfacture for frame works underneath to Khatambandi Ceilings fixed with necessary screws/nuts & bolts/ nails, as required complete in all respects as per direction of Engineer-in-charge

Providing and fixing 75mm x 50 mm/2 Cornices of Ist calss budloo wood to Khatambandi Ceilings fixed with necessary screws/nails etc. as required complete in all respects as per direction of Engineer-in-charge

Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer Incharge/ consultant, complete as per the specifications (Aluminium fittings ) (Anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Providing and fixing bright finished brass tower bolts (Aluminium ) with necessary screws etc. complete. For Doors 200x10 mm

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer Incharge/ consultant, complete as per the specifications (Aluminium fittings ) (Anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Providing and fixing bright finished brass tower bolts (Aluminium ) with necessary screws etc. complete. For Windows100 mm

Providing and fixing bright finished brass handles with screws etc. completeFor Windows100 mm

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), ins

ide plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :-( Inside dimensions 455x610 mm and 45 cm deep for single pipe line-)

Providing and Fixing of PVC pipes of Type B (PRINCE MAKE) with washers & jointing compound complete water tight. Complete in all respects of the following nominal dia. Complete in all respects.( 110 mm nominal outer dia Pipes)

Providing and Fixing PVC Plain Bend including rubber washers etc complete water tight Complete in all respects of the following nominal dia.

Providing and Fixing PVC Door Bend including rubber washers etc complete water tight Complete in all respects of the following nominal dia.

Providing and Fixing PVC Floor /Nahani Trap 75 mm (Multi Junctions) including grating , rubber washers etc complete water tight Complete in all respects .

Providing and Fixing P-Trap 110mm including rubber washers etc complete water tight Complete in all respects .

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. (Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.)

Providing and fixing of CP Bath fixtures/fittings of Approved brand as desired by Engineer I/C.of the following nominal bore/dia. 15mm dia Bib Cock

Providing and fixing of CP Bath fixtures/fittings of Approved brand as desired by Engineer I/C.of the following nominal bore/dia.15mm dia Angel Value

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) 20 mm dia. nominal bore (Medium Grade B class)

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests).

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Construction of Soakage pits by way of Providing and fixing of Pre cast Reinforced Cement Concrete Rings of 900 mm internal dia of specified thickness /design fixed with top RCC Cover (Cover and excavtion shall be paid for Seperately),including handling,hoisting , fixing in position and making holes for fixing of Pipes as required complete upto a required depth including neatly filling top with excavated earth / soil as directed by site engineer complete in all respects

Providing RCC Cover at top of Soakage pit 1200 mm dia ,including handling,hoisting , fixing in position complete including cost of covering the top with surplus excavated earth up to 300 mm thickness or as per the requirment complete.

Carriages of materials from source to Site of work by mechanical transport complete as per the site requirements Stone Aggeregate 40 mm nominal Size and above for an average lead of 20 Kms

Carriages of materials from source to Site of work by mechanical transport complete as per the site requirementsSand/ Stone Aggeregate 20 mm nominal Size and below for an average lead of 20 Kms